Use code ERICSDIY for 10% OFF on maxpeedingrods products Coilovers: www.maxpeedingrods.com/product/maxpeedingrods-24-way-adjustable-coilovers-for-nissan-350z-z33-03-08.html?tracking=ERICSDIY
I was super stuck thinking why is the spring so compressed with no load when I installed it with the strut on its longest setting. But after seeing you install I’m gonna disregard it and hope for the best
Does it make a difference leaving the coilovers intact for rear? mounting them sep? Seen alot do them together. Does that little coil spring GIGGLE IN THE bucket
Hey bro I have a 2005 g35 with a key stuck in the ignition, it starts up and runs and stuff but key won't turn all the way back to come out. Any idea why?
i think they sponsor him so he gets them for free but i think if your other suspension components are solid these are fine. just can’t expect the highest quality like you get from BC coilovers.
I bought these exact same ones for my z and am having trouble getting them set right. At full droop the shock is 17.5 inches long. I’m gonna have to extend it at least an inch more but that’s gonna put me past that 25mm of thread they recommended keeping. I’m at a point where I’m thinking the shock is too damn short. Did you have any issues like this?
Hi Eric. I'm Having A Problem With My 2007 Infiniti G35 Sport Sedan. I Bought it To Autozone To Read My Check Engine Light They Pulled Up Code P0335 Crank Shaft Position Sensor. Do You Have Any Suggestions And Wath Brand Do I Use If I But The Part. BECAUSE my Care Us Stalling?
Use code ERICSDIY for
10% OFF on maxpeedingrods products
Coilovers: www.maxpeedingrods.com/product/maxpeedingrods-24-way-adjustable-coilovers-for-nissan-350z-z33-03-08.html?tracking=ERICSDIY
Great vid. Always enjoy your content!
Had to sub you really detailed
I was super stuck thinking why is the spring so compressed with no load when I installed it with the strut on its longest setting. But after seeing you install I’m gonna disregard it and hope for the best
A great video and they might have a new costumer.
Does that nut you needed for the rear have to be a special grade nut or any kind is fine as long as it fits the bolt ?
At 12:00 , can you not reuse the oem rubber mount ?
No, the maxspeedingrods coil is much smaller in diameter, so the oem mount doesn't work on it.
@@ERICSDIYGARAGE ahh okay thanks for the insight . That sucks tbh
Does it make a difference leaving the coilovers intact for rear? mounting them sep? Seen alot do them together. Does that little coil spring GIGGLE IN THE bucket
It doesn't fit that way. And no the spring doesn't move around
Hey bro I have a 2005 g35 with a key stuck in the ignition, it starts up and runs and stuff but key won't turn all the way back to come out. Any idea why?
sounds like bad ignition switch
Are these the COT6?
Yes
Great video , how much is the labour cost for that job
I charge 400
Thank you
Question aren't tien better than maxspeed? Why downgrade?or are these just to review the?
i think they sponsor him so he gets them for free but i think if your other suspension components are solid these are fine. just can’t expect the highest quality like you get from BC coilovers.
It was a sponsored video. My rear tien shocks were blown, so it was a good time to swap out. I agree tho tien does ride better
BC coilovers are also not high end quality. you will have to look at other brands and price points to get that.@@rightclicksaveit
I bought these exact same ones for my z and am having trouble getting them set right. At full droop the shock is 17.5 inches long. I’m gonna have to extend it at least an inch more but that’s gonna put me past that 25mm of thread they recommended keeping. I’m at a point where I’m thinking the shock is too damn short. Did you have any issues like this?
They probably sent you the wrong shock reach out to them for a replacement longer shock
Do they come already preload adjusted?
Yes
Hi Eric. I'm Having A Problem With My 2007 Infiniti G35 Sport Sedan. I Bought it To Autozone To Read My Check Engine Light They Pulled Up Code P0335 Crank Shaft Position Sensor. Do You Have Any Suggestions And Wath Brand Do I Use If I But The Part. BECAUSE my Care Us Stalling?
Get the Hitachi brand
@@ERICSDIYGARAGEsolid ass advice!!
Maxpeeding rods😂😂😂😂
Where are they made from?
China 🇨🇳
@@brandonburnett9288 oops.
@@brandonburnett9288 OOPS...