Это видео недоступно.
Сожалеем об этом.
Heat pump tumble dryer finding faults and error codes Aeg, Electrolux, John lewis, Zanussi
HTML-код
- Опубликовано: 4 сен 2024
- Get your appliance fixed faster! Click the link below to browse our supplier's huge selection of appliance parts and support the channel at the same time! (repairpartstea...)
www.how-to-rep...
Check our website page above for error codes and service manual on this AEG Tumble dryer.
Don't forget to subscribe to our channel and click that like button if you enjoyed this video.
The videos on this channel and the content on the website really helped me to tackle investigation of my machine. I got an "E32 - Conductimetricsensing oscillation frequency too low" error code, which according to the Electrolux manual is an Electrical / Main Board fault. After finding no obvious wiring faults, I spent £160 on a new board but this didn't fix the fault. Whilst banging my head on the closed door in desperation I heard a microswitch clicking when I applied some pressure to the door. I investigated further and found that the little plastic tongue in the top of the door wasn't going far enough into the body of the machine to activate the switch. I found that extending the plastic tongue by about 2mm using a piece of tape fixed the problem!
hi i have error 31 and 32, have very long drying time, i dont know what can i do.
The David Attenborough of appliance repair
Thank you for the video. I knew my motor cap needed replacing (bump start test after the hum started) and this helped me get to the right place. To note, my dryer has a cap for the motor above the cap in the video, part of the white cable tray in front of the spring. Thought I'd help anyone else who has a similar dryer. :)
Glad it helped you with your tumble dryer glad we could help you @jontelling this is for you ruclips.net/user/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
you are good and clear in your explanations: good professional
Thanks How-2,
this video was extremely instrumental whilst repairing a AEG LAVATHERM 59800 I was asked to have a look @. 😀😀.
Really glad the video assisted you. We're always here to help. Have a great Christmas and a happy New Year. Thank you very much for subscribing to the channel
Our float / sensor (13.08 in the video) was clogged so that it constantly indicated that the machine had to be emptied.
Needs to be cleaned once a year.
Thanks for a helpful video!
How do you do this? What part of the machine is this please I’m having the same problem
Hi Paul, from your video I was able to figure out either the float switch or the pump was not working, removed the pump and applied 240v, it turned so had a look at the float switch, I removed it and it all looked good so think it may have stuck down stopping the pump coming on. Cleaned out the reservoir put it back together and filled it with water as the machine was drying, it pumped the water out as the level got near the top. Hope it stays fixed. I very much appreciated your advice.
Can you tell me how to get into test mode on Grundig GTN39250GCW? Many thanks
Dear Paul, thanks for the good explanation, great help, saved a lot of money
Very nicely produced video - thanks!
I'm glad that you found the video useful. Please remember to subscribe to the channel as that helps us. Hope you had a good New Year
glad we could help you @asbjorn.mejlvang this is for you ruclips.net/user/shortse432SAb2g08 please remember to subscribe as that's what keeps this channel going. Thanks 👍
Hi Paul, very informative video. Thanks a lot. It's very rare, but another test that can be done on the compressor is to measure resistance between each of the terminals, common, run, start, and the compressor chasis, to check for current leaking. Greetings from Spain.
Is there a video for changing the belt on this machine?
hi, i have very long drying time , all test done and have e31 and e32 errors, but everything i think working, what the problem can be?
Hello.Nice video.I have same model.Dryer working but after ~ 40min I get error code EHO. The fan near compresor not working,i did not chek the fan but I check voltage it is not come 220V from the board.
i have siemens heat pump dryer everything is working great but no heating what to test or replace please
Hi , does the compressor only work when the elektro motor is turns on ? My circuit breaker shuts off the moment when i start a program .
When i unplug the motor , the breaker stays on , when i plug in back the motor and unplug the compressor , the breaker also stays on . I ve tried the service mode till my fingers hurt butt it won’t work with me , please help , thank you
At 5:20 you mention the heating/cooling matrix and that you are not going to show it on this video since the drum needs to be removed. Do you by any chance have a video on this? It seems to me that the only thing that is going to remain is the bottom part. I need to clean it since it is fully clogged and condensation is pilling up in front right below the filter. Pump is good and so is sensor. If I pour water in the back and in service mode, pump activates and pumps the water in the tank. Any video with removal/cleaning of the matrix along with what it takes(dismantling) to get there will be greatly appreciated. Thank you.
I have error code E63 on C5, C6, and C7, and then error code E32 on C8, C9 and C10. I have replaced the heater element and thermostat but still have the same error codes. Can you suggest anything please
Thanks for your awesome videos, using these I was able to confirm the condenser pump is working fine, but water is pooling at the front of the machine. I have removed the filters and all seems clean, but water isn't passing front the front to the back to be pumped out. Any suggestions? Cheers, Mike.
Champion 😊
I have a Samsung dryer with a heat pump 9kg compressor, it takes 3 to 4 hours to dry if I put two towels after they come out of the washing machine, is this normal or is there a weakness in the dryer? The temperature of the internal drum is approximately 45 degrees Celsius, while the LG dryer reaches 90, how can I increase the drying efficiency and temperature by changing the capacitor?
intresting,very cool info....didn t know i was subbed,but i can see why,good channel!!!!
I got an aeg T96690IH. Does not turn on. Display is dead. I have measured 25v to the front panel board which goes to zero when you press the start button. Still no start. Any help is appreciated. Thanks
I did the work to clean the matrix on an AEG T96690IH. All good, but when I reassembled the dryer and tried to start it I get an E91 code. After a quick search, error is for a communication error between main board and display. There are only two connectors between the two boards and you cannot do it wrong. What I did see though is that the connector to the motor can go either way. This is the only thing I might have done wrong. Also the
light in the drum area stays on. Any clues? Thanks
please feel free to contact me in the website where you will actually be able to get in touch with me
i have a perfect care 900 electrolux heat pump dryer, i complain that heat to much and shrinkage the clothes, i called the service mo error codes founded but they changed the mother board, after that the fan was doing on and off every 2 minutes like it should be, but unfortunately only for the first cycle, in the second one the fan switched on only to 2 randomly and thn never more like before changing mother board, but now in the cooling phase last 10 minutes the fan work, but the way it still heating to much and shrink my clothes, what i can check on it?
what kind of lubricant is used between the belt ruler and the rod, please
I have this model and often it seems to stop before the clothes are properly dry. Does this indicate a problem with a sensor and, if so, how do I find out and clean/repair it? Thanks.
Renie Crossland Music i have the same problem? Keep stop (switch off ) it seems finish but it doesn’t dry. Can you help me? Please
With this test all working de pomp motor fan compressor but when i start the machine de fan compressor doe nothing and also i get not water in the reservoir under de pomp is dry i wait for your reaction thanks
this may be a sensor or it could be the start relay on the compressor you need to check if they have power
Having problem trying to get into test mode on the John Lewis heat pump dryer you are using
Have tried loads of times as u have shown with no joy
JimmyR
Great video really good breakdown. I've bought a recon heat pump dryer that's B rated, I was after an a++ one. Could I open it up and upgrade some components from a more efficient model to get to A++ or am I dreaming ?
I'm not a great fan of heat pump dryers in my opinion they are not cost-effective. Thanks please remember to subscribe as that's is was keeps this channel going. Thanks 👍
@@How-to-repair First of all thanks for finding time to share all this knowledge with us, i need your opinion on my AEG Lavatherm Exclusiv Protex, it over drying the clothes, what can be the problem? Thanks in Advance.
Thanks for your nice video(s)!. A question about my 65370AH3 (somewhat simpler, no display), does it have a TEST MODE too? Any hint for entering into that mode?
I used the method in the following video and it worked with your model. "Aeg lavaterm protex condenser dryer model number t65270ac putting into test mode and reading error" from tim 100 channel. ruclips.net/video/aysjDpZuK5c/видео.html
Hi Paul,
I need to replace the belt on this machine, how do you gain access to fitting the belt? Do you remove the front panel or the rear panel to fit new belt?
I would need to know the full model number to help
Thank you for leaving a comment, I would love you to leave your opinion on our poll about manufactures building in obsolescence to appliances. ruclips.net/user/postUgkxygHomnUySd_bYjaJBdEHPO6T4dYo9Ahm
and this is for you ruclips.net/user/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
@@How-to-repair the model number is an AEG T96699IH heat pump dryer, similar to the one in video Paul, any help would be appreciated 👍
hi i have the same machine and the same problem.the dryer works perfectly except 2 things.a)after drying i found only 1/3 of water to the collector on a full cloth drying and b)after drying i found returned water under the filters.Normaly this area it should be dry.i think the route from the front to the pump was closed.any idea to clean this route? thank you.(the pump works correctly).
I have the same problem, did you find a solution?
Do you still have the machine? I am about to take it apart in order to clean the condenser/evaporator unit. I am confident there is so much buildup there that no water can pass through and exit out the back for it to be pumped.
Just finished taking apart the machine and at the end the case where the condenser/evaporator are housed in the bottom. Not a fast job. A good 2 hours work to get there. Opened it up and cleaned it thoroughly. You cannot imagine the built up inside the fins and the "mud" on the bottom. All clean now. Waiting for it to dry up so I can put it back together. It will function as good as new, and dry clothes faster too. Lets see. For the record, it is impossible to clean the unit if you do not take it apart. If you ask me, there is a pretty bad design there. Lint will build up eventually and it will clog up. If there was a side door you would be able to do the job without tearing the entire machine down.
@@tamtakosxxx I am having the exact same problem. It is 6 years old , so I assume the build up of lint is the problem. Just wondering if it helped to clean it out?
There maybe an internal blockage between the front and back of the machine. On mine this was the case. I took the pump housing off to discover sludge which I sucked out with a silicone tube. To check if you pour water in the front at the small water filter area you should see the rear pump housing fill up.
hello can replace the compressor in the Hoover dryer ?
Hello , great videos, thank you alot for the know how. Is the front fan supposed to suck air or blow out ? Thank you in advance
Can you do us a favour and please share this video on your timeline Facebook twitter etc .
This will help other people who can’t get engineers out to help them.
ruclips.net/video/rFyGAHVFUW8/видео.html&t
facebook.com/how.to.repair.appliances/
Stay safe
I have the European version of AEG. Unfortunately, the pipe has copper + aluminum :(
can you show how clean buttom part ? how remove belt ?
I'm looking to buy a heat pump dryer in the U.S. ; which make and model would you recommend???
Hi I have AEG T856801H. It’s one of the early protex models. There is water flooding out the bottom of my dryer and no water in recovery tank. My filters are immaculate and so is front of condenser. Could it just be my pump needs cleaning. It was moved recently and unfortunately laid on its back would this cause a problem Please help
Excellent video thank you. What about error E73, any suggestion?
Iam Glad we could help you.
My Ebay Shop rover.ebay.com/rover/1/710-53481-19255-0/1?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fstr%2Fhowtorepair&campid=5338676951&toolid=20008
If you ever need help please use our site for 24 hour response www.how-to-repair.com/help/contact-us/
If have a question please use our site for 24 hour response www.how-to-repair.com/help/contact-us/
Please remember to subscribe to our channel
ruclips.net/user/Apart4u
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or
website on your timeline. This helps us a lot and if we really helped you can
always buy us a beer how-to-repair.com/help/buy-paul-a-beer/
Please remember to mark us to your favourites also I would be grateful if you would
subscribe to our channels social media as this really helps my site and keeps
us going.
RUclips. ruclips.net/user/Apart4u
Facebook. facebook.com/how.to.repair.appliances
But where is heating source on this one ? I still don't get where air becomes warm
Hi how can I fix the problem for same model is working 5-10min and stop ?
Hi I'm replacing the motor
And it's still don't work
Maybe is the capacity ?
If you can have a humming noise, then there's a good chance, it may be the capacitor @user-ts5ds7td1f please remember to subscribe to our channel as that really helps us ruclips.net/user/shortse432SAb2g08 Thanks, Paul 👍
Hi, we have a JLTDH21 that doesn't dry any more, it doesn't show any fault codes so I tried your trick of pressing the buttons to get it into test mode but it doesn't work? I have tried lots of time but I cannot get into test mode, any hints?
BTW its been cleaned thoroughly.
Very useful tutorials, thank you. Our John Lewis 7Kg heat pump tumble dryer is stopping before the indicated time and not drying the clothes fully. I have cleaned the bottom matrix which was pretty clogged. I put it in test mode and the individual functions appeared to work. At C9 it shows an E32 error code. I see what that is in your list of error codes, but do not know if that is something that may be fixed by me or would require a service engineer?
John Lewis heat pump tumble dryers are usually manufactured by the Electrolux group without the full model number. I am unable to point you in any direction, but if you contact us through the website I would be happy to try and assist you
hello
wat about to enter test mod in AEG LAVATHERM T56740
Have a fault on out electrolux dryer. I can hear the relays clicking but the tumbler isnt turning. E5e in the display. Also e32. What tests should I perform?
hearing the relays click does not necessarily mean it is working correctly. without having the machine in front of me I might be giving you false information. I'm sorry I'm unable to help with this one
please remember to subscribe to the Channel as that's what keeps us going and able to make videos for you
ruclips.net/video/7KmnizwuUEM/видео.html&t this might have helped
I have error code E63 on C5, C6, and C7, and then error code E32 on C8, C9 and C10. I have replaced the heater element and thermostat but still have the same error codes. Can you suggest anything please
hi paul can them heat pump dryers be regassed
yes but only with right equipment
Can you do us a favour and please share this video on your timeline Facebook twitter etc .
This will help other people who can’t get engineers out to help them.
ruclips.net/video/rFyGAHVFUW8/видео.html&t
facebook.com/how.to.repair.appliances/
Stay safe
Dryer stops and shows E71. I can clear the code and have another go and it stops again between 10 min and 60 min, showing E71. Is the NTC you have shown in the video the problem? Is it a 4.8k@25C? Do you carry the part?
E71 which is an NTC (temperature sensor) problem or pcb
Iam Glad we could help you
Please remember to subscribe to our channel
ruclips.net/user/Apart4u
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or
website on your timeline. This helps us a lot and if we really helped you can
always buy us a beer how-to-repair.com/help/buy-paul-a-beer/
Please remember to mark us to your favourites also I would be grateful if you would
subscribe to our channels social media as this really helps my site and keeps
us going.
RUclips. ruclips.net/user/Apart4u
Facebook. facebook.com/how.to.repair.appliances
Hi electrolux dryer showing error R32 what is the reson
Hello I have the AEG and the error code is EH0! ! ! HELP! ! ! ! THANKS
Where’s the best uk element as I have E60 error code
Hola alguien me puede ayudar mi lavadora AEG me sale EHO en la pantalla como solucionarlo ya q en mi pais no hay servicio tecnico de esa marca
my tumble dryer doesnt show anything on displey
You didn't cover the heat pump or thermal switches? I'm trying to diagnose a Bosch dryer that has lost heat. Can't work out which component provides the heat
The compressor itself. The first radiator is the condenser and second one the evaporator. This one gets hot and warm the air, about 45-50 degrees
I miss some information on how to change the drive-belt.
Anyone here who have experience on how to change the trumble-belt?
I have an Electrolux model EDH3478RDW.
you need to take off drum
We have an AEG LAVATHERM 86590IH3 dryer. (Type TC12H6BHP). After normal operation we found lots of water under the dryer, on the floor!!!! When I opened the filter door, there were lots of water in that area. I have started investigating the pump area at the back of the machine. I have determined with a digital multimeter that the resistance of the pump was about 750 ohm. In one of the videos the repairman mentioned that according to the service manual it should be about 750 ohm. So at this moment I assume that the pump is OK....... Next I will try to check the float sensor/switch which turns on/off the pump. Am I on the right path? Has anyone ever experienced this problem before? (I have not put the machine into diagnostics mode, yet).
I have similar problem. Pump is working and so is micro switch. In test mode i can empty the reservoir where the pump is pumping water from. But the water flow between the water filter in front and the reservoir in the back seems to be blocked so water flows too slow for the pump to be able to work effectively. I think the passages needs to be rinsed but am currently unsure how to proceed.
Andrew Szekely I’ve got same issue
To Andrew Szekely and Jens Klüwer-Ulrich
I have the same problem. Did you find the solution for this problem?
I have the same problem, water isn't going from the heat pump area at the front to the pump area at the back. Pump system works fine, but there seems to be a blockage between the front and the pump assembly. Did you have any luck with finding a solution.
@@jenskluwer-ulrich5875 I have the same problem. Water build up at the front of the machine, and not going to the back where the pump is. The pump works fine if I pour water into that area, but water doesn't get there. Not sure how to fix this problem.
My electrolux dryer died board after 5 years. Rust all around, realy poor quality.
Спасибо. Filter+ ixbt.photo/?id=album:63795 Capron/porolon/viskoze
Kishor
When I run the pump it doesn't completely empty the reservoir at the back. When the water gets to a bout 1cm depth the pump doesn't seem capable of pumping it up. Is this normal or do I need a new pump?