KK2 1 5 FLIGHT CONTROLLER SETTINGS

This video describes how to set up KK2.1.5 Flight controller board for a QUADCOPTER
QUADCOPTER ASSEMBLY Video :
• QUADCOPTER ASSEMBLY
FLYSKY LCD Model BINDING :
• FLYSKY BINDING Tx With Rx
FLYSKY CONFIGURATION :
• FLYSKY SETUP MADE EASY
BLDC Motor direction setting :
• QUADCOPTER SETTING BLD...

[@antonyansonv]

Thank you so much for this video, it helped my son to make his drone to work.

[@dronepilot260rc]

Thank you so much for your expertise and time!

[@aviationdesigns_mg7883]

This video was really helpful

[@BalaSai79]

Nice sir very clear expiration, keep doing like this videos 🥰

[@roland3138]

thank you for your good explanation, greetings from the Netherlands

[@vaishnavk9156]

Really useful video sir

[@fastlifemedia7453]

Nice video good explanation

[@electronic7979]

Very good 👍

[@karthie003]

I'm Karthi, I used to come by your store, remember? Anyways Great video.

[@abhiflute2023]

Sir can K.K 2.1.5 be used for 2-3S micro builds using 6-10A ESC and 1104/1106 motors?

[@badspike319]

thanx boss...

[@excellenceinanimation960]

Question, What is the red port marked batt? Is it where I can plug in a Battery?

[@mlacreations3219]

Tq Sri🙏

[@audenlenhares1188]

Where did you get the special 3 section wire

[@satyapatchigolla8300]

I was getting a blank screen on the Led screen just the Led light is glowing. No other things is viewed in my screen what is ur suggestion .please

[@Mevenki]

same settings applied but in the real world my quadcopter not balancing
can you help me out

[@vinayss1544]

Hi,
I have purchased two KK 2.1.5 FC board. Both the boards are not getting connected properly and all the controls shows NO SIGNAL. CAn you kindly help me out with this.

[@sangarp2001]

you powering the kk board with 4 esc. it it OK? in APM pilot only 1 of the 4 esc is used. Other 3 esc do not power the board,only ground and signal is connected.

[@parthacodes5893]

Don't know why but my bldc are not rotating just beeping

[@khalidwa1]

I followed your instructions and got "no yaw input". I ensured my transmitter was on before the copter. I tried factory resetting the controller. Any suggestions?

[@AKSHAYMISHRA14]

I am getting the same error. Did you get any solution to it ?

[@omanabhasi5787]

Can you tell me what battery is used

[@basavarajnarthi2575]

i followed every step but i cannot arm my quadcopter what should i do?

[@shankermudigonda8563]

Want to know the supply where was to give to board.

[@aksdiyprojects1999]

Good tutorial। Has a prob with self level mode। Unable to set it on, with either aux or stick।
Solution pls

[@sudeephari253]

Saravanan please help me in setting up my new quadcopter.

[@technomediadailylife3545]

But sir my drone is arming by presing right side ??why ??

[@sukumars3022]

If your shop was opened today?

[@saifalikhan7692]

Sir please solve my problem my kk2.1.5 flight controller display is blank pls tell me the solution

[@meeniga.dolendravamsikrish285]

Can I make a drone with out flight controller????

[@KRISHNAHS]

Sir mere khana hai ki mere kk215 men sir more setting me kaval aux and strike hia allwase nahi aa raha hai plz madat kijiye sir

[@selvakr7]

Please help me I am getting blank white screen

[@untamedartist4948]

Where did you get the one to three female to female wire?

[@fortunemcdoodles3529]

You can buy from amazon

[@israoc]

my ecs do not maintain the same speed that can be

[@abhisheks9093]

If we follow your video completely will it work for 100% ??.....................Please do tell

[@pankajkumarbishnoi1847]

Can I use kk board for self belance robot..?

[@amalraj1879]

No bro only for drones and plane

[@vivekduggal987]

Sir apne bettry ko kha per connect kiya he

[@KRISHNAHS]

Sir aalwase nahi aa raha hai mera drone ek traf bhag raha hai sir bataiye kyo bhag raha hain ham presan hai sir plz

[@sunilsalawitya5568]

Ud nahi raha hey dron setup kaerne ke bad bhi kya kare sir

[@amit22joshi]

Nice Video...are you on instagram?

[@LeastKnownFacts]

Hi hope you are doing great. I setup my quadcopter with same configuration mentioned by you. However my fourth motor is not rotating. I connect the same motor with output channel 3 then it's rotating. So in nutshell my fourth output channel is not working. Can you help me how to make any configuration for this?

[@vaishnavip4998]

Hi i followed all the instructions exactly same. But drone is not taking off. The motors are running well. But y drone isn't taking off??? Can pls someone help me with this.

[@amalraj1879]

Check whether you fixed propellers correctly

[@dharmi5858]

By my mistake I run the motor using propeller and it's cut my 1 fingers 😭 badly

[@sushmamahadik379]

Hi. Actually i have done the same as you have said in the video but yet their is a arming problem with my drone. Can u help me?

[@basavarajnarthi2575]

did u solve it if yes how?

[@tusharbhardwaj1955]

Same bro plz help 😢

[@rohithreddy3814]

My kk 2.1.5 is not arming

[@mohansingh7131]

did u find the solution

[@makamthribhuvan4189]

Same problem

[@tusharbhardwaj1955]

Same prblm

[@tusharbhardwaj1955]

Help plz bro 😢

[@Vkcreation3024]

Hlo help me sir

[@Vkcreation3024]

Argent

[@rajureddy6791]

Sir please help me to solve my problem , I do as same ur done in this video but in my drone ARMED not happen .

[@rajureddy6791]

Please help me sir

[@tusharbhardwaj1955]

Bhai armed hua toh bta de bhai kesa hua plz help bro

[@mdsumon-db6gr]

ভাই ফ্লাই কন্ট্রোলার টা কত টাকা

[@mdsumon-db6gr]

আপনার কাছে কি আছে

[@m.babaee1260]

باز نمی شه

[@808tui]

...............lol!!!!!!!!

[@nilakshrana8044]

Bhai tera scren me kya ho raha h..kuch dikta nahi... chasma bhi lagaya phir bhi kuch nahi dikhai deta.. achha camera use kar

[@ahbaghdoooohootojecislomeh7148]

Fake