dear sir I am making a drone with 4 motors with KK 2.15 flight controller and three motors are running at good speed but one motor that is starting motor is running at more than speed how can I control the speed of first motor please help me sir
Follow these steps. Before these steps calibrate the each and every ESC's separately using Tx and Rx. Then Connect with the KK board. 1. Switch on the Tx and raise the throttle to maximum. Press and hold first and last button of Kk board. 2. By holding them connect the battery. 3.you get throttle pass through on the screen of kk board wait for some time and decrease the throttle. 4. Disconnect the battery. 5.Again connect the battery.
@@techathome thank you sir for your information it's very informative I am really thankful for your suggestion I have watched your videos more than 50 times your videos are more informative and useful thanking you sir for your reply to me all the best for your future videos
When its got armed and trimming up the throttle stick only one or 2 are rotating and again it displays safe and again when i armed same thing is displays
Sir, after doing ecs calibration All motors not run at same rpm what should we do now? and quad goes in one direction highly unsatble all the reciver test has been done . and acc callibration too..bt after esc callibration all motors nt run at same rpm
Remove all the ESC'S. Calibrate each and every ESC separately using the transmitter and receiver. Then connect ESC'S to flight controller and calibrate ( similar to what I have shown in the video)
1. Remove the battery from the drone. 2. Switch on the transmitter. 3. Press and hold the first and last button of the KK board simultaneously and then connect the Lipo battery to the drone. 4. After 2 minutes remove the battery. 5. Then connect the battery and try to fly.
@@praveen6740 Have you calibrated the ESC individually and by using flight controller ? Follow these steps. Before these steps calibrate the each and every ESC's separately using Tx and Rx. Then Connect with the KK board. 1. Switch on the Tx and raise the throttle to maximum. Press and hold first and last button of Kk board. 2. By holding them connect the battery. 3.you get throttle pass through on the screen of kk board wait for some time and decrease the throttle. 4. Disconnect the battery. 5.Again connect the battery.
my kk board goes to armed but after 5 sec it goes back to safe like when i connect 3 motors it is working fine but when i connect 4 motors it goes from armed to safe in 5 sec and only 3 motors spin (all 4 motors are working fine individually) i did everything i could tried calibrating motors one by one and all help me please
Follow these steps. Connect all ESC'S with the KK board. 1. Switch on the Tx and raise the throttle to maximum. Press and hold first and last button of Kk board. 2. By holding them connect the battery. 3.you get throttle pass through on the screen of kk board wait for some time( it gives some sounds) and decrease the throttle. 4. Disconnect the battery. 5.Again connect the battery.
@@techathome i did do those steps like i calibrated motors i tried doing them individually also but it dosent work ,only 3 motors work when i connect 4 th motor it switches from armed to safe in 5sec
Do i only need tuning in flight controller or have to do settings in remote as well?
Only in Flight controller
I am facing the problem on selection settings on fcu bord could you pls help me
dear sir I am making a drone with 4 motors with KK 2.15 flight controller and three motors are running at good speed but one motor that is starting motor is running at more than speed how can I control the speed of first motor please help me sir
Follow these steps.
Before these steps calibrate the each and every ESC's separately using Tx and Rx.
Then Connect with the KK board.
1. Switch on the Tx and raise the throttle to maximum.
Press and hold first and last button of Kk board.
2. By holding them connect the battery.
3.you get throttle pass through on the screen of kk board wait for some time and decrease the throttle.
4. Disconnect the battery.
5.Again connect the battery.
@@techathome thank you sir for your information it's very informative I am really thankful for your suggestion I have watched your videos more than 50 times your videos are more informative and useful thanking you sir for your reply to me all the best for your future videos
When its got armed and trimming up the throttle stick only one or 2 are rotating and again it displays safe and again when i armed same thing is displays
And mite over i had changed my kk2 board to new one
Bro from where we buy pwm wire
Where I fixed camera
When I give full speed, the motor stops. Even if one motor is rotated but the other motor beeps sound.plz explain????
Do ESC calibration and throttle pass through calibration
Transmiter and receiver ko conect kese kare or kab kare...??? Esc lagi honi chaiae motor ke sath...??
Serach for Binding Tx and Rx Video, bro, I have not done that video,
No need to connect Motor, only ESC need to connect with Receiver
@@techathome same kv and t ki brushless motor ho but company change ho to kuchh issue aa sakta...!!!
No, KV rating is same, then no issues
Home made drone keliye license ki jarurat padegi...!!!
No, but not to fly in public places, take it to ground!!
Sir, after doing ecs calibration All motors not run at same rpm what should we do now?
and quad goes in one direction highly unsatble all the reciver test has been done . and acc callibration too..bt after esc callibration all motors nt run at same rpm
that y it goes in one direction due to motor different rpm.sir please seuggest me'
Remove all the ESC'S.
Calibrate each and every ESC separately using the transmitter and receiver.
Then connect ESC'S to flight controller and calibrate ( similar to what I have shown in the video)
Change yours lipo battery.bcz this problem was also happend with me due to weak battery.so then i changed my battery and my copter was stable then
Not running in same rpm.... separately calibrating ecs ...but no improvement ....give some idea bro
1. Remove the battery from the drone.
2. Switch on the transmitter.
3. Press and hold the first and last button of the KK board simultaneously and then connect the Lipo battery to the drone.
4. After 2 minutes remove the battery.
5. Then connect the battery and try to fly.
Have u used power distribution board ot not..??? How
robu.in/product/multirotor-esc-power-distribution-battery-board-quadcopter/?gclid=CjwKCAiAkrTjBRAoEiwAXpf9CcIgfwZm30TGJVF_Q2X9nt2kA3lUyvfeS6Q6WcfOj7WPd6HTjZS1BRoChO8QAvD_BwE
Amazon: www.amazon.in/INVENTO-Multirotor-Distribution-Quadcopter-Multi-Axis/dp/B071FSX3S5
U ordered the remote from banggood??....Cause i think the customs wont let the radio to enter the airport for shipping
If you select India Direct Mail as shipping method it's free of customs and there are no issues.
@@techathome So basically we can get custom free shipping .....i live in ghaziabad...UP
@@sambhavsirohi3294 yes
How to setup the transmitter
Please tell me I don't know pi setting I set the value 70 50 40 30 but is not stable. It is not in one direction
You have not calibrated ESC's .
Bhai mere me self level me aux aur stick bs aa raha hai always nhi aa raha hai plese help me
Factory reset the board and check once.
Sir kk board mai wifi camera kaise add hota hai !! Plsss tell
I think you can't Add to KK board
You have to use some action camera externally
How to connect the cables of esc and receiver to flight control board
ruclips.net/video/yISwnTMTANY/видео.html
i have done same thing in the video but didont get armed please help!!!!!!!!!!!
Try to arm in opposite direction and check (towards left side)
i did it all the side but still not armed
how can I attach thermal sensor in it?
Kk board is very basic, i don't think this will support
Hey how do we reset the receiver?
Well... Kk 1.2.5 can program to gps rescue mode?
You cannot use GPS in KK board.
Mode setting me self mode me aux or stick ka option hi aa tha hai always ka ni aa rha or receiver test me armed ka option hi ni hai
My Quadcopter is not getting armed 😭 bro please help me bro🙏
Try to arm in opposite direction
( Rudder towards left direction )
Nice
Bro one of the four motors in my quadcopter is spinning slowly. What to do bro. Pls help
Either problem in the ESC or Motor I think. Try changing those.
@@techathome bro individually each components works in a good manner but after connecting to the kk board there is variations in speed of the motors
@@praveen6740 Have you calibrated the ESC individually and by using flight controller ?
Follow these steps.
Before these steps calibrate the each and every ESC's separately using Tx and Rx.
Then Connect with the KK board.
1. Switch on the Tx and raise the throttle to maximum.
Press and hold first and last button of Kk board.
2. By holding them connect the battery.
3.you get throttle pass through on the screen of kk board wait for some time and decrease the throttle.
4. Disconnect the battery.
5.Again connect the battery.
@@techathomeAlready I had done all these steps.
Then replace the ESC, even I had same problems. It was working well individually, but not with KK board.
mode setting me safe mode me aux and stick hi aa raha hai always option nahi aa raha hai
Bhai factory reset krdo . phir ek baar check kro
My drone rotates automatically to the right(rudder), what should i do.
Does it rotates to the left when you press the Rudder to left side??
@@techathome no it automatically rotates to the right
@@abhishekabhishek7967 Change both the ESC's of the motors rotating in clockwise direction.(Motor 1 and Motor 3)
@@techathome ok, can you plz give me your some contact information so i can contact you. Just need some guidance.
Great 😘😎☮
Sir my drone armed but motor not rotating
Have you calibrated the ESC'S
Hello sir plese help individual 9369229750
Sir what is your whatsapp number
You can contact through Instagram
(Link in description box)
Hlow sir plz kk2.1.5 hexacoptor video programming
Follow the instructions in the video. In the frame type select hexacopter type frame .
gps kysa connect karanga
No GPS option in KK board,
U have to go for APM
Always option nahi a raha
That's not a problem I think
Kk2.1.5 arming but do not spin motor
Cliberate every ESC's
Mera bhi aise hi hua tha
Tech at home bhai apkeesc me kon sa capaceator laga hai 25v.......uf
my kk board goes to armed but after 5 sec it goes back to safe like when i connect 3 motors it is working fine but when i connect 4 motors it goes from armed to safe in 5 sec and only 3 motors spin (all 4 motors are working fine individually) i did everything i could tried calibrating motors one by one and all help me please
Follow these steps.
Connect all ESC'S with the KK board.
1. Switch on the Tx and raise the throttle to maximum.
Press and hold first and last button of Kk board.
2. By holding them connect the battery.
3.you get throttle pass through on the screen of kk board wait for some time( it gives some sounds) and decrease the throttle.
4. Disconnect the battery.
5.Again connect the battery.
@@techathome i did do those steps like i calibrated motors i tried doing them individually also but it dosent work ,only 3 motors work when i connect 4 th motor it switches from armed to safe in 5sec
@@techathome is that the only solution you have ?
@@gnaniharsha9589 yes, I also had the same problem initially, but worked for me.Try replacing ESC.
@@techathome all esc are working fine but i cant see rx symbol in the remote
This is rc drone
Not working still
Sir i connected how you done then also still backlight is their...
pls help me
Ok
Fali conto kk 2.1.5 setap hindi video
Me moh shanavaj mera quadcoptar start ni hora plzzz plzz sabhi setting hogai armed ni hora plzzz plzz sabhi kk2 6t6b 6chenal 7417892701fho btao mujhe
Try to arm by positioning throttle stick towards left.
Nice