HobbyKing KK2.1.5 Setup

[@alwaysbehappy8662]

Thank you very much

[@MrRui33333]

bom video, mas no entanto uma das maiores duvidas de muitos é a fiaçao, cabos e receiver , por isso, se um dia quiseres faz um tbm mais completo sobre a ligaçao ate a calibraçao, mas ainda assim esta muito bem e mereces os parabens por teres esse gosto de partilhar

[@danielpetterssons]

thanks!

[@thibaultdekock8077]

You are my hero today

[@sairajnsr6143]

Hi ,
Plz give me solution for my quadcopter. After the arm all motor are spin at once but it doesn't moving up or forward
Plz give me solution for this one

[@SachinDevkota]

What can i do my microcontroller kk2.1.5 diplay apear blank please give me any idea

[@alfacraft]

hello.. i have a problem with my MINI KK (2.1.5FW).. after arming it short beeps 10 times than auto-disarms.. but if i push the throttle the motors start spinning normally.. is there any issue?

[@baleallout4172]

You have the only good video on how to set up kk2

[@pavankarlakunta4568]

i am having problem with my hexacopter. when i gave full throttle it is not moving for required altitude but is pitching highly. please tell me PI gain tuning for hexacopter

[@danielpetterssons]

+pavan karlakunta
I'm not entirely sure if it's right, but try this
For pitch and roll- P Gain-80 P Limit- 100 I Gain- 60 I Limit-20
You can leave the rudders numbers stock

[@stevenathandesa208]

Great Video.
When I follow d steps and when it comes to d last step of arming,
My kk 2.1.5 dosent' Arm.
What could be d problem?

[@danielpetterssons]

i think there is a auto disarme in the settings look for that maybe

[@gnaniharsha9589]

my kk board goes to armed but after 5 sec it goes back to safe like when i connect 3 motors it is working fine but when i connect 4 motors it goes from armed to safe in 5 sec and only 3 motors spin (all 4 motors are working fine individually) i did everything i could tried calibrating motors one by one and all help me please.

[@Ajaysingh-li1dv]

my drone is running automatically after arming, and one more problem is that in my kk2.1.5 flight controller in receiver test setting all values are not set to zero by the transmitter trims tell me what i do for fixing these problems

[@janspoelstra8309]

Setting the sticks to zero is done in the sub trim setting of your transmitter.

[@anjansigdel9464]

Whenever i start to calibrate the esc one motor is beep to fast for a longer time and after calibration only 2 of motor spin at a 25 % of

[@darpanbashyal1597]

and bro we have to do any transmitter setting in our remote control or nt plz answer it...?

[@Anonymous-uf1gi]

ey admin I'm having a trouble in starting my quadcopter. when I rise the throttle the motors doesn't spin till I push it to the middle then one after an other motor stars to spin can u plz tell me what's the problem with it

[@marianohernandez198]

can you please tell me which receiver is that on the quad..what model

[@danielpetterssons]

+Mariano Hernandez 1
dsm2 dsmx orange receiver
www.hobbyking.com/mobile/viewproduct.asp?idproduct=46632

[@kazz-mann5580]

Hi, Thanks for the Vid, I really like this kk2.1 easy programing But I have 1 Q? The JST battery plug in on the board. Does and should that plug into my main battery? because I cant get my voltage alarm to go off and I notice on the board its not reading any Voltage?

[@danielpetterssons]

Hi Kazz- Mann
yes u are supposed to plugged the main battery direct to the board and then go in to Misc settings and change the alarm voltage to 105 (it you are using a 3s lipo)

[@Elociuss]

love u daniel

[@danielpetterssons]

nemen tack fiLip

[@ShahbazKhan-mj1vi]

hi could you tell me if the pi settings u are using are ok to use with a zmr250 mini quad? thanks in advance

[@danielpetterssons]

I don't actually know. But you can always try to use the pi settings that I'm using.

[@progettoaladino]

DANIEL FOR A DRESS 250, WHICH SETTING NEEDS TO DO

[@Elociuss]

wow

[@shubhampant5172]

I have a remote MODEL- FS-CT6B, its 4 channels are working which are aleiron, elivator, throttle and rudder, but its auxilary( 5th channel ) and 6th channel are not working, i have connected only four channels to the kk 2.1.5 board and do as you do at the video, but its not working.

[@danielpetterssons]

+Shubham Pant
you will see The Channels if u lock under The kk board, and yes auxilary is Channel 5 u dont need ch6,!

[@danielpetterssons]

+Shubham Pant
But what is The problem? i mean can't if fly? Does The throttle Channel work? Or what wrong with de quad?

[@williamhelms9736]

How do I stop my quad copter with a hobbyking kk2.1 from flipping over?

[@danielpetterssons]

Have you tried to do a ACC Calibration?

[@shubhampant5172]

Helo, is auxilary pin is must to connect because only four channels are working in my remote

[@danielpetterssons]

+Shubham Pant The aux pin its just for flight mode! If u only have a 4ch remote tjena u do not need The aux/auxilary pin

[@s.kcreators7750]

please tell me how to set the kk2.51.5 and we well to want fly the my vresles moter please help me

[@Rampage00769]

Help! I cannot get mine to arm? Just started doing this, can't understand why? I have checked and rechecked everything. The receiver is getting signals as the KK2 is reading them in the receiver test menu so I am stumped?

[@madhavchoksi9329]

are u getting any change in reciever test??
I am getting idle only

[@Rampage00769]

+Madhav Choksi Receiver test shows everything as it should be, just will not arm, it was working fine the day before. Strange.

[@Rampage00769]

+Madhav Choksi The armed settings I can find is Auto armed and you can only switch it from yes to no,. Either way changed nothing.

[@madhavchoksi9329]

+Rampage I am getting zero in ale,rud,thr, etc and in general idle

[@marianohernandez198]

thanks

[@niharranjanmahali8549]

Hello sir, i built a quadcopter by kk2.1.5 but never flying it because i have facing a problem i.e when i connect battery to the quad and after esc calibration the motors are automatically runs without throttle and also witout arming.....so this is a big strange, what can i do plz help me

[@MegaMaheshvarma]

Hv u sorted out ur prblm bcz nw I'm facing it any suggestions frm u

[@niharranjanmahali8549]

Hii, i left the kk f.c and no longer using that because i didn't find any solution for that issue but most probably i guess that was because of the blheli firmware esc's which is not supported by kk. So if you using that kind of esc's then replace those to simonk firmware, may be this will work but i suggest better to go for other advanced flight controllers like F4, naza, pixhawk etc. those are really awesome open source boards.

[@creativeflu6619]

thanks..

[@GurifriskyGurifrisky]

Hi, I would like to know how to connect KK21EVO to a module miniosd mavlink osd apm 2.6. Thanks and regards

[@danielpetterssons]

Hi, I'm sorry but I am not in to that "micro controller" stuff. But I wish you goodluck with your search!

[@GurifriskyGurifrisky]

Ok. Thanks very much

[@turrboot6763]

hi
I have a problem in my quadcopter whem i turn on self level my quadcopter be so vibration
may you help me pleas

[@danielpetterssons]

Okey... Hum! have You checkt on your self level settings?

[@lilufabegum8939]

new kk 2.1.5 is preprogramed??

[@eldiablo155]

thank you ;)

[@madhavchoksi9329]

hello..... my quadcopter is not getting armed... please help me as soon as possible

[@danielpetterssons]

+Madhav Choksi have u change the armed settings?

[@Rampage00769]

+Madhav Choksi Did you get it solved, I am suddenly having the same problem.

[@madhavchoksi9329]

+Rampage no bro I think there would be some mistake in connections.... can u pls give me your email address

[@Rampage00769]

+Madhav Choksi Got it! When you go to arm it make sure the throttle trim is zeroed out on transmitter as well as the stick all the way down. then move stick to the right

[@madhavchoksi9329]

+Rampage ok let me try......moreover can please upload a video here on RUclips

[@surajitbanerjee5806]

Please help me ...my kk2 1.5 seen self - level is on but when i try to armed it not armed please help me...

[@Technovibes7889]

Ya same problem with me

[@guruji243]

Hi mine after armed only two motors run. Any help please? Thanks

[@AshokRaptor]

guruji243 do a esc calibration

[@BasilYohannantesla]

i m having an older ver or kk 2.1
i facing problem setup. should i upgrade the firmware

[@danielpetterssons]

+Basil Yohannan
yes, I don't really know! but u can try that! or just buy a new one!
but have you tried ot reset your kk?

[@nawfalbinmuhammed4532]

no

[@darpanbashyal1597]

is there no any need of buzzer in our kk2.1.5 fc.

[@danielpetterssons]

ýou dont need to have a buzzer but its good to have so you know when the battery is low.

[@darpanbashyal1597]

oh that's ok..then it in not a principle required components of our drone.. so tq fr that..?

[@smrizwan8164]

How to connect it to the transmitter

[@danielpetterssons]

On the left side of the board, you have 5 channels of control input,
1-Ail
2-Ele
3-Thr
4-Rud
5- AUX

[@smrizwan8164]

Thanks

[@akstyles404]

Bhai aap ye dron ka matirial kaha se late ho

[@akstyles404]

Bhai jara app ka name like ke Ripley karona

[@MrLeviaFUN]

I never had to press buttons 1 and 4 to calibrate the ESC....

[@danielpetterssons]

No. But for The throttle calibration.

[@danielpetterssons]

+Levkin or I do not know you might have a newer software...

[@sargaranisha5538]

my one motor has not respond

[@Unknown-nc4ce]

hi how to step the kk 2.15 plse tell me

[@danielpetterssons]

hey I do not quite understand what you mean with 'step' the board!?

[@beepbob3128]

My kk said "error no yaw input"

[@sumanbhatta9746]

how on safe level in mini kk2.1.5

[@danielpetterssons]

i dont really know. i dont have the mini KK board

[@Unknown-nc4ce]

sorry, how to setup kk 2.15

[@Desmessed]

please remove the props when configuring the board. I've seen some really nasty pictures of people skipping that step...

[@danielpetterssons]

Oh sorry. Tanks for telling me and yes is not funny when its happen ...

[@shubhampant5172]

Now the board is not working( kk 2.1.5 ) it display works when i turn on the battery, after 10 sec. Of plug on the battery the display got white and no switch works.

[@Unknown-nc4ce]

s ur right, now myn also that problem what we what to do plse some body help