Absolute legend, my switch has been bricked for a few weeks now, tried a few different methods but due to it being on the latest software it never worked, have now managed to get it working with this method 10/10 would recommend as a true legend
After mounting the system partition, what happens if you delete everything stored in the "save" folder and only copy the two generated files "120" and "80000000"? as well as with the registered folder. 8:49
Thank you very very much! I unbricked my Nintendo Switch after 3 years or so after updating my nand backup with this guide to the latest firmware and it looks like it works now!
Hello, could you tell me what method I could follow for an OLED switch that has a purple screen? When trying to restore the nand it reports "failed to init", it seems that it no longer communicates with the emunand? This console was used for a while in the dock, after which it presented this error and never returned.
you can do what I did in the video. but if the emmc is corrupted, you need to replace it and try to do the level 3 unbrick guide. if u have the backup nand, you can try to restore it
I have basically the same problem but i can restore the nand but then i get pkg2 read error. The backup is known to work, i made an emunand from it to test it. When i flash boot0,1 after the full gpp the partitions get wiped. Do you think my eMMC is dead and needs to be replaced or i can fix it with instinct and maybe reflow?
Hi @sthetixofficial , first thanks for this amazing video, I can solve my sysnand problem with this guide, but unfortunately I have a problem when I try to recovery the eMMC When I try to restore SD emuMMC BOOT0&BOOT1, the process faild and hekate don't give me the the second option to restore 😢, the option stay in grey and can't do anything more. I have SD partition created and emuMMC assigned. Can you give me a little of help, lots of thanks
when attempting to delete all contents from the registered folder an error pops up and it says disk is write-protected. i have turned off the "read only" only button from the console like in the video
so the save folder created using emmchaccgen aside from the one with the "120" suffix it also have a file name with "8" followed by several "0"s. Do I also copy that over or do I just have to strictly copy the one with the "120" suffix
I need help! when trying to mount the system stays on mounting... no window to install the driver i installed from the folder and still keeps the same. Any advise?
Do you have a specific guide for if my switch, following a hard freeze during a game on my emummc, now only boots to the Nintendo logo or to Atmosphere once I launch it using my Hekate injection as usual? I am given a black screen in both instances and not sure if your in brick guides cover this exact scenario. Thanks
@@sthetixofficial sure will take a look, so it's possible my nand got corrupted and that's why the switch won't turn on past Nintendo logo even without an SD card in?
Thanks I was able to troubleshoot the switch I bought that was stuck on the second logo, now it launches but the wifi does not work, from what I found on the internet a problem on this wifi chip can brick the console on older firmware but not on recent ones, if I understood this tutorial I updated the console firmware by directly modifying the console files? Thanks again !
Hi, I need some help. I got stuck with the 2b error and hence I started out with this guide. My sysNand boots fine and it was the emu that was causing the 2b atmosphere panic. What happened was as below: 1. The back up step did partial restore because of no space in the emuNand partition. I do not know if this is a problem but I am stating that for completeness. I moved out the bin files to pc and completed the backup. So now my backup folder has boo1 and boot1 and rawnand.bin.08 to rawnand.bin.14. 2. Completed all the other steps and at the restore step I got a file not found when I tried to restore boot0 and boot1. I moved these to the emummc folder instead of leaving it at the restore folder and that did the trick. But then restore ALL option was grayed out - I assume this is because of step 1 partial back up issue. Now when I launch cfw I got stuck with pkg1/pkg2 mismatch, old hekate error. Now I have no idea what to do. Do I go level 2 (even then wont step 1 still be an issue) and do all steps there for my emuNand partition. Should I do level 1 for sysNand to get its firmware up? If so how do I fix the emuNand not booting into cfw? Also ny sysNand is stuck at 12.0.1 version, so I am not sure if that is an issue. Also I did extract the latest HATS onto my SD card and I do have a nand back up on my PC from when I did the CFW for the very first time. Can you please help me out?
@@sthetixofficial Just one question - if partition size is 29 GB again I will have the same space issue for emuNand right, so how much should I allocate when I do the partitioning?
Yo bro can you help me my 3ds wont play games that i downloaded recently (before the new update) instead itll give me an arm11 error, i tried to fix it can you help me
I have Erista which does not boot (black screen 15V/0.4A) to sysmmc, but cfw/atmosphere works. I tried this guide with latest FW but still does not boot to sysmmc. Any other method than systemwipe? Thanks!
Hi @sthetixofficial , first thanks for this amazing video, I can solve my sysnand problem with this guide, but unfortunately I have a problem similar with eMMC, when I try to restore SD emuMMC BOOT0&BOOT1, the process faild and hekate don't give me the the second option to restore 😢. I have SD partition created and emuMMC assigned. Can you give me a little of help, thanks
Unfortunately its not the same for me. I want to fix emuMMC that is 10GB. And the eMMC ALL is not active. The function is in gray and cannot be pressed. For MMC the function is present, but not for SD emuMMC RAW partition ON.
I have a Switch Lite that, when turned on, shows a screen that says “unable to start software”. When I click “ok” it reboots back to the same error screen. Do you have a video on how to fix this? I can not access the Home Screen but I can access the maintenance screen. Thank you.
It did ….I accidentally booted into Sysmmc and used daybreak to downgrade 18.1.0 from 19.0 and stuck with black screen….I followed this guide and used 19.0 firmware on Hexmmc program….it worked But Wifi is not working in both Emummc and sysmmc
Hi, does this method risk getting my console banned? I’ve never hacked it before. Since I updated it, my Switch has been stuck on a black screen, even when I try to force a restart. I erased the data through safe mode, which still works, but the black screen persists. It’s a V1 model, probably unpatched since I bought it a few months after launch. Would simply following the steps in your video be enough to get me banned?
Hi! Is it possible to unbrick nsw v1 unpatched with 19.0.1 via this guide? Have trouble with loading ofw and cfw, not booting, only black screen, only can access to hekate. Burn fuses for 19.0.1 and don’t have backup for 18.0.
Thank you so much for your reply. I have a V1 unpatched switch and I'm able to run hekate and copied your HATS pack to the SD card. I'm still unable to launch the OFW or thr CFW from hekate. I hope you can help me.
@@sthetixofficial, I check my sd card trying to full format, and I notice the storage is 134Gb but it is a 128 sand disk. I guess the sd card was the culprit. Thank you sir
An excellent video as always !!! I would also like to ask if it is possible to unban a banned console by formatting and then use different keys while following the guide.
Thanks for the Guide! I can't install any NSP over 4GB after doing this, i believer cause my card is fat32, but the capacity is 128GB so i know i have the space, any thoughts?
I want to create Introductory video for new3ds cfw. I have created a backup file and will change to use a new sdcard. How do I restore it? Do I have to install GM9 or what do I do? Please use the restore method, not the file transfer method.
If I wanna play a legit game (bought new by myself) online but still wanna use some overclocking, will I be safe from a ban, if I play that game online on the SYSMMC (its clean there, no cheats and no pirated games at all) ?
@@sthetixofficial Thanks, I´ll look that up. You´re truly my Nr. 1 modder on RUclips. If I would ever be in Indonesia one day, I´m gonna visit your shop
I have. I did your latest unbrick method. And it showed me this after restoring the backup, "You're eMMC is initialized in slower mode! This might mean hardware issues!"
This could be affected by the modchip itself. What modchip do you use? it doesnt mean the emmc chip is damaged but the modchip could sent a fake signal about it.
I have a “pkg 2 decryption failed! Pkg1/Pkg2 mismatch or old hakate! Failed to launch Hos!” Error, I use the emummc part of the switch so I can play my games but I’m unsure which level should I start of how to fix it and I’m lost I appreciate it if there’s a fix for this, thank you.
@@sthetixofficial no but if I do use the level 2 should I use the new or the old level 2 method? I mainly want to get my switch fix so I can play the Emunand part of the switch because that’s what I use.
@sthetix what according to you would be a better investment in terms of modding and future proofing , a hackable V1 switch now or switch 2 in 2025 on launch day
I need try tomorrow , I have 2 switch OLED I make mistake I connect Dat0 to B , and now only hekate work but don’t boot nothing ( only black screen ) 😭
Bro Sthetix, my kid accidentalliy connected the switch to wifi and the console encountered keeps rebooting with an error code: 2123-0011 (0x167b). Will this method fix the error my console has? Thx
@@sthetixofficial ah nice banget, god bless you sekeluarga yah bang sthetix, aku akan coba sampe mentok buat CFWin sendiri, nanti kalo gk keberatan pas mentok aku tanya2 lagi ya 🫡
@sthetix i need help pls i cant propely make my prodkeys its says "(nofat)unable to mount a system " its the only step i cant make I NEED HELP SIR IM BEGIN
@@sthetixofficial i use emmchaccgen gui windows... The boot0 and boot1 is not same the size for Orginal boot1 boot0 that I have on my pc...is that normal
After doing this on ofw(sysnand), will i be able to play online without getting banned? I was randomly getting a pkg1/2 mismatch error or black screen depending what i click, so I restored the BOOT0/1 from a very old backup (when i was on sxos before switching to hekate/atmosphere). Now, if i start ofw without hekate or use the semi-ofw option, i get a black screen. If i start sysnand with cfw, i get the "Erista pkg1 on Mariko" error. If i start emunand with cfw, it works fine.
@@sthetixofficial Im having an issue trying to follow the guide. When i try to copy in the files (registered) into the mounted drive, it just doesn't want to copy over. i see it jumping between percentages (going up and down randomly, doesn't make sense). Also i noticed that in NxNandManager, the FW.ver says "NOT FOUND!". Not sure if this is an issue, im trying to use fw 18.1.0 (the one that does require a reboot). I also tried restarting my windows explorer and tried all 18.x.x versions of NxNandManager. Any ideas?
Hey so as far as I understand, hekate can only do a full restore. Not sure how I can use it to transfer the generated "registered" folder files. I tried restoring and doing the entire process again and the same thing happens. I can delete the existing registered files but once I copy new ones it just stays at 0%. Hoping you have a workaround or something
thanks for this information !!! and please I have 2 switch with nand scrashed and error tittle id 01xxx2B x=0 (0xffE) but your 4 tutorials no cant fix :( thanks for all saludos desde colombia !!!
This guy is FIRE!! old method/new method just awesome!!!
This black screen error was with me for whole year, I tried everything, but without result. This video finally helped me to fix this. Thanks a lot!
Glad it worked for you.
Absolute legend, my switch has been bricked for a few weeks now, tried a few different methods but due to it being on the latest software it never worked, have now managed to get it working with this method 10/10 would recommend as a true legend
Glad you have fixed the console.
Thank you so much. my Switch came back to life after this video
ขอขอบคุณ
Thank you for your support.
This video is so helpful. Just did my very first firmware rebuild and it was successful ! Thank you !
Great to hear!
Do you have a separate video for emummc? Thank you
same guide
I clicked on this video thinking I could use it to Unbreak my 3DS, and I watched it until you showed the picture of the Nintendo switch😂
After mounting the system partition, what happens if you delete everything stored in the "save" folder and only copy the two generated files "120" and "80000000"? as well as with the registered folder. 8:49
you can delete them all but you will lose the existing save data
@@sthetixofficial 👌
Tenho muita gratidão a você! Seu vídeo é sensacional e resolveu o meu problema. Deus o abençoe grandemente, meu amigo.
You are welcome.
awesome guide as always sthetix
at 5:41 if you are altering emummc where should BOOT0 and BOOT1 be placed? ( >restore>emummc or in >restore)
inside the restore, then emummc
At always "BIG BOSS" thanks for the tuto, let go fot Level 2 :D
i can't delete the registered files it tells me the disk is write protected
u did not disable the read only option inside hekate
7:45 disable read only in nxnandmanager default setting is enable
When transferring files to "Registered", the progress bar just freezes at 5%. What could the issue be
try to redo the copy process.
Will this work for a console getting a black screen after the atmosphere logo when booting to EMUMMC?
I get an error at 7:35 Nxnandmanager says "Keyset needed" and "bad crypto!" any ideas on this error please?
Because you did not do ruclips.net/video/npHEa68QKOA/видео.htmlsi=TRis80whEWcMsnh1&t=439
@@sthetixofficial Yer I did do that but still does not work. I have another Switch that it fixes but not this one, might have to try unbrick level 2
Thank you very very much! I unbricked my Nintendo Switch after 3 years or so after updating my nand backup with this guide to the latest firmware and it looks like it works now!
Great Video. THX.
This saved my switch, thank you so much!
Glad I could help!
muito bom!! voce é o melhor... thanks for all
Однозначно лайк, шикарный гайд, все понятно, реанимировал своб консоль
This ABSOLUTELY saved my switch from a terrible fate
Hello, could you tell me what method I could follow for an OLED switch that has a purple screen? When trying to restore the nand it reports "failed to init", it seems that it no longer communicates with the emunand? This console was used for a while in the dock, after which it presented this error and never returned.
you can do what I did in the video. but if the emmc is corrupted, you need to replace it and try to do the level 3 unbrick guide. if u have the backup nand, you can try to restore it
@@sthetixofficial In this case I will have to buy a new emmc to change the board, am I right?
if you used a Picofly chip, please discard it and use either the instinct-nx or hwfly. Pico could damage the emmc and it is a known issue.
@@sthetixofficial Thanks for the tip, I didn't know that, this time he was with a hwfly.
I have basically the same problem but i can restore the nand but then i get pkg2 read error. The backup is known to work, i made an emunand from it to test it. When i flash boot0,1 after the full gpp the partitions get wiped.
Do you think my eMMC is dead and needs to be replaced or i can fix it with instinct and maybe reflow?
Hi @sthetixofficial , first thanks for this amazing video, I can solve my sysnand problem with this guide, but unfortunately I have a problem when I try to recovery the eMMC
When I try to restore SD emuMMC BOOT0&BOOT1, the process faild and hekate don't give me the the second option to restore 😢, the option stay in grey and can't do anything more.
I have SD partition created and emuMMC assigned.
Can you give me a little of help, lots of thanks
maybe you did not put the boot0 boot1 inside the correct folder. It should be inside backup/alphanumericfolder/emummc/restore/
For the step Restore eMMC, for emummc it only supports partition-based. Any alternative steps for file-based emummc?
no we cannot do that.
when attempting to delete all contents from the registered folder an error pops up and it says disk is write-protected. i have turned off the "read only" only button from the console like in the video
nevermind found the read only in the nandxmanager program checked and just unchecked it
so the save folder created using emmchaccgen aside from the one with the "120" suffix it also have a file name with "8" followed by several "0"s. Do I also copy that over or do I just have to strictly copy the one with the "120" suffix
you can copy that too.
I need help! when trying to mount the system stays on mounting... no window to install the driver i installed from the folder and still keeps the same. Any advise?
i did the level 2 and everything was fine! thank you I was driving crazy!
Do you have a specific guide for if my switch, following a hard freeze during a game on my emummc, now only boots to the Nintendo logo or to Atmosphere once I launch it using my Hekate injection as usual? I am given a black screen in both instances and not sure if your in brick guides cover this exact scenario. Thanks
you can try following the guide but it could be an issue with the modchip as well.
@@sthetixofficial I use an original switch model so no need for a modchip
Try repairing it with the level1 unbrick guide.
@@sthetixofficial sure will take a look, so it's possible my nand got corrupted and that's why the switch won't turn on past Nintendo logo even without an SD card in?
ya probably.
Thanks I was able to troubleshoot the switch I bought that was stuck on the second logo, now it launches but the wifi does not work, from what I found on the internet a problem on this wifi chip can brick the console on older firmware but not on recent ones, if I understood this tutorial I updated the console firmware by directly modifying the console files? Thanks again !
you are welcome
Getting an error not letting me delete registered files because it is write protected and its not a physical thing because my micro sd doesn't have it
Hi, I need some help. I got stuck with the 2b error and hence I started out with this guide. My sysNand boots fine and it was the emu that was causing the 2b atmosphere panic.
What happened was as below:
1. The back up step did partial restore because of no space in the emuNand partition. I do not know if this is a problem but I am stating that for completeness. I moved out the bin files to pc and completed the backup. So now my backup folder has boo1 and boot1 and rawnand.bin.08 to rawnand.bin.14.
2. Completed all the other steps and at the restore step I got a file not found when I tried to restore boot0 and boot1. I moved these to the emummc folder instead of leaving it at the restore folder and that did the trick. But then restore ALL option was grayed out - I assume this is because of step 1 partial back up issue.
Now when I launch cfw I got stuck with pkg1/pkg2 mismatch, old hekate error.
Now I have no idea what to do. Do I go level 2 (even then wont step 1 still be an issue) and do all steps there for my emuNand partition. Should I do level 1 for sysNand to get its firmware up? If so how do I fix the emuNand not booting into cfw?
Also ny sysNand is stuck at 12.0.1 version, so I am not sure if that is an issue. Also I did extract the latest HATS onto my SD card and I do have a nand back up on my PC from when I did the CFW for the very first time.
Can you please help me out?
just make a new emummc from scratch. it is way easier
@@sthetixofficial Just one question - if partition size is 29 GB again I will have the same space issue for emuNand right, so how much should I allocate when I do the partitioning?
it depends on the SD card quality. make sure you use SD partition
Yo bro can you help me my 3ds wont play games that i downloaded recently (before the new update) instead itll give me an arm11 error, i tried to fix it can you help me
Same here 😢
try using the latest luma3ds boot.firm
I tried it it didn't work what should I do? :/
you did not do it properly OR it is caused by a bad game. try to rename the Nintendo 3DS folder to any name and try to boot your console again.
you need to delete the game via godmode9, it could be that your game is damaged.
I have Erista which does not boot (black screen 15V/0.4A) to sysmmc, but cfw/atmosphere works. I tried this guide with latest FW but still does not boot to sysmmc. Any other method than systemwipe? Thanks!
you can dump your emummc and flash it to the sysmmc.
@@sthetixofficial Thank you! I need to create the emuMMC first. Do you have a video about dumping the emuMMC to sysNAND?
you said the cfw works, emummc worked?
eMMC all greyed out when I try to restore the partitions to emummc
you dont have the emummc probably? or your emummc is SD files type
Hi @sthetixofficial , first thanks for this amazing video, I can solve my sysnand problem with this guide, but unfortunately I have a problem similar with eMMC, when I try to restore SD emuMMC BOOT0&BOOT1, the process faild and hekate don't give me the the second option to restore 😢.
I have SD partition created and emuMMC assigned.
Can you give me a little of help, thanks
Unfortunately its not the same for me. I want to fix emuMMC that is 10GB. And the eMMC ALL is not active. The function is in gray and cannot be pressed. For MMC the function is present, but not for SD emuMMC RAW partition ON.
the emummc should be in the raw partition. try using the older level1 guide
I have a Switch Lite that, when turned on, shows a screen that says “unable to start software”. When I click “ok” it reboots back to the same error screen. Do you have a video on how to fix this? I can not access the Home Screen but I can access the maintenance screen. Thank you.
is the ofw working?
Those nxnandmanager work with 19.0.0? Thanks
It did ….I accidentally booted into Sysmmc and used daybreak to downgrade 18.1.0 from 19.0 and stuck with black screen….I followed this guide and used 19.0 firmware on Hexmmc program….it worked
But Wifi is not working in both Emummc and sysmmc
It should, just ignore the "unknown firmware" text
@@sthetixofficial thank you very much
Hi, does this method risk getting my console banned? I’ve never hacked it before. Since I updated it, my Switch has been stuck on a black screen, even when I try to force a restart. I erased the data through safe mode, which still works, but the black screen persists. It’s a V1 model, probably unpatched since I bought it a few months after launch. Would simply following the steps in your video be enough to get me banned?
My console was on version 10 (I think) and I upgraded to 19 a week ago and I'm stuck on it now…
you better get to hekate, disable the AutoRCM, test to launch the OFW
@@sthetixofficial Do you think it's possible despite the fact that I've never launched a single payload on my switch?
Update: auto rcm was already disabled :(
Worked Thank you very much
you are welcome.
Can we use NxNand manager to edit savefile files on sysmmc(stock) by mounting user partition?
u can
Hi! Is it possible to unbrick nsw v1 unpatched with 19.0.1 via this guide? Have trouble with loading ofw and cfw, not booting, only black screen, only can access to hekate. Burn fuses for 19.0.1 and don’t have backup for 18.0.
Yes you can.
Can I try this if my Switch is getting stuck at the Nintendo logo after turning it on and then turns off? My Switch does not have custom firmware.
you need to have cfw to follow this guide
Thank you so much for your reply. I have a V1 unpatched switch and I'm able to run hekate and copied your HATS pack to the SD card. I'm still unable to launch the OFW or thr CFW from hekate. I hope you can help me.
Thank you brother
when I try to emu raw gpp it says "error mounting" what does it mean>?
it means the data is not valid, or the nand is not valid.
@@sthetixofficial, I check my sd card trying to full format, and I notice the storage is 134Gb but it is a 128 sand disk. I guess the sd card was the culprit. Thank you sir
An excellent video as always !!! I would also like to ask if it is possible to unban a banned console by formatting and then use different keys while following the guide.
not possible.. once banned and your console is banned forever
Is this method suitable to fix for pkg1/pkg2 mismatch, pkg2 decryption error?
It depends on how you bricked it.
Thanks for the Guide! I can't install any NSP over 4GB after doing this, i believer cause my card is fat32, but the capacity is 128GB so i know i have the space, any thoughts?
just use dbi to install games via a usb cable
I want to create Introductory video for new3ds cfw. I have created a backup file and will change to use a new sdcard. How do I restore it? Do I have to install GM9 or what do I do? Please use the restore method, not the file transfer method.
just copy paste everything
I have a Nintendo Switch v2 or 2020, do I need to install picofly for this?
do not use pico. use instinct-nx
Awesome, can you do an 18.0.1 upgrade video please, you are awesome
you always can. same guide
If I wanna play a legit game (bought new by myself) online but still wanna use some overclocking, will I be safe from a ban, if I play that game online on the SYSMMC (its clean there, no cheats and no pirated games at all) ?
I think overclocking is safe but please find the info on the reddit community
@@sthetixofficial are there some communities on Discord or Telegram as well ?
@MrCANER06 on reddit or gbatemp, you can google it.
@@sthetixofficial Thanks, I´ll look that up. You´re truly my Nr. 1 modder on RUclips. If I would ever be in Indonesia one day, I´m gonna visit your shop
My OFW/SYSMMC won't boot. Stuck on Nintendo logo. Need help. I tried the all your past unbrick tutorial from your channel
do you have the original prodinfo?
I have. I did your latest unbrick method. And it showed me this after restoring the backup, "You're eMMC is initialized in slower mode! This might mean hardware issues!"
This could be affected by the modchip itself. What modchip do you use? it doesnt mean the emmc chip is damaged but the modchip could sent a fake signal about it.
@@sthetixofficial I have the same problem. picofly rp2040.
I have a “pkg 2 decryption failed! Pkg1/Pkg2 mismatch or old hakate! Failed to launch Hos!” Error, I use the emummc part of the switch so I can play my games but I’m unsure which level should I start of how to fix it and I’m lost I appreciate it if there’s a fix for this, thank you.
try to extract my pack, www.sthetix.info/hats-releases
I’ve downloaded them and installed them still the same error is there level unbrick method that works?
the level2 is what u need. do you have a working backup nand?
@@sthetixofficial no but if I do use the level 2 should I use the new or the old level 2 method? I mainly want to get my switch fix so I can play the Emunand part of the switch because that’s what I use.
@SonicKidXD is your sysmmc working?
@sthetix what according to you would be a better investment in terms of modding and future proofing , a hackable V1 switch now or switch 2 in 2025 on launch day
buy a hackable switch now, don't buy a v1, buy an oled. don't think about the switch 2, it won't get hacked soon
with hacked swith I would get an awesome library of timeless games, you will be covered until switch would be hacked
I need try tomorrow , I have 2 switch OLED I make mistake I connect Dat0 to B , and now only hekate work but don’t boot nothing ( only black screen ) 😭
Bravo
Bro Sthetix, my kid accidentalliy connected the switch to wifi and the console encountered keeps rebooting with an error code: 2123-0011 (0x167b). Will this method fix the error my console has? Thx
Just to let ya know that I just have it fixed by updating the default.txt. Thx bro
You are welcome.
i got the error ' bad crypto ' on both device id and fw ver !
please redo the guide.
im getting this error message imput file/drive is not a valid nx stogare
They maybe your nand is 100% corrupted?
bro pls 2002-4687 error can work again?😢 it has been 3 years now
I dont know what that is
Bang nanya bang..
Kalo tulisannya begini gimana cara fix nya...?
"emummc is forced but not enabled failed to launch hos"
Karena emummcnya gak ada bro.
bang, kalo mau nge-CFW Switch V1 Softmod (series tembus) terbaru nih guidenya liat di mana ya?
ruclips.net/video/_v-bGPtUXOk/видео.html
itu dan pake pack saya t.me/HATSPACK
@@sthetixofficial ah nice banget, god bless you sekeluarga yah bang sthetix, aku akan coba sampe mentok buat CFWin sendiri, nanti kalo gk keberatan pas mentok aku tanya2 lagi ya 🫡
This works if you can access RCM only. My console has a soft brick and has a black screen with Nintendo logo.
Awesome!! Hope I never need it 😅
i have a question. once you unbrick your switch, do you still have the capability to play online or did you get console ban? (because im not sure)
you can, as long as your console is not banned previously and have the original prodinfo.
@sthetix
i need help pls i cant propely make my prodkeys its says "(nofat)unable to mount a system " its the only step i cant make I NEED HELP SIR IM BEGIN
Please use lockpick_rcm to dump the console keys.
Error hekate restore Not fonde boot1 boot0 and 4 bkgl file sub and mine why!!!!
Save file i fonde 2 file 120 and 8000000b copy all 2 file or one!??
yes just restore both of the files.
and maybe you did not open / use the emmchaccgen properly.
@@sthetixofficial i use emmchaccgen gui windows... The boot0 and boot1 is not same the size for Orginal boot1 boot0 that I have on my pc...is that normal
Of course that is normal. I even posted the issue in the video and you need to ignore the size.
Cool! 🎉
thanks MAS :)
After doing this on ofw(sysnand), will i be able to play online without getting banned? I was randomly getting a pkg1/2 mismatch error or black screen depending what i click, so I restored the BOOT0/1 from a very old backup (when i was on sxos before switching to hekate/atmosphere). Now, if i start ofw without hekate or use the semi-ofw option, i get a black screen. If i start sysnand with cfw, i get the "Erista pkg1 on Mariko" error. If i start emunand with cfw, it works fine.
You selected the wrong console type.
your console is Mariko, but you chose Erista.
You can re-unbrick the sysmmc using the guide, and choose Mariko
@@sthetixofficial Im having an issue trying to follow the guide. When i try to copy in the files (registered) into the mounted drive, it just doesn't want to copy over. i see it jumping between percentages (going up and down randomly, doesn't make sense). Also i noticed that in NxNandManager, the FW.ver says "NOT FOUND!". Not sure if this is an issue, im trying to use fw 18.1.0 (the one that does require a reboot). I also tried restarting my windows explorer and tried all 18.x.x versions of NxNandManager. Any ideas?
Is there another alternative to nxnandmanager i can use maybe? or some other way to get the generated files into the switch?
You can use Hekate to restore the files to your console. the FW not found is not an issue.
Hey so as far as I understand, hekate can only do a full restore. Not sure how I can use it to transfer the generated "registered" folder files. I tried restoring and doing the entire process again and the same thing happens. I can delete the existing registered files but once I copy new ones it just stays at 0%. Hoping you have a workaround or something
thanks for this information !!! and please I have 2 switch with nand scrashed and error tittle id 01xxx2B x=0 (0xffE) but your 4 tutorials no cant fix :( thanks for all saludos desde colombia !!!
do the systemwipe and test it
bro your the best
worked
after i pressing emu raw gpp is says error mounting sd card , any help?