Thank You!! I use your demo about a year ago and refer to it when I build my quadcopters. Still learning the dynamics of the KK2 board as well as the flight controller. Again Thank you!!
Wow you did a good job explaining the setup of KK 2.1 board. Had to be one of the clearest videos on setup of one i came across. I used Naza and Apm and Pixhawk the KK is a brave new world for me lol!! For the life of me could not find a simple example of esc tuning for the KK till this video!
Can you help me? I have a safe transmitter and it won't start on full throttle, it tells me to turn it down before it boots. How can I calibrate the ESCs?
Hey love your channel and have been coming back to this video to troubleshoot my kk2.1 board. I wanted to ask how you wired the voltage metre. Have you gone from the battery connector to the voltage metre to the pdb?
dooseyboy, I no longer have this particular flight controller, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
New to diy quad pardon what may seem like dumb question but with opto esc's am I removing both the + and - off the esc wire and replacing with + and - from the bec wire to power the kk2 at m1 pin
I am currently using the firmware created for the KK2.1 by Steveis over on RC Groups. I am using the "Lite" version which is more for beginners. The firmware is called: KK2V1_1V17S1Lite
They are carbon fiber, and the set of 4 cost me around $35. The link I had saved is no longer active from RC-Drones where I purchased them. They work and look great, but I recently had to replace them because my new gimbal didn't have enough clearance. I will post an update soon showing the new ones.
I,ve been watching a few videos on programming za kk2.1. Why would you have channel 5 for shutting off flight stabilization? I mean, wouldn’t you want it on all the time?
Followed your setup the letter and she flies though a bit twitchy compared to others I have. I do not have GPS on it yet though. One thing I noticed is I can do a CCW funnel with no problems, but CW is very wide and not able to complete the instruction. Is there some setting I need to correct.?
Great "how to" video. Question about self level settings. How do I give myself more control and less to the quad like for better bank turns. I am more of a sport flyer rather than FPV or video.
+jerry zito , I was running the Steveis KK2.1 Firmware that is geared more for beginners and / or slower reaction for use with a photography platform. He also offers a "Pro" version of the firmware which is much more responsive and better for stuff like Acro. Search for "Steveis KK2.1 V1.19S1 Updated Firmware".
hey +MrArmagedd0n, great video! Can you tell me where you got those landing blades located on bottom of each arms. Looking everywhere for those. Thanks. :)
I didn't buy them from this site, but it is the same product. May find it elsewhere for less $. drone-quadcopter.com/shop/drones/phantomount-carbon-fiber-landing-strut-extensions-for-dji-flamewheel-450-or-550/
That is a very nice setup. May I ask where did you get the landing skid Extension? I was checking on aliexpress and ebay, but I could not find one. There are other types, but I like the one you are using, I believe it will give the quad the best stability by landing.
Ranger80pl1, the place I purchased them no longer stocks the extensions. This site seems to have a very similar product, but a bit more expensive than what I paid. www.phoenixflightgear.com/Phoenix-Flight-Gear-F450F550-Flame-Wheel-Legs_p_15.html
Thank you for the link. It is expensive indeed. A bit too much for a part as simple as a copter landing gear. I believe I will need to check for other options.
Hello. I have a little question. I have KK2.1.5 flight controller and speed controller 4x RC Simonk 30A ESC Brushless Motor Speed Controller for Multicopter BEC 5V / 2A. To connect them have I disconnect the plus wire from BEC in M2-M4 connections and leave plus just only in the M1, or can i connected regular without disconnect anything (3 wire from BEC to controller )? Thanks Alex
Greetings! Nice video. I am having troubles figuring out how to power the board. If my speed controllers have BEC's, then I plug them in like normal and let speed controller 1 power the board, but then clip the power leads on speed controllers 2, 3,& 4 so it doesn't get over powered? Or do I just plug all speed controllers in like normal? I am using the board for the HK 250 quad copter and i am using all stock component. I would greatly appreciate your help. Thanks
Hi I have a question about the 9XR pro that you are running What reciever are you pairing it with? Im looking for a TX RX and im leaning twards the 9X with the 9X and 8channel RX from Hobby King, Your video REALLY helped me set up my SK450, now im looking to start upgrading. Thanks for sharing!
Outstanding! I just ordered the the Taranis plus combo fro Helibatics and it shipped today. But im having a HELL of time trying to get my SK450 to fly right, It seems to want to gyrate around Not stable and it flipped over on itself. Hopefully the Taranis and new reciever will help. Thanks for the response and taking the time to post up this video, Happy New Year!
+MrArmagedd0n Friend, I want'll make a tricóptero t3, I will use the radio Turnigy 6x FHSS with KK.2.1.5. I can calibrate the esc this anyway ??? if I remember correctly, I should put the stick in the maximum, connect the battery and then the esc 2 beeps slow down the stick? also would work I calibrates one esc to see using just the receiver?
+Raimundo Vieira, I sold my DYI quad and purchased a 3DR Solo, so if the answer isn't found in one of my older setup videos, I really can't be of much help. Sorry.
What kv are the motors? Also what props are you using? I built a quad w/ a Q450 (knockoff of DJI board.) I like the video, but when using your PI settings my quad flipped twice. The P was way to low. I'm using 1200KV brushless motors w/ 10x4.5 props. Decided to do a bit more research on PI settings before I try any more and found out that too low of P setting can result in a quad that can flip in autolevel mode. FWIW, I double and triple checked the controller, motor direction and props and everything is correct, it will get up in the air and try to stay stable, but as soon as I start to bring it back down it wants to flip.
TAZ427 Not sure what would be causing it to flip. I no longer have this particular quad (sold it), so can't help much with troubleshooting. As far as the motors go, whatever come with the original DJI Flame Wheel F450 Kit, is what I was using on this quad. Good luck.
HI, Thank you! Two questions: How do I know the numbers in the P1 Editor ( gains) , you said we have to experiment, what about setting up for the first time? None of my ESCs have BEC, using external BEC, Do I plug it into the RX? (aux), afraid I don't know how to make a modification like you. What do people usually do in this case. Thanks in advance...
Thought we may have been talking KK2.0, I could not find it on mine with V1.6 firmware. You could also mount it at 45 degrees and use either the X or + motor layout for + and X respectively to use the 45 degree offset build into the board. Always more than one way to skin a cat. Thanks for the link to the latest setup instructions, they are very informative and I may use them one day if I go back to using the KK2 boards.
teamscreem Oh, I just assumed that with the latest firmware the KK boards would be the same. Bit silly when I think about it since the different KK boards have different hardware and thus the firmware can't be the same. I can only speak for the 2.1.5 (which does have the offset feature), but I would assume the 2.1 also has that function.
Thanks! I have a HEX but only three of the motors spin up once I've gone through everything. Swapped wires around but no luck. (The problem motors seems to sort of vibrate/get stuck). Any ideas on what to look at for this?
blackdedo93 I don't have any links for the KK board, but search "Minim OSD Quick Installation Guide", and you will get tons of pictures / wiring diagrams showing the setup for connecting an OSD.
hi, I am using KK 2.1 all setup seems correct but when I increase the throttle with prop installed it disarm automatically. But when it is without prop it works
Hi, I am kind of stuck with this thing. I have connected it all and in safe mode all seems to be fine, in this radio test option, the controller does recognize all the sticks and is showing values when I am moving them, but after arming it, the only thing which seems to be functioning correctly is the throttle - it lifts off and lands - but that's about it. When I am trying to move the sticks like rudder, or elevation, to move the model in the air, nothing is happening. I did a test without the propellers and there was no change in engines speed when I was moving the right stick. Would you know what could be the cause of this?
I no longer have this particular flight controller, so I'm afraid I can't help troubleshoot. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help.
Funny to read some of these negative comments from people that are butt-hurt that I mention the word "drone". Maybe they have ample time to waste crying over semantics, but I sure don't.
+MrArmagedd0n You were nice enough to take time to help others set this thing up. I for one completely respect that and appreciate it as I just got one of these in trade and want to make sure it's set up right. Thanks again! And the trollers can go suck it. Let them go have a Drone/Quadcopter debate, We'll be out flying in the meantime lol.
I no longer have this particular flight controller or quad, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
hi. can you help please. how can i change between default Misc. settings to Misc. Settings 2 on screen? is it possible to do without usbasp - cause i have just the board. may be pressing buttons))?
Dear you like expert could you help me to setup qq super flight control with radio link At9 actually I done all connections but all motor is not spinning in the same time only spinning 2
hai sir,can you share me your setup?such as pi editor,stick scaling,misc set,self level,mixer editor...im new to this hobby sorry...hope you dont mind to share your setup :)
Hello sir .. can you please help me out with my quadcopter .. i have done evrything right i suppose and trying to do the calibration but the motor just didnt start .. it starts only while i push the 1&4 buttin together and i tried calibrating them individually but still not able to fly my quad please help sir.. i am in a mess ... i am using tranmistter fs ct6b and kk board 2.1.5
+Rohit Chauhan , I no longer have this particular flight controller, so can't test anything for you. Best bet would be user forums / communities dedicated to Quadcopters like DroneFlyers, DYIDrones, RCGroups, etc. Good Luck.
Help! I cannot get mine to arm? Just started doing this, can't understand why? I have checked and rechecked everything. The receiver is getting signals as the KK2 is reading them in the receiver test menu so I am stumped?
Not sure what is causing your issue. I no longer have this particular flight controller, so can't be if much help. Recommend heading to RCGroups forum as there are many active KK2.1 users that can help you out. Good luck.
Cameron if the motor is getting scorching hot that means there is impedance so something is wired incorrectly which is causing the voltage through that motor to be too high Without seeing it I can't advise but Totum hobbies should be able totalk you through how to wire it if you go down and see them. Love you son oh one point check the soldering to make sure there is no bleed of solder across contacts that would lead to faulty circuit and prevent the board working.
satendra singh tripathi yaw input error indicates that kk board is not getting any yaw signal from tx. its normal as when tx is off it does not gives yaw or any channel input. when u switch on the kk board with tx on the error screen will be gone
I no longer have this particular flight controller or drone, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
States are making laws to ban drones, not rc aircraft. If people like you trick the public into thinking that all rc aircrafts are drones they will ban our hobby. But that just won't sink into your head. Call it what you will. Your part of the growing problem
Most of the states (like here in Colorado) that are looking to initiate bans are specific to large game Hunting/Scouting. For that purpose, I completely agree that rc craft should not be allowed. If you did some research and actually read the language of those bills, the do not call out "drones" specifically, but also refer to them as "UAV", "UAS", and even "RC Aircraft" calling out the ability to take pictures or video while in the air as what constitutes the ban for Hunting activities. So again, semantics. It doens't matter what they are called, it is the ability for aerial survailance that some people (and the bills banning their use for certain activities) are worried about. The "growing problem" is not what people call these craft, it is accessibility. Since it is becoming easier for people to purchase and operate these devices, we are seeing a individuals doing stupid things with them (like flying close to airports, or snooping in people's windows). Unfortunately like many hobbies, all it takes is the actions of a few idiots to damage the reputation of the overall activity. Hopefully the public will see the legitimate uses, along with the enjoyment hobbyists have been having for years, and not initiate bans where they are not warranted.
Why are you calling it a drone. Can it fly without your input? No it can't. Can you set way points? No you can't. It's people like you giving our hobby negative attention. Quadcopters are not drones unless you build them that way. Your flight controller is a kk board. It won't fly without with out your radio commands. I don't want people thinking my quadcopter is a drone.
hey +MrArmagedd0n, great video! Can you tell me where you got those landing blades located on bottom of each arms. Looking everywhere for those. Thanks. :)
I have f450 and almost everything seems ok. My problem is that the lever on tne transmitter are switched, im right handed and my throttle and yaw are on the right hand so it's wrong. do you know how to switch the sticks? Thanks. P.s. VERY much a newbie first build kk2.15 and fs i6 remote.
Thank You!! I use your demo about a year ago and refer to it when I build my quadcopters. Still learning the dynamics of the KK2 board as well as the flight controller. Again Thank you!!
Wow you did a good job explaining the setup of KK 2.1 board. Had to be one of the clearest videos on setup of one i came across. I used Naza and Apm and Pixhawk the KK is a brave new world for me lol!! For the life of me could not find a simple example of esc tuning for the KK till this video!
Thank you very much! Before I found ur vid I couldn't get my quad to fly without wobbling.
What transmitter and receiver are you using?
Hi! At 11:00 mine is reading much higher values. When i arm my quad the motors start running. Is it the KK2.1 or the Turnegy 9x that does that?
Adjust the trim settings on your 9x until they read as "0" on the KK2.1 screen.
MrArmagedd0n thank you for taking your time to answer my question! This is a great video guide !
Can you help me? I have a safe transmitter and it won't start on full throttle, it tells me to turn it down before it boots. How can I calibrate the ESCs?
Great video, but how did you power the led's for night flying?
These particular LED strips use 12v, so I hooked them directly into the power distribution board.
Hey love your channel and have been coming back to this video to troubleshoot my kk2.1 board. I wanted to ask how you wired the voltage metre. Have you gone from the battery connector to the voltage metre to the pdb?
dooseyboy, I no longer have this particular flight controller, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
New to diy quad pardon what may seem like dumb question but with opto esc's am I removing both the + and - off the esc wire and replacing with + and - from the bec wire to power the kk2 at m1 pin
hi joey here, so what mode are you using hell mode or airplane mode or?
How long is your feet extender? is it 4 inches?
They are 4.5in overall, and lift the original "feet" an additional 3.75in off the ground.
What FW ver are you on? I have a KK2.1 and factory reset has HW ver 2.15 and FW ver 1.6. Thanks for the video.
I am currently using the firmware created for the KK2.1 by Steveis over on RC Groups. I am using the "Lite" version which is more for beginners. The firmware is called: KK2V1_1V17S1Lite
I like the feet you have on there. Where did you get them, I keep going through lame landing gear and those look pretty cool.
They are carbon fiber, and the set of 4 cost me around $35. The link I had saved is no longer active from RC-Drones where I purchased them. They work and look great, but I recently had to replace them because my new gimbal didn't have enough clearance. I will post an update soon showing the new ones.
Aliexpress.com search for "CF DJI LANDING GEAR" 10$ for set of 4
Does this work with PWM transmitters?
I,ve been watching a few videos on programming za kk2.1. Why would you have channel 5 for shutting off flight stabilization? I mean, wouldn’t you want it on all the time?
Followed your setup the letter and she flies though a bit twitchy compared to others I have. I do not have GPS on it yet though. One thing I noticed is I can do a CCW funnel with no problems, but CW is very wide and not able to complete the instruction. Is there some setting I need to correct.?
Great "how to" video. Question about self level settings. How do I give myself more control and less to the quad like for better bank turns. I am more of a sport flyer rather than FPV or video.
+jerry zito , I was running the Steveis KK2.1 Firmware that is geared more for beginners and / or slower reaction for use with a photography platform. He also offers a "Pro" version of the firmware which is much more responsive and better for stuff like Acro. Search for "Steveis KK2.1 V1.19S1 Updated Firmware".
ok thanks
Nice video, thumbs up. Cheers from sunny Sint Maarten
what size and cell lipo are you using?
hey +MrArmagedd0n, great video! Can you tell me where you got those landing blades located on bottom of each arms. Looking everywhere for those. Thanks. :)
I didn't buy them from this site, but it is the same product. May find it elsewhere for less $.
drone-quadcopter.com/shop/drones/phantomount-carbon-fiber-landing-strut-extensions-for-dji-flamewheel-450-or-550/
That is a very nice setup.
May I ask where did you get the landing skid Extension? I was checking on aliexpress and ebay, but I could not find one. There are other types, but I like the one you are using, I believe it will give the quad the best stability by landing.
Ranger80pl1, the place I purchased them no longer stocks the extensions. This site seems to have a very similar product, but a bit more expensive than what I paid.
www.phoenixflightgear.com/Phoenix-Flight-Gear-F450F550-Flame-Wheel-Legs_p_15.html
Thank you for the link. It is expensive indeed. A bit too much for a part as simple as a copter landing gear. I believe I will need to check for other options.
Hello.
I have a little question.
I have KK2.1.5 flight controller and speed controller 4x RC Simonk 30A ESC Brushless Motor Speed Controller for Multicopter BEC 5V / 2A.
To connect them have I disconnect the plus wire from BEC in M2-M4 connections and leave plus just only in the M1, or can i connected regular without disconnect anything (3 wire from BEC to controller )?
Thanks
Alex
Greetings! Nice video. I am having troubles figuring out how to power the board. If my speed controllers have BEC's, then I plug them in like normal and let speed controller 1 power the board, but then clip the power leads on speed controllers 2, 3,& 4 so it doesn't get over powered? Or do I just plug all speed controllers in like normal? I am using the board for the HK 250 quad copter and i am using all stock component. I would greatly appreciate your help. Thanks
Good question. Clipping is not needed on the remaining escs. The board simply does not use them.
Hi I have a question about the 9XR pro that you are running
What reciever are you pairing it with? Im looking for a TX RX and im leaning twards the 9X with the 9X and 8channel RX from Hobby King, Your video REALLY helped me set up my SK450, now im looking to start upgrading.
Thanks for sharing!
+alien4fish , I was using the FrSky V8FR-II 2.4Ghz 8CH Receiver (HV), with the FrSky DJT 2.4Ghz Telemetry Module.
Outstanding! I just ordered the the Taranis plus combo fro Helibatics and it shipped today.
But im having a HELL of time trying to get my SK450 to fly right, It seems to want to gyrate around Not stable and it flipped over on itself.
Hopefully the Taranis and new reciever will help.
Thanks for the response and taking the time to post up this video, Happy New Year!
+MrArmagedd0n Friend, I want'll make a tricóptero t3, I will use the radio Turnigy 6x FHSS with KK.2.1.5. I can calibrate the esc this anyway ??? if I remember correctly, I should put the stick in the maximum, connect the battery and then the esc 2 beeps slow down the stick? also would work I calibrates one esc to see using just the receiver?
+Raimundo Vieira, I sold my DYI quad and purchased a 3DR Solo, so if the answer isn't found in one of my older setup videos, I really can't be of much help. Sorry.
Is the ubec a requirement with the kk2 board and 3s lipo?
Not required, but is a good idea to use one.
What kv are the motors? Also what props are you using? I built a quad w/ a Q450 (knockoff of DJI board.) I like the video, but when using your PI settings my quad flipped twice. The P was way to low. I'm using 1200KV brushless motors w/ 10x4.5 props. Decided to do a bit more research on PI settings before I try any more and found out that too low of P setting can result in a quad that can flip in autolevel mode. FWIW, I double and triple checked the controller, motor direction and props and everything is correct, it will get up in the air and try to stay stable, but as soon as I start to bring it back down it wants to flip.
TAZ427 Not sure what would be causing it to flip. I no longer have this particular quad (sold it), so can't help much with troubleshooting. As far as the motors go, whatever come with the original DJI Flame Wheel F450 Kit, is what I was using on this quad. Good luck.
You sir helped me out a bunch! thanks for the video
How u connected your flight control board to recever from which wire, plz tell me fast
HI, Thank you!
Two questions: How do I know the numbers in the P1 Editor ( gains) , you said we have to experiment, what about setting up for the first time?
None of my ESCs have BEC, using external BEC, Do I plug it into the RX? (aux), afraid I don't know how to make a modification like you. What do people usually do in this case.
Thanks in advance...
Do you know how to set the 45 deg. offset to fly in X on frames that only have mounting holes setup for + config.?
The board must always face forward and there is no offset functions that allow the board to be mounted at a 45 degree angle.
teamscreem Not true. Have a look in Misc Settings. Ref: dl.btc.pl/kamami_wa/hk_54299_7.pdf
Thought we may have been talking KK2.0, I could not find it on mine with V1.6 firmware. You could also mount it at 45 degrees and use either the X or + motor layout for + and X respectively to use the 45 degree offset build into the board. Always more than one way to skin a cat. Thanks for the link to the latest setup instructions, they are very informative and I may use them one day if I go back to using the KK2 boards.
teamscreem Oh, I just assumed that with the latest firmware the KK boards would be the same. Bit silly when I think about it since the different KK boards have different hardware and thus the firmware can't be the same. I can only speak for the 2.1.5 (which does have the offset feature), but I would assume the 2.1 also has that function.
which type of wires are you using to connect thee kk to the receiver
vineet yadav Using standard 3-pin connectors, with 22AWG servo wire.
What battery do you have and how long does it last with a go pro?
Turnigy 3600mAh 3S LiPo. I get around 9-11 minutes flight time depending on how hard I am pushing it.
Thanks for the help!
Thankyou sir, this type of parts where is purchase, please send the details
nice vid!!!
i have the same problems with the rud/yaw. i can not find on my turnigy 9XR the menu reverse.
my version is:
V1.127
08-04-2015
er9x-r817
hi can you list down all the electronics' specs you used in this project? thank you!
Is there a camera
Good old times! Hobbyking was still a thing, drones weren't configured in a browser.
Thanks! I have a HEX but only three of the motors spin up once I've gone through everything. Swapped wires around but no luck. (The problem motors seems to sort of vibrate/get stuck).
Any ideas on what to look at for this?
Thanks brother! Just ignore the negative comments. We got better things to do.!
do u need to connect osd to flight controller ??
I am not using OSD on this particular multirotor, but yes, it would typically plug into the flight controller.
i think i searched the whole youtube on how to connect osd to flight controller and i cant seem to find one can u please link to anyone thnx
blackdedo93
I don't have any links for the KK board, but search "Minim OSD Quick Installation Guide", and you will get tons of pictures / wiring diagrams showing the setup for connecting an OSD.
MrArmagedd0n
well what i mean that in almost all vids they use the osd alone without flight controller
and thanks for replying so fast :)
The "bye papa" was the best :)
What firmware of the kk is that?
KK2.1.X V1.17S1Pro firmware by Steveis
Can I Attach 30A ESC directly to the kk 2.1 board with 11.1v 2200mah battery. .?
Do I need to use BES for my quadcopter. ?
which wire should I use please tell me for the connection of kk 2.1.5.
You seem knowledgeable on KK2. Not looking for speed, just more maneuvering control.
Do I need that control board
hi, I am using KK 2.1 all setup seems correct but when I increase the throttle with prop installed it disarm automatically. But when it is without prop it works
Can you fly quadcopter with fs ct6 and kk2.1.5 flight controller
Hi, I am kind of stuck with this thing. I have connected it all and in safe mode all seems to be fine, in this radio test option, the controller does recognize all the sticks and is showing values when I am moving them, but after arming it, the only thing which seems to be functioning correctly is the throttle - it lifts off and lands - but that's about it. When I am trying to move the sticks like rudder, or elevation, to move the model in the air, nothing is happening. I did a test without the propellers and there was no change in engines speed when I was moving the right stick. Would you know what could be the cause of this?
solved. stick scaling was set to "0" i the not working cases. :)
I no longer have this particular flight controller, so I'm afraid I can't help troubleshoot. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help.
i have a st 360 quad with kk2.1 . in my tx when i just give 1 percent of throttle it goes to the max level what can i do
Funny to read some of these negative comments from people that are butt-hurt that I mention the word "drone". Maybe they have ample time to waste crying over semantics, but I sure don't.
+MrArmagedd0n You were nice enough to take time to help others set this thing up. I for one completely respect that and appreciate it as I just got one of these in trade and want to make sure it's set up right. Thanks again! And the trollers can go suck it. Let them go have a Drone/Quadcopter debate, We'll be out flying in the meantime lol.
lol the only difference is if it has a gps or not, not a big deal
MrArmagedd0n which motor are use
hi,why don't work receiver test? please help
nice video, too.
Great video!!!.. Helped a lot..
hi. KK 2.0 Work volts? Thanks
my kk2.1 self -level is no but it not armed please help me it is my college project...
I no longer have this particular flight controller or quad, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
hi. can you help please. how can i change between default Misc. settings to Misc. Settings 2 on screen? is it possible to do without usbasp - cause i have just the board. may be pressing buttons))?
Iron Man , I have sold this particular setup, so don't have a way to test for you. Sorry.
np man. resolved this issue/ thanks
Dear you like expert could you help me to setup qq super flight control with radio link At9 actually I done all connections but all motor is not spinning in the same time only spinning 2
hai sir,can you share me your setup?such as pi editor,stick scaling,misc set,self level,mixer editor...im new to this hobby sorry...hope you dont mind to share your setup :)
Hello sir .. can you please help me out with my quadcopter .. i have done evrything right i suppose and trying to do the calibration but the motor just didnt start .. it starts only while i push the 1&4 buttin together and i tried calibrating them individually but still not able to fly my quad please help sir.. i am in a mess ... i am using tranmistter fs ct6b and kk board 2.1.5
+Rohit Chauhan , I no longer have this particular flight controller, so can't test anything for you. Best bet would be user forums / communities dedicated to Quadcopters like DroneFlyers, DYIDrones, RCGroups, etc. Good Luck.
My drone started to give me a red dot on the revivers. Its usually green. What should I do to fix it. Its still flying but not as well
I have never seen a red dot. Can you be more specific as to where it is appearing, and what you are doing when it goes red?
Help! I cannot get mine to arm? Just started doing this, can't understand why? I have checked and rechecked everything. The receiver is getting signals as the KK2 is reading them in the receiver test menu so I am stumped?
Not sure what is causing your issue. I no longer have this particular flight controller, so can't be if much help. Recommend heading to RCGroups forum as there are many active KK2.1 users that can help you out. Good luck.
+MrArmagedd0n well thank you for replying anyway. I'll check there
hi , could you please hep me configure my kk2 and esc , I just couldnt get it going after multiple tries .Thnax
Hi do you know what is wrong with mine, because they all spin at different speeds and one of the motors is scorching hot!😕
Cameron if the motor is getting scorching hot that means there is impedance so something is wired incorrectly which is causing the voltage through that motor to be too high
Without seeing it I can't advise but Totum hobbies should be able totalk you through how to wire it if you go down and see them. Love you son oh one point check the soldering to make sure there is no bleed of solder across contacts that would lead to faulty circuit and prevent the board working.
Dude!! Very Helpful! Thanks
my kk 2.1.5 board says pass through mode and then goes to the main screen, the screen before menu
A great guide.
Can you help me with mine can’t get it to work
bobby Puopolo, I no longer have this setup, so can't really help troubleshoot. Sorry.
nicely done, thank you
So helpful, thank you!
when i connected receiver to kk2.1.5 why receiver is blinking without Tx ON and show yaw input error plzzz solve this problem
satendra singh tripathi yaw input error indicates that kk board is not getting any yaw signal from tx. its normal as when tx is off it does not gives yaw or any channel input. when u switch on the kk board with tx on the error screen will be gone
There is a ghost at 14:11!!!! Watch after motor spin u lol!!!!!!
My quadcopter is not stable Help me
I no longer have this particular flight controller or drone, so I can't really help troubleshoot anymore. Your best bet would be forums like RCgroups and DYIDrones, since there are active users with the KK2.1 that can help. Good luck.
I meant self leveling.
Thanks a lot!!!
Good sir
Your calibration is not complete, you need to keep pressed bottons 1 and 4 until you lower the thtrottle and ear the last beep from ESC.
Ha
flight controlled
States are making laws to ban drones, not rc aircraft. If people like you trick the public into thinking that all rc aircrafts are drones they will ban our hobby. But that just won't sink into your head. Call it what you will. Your part of the growing problem
Most of the states (like here in Colorado) that are looking to initiate bans are specific to large game Hunting/Scouting. For that purpose, I completely agree that rc craft should not be allowed. If you did some research and actually read the language of those bills, the do not call out "drones" specifically, but also refer to them as "UAV", "UAS", and even "RC Aircraft" calling out the ability to take pictures or video while in the air as what constitutes the ban for Hunting activities.
So again, semantics. It doens't matter what they are called, it is the ability for aerial survailance that some people (and the bills banning their use for certain activities) are worried about. The "growing problem" is not what people call these craft, it is accessibility. Since it is becoming easier for people to purchase and operate these devices, we are seeing a individuals doing stupid things with them (like flying close to airports, or snooping in people's windows). Unfortunately like many hobbies, all it takes is the actions of a few idiots to damage the reputation of the overall activity. Hopefully the public will see the legitimate uses, along with the enjoyment hobbyists have been having for years, and not initiate bans where they are not warranted.
Why are you calling it a drone. Can it fly without your input? No it can't. Can you set way points? No you can't. It's people like you giving our hobby negative attention. Quadcopters are not drones unless you build them that way. Your flight controller is a kk board. It won't fly without with out your radio commands. I don't want people thinking my quadcopter is a drone.
+Nathaniel Richardson or just stop whining? i dont know
+Nathaniel Richardson drone-
Dynamic
Remotely
Operated
Navigation
Equipment.
A toys r us rc helicopter can basically be called a drone
hey +MrArmagedd0n, great video! Can you tell me where you got those landing blades located on bottom of each arms. Looking everywhere for those. Thanks. :)
Please tell me what do you connect at the voltage monitor port on the left. Thanks.
if i use 4 channel transmitter then the binding is same as 6 channel transmitter?
How did you manage to pair a turnigy transmitter with an fr sky receiver?
I have f450 and almost everything seems ok. My problem is that the lever on tne transmitter are switched, im right handed and my throttle and yaw are on the right hand so it's wrong. do you know how to switch the sticks? Thanks. P.s. VERY much a newbie first build kk2.15 and fs i6 remote.
Auxillary is 'off' how do i turn it on? I've connected channel 5 to Aux
iam using kk 2.1.5 for building quadcopter.but here is a problem that is when iam trottle up my motor has stop running.pls solve my probelm
Mentalz House Balance your propellers.
but how?