[Review] Atomic AMZ 1/27 4WD RC Car

Поделиться
HTML-код
  • Опубликовано: 22 июл 2024
  • Full analysis and building guide of the car that gave Mini-Z a boot up the proverbial, Atomic AMZ.
    CC subtitles available for English, Thai.
    Links for cars and pars are down below.
    First test drive video: • Atomic AMZ Drift - 1st...
    Manual: www.rcatomic.com/atomic/egr_ma...
    Car
    Chassis with electronics: www.miracle-mart.com/store/ind...
    Chassis with ESC: www.miracle-mart.com/store/ind...
    Chassis only: www.miracle-mart.com/store/ind...
    Shims for diff. : www.miracle-mart.com/store/ind...
    Hyper steering bell crank upgrade: www.miracle-mart.com/store/ind...
    Body post kit for lexan body: www.miracle-mart.com/store/ind...
    Lexan bodies: www.miracle-mart.com/store/ind...
    The soft body I show in this video is from Mini-Q: bit.ly/2MIiB4k
    The bodies in miracle mart are out of stock constantly. However you can check out www.markaracing.com/ because they make soft bodies too. They also make truck body. www.minizracing.it/minizshop/i...
    Also check out Kenonhobby, if you are outside US the shipping can get really expensive though. www.kenonhobby.com/search.asp?...
    Wheel, Mini-z AWD wheels the whole set: bit.ly/2VeVZsc
    1.5mm offset narrow wheel: bit.ly/2WSecRf
    0mm offset wide wheel: bit.ly/2znzs3K
    Tyres, Narrow: bit.ly/2U1oxXf
    Tyres, Wide: bit.ly/2NvknFB
    Battery: bit.ly/340Liik
    Battery Plug (ESC side) JST-PH 2.0: goo.gl/69G4zW
    Battery Plug (battery side) JST-XH 2.5: bit.ly/3bj4eM6
    Receiver Plug JST-XH 1.5: goo.gl/Mhy8pV
    Wheel nuts: bit.ly/2Lck02G
    Budget Radio Radiolink RC4GS: bit.ly/2WSjb0G
    What I actually use, Flysky Noble NB4: bit.ly/2FVvIdy
    The radio I use in this video is Futaba with FrSky module and the receiver you see in this video is FrSky D8 Mini just because it looks good: bit.ly/2L5TlSx
    WLtoys 1/28 K989 Touring Car: bit.ly/2Vr4fWQ
    WLtoys 1/28 K969 Drift Car: bit.ly/2znqnbb
    Mini-Q TRQ1 Drift Car: bit.ly/2HjQFQC
    You can help supporting this channel by purchasing from Banggood with these afffiliate links above.
    The price will be the same, all discounts and promotions are applied as normal.
    #AMZ #MiniZ #Drift
  • ХоббиХобби

Комментарии • 470

  • @BeaversHobby
    @BeaversHobby  4 года назад +16

    Time stamps
    Packages Pricing and requirements: 0:26
    Chassis: 2:15
    Electronics: 5:24
    Building & Tips: 6:34
    Fixing Problems: 8:17
    Final verdict & conclusion: 10:22

    • @driftzone5586
      @driftzone5586 4 года назад

      Beaver's Hobby what’s the difference between the amz and the amr can’t seem to find any info on the amr

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@driftzone5586 AMZ is all wheel drive, AMR is rear wheel drive.

    • @driftzone5586
      @driftzone5586 4 года назад +1

      Beaver's Hobby so would yo say amr and the drz are on the same level which would you say is better as I’ve heard nothing about amr and would like to hear more about it

    • @BeaversHobby
      @BeaversHobby  4 года назад +2

      @@driftzone5586 DRZ is based on AMR. Basically DRZ is AMR drift mod. I also have review for DRZ too if you are interested. They are RWD cars with fully adjustable double wishbone suspension.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @SuPreme OpZ No, you'll have to buy them all separately including wheels. This is kit car so it'll come with chassis and some electronics if you choose the package with ESC, servo and motor as I said in the video.

  • @maxrc8364
    @maxrc8364 4 года назад +5

    OMG, I am sold ! I have been eyeing the Atomic line up for a while. Now I MUST have one 🚘

    • @daej312
      @daej312 4 года назад +1

      MAX RC buy mine, I’m putting it on eBay tomorrow.

    • @maxrc8364
      @maxrc8364 4 года назад +1

      @@daej312 send me a link, I will see what I can do.

  • @wearemany73
    @wearemany73 4 года назад +10

    I love these videos, you’re always very precise and logical with your technical information. I bought the k958 from Banggood because of your videos. Banggood should give you commission.

    • @BeaversHobby
      @BeaversHobby  4 года назад +9

      I got some small commission when people buy from my affiliate links in the description. But as long as you have fun without spending a fortune that's good enough for me.

  • @LenierEusoj
    @LenierEusoj 4 года назад +5

    Nice!! Now im more eager to mess around with both my amz! I have those 2, one amr, and one drz! In my opinion, all are great! Thanks for this vid!

  • @user-ob1ob3xk1t
    @user-ob1ob3xk1t 4 года назад +4

    นำเสนอได้ดีมากครับ
    ข้อเสียข้อดีมีหมด
    ตั้งแต่ประกอบเปรียบเทียบให้ดู
    โอ้โห!!!ผมไม่รู้ว่าจะพูดยังกับพี่
    คลิปนี่ใครดูเนี้ยรู้เรื่องเลย
    ป.ล.(อ่านทุกคอมเมนตเช็คทุกคำตอบคนนี้ของจริง)

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      ขอบคุณมาก ๆ ครับ

  • @rc3151
    @rc3151 4 года назад +1

    Love your videos thanks for making this!
    Well done, nice job.

  • @seokidiecast6131
    @seokidiecast6131 4 года назад +3

    Fanatics video! I can't wait to see your next video!👀

  • @timzchannel1960
    @timzchannel1960 4 года назад +2

    Yo..! one of the best mini drift videos I have seen. Awesome!

    • @driftzone5586
      @driftzone5586 4 года назад

      timZ Channel when are we getting any updates on your channel that’s what got me started with mini z

  • @smugglersrun7779
    @smugglersrun7779 4 года назад +2

    Thanks Beaver great vid just finished my Atomic SZ build had same issue with the diffs being tight but now they broke in . Hope to see a video on the higher end Atomic cars

  • @GarageMiniRCUK
    @GarageMiniRCUK 4 года назад +10

    Great review. I think it works best at 94mm wheelbase. I use it for a cross between touring and drift racing. It's just as Beaver says, very predictable.

  • @bobtierney6946
    @bobtierney6946 4 года назад +3

    Thank you so much for your RUclips programs. I love Mini Z'S and the 1/28-1/27th cars spawn my them. From the MR01 introduction (while I was working at a hobby shop) I thought great cars that cost too much for it's market.
    You need to have cheap fun cars first. Get people interested in the fun. Give them fun reliable, cheap and quick.
    Their competitive side will drive the precise, close-tolerance of highly competitive chassis designs (expensive).
    I want to start my own club with a low-cost, entry level spec class of RTR 1/28th or even 1/18th cars. Get them Hooked on the Fun First. ALL the rest will follow.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Exactly! Now that the price has gone down micro RC (actually RC in general) has become much more accessible. People can try if this hobby is right for them and move to better car or leave it without big hole in their pocket.
      AMZ is really good for club racing because the spare parts are mostly easy to find.
      WLtoys K989 is another one that is much cheaper to start and has spare parts. However the stock radio is not that good and might leave a bad impression on someone who just started the hobby.

  • @NeoIsrafil
    @NeoIsrafil 3 года назад +2

    Omg, this is great! I've been wanting to change my k989 over to something because its so imprecise, and I use it as a loaner car to drive against me at home, and this would be the perfect cheap solution! I can just get the chassis and transfer all the electronics ive put into the 989 over to the amz! I've also got some spare motors from my mini z I might swap in to keep it all equal.

  • @zhuyufan1186
    @zhuyufan1186 4 года назад +2

    I just finished mine two days ago. I run into the same problem in gear mesh, but I follow the advice on the rctech which used double-sided tape stuck onto the aluminum motor mount and give the mount more grip. Also, the servo saver is useless and I had to use a servo horn instead. The other problems includes uneven toe angle (This is a lot of toe-in for the rear. But eyeballing maybe inaccurate), and kyosho's body clip touching the motor. But I am very fortunately that there is no missing parts, bindy suspension or overtightened diff from the factory. For the price, even counting in your own electronic, it is well below kyosho's AWD offering yet should be able to outperfom it on track.
    With all that said, I hope ATM understands the importance of quality control. Some people have just received BZ3 which is still missing parts. We are talking about a company which is making maybe fifth or sixth kits, not the first one (AMZ). If they wish to reach a wider customer base, the quality control and plastic parts needs some serious work. Also I notice the kit's content seems to different from batch to batch, In your kit you have the adjustable front toe link and 1.5 camber upper arm. Mine has fixed toe link and 1 camber upper arm.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Atomic does have quality control issue. My DRZ got a ball link without screw thread and a lot of misalignment. The car was $200 and I was shocked. I'm so happy this kit doesn't have anything missing and everything fits together perfectly.

  • @Rizzzzzzzzzzzzzzzzzzzzzzzzzz
    @Rizzzzzzzzzzzzzzzzzzzzzzzzzz 4 года назад +1

    I got this one because of you! Kyosho Subaru BRZ body

  • @adriancjones
    @adriancjones 4 года назад +1

    Hey Beaver. I built an atomic amz 2wd. I’m having a difficult time keeping it going straight. It’s not a drift car so I am using regularly rubber tires. I have to apply power very slowly or it will turn 180 degrees. I have adjusted my steering rate lower, but with the slightest movement it turns 180. Is it potentially a differential problem? Too lose or too tight?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      There are some thing you can do starting from toe angle, a bit of toe out will help you go straight easier. Next, the tyres: use less grip at the front. For example 30 degree front narrow and 20 degree rear wide. Also the suspersion: make front harder than rear so the rear has more grip.

  • @nswiss19751
    @nswiss19751 3 года назад +1

    I love this channel ❤

  • @kristofercerny3825
    @kristofercerny3825 3 года назад +2

    Hi Beaver! I have a question. So I have a wltoys k989 that broke the first day I got it from a drop. Does all of those electronics fit in this chassis without replacing them?

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      Yes, it does. But for the servo if your Wltoys has one mounting arm because the other side is cut then you'll either have to stick it down with double-sided tape or get a new servo.

  • @user-fd8nl2kf9q
    @user-fd8nl2kf9q 4 года назад +4

    Hi, i just bought this kit after looking of your video. One quastion: to drift, shell I lock the diffs?

    • @BeaversHobby
      @BeaversHobby  4 года назад +7

      Yes, you can just lock the original diffs to drift. They're ball differential so you just tighten them and they will be locked diff. Also change the front to one way if you like.

  • @YonkoIan
    @YonkoIan 4 года назад +2

    Very nice I might try to save for the atomic drz and all the components

    • @foxracerdrew
      @foxracerdrew 4 года назад +3

      Would highly recommend getting your hands on the metal front bulkhead with bearing mounted sliding rack, the plastic one continuously comes loose.

  • @322816
    @322816 4 года назад +3

    Great review, thanks. Do the WLToys wheels fit on the AMZ?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Yes, they are the same Mini-Z AWD type.

  • @brandonragsdale6219
    @brandonragsdale6219 3 года назад +2

    Hey I love your channel great information, since the most all cars mimic the mini z and the mini is always sold out. Which do your recommend wpl or atomic or do you think a different chassis is better

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      GL Racing is the best manufacture right now. Think of it as an upgraded Atomic. If you want an AWD car then get either Atomic AMZ or GL Racing GLA.

  • @mist3rp777
    @mist3rp777 2 года назад

    Hi i have watched your video and I am planning to do the same could you give a link for all the hardshell bodies that fit the car 🚗?

  • @adriancjones
    @adriancjones 4 года назад +1

    Hey Mr beaver. Do you know of another source to get lipo battery from. Banggood never gets here to the US and miracle mart is always out of stock.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      I'm not sure if hobbyking.com still has Lipo in US warehouse but it's worth a look. Check out SupergDrift supergdrift.com/store/product-category/1-27-scale-mini-z-drz/
      and www.kenonhobby.com/ .
      Other shops that sell micro drone parts should have 2S 300-400mAh battery too.

  • @BMR3
    @BMR3 4 года назад +3

    Great video, I think you convinced me to get one in the future so I can build a drift car with Lexan semi truck body. It looks like a good car but I wouldn’t call it a mini-z killer simply due to the batteries. I love that the mini-z can use disposable batteries and I’m not forced to carry a charger.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Convenient for transporting is also the reason I'm still taking Firelap IW04 with me on holidays so I don't have to carry an extra charger and transporting fragile battery.
      Lipo can be charged within 1 hour without slowly destroying the battery though. That's why RC is moving away from NiMh.
      Anyway, I'm still waiting for NB4 receiver for Mini-Z EVO to be available so I can get MA030 EVO.

    • @BMR3
      @BMR3 4 года назад +2

      Beaver's Hobby nice! Yep I’m planning on getting the MA-030 soon so I can start a series on that car as well. The MA-030 looks awesome, but I hope release a MA-030evo PRO around the holidays so I can get that.

    • @BMR3
      @BMR3 4 года назад +1

      Can you make a video about the NB4? Like a review & talking about the features. Im not very aware of this controller

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@BMR3 It's in the pipeline.

    • @BMR3
      @BMR3 4 года назад

      Beaver's Hobby you are awesome man!!! Quick question, would the NB4 be able to talk with a MA-020s frequency? The NB4 looks amazing, but I think I need a KT-432pt so I could run both cars.

  • @310smoker
    @310smoker 4 года назад +1

    thats cool , I own a 350z
    so i purchased the HPI sprint 2

  • @santogo
    @santogo 4 года назад +1

    Hi Beaver, i bought this kit too. Where did you get the front one way and rear solid axel ? Nice vid. Thanks

    • @BeaversHobby
      @BeaversHobby  4 года назад

      I use one way from Sinohobby Mini-Q but I suggest Eagle Racing because the crown gear is better. www.ebay.com/itm/MA20VE-23-AL-Front-One-Way-For-AWD-MA-020VE/253618039700
      And rear solid. www.ebay.com/itm/MA20VE-13-AL-Rear-Solid-Axle-For-AWD-MA-020VE/253336924294
      Don't forget the shims. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=83_1066&products_id=6103

  • @BlitzWorks
    @BlitzWorks 4 года назад +4

    Any plans to review the higher end atomics such as the SZ ground force of the BZ3? given the SZ takes the same diffs this one may be better for drifting

    • @BeaversHobby
      @BeaversHobby  4 года назад +2

      Talked with people who got SZ and it seems like the chassis is plagued with problems. I might get the GLA v2 instead if I can't find Mini-Z MA030 EVO + NB4 receiver in Europe or it goes out of stock once I have money.

    • @BMR3
      @BMR3 4 года назад +2

      Beaver's Hobby I would love to see your opinion on the GLA car, I don’t know much about it so one of your videos would be golden.

  • @vektr6278
    @vektr6278 4 года назад

    Do you have an idea on how to make the AMZ a good cs car

  • @xgeo88
    @xgeo88 4 года назад +1

    Thanks for this video. Is there a way to increase the steering angle for amz?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      The best way is to use hyper steering bell crank upgrade like I did. If you can't find it (or it's out of stock and you don't want to wait) you can use slimmer tie rod that connects between left and right hubs. It will allow the car to steer a bit more. Original rod is very thick.

  • @ST1VO
    @ST1VO 4 года назад +1

    Hi Beaver, do you know any 1/28 chassis that will fit 90mm mini z body?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      There are quite a few chassis.
      Mini-Q Q2 for RWD touring. It's the same as Mini-Z MR02 (especially now that they sell it with front wide chassis). You only need to change the motor mount, again, like Mini-Z. ruclips.net/video/i9iXnSLetkg/видео.html
      HGD1 for RWD drifting. ruclips.net/video/_c-3Nqis7gs/видео.html
      GL Racing GLA also has 90mm version in narrow so it's like MA010/020 out of the box regarding width.
      AMZ, you'll need to find 90mm parts but they exists.
      Mini-Q Q7 with 90mm spur gear will fit but not the narrow body, this chassis is equivalent to wide so your body has to have some wheel offset, not 0mm offset.

  • @mrmoravian
    @mrmoravian 4 года назад +1

    Hey I just finished one today.my rear suspension don't move at all.you think I tightened them down to much.1st build

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Remove the knuckle and see if the arms can move up and down freely. If not, there is excess plastic on the arms. Look for seem lines and clean them out. But if they can move then problem is at the ball link. I did it at 9:06 .

  • @AstroBananna
    @AstroBananna Год назад +1

    Is there somewhere i can get the full kit with the recommended upgrades included for extra all in one neat package? Do you have a store you cant put the parts together into a mega kit?

    • @BeaversHobby
      @BeaversHobby  Год назад

      Links are in the description. Unfortunately they don't bundle the steering upgrade with the kit so you'll have to buy that separately.
      The wheels depends on the body you choose. Nowadays you will have the wheels with the body so that's nothing to worry about.
      As for the shop it depends on where you are, if you are in the US you can contact WolframRC www.wolframrc.com/ or micro rc syndicate www.microrcsyndicate.com/ and ask them if they can setup a complete package for you.

  • @GAMEOVER-RACING
    @GAMEOVER-RACING 2 года назад +1

    Very nice I just got myself one 👌👍

  • @adriancjones
    @adriancjones 4 года назад +1

    I just finished building this car. It was fun to build, but I still have a few issues to sort out. The motor pinion gear is too tight and came off, so I will have to adjust the gear mesh. I am not sure on the differential shims that you showed in this video. What was the purpose? Also there is too much space between the wheel lock nut and the wheels, so I will have to correct that as well.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      The 6x8 shim on differential is to adjust the diff gear position (crown gear) to mesh with pinion gear on prop shaft correctly. Mostly it'll be too far and the gear will slip causing them to wear out prematurely or won't send power to the wheel.
      If you have problem at the wheels then you'll need 3.1x4.5 shim to fix the fitment of the wheel shaft.
      ppm-rcracing.com/products/3.1-x-4.5mm-Stainless-Steel-Shim-Set-%280.1%2C-0.2%2C-0.3mm-10%7B47%7Dea%29.html
      Also 3x5 from Atomic www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1020_1023&products_id=13815

  • @rc-fannl7364
    @rc-fannl7364 4 года назад +1

    Is this new? I remember getting an RTF (minus body) years ago? Or did they re-release it as kit?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Yes, it's new. They are still making it but not the RTR version.
      Some upgrade parts seem to be out of production though like the aluminium bulkhead. But this car and basic spares are still on going.

  • @scottsrcshop
    @scottsrcshop 2 года назад +1

    Hey beaver! Could you please recommend to me a good 1/28 scale car for a small / medium sized basement carpet track. No idea which model to choose. I already have a atomic drz so I don’t care if it’s not good for drifting.

    • @BeaversHobby
      @BeaversHobby  2 года назад

      For drifting, keep using the DRZ or DRZ V2, it's already good. For touring if you want a RWD touring then take a look at Atomic MRZ or GL Racing GLR GT. As for AWD touring take a look at GL Racing GLA V2.1.
      In budget category, take a look at Mini-Q Q2 or MRC. It's RWD comparable to Mini-Z RWD but much cheaper.

  • @marresechsundachtzig86
    @marresechsundachtzig86 4 года назад +2

    Regarding the Problem with the Servo saver arm: what i did was stripping the screw off its thread with some pliers. About 3mm at the tip. Just enough that it fits in the hole of the Servo shaft. Because the screw the manual tells me to use clearly doesnt fit. Now you can push the Servo saver arm easily on to the Servo shaft.

  • @vapo8627
    @vapo8627 2 года назад +1

    Hi,Beaver! I see description of video but I don't find which type of connector Atomic servo? Thanks a lot for your videos!!!

    • @BeaversHobby
      @BeaversHobby  2 года назад

      The Atomic servo uses JST-ZH 1.5mm 3 pin plug.
      It's the common plug for 1/28 racing cars so you can get a bag of it to convert your electronics and receiver.

    • @vapo8627
      @vapo8627 2 года назад

      @@BeaversHobby thanks 👍

  • @JimmyCNguyen
    @JimmyCNguyen 3 года назад +1

    I finally finished building my first one. Ran into an issue, not sure why my gear is so stiff. I replaced the front one way and ridged rear with mini q’s but they seemed to fit well so not sure where it went wrong.

    • @BeaversHobby
      @BeaversHobby  3 года назад

      Check the gear mesh on both front and rear gearboxes first. You might have to shim them especially the front one way if the gear doesn't meet the pinion. Put it together without motor first and see if it's still smooth and can roll easily. If not you'll have too loosen the gearboxes and move them around so they line up properly. Then move on to the motor. Setting gear mesh there is a bit difficult but slowly screwing it in and keep checking the smoothness will do just fine.

    • @JimmyCNguyen
      @JimmyCNguyen 3 года назад

      @@BeaversHobby That was it! thank you! i regret not checking youtube for your answer before trying it myself....i broke one of the wheel shaft in the process haha...noob mistake. Now to wait for a month for the replacement parts....so far fun, i'm enjoying the process of it all. Thanks for your videos, got me into it lol

  • @galactic-brickproductions3143
    @galactic-brickproductions3143 Год назад +1

    im looking inta buying this chassis, the problem is due to some money problems i have to try and build the car as cheap as possible. i probably have a battery that fits and i have a transmitter en reciever that might work but i dont have that type of motor and i have a mini servo but idk if that works. can u send me a link to a place or links for individual parts like the motor etc?

    • @BeaversHobby
      @BeaversHobby  Год назад

      Understood. I have worked out the most economical way of building this chassis.
      First, get the chassis with ESC. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_1037_1040&products_id=13055 It'll be $14 more than bare chassis but this ESC is better than anything up to $40.
      The motor, Surpass Rocket either 3500KV or 5500KV. www.aliexpress.com/item/1005002537463848.html
      Servo, pretty much any 5g will fit but AGF/AFRC has the best price-performance right now. www.aliexpress.com/item/1005001867780985.html
      This will be $123.6 exclude shopping so you'll save a bit from the $142.9 for kit with electronics from Atomic.

  • @wazfpv2069
    @wazfpv2069 4 года назад +1

    nice nice nice I just ordered the full version ^^ but Hyper steering bell crank upgrade is out of stock

  • @enlightenphotography7199
    @enlightenphotography7199 4 года назад +2

    Hello beaver, is there any system like atomic hyper steering bell crank that can be apply on mini z awd? Thanks before.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Unfortunately, no. Mini-Z is very restricted when it comes to steering upgrade.

    • @enlightenphotography7199
      @enlightenphotography7199 4 года назад +1

      Too bad.. okay then, thank you for your reply.

    • @xgeo88
      @xgeo88 4 года назад

      Beaver's Hobby this is what I hate on mini z. They are marketing their awd as drift machine but option to increase steering angle is a NO.

  • @leon0247
    @leon0247 4 года назад +1

    Nicee build sweet video

  • @ArdiNugrohocilacap
    @ArdiNugrohocilacap 4 года назад +1

    Great,, thx for detail

  • @gabrielsylar7
    @gabrielsylar7 4 года назад +1

    Are you planning to do video for fine tuning or how to maintain amz type for touring.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      I'll do one update for my 50:50 drift full setup (yes, this will be fine tuning). After that I'll try to make the CS mod and then we'll see. I don't know if I'll keep it as drift car or turn back to touring. I really like how it drifts though.

  • @adriancjones
    @adriancjones 4 года назад +1

    hey Beaver, im having a tough time getting the differentials not to slip. I think if I try and tighten too much then im going to strip out the plastic gear. Do you have a solution? Maybe a metal gear?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Metal gear will increase the weight and chew the pinion. Where do you get the slip? Is it slip between gear or slip because the crown gear on the diff spinning without sending power to wheels?
      If it's problem between pinion and diff then you'll have to shim it with 6x8mm shims. If the gear mesh is good but it doesn't send power to the wheels then you have stripped nut in the diff.
      Anyway, change the plastic nut to lock nut regardless because it'll strip sooner or later.

    • @adriancjones
      @adriancjones 4 года назад +1

      Beaver's Hobby, the pinion was too loose so no power to the wheels. I tightened the plastic nut and it is stripped out. I found that the colored wheel lock nuts fit, and also provide an added non slip feature so I am using two of those to tighten the diff. So far so good.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@adriancjones So I guess the slip was within the diff. Yes, use coloured wheel nut in it will fix the problem.

  • @ninjaarcades7356
    @ninjaarcades7356 4 года назад +1

    Good video

  • @Penafort
    @Penafort 3 года назад +1

    Were can I find and buy a complete kit to be delivered in Europe / Portugal?

    • @BeaversHobby
      @BeaversHobby  3 года назад

      Check out. www.srcc-devils.de/
      Here it is. www.srcc-devils.de/ATOMIC/AMZ001-EXKT-ATOMIC-AMZ-4WD-Chassis-1-27-Mini-4WD-Touring-Car-mit-Motor-.htm?a=article&ProdNr=280343&p=1002

  • @Motofoko
    @Motofoko Год назад +1

    hi , just a quick question , my amz wont go reverse , only foward....how to disable racing mode ? i dont have program card

    • @BeaversHobby
      @BeaversHobby  Год назад +1

      You can hold the button to program it like EZrun. Here's the manual. www.hobbywing.com/products/enpdf/EzRun60A.pdf
      However the program is different. Here's program table. imgur.com/AwBHACd

    • @Motofoko
      @Motofoko Год назад +1

      @@BeaversHobby thanks mate :D I will give it a try

  • @euqat
    @euqat 4 года назад +1

    Hi BH, what would be your go-to 1/28 4wd car for drifting inside? This one looks nice but requires some modifications, are there better alternatives for drifting, using Lipo batteries as well? Thanks for your content man

    • @BeaversHobby
      @BeaversHobby  4 года назад

      My 2 favourite 4wd cars are this one and Mini-Q Q7 ruclips.net/video/kCjglUnXBQU/видео.html .
      Newer Q7 needs universal drive shafts (CVD) upgrade, just put the metal drive shafts in and it'll be perfect.

    • @euqat
      @euqat 4 года назад +1

      @@BeaversHobby The Q7 seems to be exactly what I need. Thanks for the help mate.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@euqat My pleasure.

  • @Weaselpro
    @Weaselpro 4 года назад +1

    Hi, looking your video, I want to order amz from Miracle Mart. But I am new to this mini z staff. So could you please recomed, which rims+tires for drifting I should order together to fit to most mini-z bodyes later on? I totaly lost in off-sets. And there also rims for TRQ1 on the MM, but they specifyed as front and rear. What is the difference? Do they fit to amz? Thnx in advance.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      AMZ uses Mini-Z AWD wheels. There's specific category in MM website.
      You'll have to choose the wheels according to the body because the offset has to go together with body's width. One of the best drift bodies is what I use, Nissan Skyline R32, the wheel offset for this body is 1.5mm offset narrow wheel. So you need 4 for all corners.
      Another good body is Toyota GT86/Subaru BRZ which needs 1.5mm offset as well. Next is Skyline R33, if you get the Nismo version it will come with the wheels. Basically, any body with 1-1.5mm offset narrow wheels are good for drifting with varying degree of control. All in all, 2 best choices are R32 and GT86. Other might suggest different bodies but these are my personal preferences.
      Drift tyres are included with the car and they are very good so don't worry about that. If you want different tyres, look for DS Racing and Mini-Z tyres. Tyres from Aliexpress will work but not as good so I suggest sticking with Atomic, Mini-Z and DS Racing.
      AMZ also uses same offset as Mini-Z (they are the same width) so you can swap between 2 cars without changing anything. Although I doubt you would go back to Mini-Z after experiencing AMZ.
      TRQ1 wheels are also in Mini-Z AWD format so the wheels are the same as AMZ.
      I forgot to answer front and rear wheel question.
      Front wheel is narrow. Rear wheel is wide. If I say narrow wheels on all corner then it means get 2 sets of front wheels. You'll get 4 narrow wheels from that.

    • @Weaselpro
      @Weaselpro 4 года назад +1

      @@BeaversHobby Many thanx for prompt answer. So these rims should fit? www.miracle-mart.com/store/index.php?main_page=product_info&products_id=12068

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@Weaselpro This is 2.5mm offset. The wheels might stick out or rub the arches. Look for 1.5.
      Here they are. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1020_1059_1077&products_id=904

    • @Weaselpro
      @Weaselpro 4 года назад

      @@BeaversHobby Thnx. One more quastion. Can I fit these iwaver bodies to amz? www.miracle-mart.com/store/index.php?main_page=index&cPath=67_74_1045_82

  • @nicogeek2639
    @nicogeek2639 4 года назад +1

    Hello, I am doubting between the AMZ and the SZ. The total set savings is 60 dollars cheaper the AMZ. What would you buy? Thank you

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      SZ has better handling but from what I gathered it has some problems like the front CVD keep breaking, broken rear part (need aluminium upgrade), some grinding at the rear gearbox and it's a bit more difficult to maintain from separated centre shaft.
      Also wheelbase is not adjustable. That's the main reason I choose the AMZ over SZ. I wanted to build 94mm wheelbase drift car.
      For hi-end AWD take a look at GLA from GL Racing. So far I have not heard a horror story about it.

    • @mariadoreyes2014
      @mariadoreyes2014 4 года назад +1

      @@BeaversHobby hi,i´m Nicogeek ,
      Thank you very much. The reason to think about the sz is for the low price of acquisition 150 usd shipping included
      the gla is much more expensive
      My use is going to be races, no drift.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@mariadoreyes2014 RCmart, right? At 150 it's so tempting. Touring performance is definitely better than AMZ. If it'd get for touring I'd buy SZ too. Just shim the rear gearbox and it should be OK. Also apply for e-mail notification for this part. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1162&products_id=14129
      I've heard it's the one that plastic part will break. So aluminium is a must.
      For the front CVD, if original break try using Aurora. ppm-rcracing.com/products/Wide-Crooked-Angle-Universal-Shaft-for-Mini%252dZ-%286061-Black-1-Pair-Long%29.html
      Hope this helps.

  • @IBangkneeBakks
    @IBangkneeBakks 4 года назад

    please add links for Shims

  • @jesseco9964
    @jesseco9964 3 года назад +1

    So bought an adapter to use a standard receiver and it won’t power on.
    Help please.

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      Check the plug orientation if you plug it in the right side. Also if you have a multimeter, check if the adapter is ok and doesn't have any break in the wires.

  • @kristofercerny3825
    @kristofercerny3825 4 года назад +1

    I have a question. How do I install drift tires (mdt001) onto mini z wheels?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Simply push it in. You'll see the small indentation step on the tyre, that side goes on to the wheel. It will fit together perfectly with the knurling on the inside of the wheel.

    • @kristofercerny3825
      @kristofercerny3825 4 года назад +1

      Thank you so much for your help. Now I'm just waiting on the trqi with gyro and one way differential from Bangood

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@kristofercerny3825 My pleasure. If you want to remove the tyres from TRQ1 wheels you can dip them in warm water then push the tyres out.

  • @adriancjones
    @adriancjones 4 года назад +1

    Do you know what mini-z bodies will fit on this chassis?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Any 94mm and 98mm body. If it's narrow it'd better use 1.5mm offset so the servo fits on the side. This problem can be solved easily if you glue the servo down and cut the arm off. Then you can use any narrow body.

  • @ekimusman2
    @ekimusman2 3 года назад +1

    great video! consdering getting into 1/27 scale to run in my basement.

  • @cityofplant
    @cityofplant 3 года назад +1

    Do you still recommend this chasis to house wltoys k989 electronics for drifting? I found a good deal at my local hobby shop.

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      Yes, I do. It's a much better chassis than WLtoys even with the same brushed electronics.

    • @cityofplant
      @cityofplant 3 года назад +1

      @@BeaversHobby welp, turns out my local hobby shop doesnt have them in stock. Even their main website doesn’t have them in stock. I guess its just my luck.

    • @BeaversHobby
      @BeaversHobby  3 года назад

      @@cityofplant Their restock date is so random that if you find one, just buy it. If one then wait. Check their websites regularly or just ask the shop to put you on alert when it's back.

  • @loosezenpin
    @loosezenpin 4 года назад +1

    Great video I got my car today but I cant figure out the electronics. I'm using a radio link transmitter and reciever with adapters for the servo and esc. The reciever connects to the transmitter but the esc wont. Can you guys help me

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Are you sure the adapters are working correctly? Does it got power? Does the steering work? If the steering work then there's power and you'll only have to figure out the ESC. Try calibrating the ESC by holding the button and turn it on, then release the button, it'll go in to calibration mode. Now press button on the ESC once to register mid-point, fully press the throttle then press the ESC again to register full throttle, next brake and press the ESC. Wait for a bit and it will start.

    • @loosezenpin
      @loosezenpin 4 года назад

      @@BeaversHobby yes the steering does. I fixed the polarities on the adapters and every thing is binding g and getting power. My only problem now is that I tried to do the calibration steps and there is no blinking when I press the button. Do you know what the problem might be

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@loosezenpin Try reversing the channel 2 (throttle) on the transmitter. That might help in some case. But if you can't calibrate but it still works then you probably don't have to do it.

    • @loosezenpin
      @loosezenpin 4 года назад +1

      @@BeaversHobby man thanks that was the problem. I put both on the first 2 channels and everything works flawlessly. Thank you so much and keep up the great videos

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@loosezenpin Glad everything works now. Have fun!

  • @amiraseri
    @amiraseri 4 года назад +1

    Awesome. Can I buy the readily installed from you?

  • @gda882002
    @gda882002 3 года назад +1

    i love your videos , what style of connecter should i be looking for the battery and where do you buy your batteries

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      If you want direct connection, the plug is JST-PH 2.0mm 3 pin. There're Atomic batteries with direct PH plug but they are a bit hard to find. You can buy any 300-400mAh 2S lipo and make a converter from JST-XH 2.5mm to JST-PH. I use Giant Power bought from banggood while it still shipped to Europe, now they don't. bit.ly/340Liik
      Check out Hobbyking Turnigy as well. This one got direct plug. But you'll need an adapter to charge. hobbyking.com/en_us/turnigy-nano-tech-300mah-2s-35-70c-lipo-pack-e-flite-eflb2002s25-micro-series-compatible.html

    • @gda882002
      @gda882002 3 года назад +1

      Thank you so much for the reply and help

    • @BeaversHobby
      @BeaversHobby  3 года назад

      @@gda882002 My pleasure. Good luck with the project.

  • @MicroRCFiend
    @MicroRCFiend 2 года назад +1

    Can this be modded for more steering lock? Trying to use it with Dnano on small track but it's utterly useless turning circle just like the K989.

    • @BeaversHobby
      @BeaversHobby  2 года назад +1

      You can either make the lower tie rod with smaller head (3.5mm ball caps got a few to choose from) or use the hyper steering kit. It can only turn until the knuckle hit the gearbox. Wheelbase also helps. With 94mm wheelbase + hyper steering I got is around 37cm turning circle. Is that enough for Dnano track?

    • @MicroRCFiend
      @MicroRCFiend 2 года назад +1

      @@BeaversHobby Ok, I think that may be enough if this 'hyper steering kit' is still about to buy. This was the test fail although track is at my brothers so cannot measure right now.drive.google.com/file/d/1WDoJsVTSlrUGvlZGCPDjOVsGT0fRHdRN/view?usp=sharing

    • @BeaversHobby
      @BeaversHobby  2 года назад +1

      @@MicroRCFiend It's tight in places but I think hyper steering will do fine with it.

    • @MicroRCFiend
      @MicroRCFiend 2 года назад +1

      @@BeaversHobby Thanks, i'll give it a go before looking for for a replacement frame.

  • @Weaselpro
    @Weaselpro 4 года назад +4

    Hi, i got one and assembled. Drifts perfect. Could you pls recommend fixed differential for this car?

    • @BeaversHobby
      @BeaversHobby  4 года назад +2

      Eagle Racing solid axle is what I use. You can also use the included ball differentials and tighten them to lock.
      One way from Kyosho will need to grind the gearbox out a bit to fit. Mini-Q and Eagle Racing one way will fit directly. However Mini-Q one way has changed and now it got sharp gears that will chew the pinion.

    • @Weaselpro
      @Weaselpro 4 года назад

      @@BeaversHobby Hi and thanx. I cant find Eagle solid axles somehow. Does Kyosho solid axle the trick too? I meant does it fits? (rc.kyosho.com/en/mdw024.html) And they also have one way diff. (rc.kyosho.com/en/mdw017.html). Does it fit? I have tightened original diffs on AMZ but still I can move them by hand.
      And, many thanx for your pointing to AMZ, I am really exited how easily it drifts. Even without gyro. So I am selling my trq1 out cause after amz its feels as piece of crap. .

    • @Weaselpro
      @Weaselpro 4 года назад +1

      @@BeaversHobby One more question: somehow ESC on AMZ cuts off lipo at 7.6V instead of normal 6V. I cant to find any manuals how to adjust this cutoff.
      There no manual at all on Atomic site and on HW site. Could you advice please, how to set this cut off parameter?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@Weaselpro The Kyosho stuffs are a bit too thick as I said earlier so you'll have to grind the gearbox a bit to make them fit. However they are great quality and I highly recommend both one way and solid axle.
      As for the high cut-off. You'll have to find a Hobbywing programming card. The one for EZrun will work too. And set the menu 2 to change the cut-off voltage.
      1 = off
      2 = 2.6V/cell (5.2V)
      3 = 2.8V/cell (5.6V)
      4 = 3V/cell (6V)
      5 = 3.2V/cell (6.4V)
      6 = 3.4V/cell (6.8V)
      I highly recommend no. 5 to get 6.4V because 6V is a tad too low.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@Weaselpro I forgot to mention you can hold the button and set it like Hobbywing EZrun too. Try and find manual for EZrun and you'll see how to set with just the button on the ESC. Then go to menu 2 and did what I said earlier.

  • @GarageMiniRCUK
    @GarageMiniRCUK 4 года назад

    hi Mr B, what type of connector is on the atomic motor ?

  • @jesseco9964
    @jesseco9964 3 года назад +1

    How did you build the diffs? I’m having a hard time.

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      There's really no instruction but it's similar to other ball diffs. Check out the instruction from GL Racing. gl-racing.com/GLA/v2/guide/#ball_diffs

  • @z-collector7518
    @z-collector7518 4 года назад +1

    Thank you for the video. Lots of good information there.
    Any chance you will be reviewing the BZ3?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      There's a chance but don't hold your breath.
      I'm really thinking about it. I've always wanted a belt-driven car but I'm also afraid I don't have an optimal place to run it. Also BZ3 has quite weak steering system that one crash can cripple it which scares me even more. Still, if I'd but a belt, it will most likely be BZ3.

    • @z-collector7518
      @z-collector7518 4 года назад +1

      @@BeaversHobby From what I can see the bz3 has an improved, sturdier direction compared to previous versions but you are the expert, I accept your opinion. Cheers!

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@z-collector7518 From what I can tell the handling is brilliant. Just don't crash, that's all.

  • @JimmyCNguyen
    @JimmyCNguyen 3 года назад +1

    Hello For drifting, which front 1 way and ball differential would you suggest?

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      For AMZ 3Racing or Eagle Racing will fit without any mod. Both of which are hard to find and possibly aren't being made anymore. Mini-Q one way will also fit, the one is this video is also from Mini-Q but the newer batch has very sharp gear so it will destroy your centre shaft pinion. You can also use Mini-Z one way but you'll have to shave the gearbox a bit to make it fit. I'd say it's worth the hassle because it's the best.
      As for ball differential, stock ball differential is more than good enough. If you want an upgrade look for GLA light weight ball diff.

    • @JimmyCNguyen
      @JimmyCNguyen 3 года назад +1

      Beaver's Hobby thank you! Parts ordered can’t wait to install and give it a run.

    • @BeaversHobby
      @BeaversHobby  3 года назад

      @@JimmyCNguyen My pleasure. Good luck with the project.

  • @Facewizard13
    @Facewizard13 2 года назад +1

    Can you connect a spektrum receiver to this?

    • @BeaversHobby
      @BeaversHobby  2 года назад

      Yes, this is still the same 3 wire system just like any other RC. The only difference is the plug, it's JST-ZH 1.5mm instead of JR/Futaba plug you use in other scale. You can make JST to JR adapter or just convert the plug to JR to match your receiver. A word of warning though, Spektrum has quite big receivers so choose one that would be small enough to fit inside the body.

  • @santogo
    @santogo 4 года назад +1

    Hi Beaver Nice vid i just ordered one too. What about gyro ? Can we connect Kyosho’s awd gyro to the supplied esc ? Many thanks.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Edit: Sorry, I was looking at the wrong video. You can't use Mini-Z gyro with this. You'll need separated unit like this. www.ebay.com/itm/3944MINI-BK-SP-MINI-GYRO-AL-Case-BK/254103498486
      And trust me, it's miles better than Mini-Z unit.

  • @user-cs2ix9zz1m
    @user-cs2ix9zz1m 3 года назад +1

    Great video! I wish I could watch this video before buying & upgrading my K969...
    (Atomic was an option, but I chose Wltoys because of the wrong info from my friend that it can handle 4S NiMH)
    Btw, Can it use the 4S AAA size battery holder(51x22x22mm) by attaching it with velcro to the chassis?
    LiPos have great performance, but I have a fear of them...

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      About what battery you can use, it's all up to the electronics speed controller (ESC). WLtoys can handle more weight than the AMZ so I suggest you stick with what you already have.
      For the standard brushed motor you can use a cheap 20A ESC like this www.ebay.com/itm/20A-RC-ESC-Brush-Motor-Speed-Controller-with-Brake-For-RC-Car-Boat-Tank-Parts/143826111473 .
      As for a brushless motor you can use 4x NiMh with DasMikro (this one bit.ly/3h07teH ) and PN Racing ESC V2 with the terminals bridged (refer to the manual). You just need to change the ESC on your car and you'll be able to use it with 4x NiMh.
      Don't forget that you'll need a radio as well if you haven't got one already. Here's a guide to basic RC electronics and how to upgrade.
      ruclips.net/video/BSt7U-yOa4Q/видео.html

    • @user-cs2ix9zz1m
      @user-cs2ix9zz1m 3 года назад +1

      @@BeaversHobby Thanks for your advice and help. Merry Christmas and Happy new year!

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      @@user-cs2ix9zz1m My pleasure. Merry Christmas and Happy New Year to you too.

  • @Chardbull
    @Chardbull 2 года назад +1

    Do you recommend amz electronics or we should use another combo?

    • @BeaversHobby
      @BeaversHobby  2 года назад +1

      Yes, I recommend the kit with electronics. It's still one of the best sensorless kit.

  • @TriNitrate
    @TriNitrate Год назад

    turning circle is 60cm?
    what does that mean
    like at what speed what tire what friction?

    • @BeaversHobby
      @BeaversHobby  Год назад

      That means it needs 60cm to make a u-turn under maximum grip with lowest speed.

  • @benweddup552
    @benweddup552 4 года назад +1

    Hi beaver
    I just built my one but I forgot about changing diffs.!! Where do I get the diffs you mention for drifting.?
    Thanks again.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      I use one way from Sinohobby Mini-Q but I suggest Eagle Racing because the crown gear is better. www.ebay.com/itm/MA20VE-23-AL-Front-One-Way-For-AWD-MA-020VE/253618039700
      And rear solid. www.ebay.com/itm/MA20VE-13-AL-Rear-Solid-Axle-For-AWD-MA-020VE/253336924294
      Don't forget the shims. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=83_1066&products_id=6103

    • @benweddup552
      @benweddup552 4 года назад

      Hi again,
      Well I’ve fitted the new diffs,
      But I’ve had to order the different wishbones as the standard setup makes the driveshaft too long and locks up when trying to turn wheel or steering.?’
      All I can think is the new diffs are slightly longer...
      I’ve also ordered the 3500kv motor like yours as mine is for drifting.
      I’m using model kit bodies as I can’t find the shell I want ( ford escort mk1 or 2 )
      I’ve also ordered the ali upgrades too, but can’t seem to find the 98mm extension for the propshaft
      I need to bring the wheels in slightly, I need to bring them in by 2mm
      So do I look for -2mm wheels.?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@benweddup552 Very strange problems you've got there. The upper and lower arms shouldn't be that short. You should check if the bearings are fitted properly on the knuckles so the drive shaft won't stick in or out too much.
      The 98mm shaft should be in the kit. It's the longer one. There's no -2mm offset. The lowest offset you can get is 0.

    • @benweddup552
      @benweddup552 4 года назад

      Beaver's Hobby thanks,
      I’ve got the atomic 3500kv motor but can I use the flysky fs-gr3e receiver.? Or Do I need a esc in between motor & receiver.?
      Thanks again

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@benweddup552 Yes, you can use flysky receiver providing you use Flysky transmitter. And yes, you need to use ESC too. The RC electronics are like this battery connects to ESC. ESC provides power to motor and also power up receiver + servo.
      Servo connects to receiver.
      For more information about RC electronics you can watch this video. ruclips.net/video/BSt7U-yOa4Q/видео.html

  • @karenbaxter2706
    @karenbaxter2706 4 года назад +1

    What do you recommend for a cheap small drift car for under £80

    • @BeaversHobby
      @BeaversHobby  4 года назад +2

      Either Mini-Q TRQ1 or WLtoys K969/K989.
      TRQ1 is a good chassis but electronics is fragile. This one is a gamble. If the circuit board hold up it will be the best car to start. Other components are quite durable. Overall it doesn't drive as well as WLtoys and it doesn't have much headroom to modify.
      WLtoys is the fastest in the budget category and has a lot of headroom to upgrade and modify. However the plastic is brittle and gears wear out very quickly.
      K989 and K969 are essentially the same car.
      K989 is rally/touring because it comes with open gear diff and grip tyres.
      K969 is labelled as drift car because it comes with solid axles (permanently locked diffs) and drift tyres.
      Choose whichever body you like because you'll want to change the tyres anyway and a differential can be locked later.
      However it will need a bit of fixing to get it to work. I have entire video series for that. But just to get it working properly, follow episode 1 and 2. ruclips.net/p/PLS79G3YjA2fAEez9GVeLW3JIy_LUIb6Mb
      In conclusion, you have to choose between dodgy electronics from TRQ1 or fragile gears from WLToys.

  • @jesseco9964
    @jesseco9964 3 года назад +1

    Are you using a gyro for the drift sections?

    • @BeaversHobby
      @BeaversHobby  3 года назад +2

      No, I don't. Actually I don't use a gyro in any AWD cars. I feel it's more of a hindrance than a help especially in a small space.
      I only use it in RWD cars where it's necessary.

  • @andresrodriguez623
    @andresrodriguez623 4 года назад

    Would wltoys electronics fit on this chasis

  • @aliffaslam7289
    @aliffaslam7289 4 года назад +1

    sorry i just newbie, wanna ask, if i but this, is it come with the remote controller?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Now, this is kit car and you will have to buy remote controller (transmitter & receiver), battery, wheels, body, batter and charger separately.

    • @aliffaslam7289
      @aliffaslam7289 4 года назад +1

      thanks, but i'm just play it for hobby only, i mean not so serious hobby, can u suggest for me car like this scale but come with all part, just plug and play, a bit boring now because of Covid got nothing to do right now

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@aliffaslam7289 Mini-Z is the easiest one to get and there're dealers everywhere because it's from Kyosho.
      Here's a review of RWD version for driving around. ruclips.net/video/ht69BmKDUlc/видео.html
      There's also AWD that you can both drive and drift. ruclips.net/video/yp2b_Bf6smk/видео.html
      If you are on a tight budget, I highly recommend WLtoys K989. ruclips.net/video/TnhriaSSfSA/видео.html

  • @venturafilms8457
    @venturafilms8457 3 года назад +1

    Can u use the chassis and put a k989 electronics in it??

    • @BeaversHobby
      @BeaversHobby  3 года назад

      Yes, you can swap the electronics (I've also mentioned this in the video). However K989 cut one arm out of the servo so you might have to get a new one so you can screw it in the mount. Otherwise just just a double sided tape.

    • @alexk.8294
      @alexk.8294 3 года назад +1

      Hey,
      i dont know if this is happening to everyone but one Thing i have to mention:
      If you get the hyper steering Upgrade, you better have a Radio where you can Set Servo Limits (the Stock WL Toys doesnt)
      Thats the reason i broke my new kyosho Front way diff. The reason: when i full steered, the rods moved so much that they moved the gearbox a Bit.
      Hope that helps you

  • @johnfaustus1
    @johnfaustus1 2 года назад +1

    How do you think this compares to the BZ3 (which is belt-driven, I know)?

    • @BeaversHobby
      @BeaversHobby  2 года назад

      BZ3 is better. Well, it's the best AWD belt-driven right now.

    • @johnfaustus1
      @johnfaustus1 2 года назад +1

      @@BeaversHobby Thanks, and what is easier for a new racer, the BZ3 (AWD) or the MRT (RWD)?

    • @BeaversHobby
      @BeaversHobby  2 года назад +1

      @@johnfaustus1 MRT should be easier and has less parts to worry about.

  • @erikfernandez4494
    @erikfernandez4494 4 года назад +1

    Really can't wait for mine to arrive, expecting some delays cause of covid-19. If i may just ask, how long does it run on 300mAh battteries?

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      I got 30-45 minutes of runtime depending on how hard I pull the throttle.

    • @erikfernandez4494
      @erikfernandez4494 4 года назад +1

      @@BeaversHobby wow that's alot for 300mAh. Guess adding LED lighting won't hurt then. Thank you, kindly

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@erikfernandez4494 Adding LED won't consume much power. You can do it without any problem.

    • @erikfernandez4494
      @erikfernandez4494 4 года назад +1

      @@BeaversHobby awesome! great to know. Only thing i'm lacking now is the oneway front diff, 'literally cant find one available anywhere and my lack of knowledge in RC world hinders me from finding alternatives.

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@erikfernandez4494 I've found some on Aliexpress. Cheapest one here. www.aliexpress.com/item/33012812405.html
      In this shop it shows that there are shims in the one way kit. www.aliexpress.com/item/33045636252.html
      In case you want other colour. www.aliexpress.com/item/32845387412.html

  • @RcModwerks23
    @RcModwerks23 4 года назад +1

    This little rc car looks interesting for drifting indoors... how does it compare to Wltoys A252 & A242 ? 👍

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      This one is in a different league. It's one of the best AWD drift cars you can get right now.

    • @RcModwerks23
      @RcModwerks23 4 года назад +1

      @@BeaversHobby Thanks, ... maybe I´ll get one soon

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@RcModwerks23 My pleasure.

  • @onlinehelper374
    @onlinehelper374 2 года назад +1

    For what is third battery wire?

    • @BeaversHobby
      @BeaversHobby  2 года назад

      When there are 3 wires it's the balance plug where the 1st one is - of the 1st cell, 2nd wire is the + of the 1st and - of the 2nd cell, then 3rd is the + of the 2nd cell.

  • @jays604
    @jays604 Год назад +1

    Will the K989 body work on the AMZ chassis?

    • @BeaversHobby
      @BeaversHobby  Год назад

      Yes, it will. You will need to get the lexan body mounting kit (body posts) though.

    • @jays604
      @jays604 Год назад +1

      The body posts from Wltoys or AMZ? Thanks for the help.

    • @BeaversHobby
      @BeaversHobby  Год назад

      @@jays604 For the AMZ. It has its own set of poles. I forgot you will need to drill new holes as well. www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1024&products_id=12227

  • @colterjones9261
    @colterjones9261 4 года назад +1

    Hey i was gonna msg you. I was gonna see about getting an opinion on the (jjrc q36-jjrc q36) 1/26 vehicles and their compatability with parts from the wltoys and mini q aswell as a drift build. Can you please get back to me. You are the reason i now order from banggood and also the reason why i have been making a drift build from the p929 wltoys 1/28

  • @Ymerstudios
    @Ymerstudios Год назад +1

    Is this better than a k969 with a bunch of upgrades?

    • @BeaversHobby
      @BeaversHobby  Год назад +1

      Yes, it's way better. Even a stock AMZ is better than upgraded WLtoys.

    • @Ymerstudios
      @Ymerstudios Год назад +1

      @@BeaversHobby how much was this total?

    • @BeaversHobby
      @BeaversHobby  Год назад

      ​@@Ymerstudios That depends on what you have already and what kind of electronics and transmitter you will be using.
      If you already have everything from transmitter to battery and charger, it'll be about $180 for the car with electronics, wheels+tyres and a body.
      If you haven't got anything yet you are looking at about $290. Basically $110 extra for a battery, a good charger and a decent transmitter. Remember, these 3 things are what you will be keep using for years to come so it's more of an investment at this point.

  • @thatonebeone
    @thatonebeone 4 года назад +2

    What's the best things to get for drifting ? What one to build and parts to get ? Thanks

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      For AWD/4WD drifting, this AMZ is one of the best. You can get car and parts from miracle-mart.com . It's a bit hard to mod it to CS so if you want a better car to do CS then I suggets Mini-Q Q7. You can get the car from banggood.com and parts from hobbyking.com under "turnigy tz4" and "mini-q" name, also at aliexpress with "mini-q mosquito car" name.
      As for RWD drifting, right now Atomic DRZ is the best to get in terms of durability and part support. you can get it from miracle-mart.com .

    • @thatonebeone
      @thatonebeone 4 года назад +1

      @@BeaversHobby thanks

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@thatonebeone My pleasure.

    • @thatonebeone
      @thatonebeone 4 года назад +1

      @@BeaversHobby looking at this.. any good specs? Thanks godracing.com/index.php?route=product/product&product_id=206

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@thatonebeone This XRX DPA drifts better than DRZ but it's brittle. It can break even from minimal driving. Some say there's a new batch which is better so you'd better ask them if they got the improved parts.

  • @TiagoDeOliveiraHH
    @TiagoDeOliveiraHH 3 года назад +1

    hey! me again :D I bought an atomic amz, and I would like to know what are the essential upgrades to run well. And what upgrades should I do to drift

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      Hyper steering bell crank, front one way, rear solid axle (can also lock the original ball diff) and soft front springs are all you need. Next is just choosing the tyres according to your floor. DS Racing make a lot of good tyres. Choose between LF-1 to LF5, LF-1 = mid-high grip for all surfaces with decent speed, LF-5 = lowest grip available for carpet or slow drifting.

    • @TiagoDeOliveiraHH
      @TiagoDeOliveiraHH 3 года назад

      @@BeaversHobby Nice! tank you o/

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      @@TiagoDeOliveiraHH My pleasure. Good luck with the project!

    • @TiagoDeOliveiraHH
      @TiagoDeOliveiraHH 3 года назад +1

      @@BeaversHobby do you have the link from rear solid axle?

    • @BeaversHobby
      @BeaversHobby  3 года назад +1

      @@TiagoDeOliveiraHH You can just tighten the ball diffs that come with the car so you don't have to buy it. However if you want to buy the whole set one way + solid axle, I bought the whole set from this. www.aliexpress.com/item/1005001671065507.html It's the same unit like the original Mini-Z parts.
      The quality is great and the gear won't chew the centre shaft pinion like the new sinohobby part with metal gear.
      However you'll have to shave the gearbox a bit to make it fit.

  • @piotrkarpienia4779
    @piotrkarpienia4779 4 года назад +1

    Is it really better or at the same level as Kyosho? It looks its more expensive. Buying Kyosho youre getting full package, great quality for 150$ or even 120$, ready to rock.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      If you don't already have transmitter and charger, with everything included it'll cost roughly the same as Mini-Z AWD Ready Set. But the performance is about EVO version.
      The chassis itself is far better than all older Kyosho AWD and about the same level of consistency as MA-030 (current one). Another big plus is the freedom that you can use any electronics you want from motor, ESC, servo to radio, not proprietary parts from Kyosho. So if anything breaks you can fix it very easily. It also has much more steering angle so drifting is much easier too.
      However, as you have noticed, it's not entirely beginner friendly as you'll have to choose many parts yourself, which is a nature of kit car. Think of it as a Tamiya TT01 Kit in 1/28 scale.

    • @piotrkarpienia4779
      @piotrkarpienia4779 4 года назад +1

      @@BeaversHobby Cool man. Thanks for explanation :D

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@piotrkarpienia4779 My pleasure.

  • @adriancjones
    @adriancjones 4 года назад +1

    I bought an atomic AMZ 2wd (it’s my second atomic 1/28). I’m trying to assemble. The screws that go into the bottom bulkhead are very soft and break off when you try to screw them in. I would suggest not buying one of these. I have emailed them to see if they will replace the bulkhead. Have not heard from them yet.

    • @BeaversHobby
      @BeaversHobby  4 года назад +2

      Sorry to hear that. Hopefully you got reply soon. They haven't answer my message so I've given up already.
      Lately Atomic's QC has gotten worse. A few people who got AMZ after me got dogbones that won't fit knuckles properly. Not sure if right now there's any brand in this price range that has decent quality control though.

    • @adriancjones
      @adriancjones 4 года назад +1

      Beaver's Hobby that is sad. I enjoy assembling kits. It’s hard to find good kits anymore. Everyone wants ready to run.

  • @IBangkneeBakks
    @IBangkneeBakks 4 года назад +1

    and a link to the body posts and soft lean bodies please
    awesome videos btw

    • @BeaversHobby
      @BeaversHobby  4 года назад

      Sorry for the inconvenience and thanks for notifying me.
      Here they are.
      Body post kit for lexan body: www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1024&products_id=12227
      Lexan bodies: www.miracle-mart.com/store/index.php?main_page=index&cPath=67_74_1045_1046&pg=categories
      The soft body I show in this video is from Mini-Q: bit.ly/2MIiB4k
      The bodies are out of stock at the moment. However you can check out www.markaracing.com/ because they make soft bodies too. They also make truck body. www.minizracing.it/minizshop/index.php?main_page=product_info&cPath=906_907&products_id=11692
      Also check out Kenonhobby, if you are outside US the shipping can get really expensive though. www.kenonhobby.com/search.asp?keyword=lexan+body&search=GO

  • @Victor2K23
    @Victor2K23 2 года назад +1

    What a ball differential you used in your amz

    • @BeaversHobby
      @BeaversHobby  2 года назад

      They are not ball diffs in this build. The front is Sinohobby front one way and the rear is Eagle Racing solid axle. If you want to use the ball diffs, the original ones that come with the kit are good already.

    • @Victor2K23
      @Victor2K23 2 года назад +1

      @@BeaversHobby thx because I failed to build included ball differential

    • @BeaversHobby
      @BeaversHobby  2 года назад +1

      @@Victor2K23 You can also use GL Racing GLA ball differential. The quality and build are better than the Atomic's.

    • @Victor2K23
      @Victor2K23 2 года назад +1

      @@BeaversHobby thx

    • @BeaversHobby
      @BeaversHobby  2 года назад

      @@Victor2K23 My pleasure.

  • @FRAKKKA
    @FRAKKKA Год назад +1

    I've got the esc it came with and got some questions.
    It's got 6 cords coming out the top 3 for motor I'm assuming other three are for battery.
    And what are the two connectors on face of esc are they both for the receiver?

    • @BeaversHobby
      @BeaversHobby  Год назад +1

      The flat, white plug is for the motor. The small plug is for the receiver. The top port (facing upwards), the one that is the same type as the plug that goes to the receiver, is for Hobbywing programming card. And the biggest port is for the battery.

    • @FRAKKKA
      @FRAKKKA Год назад +1

      @@BeaversHobby can I email you picture of the mess I made lmao

    • @BeaversHobby
      @BeaversHobby  Год назад

      @@FRAKKKA Sure. My email is beavershobby@gmail.com

  • @karenbaxter2706
    @karenbaxter2706 4 года назад +1

    How much is it all in

    • @BeaversHobby
      @BeaversHobby  4 года назад

      It depends on what you have already.
      For the car, body, battery and adapters $212.46.
      If you haven't got a radio it'll range from $20-$600. I suggest Radiolink RC4GS which is $54 and does everything.
      As for the charger you can get a cheap USB charger for $3. Or go all the way with genuine SkyRC iMax B6AC for $60.
      So a budget setup is around $270 if you don't have anything yet minus the paint, glue and tools to build, of course.
      Links below.
      Chassis with electronics: www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_1037_1040&products_id=13049
      Shims for diff. : www.miracle-mart.com/store/index.php?main_page=product_info&cPath=83_1066&products_id=6103
      Hyper steering bell crank upgrade: www.miracle-mart.com/store/index.php?main_page=product_info&cPath=67_74_1024&products_id=13067
      Body, highly recommend Skyline R33 Nismo because you got the wheels with it too: bit.ly/36fUGil
      Tyres, in case you want some spare: bit.ly/2I3a74k
      Upgrade Front oneway: bit.ly/2YFi1Y7
      Solid axle isn't needed. You can lock the ball diff that comes with the car ans save $15.
      Wheel nuts: bit.ly/2Lck02G
      Budget Radio Radiolink RC4GS: bit.ly/2WSjb0G
      What I actually use, Flysky Noble NB4: bit.ly/2FVvIdy
      Battery: bit.ly/340Liik
      Parts for converters you'll need.
      Battery Plug (ESC side) JST-PH 2.0: goo.gl/69G4zW
      Battery Plug (battery side) JST-XH 2.5: bit.ly/3bj4eM6
      Receiver Plug JST-XH 1.5: goo.gl/Mhy8pV
      Receiver Plug if you need to convert to standard receiver: bit.ly/3aV9VQU
      Battery charger, you can get by with a cheap USB charger. bit.ly/3dNodTW
      But I highly recommend a genuine SkyRC. Buy it once and use it forever: bit.ly/2KTGYJC
      Some of this are be out of stock so you can find the substitute based off the part I tell you.

  • @beepovews4392
    @beepovews4392 2 года назад +1

    Can you provide link for locked diff?

    • @BeaversHobby
      @BeaversHobby  2 года назад

      It's getting hard to find that nowadays. The only source I can find is the official site of EagleRacing and it's out of stock. www.broadtech.hk/eagleshop/shop/ShopProductDetail.aspx?id=3646U
      However if you only want locked diff you can tighten the original ball diff to lock.

    • @beepovews4392
      @beepovews4392 2 года назад +1

      Thanks so much. You helped a ton through my build. (Just finished)

    • @beepovews4392
      @beepovews4392 2 года назад +1

      Sorry, I didn’t read properly. I think I’ll just tighten it or put a bunch of glue in it

    • @BeaversHobby
      @BeaversHobby  2 года назад

      @@beepovews4392 Yes, do that and you don't have to buy anything.

  • @pietrod2052
    @pietrod2052 4 года назад +1

    Ciao ho comprato una atomic amz 4wd con iper stering e in piú l'aggiornamento in alluminio della manovella dello sterzo e il corno del servo. Io monto il servo che c é in dotazione nel kit di montaggio dell' amz 4wd e non riesco a montare il corno sul servo perché la corona del servo é troppo piccola rispetto al corno mi puoi dare qualche consiglio su come fare

    • @BeaversHobby
      @BeaversHobby  4 года назад

      The horn from kit won't fit but a horn from servo set will fit. Check in the servo bag, they should be there. They are white servo horn.

    • @pietrod2052
      @pietrod2052 4 года назад

      @@BeaversHobby ok grazie ma ciò vuol dire che il corno in alluminio lo vendono ma non si puó montare..

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@pietrod2052 Yes, exactly.

    • @pietrod2052
      @pietrod2052 4 года назад +1

      @@BeaversHobby ok grazie

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@pietrod2052 My pleasure.

  • @01TonyPayne
    @01TonyPayne 4 года назад +1

    In your opinion which is better? AMZ or Q7?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      They are great in different ways, for me it's really difficult to choose between those two. If I can really choose one car then I'd take AMZ mainly for durability and parts support.

    • @01TonyPayne
      @01TonyPayne 4 года назад +1

      @@BeaversHobby that is good to me, thanks!

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@01TonyPayne My pleasure.

  • @FRAKKKA
    @FRAKKKA Год назад +1

    When my wheel is turn to right all the way with bell crank, some times the car just goes straight and doesn't turn even though wheels are turned

    • @BeaversHobby
      @BeaversHobby  Год назад +1

      Check if it lifts the wheel. If you set the EPA too high sometimes it will just lift the wheels and you won't have any directional control so you'll have to decrease the EPA.

    • @FRAKKKA
      @FRAKKKA Год назад

      @@BeaversHobby down to 2
      40% both sides still seems to slide straight/ barely turn for a bit on right turns mid speed. I have to either blast the throttle to whip the tail or go slow to make a tight turn

    • @BeaversHobby
      @BeaversHobby  Год назад +1

      @@FRAKKKA Then there's something wrong with your steering system or differential. Check if the differential doesn't lock when you turn right and also if the ball heads are too tight so they pull the wheel up when you turn.

    • @FRAKKKA
      @FRAKKKA Год назад

      @@BeaversHobby using the hyper bell crank and kit came with carbong fiber servo mount, servot moves around quite a bit if I leave the epa at 100% looks like the steerid rod hits the servo horn

    • @FRAKKKA
      @FRAKKKA Год назад

      @@BeaversHobby also I've got the lug nuts fastened all the way but my front wheels still got a good amount of play

  • @ggjflyguy
    @ggjflyguy 4 года назад

    great Video, i got the Atomic BZ and i love it, also check out GL Racing GLR i have that one also love them both, much more durable than the Mini Z cars.

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      Both GLR and BZ are great cars.
      Since I don't have dedicated race track and think GLA would suite me better.
      Right now I'm on the fence between MA030 EVO and GLA. The more I do the research the more MA030 become less appealing.

    • @ggjflyguy
      @ggjflyguy 4 года назад +1

      @@BeaversHobby My GLA is my go to for racing, yes i love my BZ also but the GLA just feels and runs a lot smoother

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@ggjflyguy Thanks for the info.

    • @yongxuehuang9347
      @yongxuehuang9347 4 года назад

      Beaver's Hobby What do you dislike about the ma030evo?

    • @BeaversHobby
      @BeaversHobby  4 года назад

      @@yongxuehuang9347 List from the things I gathered from talking to people who got the car ranking from annoyance to unacceptable.
      - Very limited body compatibility as it's based on FWD chassis.
      - Can only do 98 and 94mm wheelbase for AWD configuration, for 90mm you can't do AWD, only FWD.
      - Very hard to pull the batteries out.
      - Floppy tie rod, if you look at the design you'll understand. the knuckle slots extend out of main shaft creating weak points and prone to break. Narrow rod got toe in, difficult to drift. Wide rod is extremely floppy. Need aluminium upgrade ASAP.
      - Extremely fragile wiring.
      - Off-centre steering, need ICS adapter to do calibration. That's another ~$24 on top of the car that costs roughly 250 Euros in my region (about 276 USD).
      These are just what the others found. Who knows what more I'd find if I had bought the car.
      On top of that $50 for a proprietary receiver is also a rip-off.
      The only good thing about 030 is left-right weight balance.
      If I paid over $300 for a car I expect perfection.
      At this point if I would try this chassis, I'd just buy a FWD and convert it to AWD. I won't buy an EVO.

  • @nitroalone2622
    @nitroalone2622 4 года назад +1

    รุ่นที่มีชุดไฟมา ใช้กับรีโมทแบบไหนได้บ้างครับ

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      ใช้รีโมทรถได้ทุกแบบครับ ขอแค่รีซีฟเล็กพอจะใส่บนรถได้ก็พอ (หรือจะรีโมทเครื่องบินก็ได้ ขอแค่ก้านมันดีดกลับตรงกลาง)
      ปลั๊กที่เห็นเป็นหัวแปลก ๆ นั่นคือ JST-ZH 1.5mm 3 pin สามารถแปลงรีซีฟปกติให้ใส่ได้ครับ

    • @nitroalone2622
      @nitroalone2622 4 года назад

      ความกว้างจากล้อซ้ายไปล้อขวาเท่าไรครับ

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      @@nitroalone2622 แล้วแต่ล้อที่ใช้เลยครับ ตอนนี้ผมใช้ออฟเซ็ต 1.5 ได้รถกว้าง 67มม. ถ้าเป็นออฟเซ็ต 0 ก็จะได้ 64มม.
      ส่วน tracking หรือระยะระหว่างกลางล้อ 59มม. ครับ (ขึ้นอยู่กับออฟเซ็ตอีกนั่นล่ะ)
      ถ้าถอดล้อออก ดูเฉพาะนัคเคิลจะได้ 53.5มม. ครับ

    • @nitroalone2622
      @nitroalone2622 4 года назад +1

      แบบนี้ก็ใส่บอดี้ civic type r ได้ใช่ไหมครับ ตอนนี้ผมใส่wl ล้อมันล้นมาเกือบ2มิลครับ

    • @BeaversHobby
      @BeaversHobby  4 года назад +1

      ​@@nitroalone2622 Civic Type R ใส่ได้เลยครับ ใช้ล้อที่ติดมากับบอดี้ได้เลยด้วย ที่ WLtoys ใส่ไม่ได้ เพราะมันเป็นโครงกว้าง(ต้องเปลี่ยนล้อเป็นออฟเซ็ต 0 ก่อน ถึงจะใช้ได้) อันนี้มาเป็นโครงแคบ ตามแบบฉบับ MA010/020/030 เลยครับ

  • @genkikaneko
    @genkikaneko 4 года назад +1

    あなたの言葉は心地いい