Bro I ordered new kk 2.1.5 board from flyrobo but while programming the screen text went off I tried your method but its not working please tell me what to do. and it cost me 4887 rs
Thanks for the suggestions, but while i incenses the THR, only the fourth motor is rotation, others are only making a beep sound.. my question is, can u suggest some that, that with this process, i could easily achieve the success for rotating all the four motors, in order to process the quad-copter operations.
sir mere flight controller ke resiver setting me aileron no signal dikha rah hai aur yaw, rudder, etc signal dikha rah hai kya aap mujhe baata sakate hai kya problem
Hey man, I did your procedure, it worked. The blank screen error was solved and SAFE screen came. But once I connect the ESC back to the normal port, it shows version and keeps blinking, nothing else is working.
Found even easier method. Just connect the 4th esc normally. Connect the Green wire from flash pins (as in video ) to positive+ of Buzzer. That's it Done.
@@coolplus1830 Brother first of all thank you for seeing my problem...... Let me explain u.... I got the parts yesterday i tested my kk flight controller with a single esc just to know how it works and it worked flawlessly. But when i soldered all the esc's together on the frame and when I connected the signal pins on the kk and connected the battery then for some duration the buzzer was(still only the lcd backlight was lit up and not the display) working but after some time even the buzzers too stopped and there was no display yet only the backlight. So yesterday night i gave up and guessed to wait until tomorrow then today when i thought of working on it and connected the battery the buzzers, display worked!! But just for 2 secs aftet which it faded away...... Do note the following : 1. all things are soldered perfectly on the frame 2. I didn't tested all the esc one by one with the controller only i tried with one with which i thought other 3 will also work and i soldered them. 3.I haven't charged the battery since i got it because my charger broke. Please i request you to reply me as soon as possible because i have a presentation nearby and i gladly thank you for all your support.... Pls help!! Regards
@@adityapruthi01 bro in that case there are 2 things possible. Firstly charge your lipo and then try it out if it doesn't work reflash it with the latest firmware. For flashing you need a usbasp cable available for 250 ₹ online.
And thank God.... I just got lucky it worked... Actually my charger was faluty and it wasn't charging my lipo which the new one did and now its working like a charm...... But bro pls help me with another thing...... 1) I've calibrated all things, used the correct apparatus but when i move the throttle above 50% it (with the propellers on Nd just testing, tied it up to the base) all apparatus just reboots and it stops...... Else if i don't have the proppelors on only the motors then if i give it 100% throttle too it doesn't stalls... 2)Even when sometimes it handels 100% throttle it does not lifts off......it even does not leave the ground even.... 3)well today I found out that my lipo voltage alarm was showing the votage of my cell 1 and 3 and not 2nd......is that possible???. And is it the reson that to maybe why my quad is not getting full voltage from my battery and it stops after half throttle Nd i can't get my quad to fly????..... Bro please reply ASAP coz to be honest i dont have really anyone to discuss this topic to and i want it to get ready before 9th of sept...... Pls help bro Thanks...... Pls keep in mind my apparatus 1000 kv motors 30 amp esc Kk 2.1.5 F450 frame 3300 mah 25c lipo 1045 proppelors
Then in that that case there is no problem with the board. Check if this thing happens with another transmitter. I think that there's some problem with the transmitter
thank you so much bro ❤️ working my drone
I tried using this method on the controller but it did not work after removing the wires. What could be the problem?
If even this does not work try reflashing using usbasp cable with latest firmware.
Bhai wo kaise hoga
Hello sir i have a dought will the kk215 board will work if i give power only
I mean no esc but giving 5 voltage power only
What if we change the controller? Will the new controller work? Or it’s a problem in something else...?
The problem is with the screen, change the screen instead
Clear as mud with all those wires and not knowing if the RX is needed or not and what setting ..
Bro I ordered new kk 2.1.5 board from flyrobo but while programming the screen text went off I tried your method but its not working please tell me what to do. and it cost me 4887 rs
Thanks for the suggestion. After connecting the wire but there is no display in screen.
i was tried but not working please give a saggesions .
my problem is that my kk screen in blank and the red light above it is not blinking properly help plz
Same here black screen
Love from kullu himachal pradesh
Thanks for the suggestions,
but while i incenses the THR, only the fourth motor is rotation, others are only making a beep sound..
my question is, can u suggest some that, that with this process, i could easily achieve the success for rotating all the four motors, in order to process the quad-copter operations.
Calibrate the ESCs
@@coolplus1830 after flashing I had done the acc calibration, but it didn't work..
Is acc calibration and esc calibration both are same??
esc callibration is differ
push the 1,4th button at a same time and plug in kk board and before on the remote of drone
Thanks solved my problem!
Not worked for me getting same blank screen. Any help ??
sir mere flight controller ke resiver setting me aileron no signal dikha rah hai aur yaw, rudder, etc signal dikha rah hai kya aap mujhe baata sakate hai kya problem
Thanks so much 🙏🙏
thank youuuuuu bhai bohot madad kar di tune
Its not working please help
Try reflashing
In my case after reflashing black display with light I said black not blank please help
Can I help you
@@johnmaxsun3577yes
Can u please help me @@johnmaxsun3577
Thanks. It works like a charm 👍🏽👍🏽👍🏽🤜🏼🤜🏼
Polycarp Laurent cool
did you have to leave the cables on ?
@@johnciccolella3421 yes bro
can we remove the wires after doing what you said
No you hve to leave them connected
The d2 led blinks along with the blank screen
Hey man, I did your procedure, it worked. The blank screen error was solved and SAFE screen came. But once I connect the ESC back to the normal port, it shows version and keeps blinking, nothing else is working.
Try reflashing
Can provide the details of the wires
After we flash should we connect the esc back to where we had connected it before flashing
Yes
Thanks 😊
I have try your ideas still not getting solution can you please assist me
bro I have connected those wires as u said . But still it is a blank screen.it is not displaying any words.plz give me a solution
You saved my life dude
Bro it's still like that.....what I want to do now
How to reflash???
I try to connect with 3.7 v and it show me blank screen is it battery low volt or it's kk2 problem
Connect it to a lipo , 3.7v is low voltage. If I remember right it needs 5v .
Thank u 🤩🤩🤩
thanks problem is solved
Why this problem occurs in kk2.1.5 ? Can u plz help
Brother if I do this also it is not working man any solution??
Why this problem happens ?
No solve white display plz help me
Still it's showing the same bro plz help
thank you mister
If we do reflashing its come perfectly yes or no plz reply
Most probably it will
@@coolplus1830 but from where I can buy the usbasb wire to flashings the kk2.1.5 controller
Robu. In
Thank you so much, it worked for me.
Thanks bro it's working
Hi bro...
At 1st time it's worked and again the display blanked like in ur video .. could u help me plz...
Try it again or try reflashing the kk board
And plz subscribe
@@coolplus1830 how to reflashing .... The way u showed in ur video is reflashing
@@saikumar-or6cb no this is not reflashing , wait I'll send you a link to reflash.
ruclips.net/video/tfiAzsHqtP8/видео.html , here's the link
hey bro it is still not working can you help me please
What should be done for solving this problem it is not use full please help me sir
BINDAAS LIFE SUDESH try reflashing with usbasp cable .
Cool plus how sir is there any video
Just search how to flash kk2
Ok sir thank you
It is not solved, plz help
@cool plus
Please reply brother
BHAI TUCH THO
Found even easier method. Just connect the 4th esc normally.
Connect the Green wire from flash pins (as in video ) to positive+ of Buzzer. That's it Done.
Thanks man, he's method didn't work but yours did!
SO YOU HAVE TO LEAVE THE WIRES ON ? WHERE CAN I GET THE WIRES , WITH THE CONNECTORS LIKE YOU HAVE ?
They come with the FC
I DIDNT GET with any of my control board , but you can get them on ebay I see.
do they have to be left on ?
@@johnciccolella3421 yes
@@johnciccolella3421 search for jumper wires on Amazon.
Can i contact u somewhere else, like any other social network please reply really need in immediate help
Bro pls tell me your problem here
@@coolplus1830 Brother first of all thank you for seeing my problem......
Let me explain u.... I got the parts yesterday i tested my kk flight controller with a single esc just to know how it works and it worked flawlessly.
But when i soldered all the esc's together on the frame and when I connected the signal pins on the kk and connected the battery then for some duration the buzzer was(still only the lcd backlight was lit up and not the display) working but after some time even the buzzers too stopped and there was no display yet only the backlight.
So yesterday night i gave up and guessed to wait until tomorrow then today when i thought of working on it and connected the battery the buzzers, display worked!! But just for 2 secs aftet which it faded away......
Do note the following :
1. all things are soldered perfectly on the frame
2. I didn't tested all the esc one by one with the controller only i tried with one with which i thought other 3 will also work and i soldered them.
3.I haven't charged the battery since i got it because my charger broke.
Please i request you to reply me as soon as possible because i have a presentation nearby and i gladly thank you for all your support.... Pls help!!
Regards
@@adityapruthi01 bro in that case there are 2 things possible. Firstly charge your lipo and then try it out if it doesn't work reflash it with the latest firmware. For flashing you need a usbasp cable available for 250 ₹ online.
@@coolplus1830 well a sincere thanks for your reply
And thank God.... I just got lucky it worked... Actually my charger was faluty and it wasn't charging my lipo which the new one did and now its working like a charm...... But bro pls help me with another thing......
1) I've calibrated all things, used the correct apparatus but when i move the throttle above 50% it (with the propellers on Nd just testing, tied it up to the base) all apparatus just reboots and it stops...... Else if i don't have the proppelors on only the motors then if i give it 100% throttle too it doesn't stalls...
2)Even when sometimes it handels 100% throttle it does not lifts off......it even does not leave the ground even....
3)well today I found out that my lipo voltage alarm was showing the votage of my cell 1 and 3 and not 2nd......is that possible???.
And is it the reson that to maybe why my quad is not getting full voltage from my battery and it stops after half throttle Nd i can't get my quad to fly????.....
Bro please reply ASAP coz to be honest i dont have really anyone to discuss this topic to and i want it to get ready before 9th of sept......
Pls help bro
Thanks...... Pls keep in mind my apparatus
1000 kv motors
30 amp esc
Kk 2.1.5
F450 frame
3300 mah 25c lipo
1045 proppelors
Doesn't work
i tried the same method bt it's still now working... what to do now??
typing mistake... It's still not working... help me plz...
Reflash
isaki motor ki vaering nahi samajh me aa raha hai
Nothing happen anything
Plz make a video how to flashing with usb cable
Making
link plz
Bro it doesn't work please help me
Brother this method is not working is there any other way???
You can try re flashing if possible, but it requires an additional cable
Can you explain how i do reflashing ??
@@pulseonthebeat ruclips.net/video/ilxuy2_ybTw/видео.html
brother can you give me the link of latest fireware?
Which I can do to refresh my kk2.1.5
I have followed your steps bro. But still it shows the same error
Can you suggest me to overcome the issue
Thanks for the ideaaaa
It doesnt work...
Is it necessary to do this whenever we want to run the drone or only once?
You have to keep it connected as it is, even when you fly.
Varalana unna othuduven da😂
Bro I have one doubt
Hea yo thanks it works
Bro board fry ho gyaa....
It is not working
Not working man plz help or give me a way to contact you.
Bro write your query here I'm active
Try reflashing the kk2. 1.5 board that may help
Ya planning on buying USBASP cable for that. But I don’t think that will work.
Do you sell flight controller. Maybe get a cheaper rate from you if you’re from INDIA
Bro I try this method but it's not working please reply
My also
It worked but hove to use it pls tell me
I hve already explained the whole process in another video, check out my channel 😁
no in my case it was not working
TECHNICAL BOY KAPIL I think that means that the board is gone.
But my board is new
It happens second time in my new board
not working
Try reflashing the board
when i power on my transmitter, my board screen automatically blank
Then in that that case there is no problem with the board. Check if this thing happens with another transmitter. I think that there's some problem with the transmitter
not working