I ended using a 6" piano hinge after making an aluminum plate I cut similar to his and drilled holes to match the rear of the XJ body and it worked out great! This video was very helpful in my idea.
@@operation11charlieinc They do make a truck hard body one I'm thinking about getting one later on bud u should definitely get the Cherokee look on Amazon were I got this one 😁
Yes technically you dont have to adjust anything. I did adjust the lower and upper links forward one notch, but u don't have to. Other then that you dont have to adjust anything to have the body fit on the Chassey. hope That made sense😄👍
Very clever solution!! 😎 I gotta go back and screenshot the hell out of it! 😲😗 If I can get my Comanche Hardbody, I might do very similar. Can't believe I missed this! I wanted to know what you came up with. Like I said, very clever. Carmine 🚂🚙
Thank you I just came up with the piece of aluminum and a couple small hinges that a had laying around And just mounted on to the rear chassis brace where the bumper would go And wallah. I just made a cardboard template are a piece of paper Before I could the aluminum I do you wanna fairly thicker piece of aluminum but not too thick because you also don't want it to bend when you lift the body. Hope all of that make sense
It really does. I'm also the "draw outside of the lines" kind of guy when it comes to building these. Just look at it, and the crap you've got lying around, until an idea hits!! 😉
I hot glued the interior underneath the hood & the side of the body to hold the interior. I also just cut a little piece so the guy's leg would slide through👍
I'm new to RC world, I'm a Chevy guy, I'd like to put a 73' Chevy body on my Gen 8, will any 1/10 scale body fit or do I have to look into specific measurements of fender wells placement, body lenght & width etc?
You can use body post or any other means of mounting the body on to the chassis I don't think you can mount the whole body on Fenders because the back doesn't have any brace to mount 2 unless you make some. If you have this body it should I came with mounting brackets
I wrote QUESTION wrong...sorry buddy...I mean if I have gen8 pack and Ordered inner chassis fenders...I'm running no lights at all...I'm only trying to cut back lexan interior square allowing shock towers to pass thru,for lower sitting of jeep CHEROKEE on gen8 pack chassis...will the jeep CHEROKEE be able to sit flush with inner gen8 chassis fenders on the gen8 pack?????...My question is only about the jeep CHEROKEE being able to sit/fit on gen8 pack with gen8 inner chassis fenders on????...""Sorry OZBOY81'''YOUR THE ONLY ONE AND BEST ONE ON RUclips BROTHER TO ANSWER MY QUESTION!!!...LAST QUESTION WHAT DID U USE TO PAINT DOOR TRIM??AND FRONT WINDSHIELD WINDOW TRIM ETC????AGAIN I APOLOGIZE FOR THE LONG MESSAGE BROTHER,,THANK YOU SO MUCH OZBOY81🤜🤛🙌
@@josecanseca8979 if you want the body to line up with the wheel base of the gen8 chassis, keep in mind that you can adjust the wheel base a little bit. if you keep the wheel base to what I think is 12.3mm the cheerokee body will only sit as low as the chassis rails will allow. the lower grill, if you center the body to the wheelbase the lower part of the grill on the body will hit the frame rails in the front. It won't entirely, from what I remember, sit right on top of the inner fenders. I used a KRYLON short cuts paint pen for the trim. Hopefully I answered your questions. Appreciate you watching my videos and asking for advice, sometimes its kind of hard to explain when you put it into writing. So again, thank you.
@@ozboy8144 OZBOY81,,THANKS MAN.>I ORDERED THE 324MM WHITE JEEP CHEROKEE ONE,THERES A 313MM AND 324MM,AND PACK COMES 324MM I BELIEVE,IM ORDERING THAT PEN NOW,OH SORRY I USED UR SKATEBOARD IDEA,,GREAT VISION🤜🤛
👍Nice job!
Thank you Shen 👍😁
This is going to make mounting my son's Comanche body so much easier. Great video bud, way to go 👍🤘
Thank you Glad I was a little help
Nice work! It really gets the job done!
Thank You!
Nice work man.... It’s great when stuff just comes together. 😎👍🏻
Thank you Kingston 👍
very good workman ship, that really came together well. Good job.
Thank you 😁👍👍
Thanks for the good ideal! Awesome
Your welcome thanks for watching 👍👍
Great video!!! Great info!!
Thanks Rick 👍
Nice work!!! 👍✔...NC MOUNTAINS ❤..
Thank you 👍😁
Great work! 👍
Thank you!
Nice job Oz. I did the same thing on my JK build, I had to make the brackets for mine but it works great. Great video👍🏻👍🏻
Nice... u do some amazing work injoying watching your channel bud😁
Thank you for watching and the compliment bud 😁👍
looks cool mate i love it BIG LIKE
😀 thank you for watching
Awesome job great video nice way to make it work very cool
Thank you I like how it came out works really well😀
O z boy 81 that is one nice mounting modification great work bro also pretty cool camouflaging that whole with the skateboard 🐢🐢👍👍🤘🤘👏👏👏
Thanks bud for the nice compliment 👍😁
@@ozboy8144 can't sleep either
Wow you got a lot of views on this video! Very helpful
oh man I wish you had a link to those hinges.. I think you need to find them with 1cm hole spacing
I ended using a 6" piano hinge after making an aluminum plate I cut similar to his and drilled holes to match the rear of the XJ body and it worked out great! This video was very helpful in my idea.
Great tips bud😎🤘 getting ready to buy another Gen8 pak chassis
Your welcome 😀
Looks good, I like those wheels 👍🏻
Thank you I thought they fit the Build pretty good😁 Got on Amazon relatively cheap. As always bud thank you for watching👍
Sweet , I been looking into this body for a while,,, that's what hold me back good info brother
Thanks bud I'm not the best At explaining things so hopefully it did help you😁
@@ozboy8144 did good brother
@@operation11charlieinc They do make a truck hard body one I'm thinking about getting one later on bud u should definitely get the Cherokee look on Amazon were I got this one 😁
@@ozboy8144 👍🤙
There’s always a way. 👍
For shour 😄 just have to be a little Creative
Good job man plus like the paint gonna get either the suv or pick up of this body very soon was looking for idears
That's Awesome I have the pick up as well. I think you'll enjoy either or Thanks for watching
Finally some help
Thanks a ton
Your welcome 👍😁😁
Who makes that hardbody ? .. nice ! peace
INJORA
If you’re using this body isn’t it a12.3 wheelbase? If so what did you have to do to adjust length of wheelbase to make it work?
Yes technically you dont have to adjust anything. I did adjust the lower and upper links forward one notch, but u don't have to. Other then that you dont have to adjust anything to have the body fit on the Chassey. hope That made sense😄👍
OZBOY 81 right on bro I’m thinking about getting the Gen 8 pack but want to use a 12.3 body
Very clever solution!! 😎
I gotta go back and screenshot the hell out of it! 😲😗
If I can get my Comanche Hardbody, I might do very similar.
Can't believe I missed this! I wanted to know what you came up with. Like I said, very clever.
Carmine 🚂🚙
Thank you I just came up with the piece of aluminum and a couple small hinges that a had laying around And just mounted on to the rear chassis brace where the bumper would go And wallah. I just made a cardboard template are a piece of paper Before I could the aluminum I do you wanna fairly thicker piece of aluminum but not too thick because you also don't want it to bend when you lift the body. Hope all of that make sense
It really does. I'm also the "draw outside of the lines" kind of guy when it comes to building these.
Just look at it, and the crap you've got lying around, until an idea hits!! 😉
I’m hoping to do the same on a gen7 sport
That's awesome.. I recently got rid of this one but I want to do another build
Mantap kawan
How did you mount the interior to the body? Also you figures, did you cut the legs to fit in the seat? I am doing the same one for my traxxas TRX4.
I hot glued the interior underneath the hood & the side of the body to hold the interior. I also just cut a little piece so the guy's leg would slide through👍
Hello, greetings from Colombia, you have the link where to buy the body, thanks
www.amazon.com/INJORA-Plastic-Wheelbase-Cherokee-Crawler/dp/B074GM9854/ref=mp_s_a_1_1_sspa?crid=2LY59FNGUHG7T&keywords=injora+jeep+body&qid=1667867400&sprefix=Injora+jeep%2Caps%2C204&sr=8-1-spons&ufe=app_do%3Aamzn1.fos.006c50ae-5d4c-4777-9bc0-4513d670b6bc&psc=1
looks like there alot more on ebay right now
I'm new to RC world, I'm a Chevy guy, I'd like to put a 73' Chevy body on my Gen 8, will any 1/10 scale body fit or do I have to look into specific measurements of fender wells placement, body lenght & width etc?
Most 12.3 body should work just keep in mind that somebody's are not as white as others
@@ozboy8144 Not as white?
@@c21aaron oops 😂 Sorry about that Not as wide
awsome I want this body for mine just couldent fing any body mounting it
Thanks for watching it does come with body mounts but I made my own
Nice custom mounting homie✌💪
Thank you Voodoo 👍
HEY brother I Have a question IF IM RUNNING No LIGHT SETUP AT ALL,CAN I MOUNT THE JEEP ON THE CHASSIS FENDERS?any FEEDBACK GREATLY APPRECIATED
You can use body post or any other means of mounting the body on to the chassis I don't think you can mount the whole body on Fenders because the back doesn't have any brace to mount 2 unless you make some. If you have this body it should I came with mounting brackets
I wrote QUESTION wrong...sorry buddy...I mean if I have gen8 pack and Ordered inner chassis fenders...I'm running no lights at all...I'm only trying to cut back lexan interior square allowing shock towers to pass thru,for lower sitting of jeep CHEROKEE on gen8 pack chassis...will the jeep CHEROKEE be able to sit flush with inner gen8 chassis fenders on the gen8 pack?????...My question is only about the jeep CHEROKEE being able to sit/fit on gen8 pack with gen8 inner chassis fenders on????...""Sorry OZBOY81'''YOUR THE ONLY ONE AND BEST ONE ON RUclips BROTHER TO ANSWER MY QUESTION!!!...LAST QUESTION WHAT DID U USE TO PAINT DOOR TRIM??AND FRONT WINDSHIELD WINDOW TRIM ETC????AGAIN I APOLOGIZE FOR THE LONG MESSAGE BROTHER,,THANK YOU SO MUCH OZBOY81🤜🤛🙌
@@josecanseca8979 if you want the body to line up with the wheel base of the gen8 chassis, keep in mind that you can adjust the wheel base a little bit. if you keep the wheel base to what I think is 12.3mm the cheerokee body will only sit as low as the chassis rails will allow. the lower grill, if you center the body to the wheelbase the lower part of the grill on the body will hit the frame rails in the front. It won't entirely, from what I remember, sit right on top of the inner fenders.
I used a KRYLON short cuts paint pen for the trim. Hopefully I answered your questions. Appreciate you watching my videos and asking for advice, sometimes its kind of hard to explain when you put it into writing. So again, thank you.
@@ozboy8144 OZBOY81,,THANKS MAN.>I ORDERED THE 324MM WHITE JEEP CHEROKEE ONE,THERES A 313MM AND 324MM,AND PACK COMES 324MM I BELIEVE,IM ORDERING THAT PEN NOW,OH SORRY I USED UR SKATEBOARD IDEA,,GREAT VISION🤜🤛
Where can I get a body like that?
Amazon or eBay this one is a Injora body
@@ozboy8144 Thanks
did you change the wheelbase?
If I recall I think I adjusted the links in "1 noche front and rear
Hi. What is the diameter of the wheels, 100 mm?
I don't remember The tires are proline 1.9 NOT in the XL Size rims also 1.9
They broke off after one run for me
Are you talking about the mount That attached to the rear bumper?🤔
@@ozboy8144 No to the front. It pulled out of the plastic..
@@royzala631 Ooh Man sorry to hear that 😞 u have away to fixed it
@@ozboy8144 no prob man just drilled holes for clips.
Thankssss
your welcome
I can’t really see anything
what can't you see?