Replacing JAMMED front ABS sensor on Honda Accord 2003 to 2012

Due to factors beyond the control of RB The Mechanic, it cannot guarantee against unauthorized modifications of this information. RB The Mechanic assumes no liability for property damages or injury incurred as a result of any of the information contained in this video. RB The Mechanic recommends to follow safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, chemicals, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of RB The Mechanic, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not RB The Mechanic.
RB The Mechanic. All rights reserved. Publication, reproduction or distribution of this or any video by any means whatsoever, including without limitation electronic transmission via internet or e-mail, or re-uploading existing videos & re-uploading such material on any website anywhere in the world, is strictly prohibited without the prior written consent of RB The Mechanic.
#abssensor #hondaabssemsor #2003accordabssensor #hondaaccordabsensor #abssensor #antilockbrakesensor #antilock #frontabssensor #hondafrontabssensor #accordfrontabssensor #2004accordfrontabdsnesor #2005accordfrontabssensor #2006accordfrontabdsensor #2007accordfrontabssensor #2009accordfrontabssensor #2008accordfrontabssensor #2010accordfrontabssensor #2011accordfrontabdsensor #2012accordabssensor #jammedabssensor #jamedhondaabssensor

[@alphadog1961]

When you live in Canada,everything is siezed.Mine came out in pieces and then it had to be cleaned out with a drill bit.This video is the reality I live in...THANKS.

[@RBTheMechanic]

Yeah this is nothing compaired to what happnes to car from Canada I seen those!!! Appreciate the good comment!!

[@robertdickerson16]

Just did this on a 2007,
Drilled it out in 7 minutes with 2 bits ,easy work if u know,u know

[@RBTheMechanic]

Yeah

[@OKBAOK]

Thanks good video. Thanks for saving us some money 👍🙂

[@RBTheMechanic]

No problem 👍

[@donniev8181]

​@@RBTheMechanichere
ruclips.net/user/shortsUsDDa7wgvwc?si=b7trfTT7BDr7OJx3

[@musicfashionstyle4251]

I already changed my all new wheel speed sensor. But abs, vsa light still not gone. Anything else for help.

[@RBTheMechanic]

What codes did u have?

[@goodguygto]

Hey Ralph Bob The Mechanic!, at 0:10 you were talking to the ABS sensor. I think you need to switch to decaf! No more of!☕️☕️☕️☕️☕️🍩🍩

[@RBTheMechanic]

Lol yeah

[@FunwithAhadandSarina]

Why you burn wires of sensor, you can pull downward the black thing with long plier?

[@RBTheMechanic]

Nope it’s jammed got to go

[@hanselldisla4643]

@RB the mechanic , hello sir how you doing very good job getting out that nightmare sensor .I have a question I have a 2010 Acura MDX and the codes I’m getting is for the battery and the rear right wheel sensor I did check the battery and is good the voltage is above 12.9 on cold crank and when I did the load test it did not went down for more than 10.5 voltage with the car on is 14 voltage. But the thing is that the lights come on sometime like for 2 days and then it went off for about 3 weeks.it not permanent it’s a intermittent issue. When I got it on it show ABS,VSA,SH-AWD and trailer stability assist. I see in your scanner it was showing battery too and the speed sensor after you changed the wheel speed sensor the issue gone ?

[@RBTheMechanic]

It could be low voltage causing the issue or the sensor as well

[@hanselldisla4643]

Thank you for your response back. The issue in your case was the speed wheel sensor ? After the fix no more lights on ? I ask you because I check my battery and the voltage was fine.

[@RBTheMechanic]

@@hanselldisla4643 ok

[@user-ok8yl8og8j]

Could fhat keep the air from going through the line

[@RBTheMechanic]

This has nothing to do with any air

[@user-ok8yl8og8j]

@@RBTheMechanic ok do you have a idea why it wont let the air flow

[@user-ok8yl8og8j]

I need to know because I get off work at my regular job at 5 pm Central time . And Im going to go see if it just needs someone that knows how to bleed the brake lines . Or if indeed there is a more serious problem