Hi, I'm Steve, nonda's lead mechanic engineer. Feel free to leave your comments here if you have any mechanic questions, I will be glad to help you out!
i’m about to purchase a used 2010 chevy malibu an it has a P00016 code an i’m wondering if the sensors aren’t replaced what would happen ? could it just be a faulty sensor or an actual problem
@@mariahford9356 You could potential he destroy the motor, the Chevy Malibu sensors aren’t that expensive. I would definitely change them out, so you can ferret out any other potential issues
I have a Toyota Camry with the code P0016 wondering if I need a new camshaft position sensor or a Timing chain and Tensioner I’m so confused wonder if I should replace one of each or in better off replacing both
@@Sean-vf7qr start with the sensor... toyota timing chains are pretty stout, generally- I doubt both the tensioner AND the chain are failing, but you didn’t say what year Camry, and the mileage it has.
@@CtRacerX my camry is a 2007 and has 200K miles still running good, I needed to replace the whole timing chain kit all of the parts that were replaced were all original
Waaat my man is a genius. Thanks buddy Definitely just started getting this code and my 04 blazer is Idling really low like to point its shaking but when I accelerate its fine. Once i come to a stop it starts seizing hardcore
ANY AND ALL HELP IS NEEDED AND APPRECIATED I had this code show 2003 GMC Astro later that day it died on me good thing at a gas station thought I was out of gas put $40 in the tank it started up it drove around the pumps to pull out and she died again. It was raining that day. All she wants to do now is crank but not turn over. Also I live in my van and haven't completed the whole insulation or get my vent fan installed yet so there has been a lot of condonsation.
Recently changed the solinoids intake and exhaust on my 2012 terrain GMC. Now check engine light is on and the stabilitrak says it needs serviced. Some times it turns off and lately it only let me go25 mph up steep roads and 46-47 on steady up hill roads. Only when on flat ground I could do the speed limit of 65 no problem.
I finished installing a timing chain tensioner and as soon as I finished k went for a test drive and now the check engine light shot on for P0016. I think I messed up the crankshaft timing because I remember having to crank the harmonic balancer to remove the tensioner
Hi Kevin, please recheck the timing belt/chain for proper alignment. Check the camshaft and crankshaft sensor wiring, and ensure that you are using the correct viscosity oil recommended on your vehicle's spec as oil level and pressure contribute to P0016.
Hi I have a 2017 Peugeot 3008 diesel . I have multiple fault code P1446, P15B£ , P2202 , P242F , P1113 , P2291 , P003D , P0016 . and the care doesn't start are all this code related to the same problem and when I lifted the bone I two little piece of the timing belt components.
Hi a skoda octavia 1.8 tsi shows the same error code after clearing the error code after 5-6 starts the error will appear hard to start and the performance will be lower. Camshaft Transmitter Valve Control Valve Replaced The control magnet has now been replaced if it does not solve the problem where else? Chain control was replaced 25,000 km ago.
I am getting this code in my 14 Malibu. Was told either solonoids or timing chain that would cost 1000 to replace. Vague codes. Now I have to plan for 1000 just in case
Hi Giovanni, it depends. You should know first what exactly is triggering the error, so you would know which part to replace and have an idea to the overall estimated cost. We recommend a manual inspection if there are damage to wiring, connections to the oil control valve, crankshaft or the camshaft sensors.
Hey Nonda, my car off and i put the diagnostic tool on it and I got the P0016 code Wednesday so last night I put a new crankshaft sensor on my 2013 VW Jetta TDI and that wasn't the issue. Won't start any suggestions?
I have a 2017 Chrysler Pacifica touring minivan with a 3.6 liter v-6 and am getting this code with the blinking check engine light of death. My shop wanted to put in a used motor at the cost of just over 6k. 😮 I’m hoping I can do these things and one of them will work.
Have a 2012 Audi A3. Slow crank starts... drives well. It’s been happening for a while. I thought it was the cold and battery being older (2017). Replaced the battery and same issue. Not sure if it correlates with the last oil change.. but the filter I bought wasn’t the same and I reused the filter (longer life). Service light came on a few days ago.. with p0016. First step was change battery. 2nd step considering oils change and filter (even though early) Would like to pursue steps in this video.. considered a new starter... been told it could be timing chain being stretched. I’m trying to avoid that job... seems hassle (not confident) or pricey. Thoughts? Vehicle has 75,000 miles
Hatchback and gas. My skill level is I understand stuff.. do my own oil changes, changed rotors, calipers and pads with buddy; transfer case with buddy, alternator, switched axles on a trailer.. just did glow plugs by self on 2008 f350.. kept old harness. At first it didn’t register the glow plugs, but decided to revisit the job and ensured the plugs were tight, and harness connected.. and works well. Trying to avoid mechanics as I feel to be taken advantage of, plus I enjoy learning and doing the work. Just don’t appreciate wasting time and sometimes the results aren’t what I want.. I realize that’s the learning curve.
@@nondainc That was the only one that I was told, and said they would have to do the timing chain. Except, the same person that said that wanted to replace the turbos a couple years back because oil was leaking... it was leaking by the plug on the oil drain pan. Seems like the it was threaded. So I changed the oil and ensured the plug was sealed... my wife was about to take the vehicle to them and spend $3k. Lost my trust at that point. :D I'll see whether my scan tool recognizes it this weekend, and whether other codes come up. Thanks for the responsiveness.
@@nondainc Only one code, but was there three time 1/3. Current, pending, permanent. P0016 Generic Senor A Crankshaft Position Camshaft Position Correlation Bank 1
Hi Trevor, we agree that there could possibly an issue with the timing chain. However, the crankshaft/camshaft sensors must be tested too to confirm if they are functioning correctly as this can also contribute to the appearance of the code.
I have a 07 Hyundai Tucson. Just got a tune up(Sept 22) and oil change (in Nov 22), and now I just got the P00016 error code on the scanner. Checked my engine oil, which was kind of dark but not low... I noticed my power steering fluid was low so I tapped it up. Now the check engine light came off. Scared to drive. I'm at work.
I have the code on my Benz s550 09. I will try these 4 steps and then go to the devil dealer. Does a Benz s550 09 have all steps 2-4? And would it be called the same or something else?
Hi, i have a 2010 Yaris 1.33 VVV ti. I changed the oil and the code went away for a while but now it's back. Sometimes it goes away then comes back. Do you know Which step i should do?
Hello, have you reset the check engine light and perform a road test to see if the code will still persist? Please also do a visual inspection on the wiring or connections to the components for possible issues.
@@nondainc Thank you very much for the reply. I tried resetting the check engine light, but I think I did it wrong with my vagcom, so I'll try again in a few days. I haven't taken it for a drive since the repair because I wasn't sure if it needed to be reprogrammed before driving around. The wiring and cables tested good when I replaced the sensors. Some of the clips are damaged from the previous owner, but it doesn't seem to be causing anything to fall out so far.
Hi there I recently replaced both vvt valves on my 2012 Toyota Camry and I still get the codes p0012 and p0016 I can’t seem to understand I tried everything in the video.
I get the code now after I had a new water pump and timing belt put on my 2008 Chrysler Sebring. My car also started jerking when above 70mph. When I took it back to the shop they said it wasn't something they did because if a timing belt was put on wrong it wouldn't work at all, and that I should go to a transmission shop to see what they think.
Hello, we suggest checking the wiring harness first for any damage (leading to and from the crankshaft/camshaft sensors), then proceed to testing the voltage of the sensors to see if they're functioning properly.
2013 Chevy sonic, heading the symptoms of bad mass flow air sensor (black smoke, sluggish, loss of power) just had oil change and changed MAF car seemed good for a few days but now back to the same or running. Giving 2 codes P0101 and P0016. I’m not a mechanic, just a car owner. Any help would be appreciated 😊
Toyota auris 2009 petrol 1.4 engine p0016 code, crankshaft position- camshaft position correlation bank 1 sensor a, this code came on my mechanic computer. Any thoughts please thanks in advance
Hi Whitney, to determine what's causing the issue, a wiring harness inspection to and from the crank/cam sensors is recommended (for visible damage). Make sure that the timing gear is aligned, and a tone wheel/pulse ring inspection is also recommended.
Hello, there are several factors that trigger this code and yes--you're right. Jumped timing is one. We'd also recommend performing the vehicle manufacturer's test for this code to avoid misdiagnosis.
I’m getting code P0016 on my 2011 Toyota Camry LE with 211,000 miles. Check engine light came on and I checked it and said that code. I’m not sure what or how to do things like this Besides oil change. My car drives rough but I think my tires need balanced
Hello, you may clean the Camshaft Oil Control Valve. If the issue will continue to persist, a replacement would be needed. Also, inspect the Camshaft Position Sensor and the Crankshaft Position Sensor (replace if necessary).
Hi Marlaya, since you are receiving multiple error codes, we suggest to get your vehicle visually inspected by your local mechanic for further diagnosis.
First, thank you for making this video. I already checked the variable timing control valves, from both banks. They both read 7.9 Ohms. Is it safe to assume that is not the problem? Cleaning them and putting them back on. Hopefully you'll read my message.
Hi Eder, it depends on your vehicle's make and model. You may check the manual. Kindly inspect the engine oil and filter as it can trigger this code also, if it's dirty then it should be replaced. Oil must be on the proper level.
I have a Mazda 5 2010 and after scanning it, it shows P0016 "Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A" but I don't know if its lack of timing or a Camshaft sensor problem
@weehauljunkremovalandhauli766 Still haven't. I can't afford paying someone to do it at the moment because of all the things I had to keep fixing to keep it moving, I'll probably try replacing the camshaft sensor to see if it works, if it doesn't solve the issue then I'll use it like that until I get a bit more stable economically.
@joepearlzz8504 yep, changed the Camshaft and Crankshaft position sensor and still have the same code. Although the engine doesn't do anything weird, but, the code is still there, so I decided to ignore it.
@@ChrisAzure did you erase the code after changing the sensors? If not try erasing it and see if it comes back. But from what I get from research, this codes are usually from vvt solenoid or chain issues… very weird if you never got any issues with this code
I have this code P001600 on a passat b6 2.0 tdi. Cbab engine code. The car doesn’t usally start when I had the car running and and is warm and I stop the engine When I try to turn it on i get the pigtail error flashing…
Hi I have 2018 Honda Civic type r and got the p0016 code while driving...the engine runs smoothly and plenty of power...when I clear the code it stays off while driving normally but when I start it after the engine is hot it comes back on...p.s sometimes it cranks awhile before it starts??? Any ideas would be appreciated thanx.
Need your opinion I've done everything Change the oil with correct viscosity Changed the vvt solenoid Checked the camshaft position sensor Checked the crankshaft position sensor But still the code exists p0016
Hi Rex, was the wiring harnesses inspected for damage? Also, was the timing chain/belt checked? Please know that even slightest misalignment can trigger this code.
P0016... Crankshaft position - Crankshaft position Bank 1sensor A ? ? My car lincoln navigator 2009 I have check engine lump and sound in side engine some time...
P0016 error code seems impossible to resolve.... is there any1 in the world 🌎 that has fixed this code.... because really... The people who made/build this cars can't fix it... I have a golf 7 gti 2013 model (South Africa)
Hello, if the suggestions provided in the video has been applied and the issue still persist, we recommend having the vehicle inspected by a mechanic for further diagnosis.
@@nondainc 2015 chev malibu, 2.5. I was watching someone testing the camshaft position sensor, and with the sensor out of the vehicle but connected, he put the multimeter pins in from the back and he was getting a reading of over 5 volts and when he touched the sensor with a wrench, it read zero. Mine on the other hand, shows very low, about .60 and when i touch it with the wrench, instead, goes to the 4.65. Weird. I just can't figure out what it is. I wonder if it's the timing chain. Thanks for the help.
Hello, in order to identify what's triggering the issue, we suggest to inspect all the related parts that would possibly contribute to the existence of the code. Kindly inspect all the wiring harnesses for damage, test the voltage of the sensors to see if they're functioning well. check the timing chain, and the crank/cam tone.
If the crankshaft sensor was faulty, wouldn’t you be getting more codes related to timing from the other sensors? I’m currently only getting one code, P0017. Is it safe to assume that the crank sensor is operable?
Hello, please know that there are other factors that trigger this code (P0017), and you'll need to do some diagnostic work to figure out the proper resolution to this trouble code. We suggest to have your vehicle checked by your mechanic to pinpoint the main issue and apply an accurate solution.
hi steve, ive change very sensor mentioned in this vid and also change the pigtails for both camshaft oil control valves. but, im still grtting codes p0016 and p0018. i have a 2004 toyota avalon xls 3.0 162mil. please help!!!
Hi Samuel, since you're getting more than one error code, we suggest getting your vehicle visually checked by your local mechanic for further diagnosis.
![How to Fix P0017 Engine Code in 6 Minutes [4 DIY Methods / Only $6.81]](http://i.ytimg.com/vi/Vcj-f_J2hyo/mqdefault.jpg)
Hi, I'm Steve, nonda's lead mechanic engineer.
Feel free to leave your comments here if you have any mechanic questions, I will be glad to help you out!
i’m about to purchase a used 2010 chevy malibu an it has a P00016 code an i’m wondering if the sensors aren’t replaced what would happen ? could it just be a faulty sensor or an actual problem
@@mariahford9356 You could potential he destroy the motor, the Chevy Malibu sensors aren’t that expensive. I would definitely change them out, so you can ferret out any other potential issues
I have a Toyota Camry with the code P0016 wondering if I need a new camshaft position sensor or a Timing chain and Tensioner I’m so confused wonder if I should replace one of each or in better off replacing both
@@Sean-vf7qr start with the sensor... toyota timing chains are pretty stout, generally- I doubt both the tensioner AND the chain are failing, but you didn’t say what year Camry, and the mileage it has.
@@CtRacerX my camry is a 2007 and has 200K miles still running good, I needed to replace the whole timing chain kit all of the parts that were replaced were all original
Thank you for having this video. Because you guys I was able to save money on my car after I get the zus. Big thanks 😊
Hello! We really appreciate your feedback!
Waaat my man is a genius. Thanks buddy
Definitely just started getting this code and my 04 blazer is Idling really low like to point its shaking but when I accelerate its fine. Once i come to a stop it starts seizing hardcore
We appreciate your feedback! If this is the only code you're getting, we suggest following the provided tips/solutions in our video. Hope it helps!
What fixed it for you? Same issue here. Hope to hear soon
ANY AND ALL HELP IS NEEDED AND APPRECIATED
I had this code show 2003 GMC Astro later that day it died on me good thing at a gas station thought I was out of gas put $40 in the tank it started up it drove around the pumps to pull out and she died again. It was raining that day. All she wants to do now is crank but not turn over. Also I live in my van and haven't completed the whole insulation or get my vent fan installed yet so there has been a lot of condonsation.
Recently changed the solinoids intake and exhaust on my 2012 terrain GMC. Now check engine light is on and the stabilitrak says it needs serviced. Some times it turns off and lately it only let me go25 mph up steep roads and 46-47 on steady up hill roads. Only when on flat ground I could do the speed limit of 65 no problem.
Please confirm if this is the only code you're getting.
I finished installing a timing chain tensioner and as soon as I finished k went for a test drive and now the check engine light shot on for P0016. I think I messed up the crankshaft timing because I remember having to crank the harmonic balancer to remove the tensioner
Hi Kevin, please recheck the timing belt/chain for proper alignment. Check the camshaft and crankshaft sensor wiring, and ensure that you are using the correct viscosity oil recommended on your vehicle's spec as oil level and pressure contribute to P0016.
Very precise presentation!
We appreciate your feedback, Melvin!
Hi I have a 2017 Peugeot 3008 diesel .
I have multiple fault code P1446, P15B£ , P2202 , P242F , P1113 , P2291 , P003D , P0016 . and the care doesn't start are all this code related to the same problem and when I lifted the bone I two little piece of the timing belt components.
Hi Orsi, since you are receiving multiple codes, we suggest getting your vehicle visually inspected by your local mechanic for further diagnosis.
Hi a skoda octavia 1.8 tsi shows the same error code after clearing the error code after 5-6 starts the error will appear hard to start and the performance will be lower. Camshaft Transmitter Valve Control Valve Replaced The control magnet has now been replaced if it does not solve the problem where else?
Chain control was replaced 25,000 km ago.
Hi Korándi, a loose timing chain could also trigger this code. Kindly have a check and fix to see if the issue will still persist.
I am getting this code in my 14 Malibu. Was told either solonoids or timing chain that would cost 1000 to replace. Vague codes. Now I have to plan for 1000 just in case
Hi I'm having this same error code for my 2010 jeep compass how much would something like that cost at a shop?
Hi Giovanni, it depends. You should know first what exactly is triggering the error, so you would know which part to replace and have an idea to the overall estimated cost. We recommend a manual inspection if there are damage to wiring, connections to the oil control valve, crankshaft or the camshaft sensors.
Hey Nonda, my car off and i put the diagnostic tool on it and I got the P0016 code Wednesday so last night I put a new crankshaft sensor on my 2013 VW Jetta TDI and that wasn't the issue. Won't start any suggestions?
Hello, please inspect the wiring harness (to and from the crank/cam sensors) for damage and check the timing belt/chain for any issues.
I have a 2017 Chrysler Pacifica touring minivan with a 3.6 liter v-6 and am getting this code with the blinking check engine light of death. My shop wanted to put in a used motor at the cost of just over 6k. 😮 I’m hoping I can do these things and one of them will work.
Did anything work?
Have a 2012 Audi A3.
Slow crank starts... drives well. It’s been happening for a while. I thought it was the cold and battery being older (2017). Replaced the battery and same issue. Not sure if it correlates with the last oil change.. but the filter I bought wasn’t the same and I reused the filter (longer life).
Service light came on a few days ago.. with p0016. First step was change battery.
2nd step considering oils change and filter (even though early)
Would like to pursue steps in this video.. considered a new starter... been told it could be timing chain being stretched. I’m trying to avoid that job... seems hassle (not confident) or pricey.
Thoughts?
Vehicle has 75,000 miles
Hatchback and gas.
My skill level is I understand stuff.. do my own oil changes, changed rotors, calipers and pads with buddy; transfer case with buddy, alternator, switched axles on a trailer.. just did glow plugs by self on 2008 f350.. kept old harness. At first it didn’t register the glow plugs, but decided to revisit the job and ensured the plugs were tight, and harness connected.. and works well. Trying to avoid mechanics as I feel to be taken advantage of, plus I enjoy learning and doing the work. Just don’t appreciate wasting time and sometimes the results aren’t what I want.. I realize that’s the learning curve.
Hi Trevor, have you double checked if there's any other trouble code registers together with this code?
@@nondainc That was the only one that I was told, and said they would have to do the timing chain.
Except, the same person that said that wanted to replace the turbos a couple years back because oil was leaking... it was leaking by the plug on the oil drain pan. Seems like the it was threaded. So I changed the oil and ensured the plug was sealed... my wife was about to take the vehicle to them and spend $3k. Lost my trust at that point. :D
I'll see whether my scan tool recognizes it this weekend, and whether other codes come up. Thanks for the responsiveness.
@@nondainc Only one code, but was there three time 1/3.
Current, pending, permanent.
P0016
Generic Senor A
Crankshaft Position
Camshaft Position
Correlation Bank 1
Hi Trevor, we agree that there could possibly an issue with the timing chain. However, the crankshaft/camshaft sensors must be tested too to confirm if they are functioning correctly as this can also contribute to the appearance of the code.
I have a 07 Hyundai Tucson. Just got a tune up(Sept 22) and oil change (in Nov 22), and now I just got the P00016 error code on the scanner. Checked my engine oil, which was kind of dark but not low... I noticed my power steering fluid was low so I tapped it up. Now the check engine light came off. Scared to drive. I'm at work.
Hello, can you please confirm if this is the only code you're receiving?
How do you know which sensor is the right camshaft position sensor to replace, intake or exhaust? I presume intake but wasted to ask.
Hi Pat, it's for the intake. Let us know if you have any further questions. Thank you!
I have the code on my Benz s550 09. I will try these 4 steps and then go to the devil dealer. Does a Benz s550 09 have all steps 2-4? And would it be called the same or something else?
Yes. Kindly follow the tips/suggestions provided in the video and let us know if the issue will still persist. Hope it helps!
Hi, i have a 2010 Yaris 1.33 VVV ti. I changed the oil and the code went away for a while but now it's back. Sometimes it goes away then comes back. Do you know Which step i should do?
Hi, if you own an OBD II device, please run a scan and try to clear the code.
Does the camshaft sensor need to be reprogrammed after replacement? Audi Q7, 4.2l V8
Hello, have you reset the check engine light and perform a road test to see if the code will still persist? Please also do a visual inspection on the wiring or connections to the components for possible issues.
@@nondainc Thank you very much for the reply. I tried resetting the check engine light, but I think I did it wrong with my vagcom, so I'll try again in a few days. I haven't taken it for a drive since the repair because I wasn't sure if it needed to be reprogrammed before driving around. The wiring and cables tested good when I replaced the sensors. Some of the clips are damaged from the previous owner, but it doesn't seem to be causing anything to fall out so far.
Hi there I recently replaced both vvt valves on my 2012 Toyota Camry and I still get the codes p0012 and p0016 I can’t seem to understand I tried everything in the video.
HI Lisset, we suggest getting your vehicle visually inspected by your local mechanic for further diagnosis.
I get the code now after I had a new water pump and timing belt put on my 2008 Chrysler Sebring. My car also started jerking when above 70mph. When I took it back to the shop they said it wasn't something they did because if a timing belt was put on wrong it wouldn't work at all, and that I should go to a transmission shop to see what they think.
Hello, we suggest checking the wiring harness first for any damage (leading to and from the crankshaft/camshaft sensors), then proceed to testing the voltage of the sensors to see if they're functioning properly.
If they put it off by a tooth it would indeed show up this code
2013 Chevy sonic, heading the symptoms of bad mass flow air sensor (black smoke, sluggish, loss of power) just had oil change and changed MAF car seemed good for a few days but now back to the same or running. Giving 2 codes P0101 and P0016. I’m not a mechanic, just a car owner. Any help would be appreciated 😊
Hi Darci, we highly suggest to get your vehicle visually checked by your local mechanic for further diagnosis.
I have the exact same engine and problem right now did you figure out what it was?
I have a 2016 Chevy sonic and this car has been nothing but a headache
Toyota auris 2009 petrol 1.4 engine p0016 code, crankshaft position- camshaft position correlation bank 1 sensor a, this code came on my mechanic computer. Any thoughts please thanks in advance
Did you find the problem?
Perfect thank you.
2012 Chevy Malibu 4.0
P0016, 17
P0442
Not sure where to start.
I’m having the same issue
I don’t know if just servicing the car is gonna work
Hello, you can follow the DIY tips/suggestions provided in our video on how to fix P0016. Hope it helps!
I just put a crank and cam sensor on now my car is ready p0016 it's a 06 chrysler pacifica. What do I do
Hi Whitney, to determine what's causing the issue, a wiring harness inspection to and from the crank/cam sensors is recommended (for visible damage). Make sure that the timing gear is aligned, and a tone wheel/pulse ring inspection is also recommended.
Does it turn on this error P0016 if the timing isn't good too
Hello, there are several factors that trigger this code and yes--you're right. Jumped timing is one. We'd also recommend performing the vehicle manufacturer's test for this code to avoid misdiagnosis.
Hi I have the following code on a guilietta : p0016 bank1 sensor b. What can I be?
Hi Reinder, have you checked your spark plugs?
I’m getting code P0016 on my 2011 Toyota Camry LE with 211,000 miles. Check engine light came on and I checked it and said that code. I’m not sure what or how to do things like this Besides oil change. My car drives rough but I think my tires need balanced
Hello, you may clean the Camshaft Oil Control Valve. If the issue will continue to persist, a replacement would be needed. Also, inspect the Camshaft Position Sensor and the Crankshaft Position Sensor (replace if necessary).
Hello, my car does not start at all. I had this code, can it be it is just the sensor?
Hi Adnane, please provide us with your vehicle's year, make and model.
I’m receiving a P2715, P0016, & P0700 on my GMC Acadia any suggestions? Thanks
Hi Marlaya, since you are receiving multiple error codes, we suggest to get your vehicle visually inspected by your local mechanic for further diagnosis.
Get a new car!
First, thank you for making this video.
I already checked the variable timing control valves, from both banks. They both read 7.9 Ohms. Is it safe to assume that is not the problem? Cleaning them and putting them back on.
Hopefully you'll read my message.
Hi Eder, it depends on your vehicle's make and model. You may check the manual. Kindly inspect the engine oil and filter as it can trigger this code also, if it's dirty then it should be replaced. Oil must be on the proper level.
I have a Mazda 5 2010 and after scanning it, it shows P0016 "Crankshaft Position - Camshaft
Position Correlation Bank 1 Sensor A" but I don't know if its lack of timing or a Camshaft sensor problem
Did you fix it ?
I got the same in CX 9. 2015 😢
@weehauljunkremovalandhauli766 Still haven't. I can't afford paying someone to do it at the moment because of all the things I had to keep fixing to keep it moving, I'll probably try replacing the camshaft sensor to see if it works, if it doesn't solve the issue then I'll use it like that until I get a bit more stable economically.
@@ChrisAzurehow about now? Did you ever get to changing the sensor and with any results?
@joepearlzz8504 yep, changed the Camshaft and Crankshaft position sensor and still have the same code. Although the engine doesn't do anything weird, but, the code is still there, so I decided to ignore it.
@@ChrisAzure did you erase the code after changing the sensors? If not try erasing it and see if it comes back. But from what I get from research, this codes are usually from vvt solenoid or chain issues… very weird if you never got any issues with this code
Good job
Thank you for your feedback!
I have this code P001600 on a passat b6 2.0 tdi. Cbab engine code. The car doesn’t usally start when I had the car running and and is warm and I stop the engine When I try to turn it on i get the pigtail error flashing…
Please provide us with your vehicle's year, make and model.
Problem behoben?
Was war das Problem?
Good good good good job.....👩🔧👩🔧👩🔧
Thank you!
Hi I have 2018 Honda Civic type r and got the p0016 code while driving...the engine runs smoothly and plenty of power...when I clear the code it stays off while driving normally but when I start it after the engine is hot it comes back on...p.s sometimes it cranks awhile before it starts??? Any ideas would be appreciated thanx.
Hi Neil, can you please confirm if this is the only code you're getting?
@@nondainc yes it is
Hi Neil, you may possibly have a timing belt issue. Kindly have it checked to confirm if a replacement is needed.
I think my car uses a chain..I was hoping it could be a bad sensor tho😊 but I have it checked out ill let u know what it was thank u
The car only has 38 000km on it to
Need your opinion I've done everything
Change the oil with correct viscosity
Changed the vvt solenoid
Checked the camshaft position sensor
Checked the crankshaft position sensor
But still the code exists p0016
Hi Rex, can you please provide us with your vehicle's year/make/model?
Fiat linea with 1.4 fire engine (naturally aspirated)
Yess I have change everything too and code still on
Hi Rex, was the wiring harnesses inspected for damage? Also, was the timing chain/belt checked? Please know that even slightest misalignment can trigger this code.
Hi Quintella, can you please provide us with your vehicle's year/make/model?
Good worker
Thank you for your feedback!
P0016...
Crankshaft position - Crankshaft position Bank 1sensor A ? ?
My car lincoln navigator 2009
I have check engine lump and sound in side engine some time...
Hi Abu, you possibly have a bad reluctor/ jumped timing chain or wiring issue. Kindly have them checked and fixed.
@@nondainc thanks
You're most welcome, Abu.
P0016 error code seems impossible to resolve.... is there any1 in the world 🌎 that has fixed this code.... because really... The people who made/build this cars can't fix it... I have a golf 7 gti 2013 model (South Africa)
I did all of them and im still getting this code on my chevy cruze
Hello, if the suggestions provided in the video has been applied and the issue still persist, we recommend having the vehicle inspected by a mechanic for further diagnosis.
In my case it was to repair the engine gears, only then the code was erased
✌🏻
I have code 0016 and did all these and the code is still there.
Hello, can you please provide us with your vehicle's make and model?
@@nondainc 2015 chev malibu, 2.5. I was watching someone testing the camshaft position sensor, and with the sensor out of the vehicle but connected, he put the multimeter pins in from the back and he was getting a reading of over 5 volts and when he touched the sensor with a wrench, it read zero. Mine on the other hand, shows very low, about .60 and when i touch it with the wrench, instead, goes to the 4.65. Weird. I just can't figure out what it is. I wonder if it's the timing chain. Thanks for the help.
Hello, in order to identify what's triggering the issue, we suggest to inspect all the related parts that would possibly contribute to the existence of the code. Kindly inspect all the wiring harnesses for damage, test the voltage of the sensors to see if they're functioning well. check the timing chain, and the crank/cam tone.
@@cartroublewannafix8611in other words yes unfortunately it’s the timing chain.
If the crankshaft sensor was faulty, wouldn’t you be getting more codes related to timing from the other sensors?
I’m currently only getting one code, P0017. Is it safe to assume that the crank sensor is operable?
Hello, please know that there are other factors that trigger this code (P0017), and you'll need to do some diagnostic work to figure out the proper resolution to this trouble code. We suggest to have your vehicle checked by your mechanic to pinpoint the main issue and apply an accurate solution.
Did you find the problem?
hi steve, ive change very sensor mentioned in this vid and also change the pigtails for both camshaft oil control valves. but, im still grtting codes p0016 and p0018.
i have a 2004 toyota avalon xls 3.0 162mil. please help!!!
Hi Samuel, since you're getting more than one error code, we suggest getting your vehicle visually checked by your local mechanic for further diagnosis.
Did you find the problem? And was it still running good with the codes?