Your enthusiasm and knowledge makes me deliriously happy, ‘glad to discover you today. I built my Page Dragon partscaster from a reseller body/bridge, it was my first Tele. I opted for a U.S. neck, 4-way switching and boutique p’ups and all assembly/finishing myself. I loved it so much I’m building another with B&G benders. I’m grateful to see your work and learn new tips, thanks
A little trick with intonating double saddles - raising the saddle on one side has a similar effect to pushing the saddle forwards. Similar because what happens is the string will pull sharper. Usually the higher pitch string of the pair, the middle pair reversed. Set the longest scale string spot-on, intonate the other string by raising and lowering its side. It doesn't take much and barely noticeable.
It's better to adjust the truss rod *before* changing the strings. It saves a lot of time because you can check the relief of the neck with the old strings on and it's no different than if they were new strings. Then just remove the old strings, remove the neck, adjust the truss rod, replace the neck, and string up with new strings. Much simpler that way.
Thanks for putting this together, Matt, very interesting. You briefly mentioned compensated Tele saddles. I'm interested in your opinion on them. Are they systematically a great improvement in terms of intonation? Do you have a preference for the "enhanced" saddles, or the ones where the saddles themselves look just like traditional ones, but which are offset (tilted)? Could this be an idea for a future video?
Defo could do a full video on these. My absolute favourites are the Gotoh Intune Saddles they look like the standard vintage ones but with the intonation points in the correct place, and they don't cost the earth too which is an added bonus.
@@MontysguitarsandpickupsI'm looking forward to it so much I've subscribed! In fact, the subject area is wide enough for two videos; one on compensated saddles, and another one focusing on solutions where the entire Tele bridge is replaced by a six-saddle bridge (Fender make one themselves), or a more contemporary bridge such as is found on the MIM Nashville Deluxe and Player Telecasters, or even the American Elite series. In each video it would be really interesting to see a comparison between the results you were able to attain just doing an accurate-as-possible intonation setup with the traditional 3-pair saddle arrangement, and then seeing to what extent it could be improved by either using compensated saddles (first video), or changing the bridge entirely (second video), on the same - I would suggest affordable - guitar. Just suggestions. I'm sure whatever you put out will be fascinating for Tele aficionados.
I got the JP mirror tele. It's an absolute beast. The neck pickup is magical. You got anywhere I can have a good listen to your 69 Strat set pickups? cheers
I do on my guitars but I love the silky feel you get with freshly polished frets but you don't need to do the t-cut every time. I would recommend naphtha and instrument food every time though. Cheers M
this was nice to watch...ive been tinkering with guitarsetups for a while, but never got into fixing the sadle, seems scary =) and you need expensive set of files and wht not ... how do i dip my toes into this? =)
Glad you liked it man. The nut files are the only real luthier tools you'll need the rest you can get from any hardware store. You used to be able to get single files of the gauges you want but looking around they don't seem to be sold like that now. I'd call a Luthier tool place and see if they can sort you out
@@Montysguitarsandpickups I looked around and you can get sets for whatever strings you use...so 10-46 for example. But I wonder about what to think of when you start on the nut/sadle ... Angles and depth and so on. Cus if you file away to much its not much to do...
@@mudfly3 Hey man sorry for the delayed reply. This is a tricky one but there are ways to fix it if you do go too low, I'll try and do a video specifically on that very soon.
@@Montysguitarsandpickups thanks for replying Monty, that sounds amazing, please let me know if you plan on doing pickups and also what products work best on dark ebony bass wood : ] love the channel
@@Montysguitarsandpickups -be super careful. Tape them up and vacuum particles carefully after you finish. A small particle can finds its way into your pickups and destroy them.
The best way is with lighter fluid and a toothbrush. That will get rid of any stubborn grime. If it is a lacquered board I would polish it with Muc-Off miracle shine, if it is an unlacquered board you Instrument Food or something similar.
Absolutely brilliant .... love watching your videos on insta and on here ! I have a Jimmy Page Tele and now I have seen this I'm wondering if it would be possible to send my jp tele to you for the brilliant upgrade service you have just performed lol ??? Also what kind of price would we be talking ? All the best Matty .
Hey dear chap, glad you liked the video. I can gladly help you out with that. For getting booked in and costings etc email mail@montysguitars.com and the lovely George can fill you in with availability and all the info. Cheers Matt
@@Montysguitarsandpickups Thank you so much Matt , I really appreciate it I will get on to this soon as I get the chance and the dosh ... Thank you again buddy ps... it was me that asked you on insta about re-stringing my Ibanez RG to the E-BALL size 8 but I haven't got a clue how to reset the tremolo :) lol .. thank you ASH
It's a little depressing that for a $1600 guitar you had to go through the trouble of dressing frets and fixing the action. Great video on the process though!!
Why not remove the strings the way most roadie guitar techs do: just cut them off? Saves having to use a drill before snipping them off anyway to pass through the ferrules.
it's about trauma Jefferson . Releasing tensile tension all at once can store unnecessary compensatory tension aberration for posterity. Physics of wood fibers is interesting. Study recurve bows.
@@Montysguitarsandpickups It's All about sound and audio right? :) You can make a microphone like you do pickups... very good pickups. Same thing different name. Ok I'll stop ;) Thanks for the video!
You know it's a good day when Matt's intonation harmonics are in tune with the backing track. :-)
this second that happened 24:55 :O
Your enthusiasm and knowledge makes me deliriously happy, ‘glad to discover you today.
I built my Page Dragon partscaster from a reseller body/bridge, it was my first Tele. I opted for a U.S. neck, 4-way switching and boutique p’ups and all assembly/finishing myself. I loved it so much I’m building another with B&G benders. I’m grateful to see your work and learn new tips, thanks
Thanks Bret, I'm so happy to help. Your Page guitar sounds like a goodn', enjoy the new build. Cheers Matt
With so much contradictory and confusing information around, I honestly think this is the best, easiest to follow guitar set up video I’ve ever seen
My son has a guitar built by young matt (!).... It's a dream to play... Matt. you're a bloody star!
Thanks so much Mark I remember many a good chat with you back in my Candler days. I hope all is well with you man.
Am I watching the England game? No…. I’m m watching Matt sort a Jimmy Page Tele. Love you long time dude
Thanks man!!
Great work Matt - and thanks for the fabulous job on my Les Paul recently!!
I thought I didn’t need to watch this ( I like think I know what I’m doing) but I picked up some great tips!!! Thx Matt :)
A pleasure man
I got your dp51t on a purple squier and shipped it to mississauga canada...I love your pick ups and your you tube channel...you r the best!!!
Thanks man that means a lot!
I've got callaham compensated saddles on a thinline and an esquire..... Makes them so in tune... They look stunning too!!
they make the good stuff
Cracking video all that work building the studio was well worth it
A little trick with intonating double saddles - raising the saddle on one side has a similar effect to pushing the saddle forwards. Similar because what happens is the string will pull sharper. Usually the higher pitch string of the pair, the middle pair reversed. Set the longest scale string spot-on, intonate the other string by raising and lowering its side. It doesn't take much and barely noticeable.
This gives me enough confidence to try this myself!! Thank you Matt!!
A pleasure dear chap. If you get stuck give me a shout.
Great video
Ah Matt gave us the look of ‘disappointment but not surprise’ when he realised the neck screw holes in the body hadn’t been drilled wide enough!
Great advice!
Brilliant set up video Matt , just help me get my telecaster sounding good on Barchords 🎸
Happy to help dear chap
It's better to adjust the truss rod *before* changing the strings. It saves a lot of time because you can check the relief of the neck with the old strings on and it's no different than if they were new strings. Then just remove the old strings, remove the neck, adjust the truss rod, replace the neck, and string up with new strings. Much simpler that way.
Nice and infomazing
I was lucky enough to play this exact guitar as I'm mates with the owner
You know I just got some Monty’s Wax. ( food and relic) and I think it’s brilliant for nut lube as any other product
It's killer for that. I put a small amount on every contact point of the string, it really helps with tuning stability
Thanks for putting this together, Matt, very interesting. You briefly mentioned compensated Tele saddles. I'm interested in your opinion on them. Are they systematically a great improvement in terms of intonation? Do you have a preference for the "enhanced" saddles, or the ones where the saddles themselves look just like traditional ones, but which are offset (tilted)?
Could this be an idea for a future video?
Defo could do a full video on these. My absolute favourites are the Gotoh Intune Saddles they look like the standard vintage ones but with the intonation points in the correct place, and they don't cost the earth too which is an added bonus.
@@MontysguitarsandpickupsI'm looking forward to it so much I've subscribed! In fact, the subject area is wide enough for two videos; one on compensated saddles, and another one focusing on solutions where the entire Tele bridge is replaced by a six-saddle bridge (Fender make one themselves), or a more contemporary bridge such as is found on the MIM Nashville Deluxe and Player Telecasters, or even the American Elite series. In each video it would be really interesting to see a comparison between the results you were able to attain just doing an accurate-as-possible intonation setup with the traditional 3-pair saddle arrangement, and then seeing to what extent it could be improved by either using compensated saddles (first video), or changing the bridge entirely (second video), on the same - I would suggest affordable - guitar. Just suggestions. I'm sure whatever you put out will be fascinating for Tele aficionados.
I got the JP mirror tele. It's an absolute beast. The neck pickup is magical. You got anywhere I can have a good listen to your 69 Strat set pickups?
cheers
Did your pickguard have plastic film on it?
Yep
How much of this process do you do every string change? Do you t-cut, naphtha, instrument food every string change?
I do on my guitars but I love the silky feel you get with freshly polished frets but you don't need to do the t-cut every time. I would recommend naphtha and instrument food every time though. Cheers M
@@Montysguitarsandpickups Sweet. Thanks. Just ordered some can't wait for it to make it across the pond ;)
this was nice to watch...ive been tinkering with guitarsetups for a while, but never got into fixing the sadle, seems scary =) and you need expensive set of files and wht not ... how do i dip my toes into this? =)
Glad you liked it man. The nut files are the only real luthier tools you'll need the rest you can get from any hardware store. You used to be able to get single files of the gauges you want but looking around they don't seem to be sold like that now. I'd call a Luthier tool place and see if they can sort you out
@@Montysguitarsandpickups I looked around and you can get sets for whatever strings you use...so 10-46 for example. But I wonder about what to think of when you start on the nut/sadle ... Angles and depth and so on. Cus if you file away to much its not much to do...
@@mudfly3 Hey man sorry for the delayed reply. This is a tricky one but there are ways to fix it if you do go too low, I'll try and do a video specifically on that very soon.
@@Montysguitarsandpickups Hey man, thanks alot, that would be awesome. I´m guessing that fix would be the superglue/bakingsoda trick ? ?
@@mudfly3 A pleasure. Yeah that's one of the best ways.
Please make bass products also : ]
We have some more bass things arriving very soon
@@Montysguitarsandpickups thanks for replying Monty, that sounds amazing, please let me know if you plan on doing pickups and also what products work best on dark ebony bass wood : ] love the channel
6 machine heads away sound like an awful lot of turns! Is it so the strings get lower on the post giving you a sharper break angle over the nut?
Yes exactly, it takes a little longer to stretch in but its worth it
Wolf School. 👍
Happy to help
Matt, would putting a tiny amount of Petroleum Jelly on the screws have the same effect?
Yes exactly, you can use soap too
@@Montysguitarsandpickups awesome, thanks.
🙏🏻
Did you cover the pickups when rounding the fret ends?
I don't do usually
@@Montysguitarsandpickups -be super careful. Tape them up and vacuum particles carefully after you finish. A small particle can finds its way into your pickups and destroy them.
@@GIBKEL thanks for the tip
How do you clean a finished maple fretboard?
The best way is with lighter fluid and a toothbrush. That will get rid of any stubborn grime. If it is a lacquered board I would polish it with Muc-Off miracle shine, if it is an unlacquered board you Instrument Food or something similar.
@@Montysguitarsandpickups Thanks. Just ordered a can of Muc Off. I’ll use it on my bicycle, too. 😎👍🏼
What brand of nut files are you using?
Hosco
Absolutely brilliant .... love watching your videos on insta and on here !
I have a Jimmy Page Tele and now I have seen this I'm wondering if it would be possible to send my jp tele to you for the brilliant upgrade service you have just performed lol ???
Also what kind of price would we be talking ?
All the best Matty .
Hey dear chap, glad you liked the video. I can gladly help you out with that. For getting booked in and costings etc email mail@montysguitars.com and the lovely George can fill you in with availability and all the info. Cheers Matt
@@Montysguitarsandpickups Thank you so much Matt , I really appreciate it I will get on to this soon as I get the chance and the dosh ... Thank you again buddy
ps... it was me that asked you on insta about re-stringing my Ibanez RG to the E-BALL size 8 but I haven't got a clue how to reset the tremolo :) lol ..
thank you
ASH
@@ashleysidddons784 Well I'll get a video sorted for that then man!! Just got to get my hands on a guitar with a floyd
It's a little depressing that for a $1600 guitar you had to go through the trouble of dressing frets and fixing the action. Great video on the process though!!
1650 now
Who the hell rubs polishing compound onto frets without masking the board?
Most of the guitar techs I know. I doesn't damage the wood and gets removed with the lighter fluid / remoisterising process.
Why not remove the strings the way most roadie guitar techs do: just cut them off? Saves having to use a drill before snipping them off anyway to pass through the ferrules.
it's about trauma Jefferson . Releasing tensile tension all at once can store unnecessary compensatory tension aberration for posterity. Physics of wood fibers is interesting. Study recurve bows.
Cool video but please invest in some microphone for better audio. Cheers
Done
@@Montysguitarsandpickups It's All about sound and audio right? :) You can make a microphone like you do pickups... very good pickups. Same thing different name. Ok I'll stop ;) Thanks for the video!
@@Lorak669 tbh i did have a mic on when we recorded this but the card messed up