How to install Mixet cartridge MXT07
HTML-код
- Опубликовано: 15 фев 2016
- How to install a Mixet cartridge MXT07. Make sure you have the correct cartridge the other cartage that is very similar to this one is for a faucet not a shower valve. I have many customers call me with the wrong cartridge installed and couldn’t figure out why it was so hard to turn. The faucet cartridge is Item 58386, for the shower MAKE sure you get cartridge MXT07. Life will be much easier for you
How to install Mixet cartridge MXT07
Follow as I guide you Step-by-Step in the removal and install of you new Mixet cartridge replacement. Grab an adjustable wrench, pliers or vise grips, Phillips screw driver, some plumbers grease and tub and shower caulking.
Turn off main water supply
Turn on a couple faucets to relieve any water pressure
Disassemble
Remove old cartridge
Clean,grease and insert new cartridge
Test for leaks
Caulk and place gusset, set and wipe excess caulking
Reassemble,
Done
Thank You for viewing Check out my amazon store and help support this channel. Click on the link below:
www.amazon.com/shop/theshack
Thank You for viewing
Subscribe, Share and Like
Follow me on twitter
/ backintheshack
Check out my home page
plus.google.com/u/0/
Check out My Channel
/ theshackhome 
Хобби
![PADDINGTON IN PERU - Official Trailer [4K] - Paddington Bear is back!](http://i.ytimg.com/vi/lKgitu25ZAg/mqdefault.jpg)
Thanks!
DS WOW Thank you You are the first to ever give from this video. Bless you thank you. It is my pleasure to help.
I looked at videos alllll day on how to repair a spinning handle, a shower faucet that does not get hot (but the sink does). I went to ACE and Lowe's to purchase a shower stem. Out of ALL the videos I watched, it was THIS VIDEO that showed me step by step what to do, but most helpful is that it had my EXACT shower pieces. That helped alot! I didn't know about the little tab thing in the faucet handle. Once I finally realized my shower handle had one (yes, I was one of the ones who just yanked off, but had I come across this video earlier in the day, I would have known about it). anyway I unscrewed it to reattach the handle (before I knew about it, I could NOT get the faucet to work). My guess is that whomever fixed it prior to me, also didn't know about that little tab. At any rate, thanks so much. My shower is now getting hot water, the handle works! and I've returned the pieces to both ACE and Lowe's and I'm going to cancel the plumber I had scheduled for tomorrow!!!
KarenJ0202 Superb. Glad it all worked out and you were able to cancel the plumber and save that money. Sounds like you can treat yourself to a nice dinner out....Thanks for viewing so happy to help.
Thank you soooooo much for this video. A year ago, I went to Home depot, and the sales guy matched up the valve, but apparently the wrong valve. I got it in ok, but turning the valve on and turning the mixture valve was a choir. This morning I watched your video, went to Home Depot with the P/N you indicated, MXT07, and followed your instructions, and now it works like a charm. Good Video....
You are very welcome. If I can help just one person it is worth it. Happy to hear you were successful
My water keeps driping why 😱😱😱😱😱
I live in a 115 year old building with a lot of hard water... They guy who sold me the valve recommended rolling up a washcloth soaked in vinegar, sticking it inside the pipe and letting it set for an hour or so... I did that, cleaned it out real nice!
Thank you Shack. Your video helped me immensely. Every morning, taking a shower was a really horrible experience. It would start off the day with a dark mood, hating my shower. I finally decided to change out the cartridge, and watched at least 6 other videos besides this one. Yours was the one that really helped me out. Now, every time I step in the shower, I feel a sense of pride for repairing it myself. You are really helping people out, Shack! THANK YOU.
DB that is great. Its so true. people can do more than they realize. They just have to take that step of faith get out of their comfort zone and they will surprise themselves, Congratulation on a job well done and thank you for viewing.
Thanks for your contribution to the hard working middle class people who don't have the funds to pay for plumbing services but are willing to learn from experienced people like for yourself. This was an excellent tutorial video which I put to good use and got the MXT07 replaced on our shower. Much appriciated! Robert
Robert this mean a lot Thank You.I always say people can do more than they realize if they gust take that step with a little guidance. It's my honor to help.
Watching and learning in 2023. You've given me the confidence to tackle the job myself. A thousand thanks!@@TheShackHome
Thank you so much. 😊Just now seeing this in 2023 and this has been so helpful. I’ll let you know how it goes 🙏🏾
Phoenicia Cloud my pleasure, I do hope all went well.
This helped a lot when our shower wouldn't shut off this weekend. Wiping with a paper towel got out a screw and bent washer that were still inside after I took out the old cartridge. Don't skip any steps.
I watched 3-4 videos besides this one, and this video was by far the best. I appreciate the details and how you compare the wrong cartridge and the list of tools supplies needed. THANK YOU! You gained a new subscriber!!
Mari G you are very welcome and thank you Mari I am truly great full to you for subscribing. I very happy my video helped. This is exactly why I do this. Not for the masses but for people just like you. If you have a question even if not related to a video if I can help I will who knows I may make a video on it.
The Shack Thank you! How about a video on replacing a shut off valve for toilet?
I have one of these 'vintage' valves in my dulplex rental home. I replaced the valve a few years back, but have never been able to adjust the temp easily over the past years. . . . .and it has been a hassle for my tenants. I will be replacing the valve once again, and thank you SO much for the very well done video and suggestions for matching the valve with correct unit. . . . and clear procedures with professional and detailed steps! You obviously know what you are doing, and are helping many older folks with your attitude and caring work!
Jan Grigsby
thank you for the kind words. That day may come when you'll need to replace the complete valve. these are good but very limited to the accessories for it, even for a rental. this was one thing I did when I renovated my rental near Huntington Beach (In 2010) I replaced all valves and updated to Moem. I'll be doing the same when I renovate 2 bathrooms in my house. Sometimes a little extra is worth it in the long run. Thanks for chiming in and thank you for viewing.
@@TheShackHome Thanks for the upgrade advice!!
Thank you sir for guiding me much appreciate it
I haven't replaced this in 20 years, so I finally found a video to help me. Yours was awesome!!!!
Thank you, for refreshing my memory
Thank u sooooo much!!!!! I’m 25yo and a female and I’m soo happy I did it all on my own with nobody’s besides your video of course! Jsut saves me $300. I literally got a quote today from a plumber and told me it was going to cost $295 to change the cartridge I was like well let me think ability and let me try changing it myself again. A friend tried changing it and realized he didn’t install it properly and didn’t push it all the way in so it was leaking, And so I nudged it a little bit and it went all the way in. I’m sooo happy!
Watching this now after finding a puddle under the shower area of my mobile home and narrowing the source down to my shower valve. Let it go so long because it was silent! The only thing I noticed was a small amount of mold on a wall about a year ago and it never reappeared.
Looks like my weekend taken...I will be fixing the leak! Thank you so very much for this video!
American meteorite fan well I hope all went well and didn't take too much of your weekend. You are welcome and thanks for viewing.
years dealing with this problem looking for the right parts and thanks to this video just fix my shower. thank you very much it was so helpful.
Your video was awesome!!! Thank you. I had the identical valve and my shower valve was hard to turn and really had to be cranked to shut the water fully off and when you ran the shower a lot of water poured out the tub spout still. I took off all the old parts and took them over to a local plumbing supply store (they are more helpful and knowledgeable than at Home Depot) and they helped me get exactly the right replacement parts and your video walked my step by step getting the job done efficiently, which is a rare case for any of my DIY projects.
Thank you thank you!!! Your video gave me the courage to attempt this myself! I did it! I had a freak out moment when the water kept coming and all my turning didn’t help! I decided to take it out and start from beginning. I went straight to comments in case the same thing happened yo someone else…someone said that it came “open” and sure enough as soon as I compared the old one to new one I found my problem. It’s so smooth and easy to use now. 👍🏼
Thanks man I really appreciate that you took the time to upload this. I'm a bit of a handyman but I'm not very experienced in plumbing. After watching this I feel very confident I can replace the one in my in-laws house.
Can’t thank you enough. The first time I installed this valve (based on other videos) it worked poorly then self-destructed after three months. I installed a new valve after watching this video and wow what a difference. It’s all in the details. Among other errors I think I had way over-torqued the valve the first time. I wish you a wonderful life and please know you are appreciated! And yes indeed the red dot goes down.
The intruction from the box said the red dot goes up. I don’t know why they don’t correct it. The company mixet should watch this video .
Excellent video. Especially how he describes the differences in the two Mixit Cartridges. I also like the fact he cleaned everything (especially the on/off knob and hot/cold water leaver) prior to putting them back on. Regarding the white sealant around the Eustachian.. there's 2 schools of thought. One is to seal it as this gentleman did. However the 2nd school of thought is by sealing it any water caused by a leaking valve won't be able to get out and will ruin the wall behind. This is a similar thought to sealing a toilet to the floor.
A good method to clean inside the water delivery pipe is to use an old toothbrush.
While he uses Plumbers Grease to grease the inside of the water pipe and the Mixit Cartridge.. most DIY people won't have this. One can use WD-40 which is fish oil based and won't hurt either the rubber O-ring or any component. One can also use K-Y Jelly which is glycerine based and water soluble.
If you wish to save money and do it yourself you can simply pull out the old cartridge and clean it. Use quad ought (0000) steel wool on the Eustachian and Bonnet nut to clean them. Use WD-40 and an old toothbrush to clean the plastic Lever and Knob. Use WD-40 and a paper towel or soft (lent free) cloth to clean the Plumbers Grease off of the Mixit Cartridge. You'll note that over time minerals in the water causes the Plumbers Grease to become sticky. This is why I prefer WD-40 or K-Y Jelly. You can also completely unscrew the Cartridge and use a toothbrush and WD-40 to clean all the threads... then simply reassemble it. Use the 0000 steel wool or 120 grit sandpaper to clean the brass rings which go onto the Cartridge.
Many times all that is wrong with the Mixit Cartridge is that the rubber O-Ring is bad and letting water leak... this and the sticky old plumbers grease. You can simply buy an assortment of O-Rings from Harbor Freight Tools for $5.99 here's the link: www.harborfreight.com/225-piece-nitrile-o-ring-assortment-67677.html
Simply put on a new rubber O-Ring and reassemble according to this gentleman's directions. I've saved a lot of money by cleaning all the Mixit cartridges in my rentals this way.
Note: WD-40 means Water Displacement 40. It was invented in San Diego in the 1950's for the aircraft industry and military. They needed an product to displace water and stop parts from rusting and corroding. It took them 40 times to get the ingredients right.. and the basic ingredient is fish oil.
I think you meant escutcheon. If you watched how he applied caulking on the rim of the escutcheon, you would see that he did not apply any on the bottom part. That is to allow any water from a leak that accumulates behind the escutcheon to flow down to the drain below. I have seen a similar video and the plumber said to position the hole on the stem with the red mark on top not below. Which one is correct?
Thanks so much for posting this. I needed to replace knobs in both bathrooms and one cartridge. This was super easy to follow and very helpful
Makes sense to me. Thanks for the info. I so happy you set me straight. So now I don't have to stand on my head anymore with my tongue in the most awkward position in a gallant effort to ensure the seal is contiguous and complete all while trying to see under the damn things. What a relief!
Thank you for the great film. I installed today a new stem MXT07, following procedure described. The only thing, the stem didn't go till the necessary position, though I cleaned and applied the plumber grease. I used a muffler hammer and knocked on it, it went in the pipe. Actually many people complain that the stem doesn't go in and think that it is a wrong one, thought it is that muffler hammer which is needed to complete the project. I also added a new handles set. Looks great! Thanks a lot again.
I was going crazy trying to find out which valve I had. I was about to give up, then I found your video. I have the same one, thank you for the video.
Adriana L.
you are very welcome I am happy to help.
Thank you very much for this video!!! I followed all the steps and tips. The most useful were using the MXT07 and the plumbers grease. It made everything go smoothly. I highly recommend using your videos.
Patrick Bolton
It always humbles me to hear this. I'm so happy you were successful. You are very welcome and thank you for viewing.
I used to work in plumbing years ago. I have some good skills. Just never installed a mix-it, thanks again.
You’re awesome in explaining the right part and keeping us from making a mistake. You’re a good teacher, thanks.
I don’t remember changing this part 2 years ago
Your guidance through this process is greatly appreciated. Couldn't have done it without you. 🙌😊
GP3 p no you take all the credit I hopefully just gave some guidance you did all the work. congrats
Thank you! because of where I live, calling out a plumber costs a fortune. I did this all by myself! And it took no time at all.
Leslie you are very welcome That is why I do this you can do more than you realize. Great job thanks for viewing.
I have that same shower valve that just snapped! What a god send❤ thanks
ymararma my pleasure. Thankd for viewing.
Thanks for the video sir. This was my project today. It wasn't simple at all but because of your guidance, I managed to finish and complete the job, saved me big bucks from hiring a overpriced plumber. Thanks again and keep up the good work.
Vista114
you are very welcome and congrats on a job well done. Have a night out or just have a cold one with the money you saved. Thanks for viewing
Yep, I bought a "similar" cartridge at Home Depot. It "looked" identical. Very long story short, I went to Lowe's today and got the MXT07, 10 min job total and all worked out perfect! THANK YOU!
MrAsphault your very welcome. Glad it all worked out fine. thanks for watching.
Nice video! Very thorough and descriptive. Left me with no unanswered questions! Thanks!!
After 30+ years of living in this house, we were the first owners, I always thought the dumb plumbers had plumbed my shower backwards. After installing the new cartridge per your instructions (red dot down) it works like it should, so yes the red dot direction does make a difference. Also, the new O-ring must have been a bit larger and I could not get it to slide in. I got a small deep socket so as not to be hitting the brass stem (socket resting on white plastic) and tapped it in with a hammer. Thanks so mcu for the video.
You saved me time and lots of money. Just replaced my cartridge today because the old one was leaking. Thank you!
My pleasure Frank good job and thanks for viewing.
Did my research and fixed it myself in 30 minutes or so. Plumber estimated $200. I tell you, RUclips professors are underestimated bc my RUclips education is treating me well!
I followed these instructions exactly. The red dot went down. (Opposite of box instructions) great video!
I was was thinking that this guy is giving incorrect instructions since he says red dot goes down as opposed to going up as noted on the box
Thank you. Because of you I am able to fix my faucet and save money by having someone else do it.
Thank you for making this video. It worked well for me and I didn't have any trouble. My cartridge was MX-1 and it fit fine. I really appreciate these DIY videos, as they help novices like me. I had a plumbing accident earlier this year that caused a flood and required $9k to repair, so I was hesitant to do anything more myself again (it's like I had plumbing PTSD). This little success helped rebuild my confidence.
Tom thank. You and I’m glad to Help. So true its one step at a time then your off running. I’m honored to help in the small steps. Job well done. You did great.
@@TheShackHome Thanks. BTW, re the cartridge fit, I spoke too soon. It turned out to be super hard to turn. I tried 3 different cartridges (Mixit, Danco, Ace). None fit correctly. Decided to hire a plumber to replace the Mixit valves with Moen valves. To save money, though, I did cut holes in my drywall to facilitate the plumbing work. That was also a new and kind of tricky experience for me.
@@tomjoht Unfortunately that is the final outcome in some cases. There are time a new cartridge just won’t work and its time to update. They don’t last forever. Sorry to hear it was a more costly endeavor.
Hi in 2022 soon 2023 this vid helps me thank you 👍🏿😷👍🏻🇨🇦🇵🇭🇺🇲
MrJojo2go my pleasure. Thanks for viewing.
Thank you, I have the exact valve stem which is not common and this video helps tremendously.
Kha Le you're very welcome
You sir, are a gentleman and a scholar👍😎thanx 4 posting!
You're the BEST! Saw many of these, many sub-par, but yours is the very best of the bunch!. I watched several times to be sure, then badda-bing-badda-boom--I did it! SO happy you made this video!
Allen that's a humbling comment. Thank you. I never consider myself the best there are many truly great plumbers out there but I've been blessed with the ability to do a few things and through that if i can help others......i'm happy to do so. Thank you again and thank you for viewing.
THANK YOU THANK YOU - we couldn't have figured out how to fix our leak if it wasn't for you! This video was so informative & helpful showing every step of what to do. You're the BEST, thank you so much!!
Laisa Nielson
I'm humbled. You are very welcome.
Ok, so somewhere I messed up, because turning it on & off has been an issue, ha ha. And so I took off the handle - it's an old one, so I'm wondering if I need to buy a new one, and I turn the shower on & off with the pliers. But now, I'm noticing that the copper piece is disappearing - is that when it's on Off position or have I messed it up somehow?? 😬
wow! you are seriously a life saver! I have a home inspection coming up this weekend for my buyer of the house, I did a thorough inspection by myself and noticed that my guest bathroom was leaking from the knob.. i was about to call a plumber to take a look at it but decided to go on RUclips route I'm glad I did! only spent $60 total for the stem, shower wall trim kit and the shower valve opener. I could've spent few more hundreds of $$$ if it wasn't for you. your video is amazing and i love the detailed explanation of the steps. keep up the good work!!!
bert de guzman
Thank you. If I had $5 for every person this helped I could of retired off this 1 video. That is why I do this is to help. not profit. I know people can do if they just try. I'm very humbled. Hope the inspection went well. thanks for viewing.
Great video! Now to go and change the cartridge in our shower. Thanks for posting!
Best video and good 'tricks' for this type of valve. Gave me the confidence to do it myself!
Andy this is exactly why i do this. I'm so glad you did it yourself. People can do more then they think. Just need a little helpful push sometimes. Thank you for the kind words and thank you for viewing.
I have three mix it valves I need to replace.two of them I can't even turn with two hands! Your video was SO informative, I'm confident in changing them out. Thank you so much.
kathy i know you can do it. Just make sure you get the correct ones. when you pull the old ones out set then next to the new and make sure they are the same. I'm happy to help thank you for viewing.
Best mixet cartridge replacement video by a mile. Fantastic tutorial
doug peters
thank you I'm humbled. I hope it was helpful and thanks for viewing.
Great video! I finally was able to fix my shower after months of it not working properly!
This is a great video and our home greatly appreciates it. Changed the master bath shower component and works perfectly. Now on to the next project. Greatly appreciated.
ZurHoll
i am truly humbled thank you. I'm happy to help. Good luck on your future projects and thanks for viewing.
Thank you Ray. Excellent instructional video - it helped me to fix our shower (after I removed the stuck valve). Best Regards, Ken
kenjpretell you are very welcome happy to help.
Great help!!! I really appreciate this video. It made the repair so much easier having the knowledge going into the task!!! Thanks again!!!
Thank you so much! I was at my aunt's house and had to replace the cartridge and this was a lifesaver
Eduardo Vasquez
I am so thrilled to have helped but YOU did all the work congrats. thanks for viewing.
Very well done. Thank you. This Vid is step by step which is very helpful for us non-pro DIYers
Very helpful video- thank you! I almost hired a plumber to fix my leaky valve, but your video convinced me that I could fix this myself, and I did. And installing the replacement cartridge was actually pretty easy, thanks to the detailed instructions and info from this video.
One point to emphasize that I am not sure if it was mentioned or not- the cartridge comes from the factory in the "Open" position. Turn the valve to Closed before you test the water line for any leaks, or you will be freaked out like I was when you turn your water main line on again, and water comes gushing out of your faucet. And note that you will have to turn the valve about 50 times to get it to the Closed position.
Jim this is exactly why I do this. People can do more than they know just need to step out and give it a try. Of course you need to be comfortable doing so but you are the perfect example of those who do and are successful. Thank you Jim I truly appreciate your comment and viewing
This video helped me a lot, thank you very much!
OzInvesting you are welcome and thanks for viewing.
Thank you for sharing your wisdom sir! Liked & Subscribed! Going to fix my broken shower knob.
Well explained & You made it look super easy. God Bless you.
Thanks for your know how man! I did buy the wrong one and researched because I knew it was wrong to force it in!
Excellent video,easy to understand, made the repair manageable. Thank you
Anthony Vaccaro Thank you sir, you are very welcome. Thank you for viewing.
Thank you so much! I was looking for the same type of set-up that I have and I finally found you. Thanks so much!
goldenrist you are welcome Thank you for viewing.
This video saved the day. It is also well very well done. I did not replace my valve but seeing this video I was able to remove the gunk freezing the hot cold arm up. and reinstall it in the correct fashion. And wallah now I can adjust the hot and cold again easily. thank you
Hi thank you so much sir .i fixed my tow bathroom because i watched your video God Bless you
Thanks a million, sir! I would just add the o ring rubber is a bit round so I used the rubber Mallet to hammer it in gently and worked well!
Great video. This helped me realized that I may have gotten the wrong cartridge (indention you talked about) because my temperature knob spins non stop but my water flow works perfectly fine
Just changed my shower stem. Thanks for the help
david stoneits my pleasure thank for viewing.
I agree with you about the Mixet valve, I need to replace it with a more durable valve.
Thanks so much for your reply!
Man your video was perfect. You saved me a lot of money. Thank you 🙏🏻
SJA you are welcome. I'm happy to help. Thanks for viewing.
Thanks i was able to replace it myself due to this video! Got replacement at lowes.
Excellent video, don't know why I stumbled into other videos first which were giving wrong information or not specific enough. Thankfully, I found yours and was able to get hot and cold water from my shower.
It wasn't too easy as the circumference of the back part of the replacement cartridge was a tiny bit bigger (unnoticeable to the bare eye) than the old one. I ended up replacing the plastic washer located on the back with the one that came on the new one and using the whole old back part on the new cartridge.
Recardo your a true handyman. You did just what most fo us would do and fix it how ever it needed fix'n good job.
Ancestor, thankyou for your video it has helped my fam .
Thanks so much! Helped me with my shower valve.
Brett you're very welcome. I'm honored it helped
Thank you! I replaced it with a new one exactly like you said, but it was still hard to turn the hot & cold handle. I found out that if you loosen the chrome cover sleeve, that goes on the main pipe over the cartridge, a little bit at a time (not loose) it will turn easier.
Thanks sir, great video. Helped a whole lot. Much appreciated.
This really helps, just changed the old stem in my home, thanks a lot.
Leon you are very welcome and thank you for viewing.
Wow, great video. We had the wrong valve as well. Sucks how they are so similar too. Thanks for making this!
ArrowSpaceMan
You are welcome. Happy to help. Thank you for viewing
What if my valve stem continues to rotate. The hot and cold. Doesn’t stop at any point left or right.
Excellent video! Thank you for doing this.
Nonelse you are welcome
Brother! You gave me courage to continue my replacement. Will be trying it out tomorrow morning.
Tiredgeek wish you success and thank you for viewing
@@TheShackHome I replaced it! Works great :) Thank you again.
@@Tiredgeek you are very welcome.
I found this video very helpful. Thank you.
Thank you Dustin glad it was helpful.
Watched your video to replace our shower mixet valve, thanks, your video was very helpful! i just subscribed to your channel, thanks again!!
millerlitedrinker so glad to help, thank you for subscribing I hope i can inspire and help more in the future.
Very simple, thanks for posting the video.
lowrider you are welcome and thank you for viewing.
Honored it was helpful.
thank you for the help
I am not mechanically inclined. but this video got me through it.
D Ride i don't ask for channel support, donation and I'm not sponsored (yet). This is exactly why i do this. I want to encourage people. they can do more then they know. Thank you. I'm glad it was helpful and you had a successful outcome. Thank you for viewing.
Thank you very much👍. Just did this today.
Other than your advice about the red dot, this was very helpful.
My instructions for the MXT07 say the red dot must point up. Is that what you're seeing too?
You helped me IMMENSELY with this video! I had a plumber out to do this for me only because I was unable to loosen the nut. When he finished he said it was "not much better" and I should tear open the wall and replace the valve. I KNEW they don't really go bad, only the cartridge. So, I went to Home Depot and got the correct cartridge. Sure enough, he had installed the wrong cartridge. You mention at about 5:05 on this video that you wished you had a picture of the difference in the two cartridges. I have one for you all! New cartridge, greased up and installed and it works like new. (Was completely unable to turn it prior to this, AFTER plumber left.) Can't seem to share in the comments, I will try to get it to you. Thanks again!
Kathy Schlesselman
Thank you. I don't think I can post a pic in the description and I would have to redo the video to put it in. One of the down falls with RUclips. Wish that would change we could update or correct thing without completely redoing the complete video. Although I might add a link to a pic for side by side of the 2 cartridges, You could email me direct and i could try to do that. Again thank you for the comment and thank you for viewing.
@@TheShackHome , if you can send me your email address (I don't see it here) to kathy.schlesselman@gmail.com, I'd be happy to send you back the pictures. Thank you again!
thank you so much with the detailed video. much appreciated
Just watched your video, ran to Home Depot for the parts and plumbers grease and will install tomorrow. Having the exact problem you spoke of...my 89 year old mother in law u able to adjust the water because it is too hard to turn. Thank you!
40redfox40
you are welcome i hope it all went well. thank you for viewing.
The Shack it worked out perfect. Lived here 25 years and first time I changed it out...should have done it years ago. Thank you.
I had a professional plumber doing it. Two visits a week apart. First visit, he removed the part, ordered it. Second visit he tried to install the cartridge, it didn't fit, so he combined parts from existing cartridge and the one he ordered , rebuilt it and installed (wasn't easy). $289.00.
Thanks for this video. Really helped me.
William you are welcome and thank you for viewing.
Good job!Good presentation!
Red dot actually goes up. IIRC, it also says "up" in tiny print.
He does it right but doesn't say it. Do not put caulk on the lower 1/4. It allows it to drain if water ever got trapped.
thanks for the video... so theres 2 different models.. the best bet is to take it out and check to see if you currently are using a brass backing or a plastic one.. use the same one you have👍
Excellent video
This video is amazing, I would just like to add one more thing if there's a plumbing supply store near you I highly suggest you go there because they should have the actual mixit cartridge that comes with a brass fitting on the back, instead of the plastic ones that come from Home Depot and Lowe's. Also make sure you tighten up that screw on the back of the cartridge. After I installed mine it worked for about a week and then it wouldn't shut off. After taking it apart I realized the screw and gaskets were left inside the valve along with three other screws and three other gaskets all the way in the back from previous cartridge replacements.
That happened to me too just now I , I shit the water off took the cartridge out and the water was still flowing out the pipe , I look inside and the screw that goes on the back of the cartridge had fell off and was stuck inside the pipe , I put the cartridge back in and took it out again and the screw came out of the pipe , I put everything back together and tried it out, hot water was on the left and cold was on the right idk how that happened 🤦🏻♂️
Thank you! I will try this and follow up if I did great or not haha!
Nice instructional video!!
Big help.Thank you
This video was a godsend, thank you sir
I Shadow People You are very welcome. Thank you for viewing.