Update on the video! after a few days the rough idle was back on cold start only and I've found out that my CCV valve was broken aswell! See that video here: ruclips.net/video/w0sGD_DH7Cc/видео.html Installing a stage 3 intake here: ruclips.net/video/SalVsl88k6E/видео.html
Mann god bless you I swear to god with out you I was ganne sell my car for 500$ because I been forcing this problem for along time ago but after I watched this I did everything you said and it worked I wish I can meet you and give you a big huge Mann no word can explain my happiness thank you so much
Brooooo. You saved me thousands, the repair shop quoted me on some bullshit replacement.... these are the things ive done my self trying to solve the misfires, i replaced ignition coils,vanos solenoid,crank shaft sensor,new oil, new sparkplug, i even got the valve cover gasket replaced... and it sat there for 4 years... finally after watching this i did it my self this morning.. removing the front right wheel and removing the wheel well makes it a easier task! The bottom one had some particles, but the top nonreturn valve was filthy!!! I cant thank you enough!!!
My idle kept jumping up and down every single Red light and sometimes even turned off!!! I did EXACTLY this (my filter was DIRTY DIRTY DIRTY) and now it’s running brand new again!!! .. Thank you 🙏 god bless.
I wonder how many people have spent $$$$s replacing the VANOS solenoids but never checking these... probably a lot! Makes me wonder if you even need to change the solenoids either... Maybe just remove and clean them like this and keep the engine oil good and clean, should avoid all the expensive VANOS issues BMW engines are so famous/infamous for! This video could save people a lot of money on unnecessary parts! Very well done for showing us this tip 👌
Just bought my first bmw as always was worried they were money pits but after watching alot of RUclips videos for diy it looks manageable to maintain most things yourself
Boz 2011 i have seen steady rpms. Thats pretty steady. I do live in canada where our engines run at -35c on winterized gas. Tough for an engine to be steady from cold.
Thanks for covering this. My rough idle is not as severe as yours and does it momentarily on cold start ups. I already replaced my valve cover assembly, eccentric shaft sensor, ignition coils, spark plugs, vanos solenoids, cleaned MAF sensor, and changed oil to 5w30 instead of 5w40. I will be ordering new non return valves to replace them, regardless if they turn out to be clogged or not. Update: I replaced my non return valves today. I noticed both the motor and trans. were more smooth, so far. I only get the rough idle after leaving my car alone overnight, so I am gonna have to wait and check how the idle will be the next day after a cold start.
Rough idle can be caused by blocked engine crankcase breathers. The breather filters are built into the valve cover which will need to be renewed if this is the problem. When the engine is running remove the oil filler cap and remove it, if the cap is hard to remove or you hear any 'sucking' noise as you remove it then you have a breather problem.
This video got me subscribed.. i did my solenoids and it didnt solve my problem on my n52 e92, i would never knew about those filters man... thank you very much
If rough idle it's correlated with smoke when you floor it, check the O2 sensors, this was the culprit on my N52. Changed everything, vanos solenoids, coils, spark plugs, etc. Problem was Bank 1 pre-cat O2 sensor, NO check engine and NO fault codes...
Wow. So lucky to find this video!!! You described everything I have been struggling with! Same same problem here. Already replaced PCV, spark plugs, checked Ignition coils, cleaned and checked Vanos solenoids... Seems like one more thing to do is clean/replace these Vanos valves!!! Thank you so much for this video!!! Will be reporting soon!
After 6 months of chasing vanos codes and replacing parts for my rough idle I came across your video. Lo and behold I took them out cleaned them up, re installed and my car has the most stable and smooth idle! Was a little different for me as I have the n13 engine 116i. You are right there is not much if any information on these non return valves and how they affect the vanos system!!
Excellent. Yes, yours is the first vid I have seen do to mention the filters. Great tip. Cleaning the filters regularly may prolong VANNOS life and just help entire system. great tip, thanks
Sure nuff helped me out with the 08 528i. At first I had issues because I flipped the connections lol went back to look at the video and realized my mistake. Runs good. This is why I love RUclips, just search and u can find. Edit Saved a lot also on doing my own starter, that went out again. First time paid over 1200 bucks at a dealership. This time paid less than 200 for the part. Gained valuable knowledge about this car. Also did the coils, sparkplugs, cleaned the various filters and sensors and whola, runs like new.
Thanks mate, changed my banks solinoids twice still had problems so I pulled out the non return valves and they were full of grit. Cleaned them and now got a smoothe running engine. Cheers.
Change synthetic oil every 5000 miles to avoid this problem caused by burned paraffin sludge. Thanks for the good fix video! I never knew those filters were there.
I have Forte fuel system clean and full engine flush carried out at every service and I don't follow the BMW 20,000 mile intervals as shown on the dash count down, I stick to 13,000 miles maximum between services. No problems because of this and I cover 250 miles a day
Bro I’ve done everything to my car I’ve changed both vanos ,camshafts sensors ,spark plugs ,coils ,engine flush ,injectors ,intake gaskets ,ppc valve, breather ,hoses ,clean throttle body I watch a ton of vids going on a yr now trying to figure this problem out spent so much money . I going to try this out I hope it works . bless you bro . Wish me luck🤞🏾
Don't forget to check the valve from the engine cover I have a video for that as well and remember to reset adaptations before you start the engine. Good luck
Thanks man for sharing this video. I changed all the items you mentioned and have the same problem with rough idle. I am going to clean the filters and let you know the result.
Sir thank you so much for the video, i have exactly the same issue, we just cleaned the vanos intake and exhaust, but we have never seen this, What tools you use to clean this to avoid damage please ? Thanks again
Change your spark plugs to the new 4 electrodes on them, BMW changed the spark plugs without telling customers to fix the idle problem The new plugs are available at BMW to replace the single electrode one.. The bmw & Mini dr on youtube has just given out the info recently..
You don't have to believe everything from the net. Just think at this...how come the car was running normal without the new spark plugs before and now runs normal just with that spark plugs...kinda strange for me... but every one believes what they want...anyway my car idles perfect with normal spark plugs
Best video ever I've been searching for what was making mine do the same and there was a loss of power I haven't done it yet but Im almost 100% sure this is it... thank you for this video.
i don’t know if i have the same problem i only had it happen once (this morning) i started my car and it was jumping a bit then stopped shortly and was steady at 600 rpm’s, do you think i have the same problem or was it just warming up?
thank you! i just recently started seeing my car idle roughly and i was planning on overhauling my coils and spark plugs but i will try this first! How hard was it to remove the two filters?
Thanks for this video, I have been going crazy trying to figure out my rough idle and I've change literally everything but never seen anything about these filters, I feel this will finally do the trick, cant wait to perform this service, thanks again!
I took them out and they were completely covered and clogged, I cleaned them to like new conditions and unfortunately it didnt correct the problem I'm having, my car keeps throwing a p1415 code and it surges really bad on cold starts almost like it's out of gas and when slowing down or coming to a stop light or stop sign it surges and rpms drops to the point of stalling and then shoot up to idle and stay there, I'm stumped, please help if you can, I live my car but I'm told the point of getting rid of it.
@@rickt8325 try lambda sensors! i have same problem with my n53b30a ! changed bank1 o2 and its better now so will change other 2 sensors and nox sensor too and see how it runs! if won't fix theres ony one more last step left for n53 and its injectors :(
I have the same issue of rough idle making me go crazy tbh. Have an 002AFC code. Cleaned the maf, the map, the throttle body and changed the plugs and did an oil change and filter. May it be the return pipe of cvv? Thanks for the help (n46 engine on e92)
Man i went out to the garage for about 2 hours looking for those filters and i think i found 1 maybe. On the x5 2010 N52 engine is it in the same spot?
Great video. Does anyone know the position of the non return valves on a 2008 N43 318i. I've already cleaned the Vanos solenoids, but didn't know about these valves. Thanks.
From 9:48 to 9:56 idle is still rough as well as engine and car are still shaken hard. Do you know what the problem is? I have exactly the same problem.
I have a problem where coil number one loses spark. I changed the plugs the coils the vanos. But coil one will have spark minute then no spark another minute. any ideas what the problem could be.
I'm going to try this next on my n52! Iv already done Vanos solenoids CCV replaced with new cover CCV hose Crank positioning sensor Plugs No luck. Infact it got worse with new oem solenoids.. Do you have the oem part numbers for the gaskets?
Thanks for watching! Thx, I don't have the e90 anymore you can watch my other videos to see the cars that I've changed or what I worked on the E90. Greetings from Germany 🇩🇪😀
My 2007 x3 also chugs but has a really loud high pitcged squeal and does it all the time. Everything i found on it is that i need to replace the pcv vavle... which just so happens to supposedly be molded to the valve cover.. atleast from what ive been able to find out about it.. its creating a ton of suction and if i take oil fill cap off it stops squealing but will still chug just not as bad.. took it to bmw dealership and they said my valve cover is cracked.. didnt say where just that it would cost 2500 dollars.. there is no oil leaking tho. Which my dad a mechanic of u.s. domestic vehicle of 20+ yrs says there would be oil leaking out of a crack if there was one... there is some sensor on the top front of my engine that has had caulk rubbed all over the case and there was a bit of oil in the plug part of same sensor.. cant find what the sensor is to replace it tho.. for all i know that could be the thing i need to fix..
dude, I never ever heard in my life about vanos filters! eather you have more infos than regular people (hobby mechanics) or you just made it up! im going to google it!
2019 brought BMW X3 person sold at a high discount because he could not remove check engine. Saw your video and did exact what you posted and cleared it right up. Fix cost about 3.00. You are the best God bless you for posting.
Bro, no one has ever showed this information about rough idle, i will try it. I have a question, why does a car hiccup in cold start and makes the car have high idle when turn on the ac or shit to drive/reverse? BMW E90 N52 No codes are showing, and no engine light as well. Also I've changed every gasket like how you did, new spark plugs, new compressor, new pcv
@@ArkadyRenko1 it was the maf sensor on my Intake that went bad, no check engine light but it started like shit and would sometimes stall going from 2nd to first I replaced my sensor and it runs like new
You don't have this set up on the diesel engine. If your idle is not steady you have to check your EGR system (valve, return pipe) injectors or dpf filter
If you're talkin about an e92 or something like that go for the Foxwell nt530 I was able to do everything on my car scan it on test on it reset it it was only like a hundred seventy bucks best purchase ever made
I got the rough idle on my E83 rite now and changed the plug and coils then the steering pump recently...thinking it’s still gonna give a rough idle when I go start it up thinking I need to clean or replace these filters along with the vanos and see if that is my problem as well these N52 motors are a big pain but when you get to changing parts you become familiar with everything in your vehicle good tips on the video thanks !! How long did the job take you to clean these 2 filters?
I just noticed when I parked, put it in park my rpm dropped. Felt like it was going to shut off. May need to clean mine as well. What did you use to clean them?
Hi! I got a E92 bmw 2007 , 2.5i 92.000 miles on the clock..The problemI got is the engine just cut of at lower speed. I changed the VANOS solenoids the oil filter and the oil, but nothing happend, engine cuts of at lawer speeds.Can you give me some advices please! , I see you know all about this tipe of engines.Thanks allot!!!
Usually when the power is cut at lower rpm is a vacuum leak, or fuel system error. At high rpm is always electric. Check the vacuum hoses from the engine cover to the intake, oil separator, maf sensor....
You only have bank 2 if your engine is a "V" engine (v6/v8/...) system too rich can mean MAF sensor bad, bad injectors, fuel pressure too high, O2 sensor defect usually the first one before kat. This are just Infos, you need to let the car to be checked by someone who can give you a diagnosis...
Update on the video! after a few days the rough idle was back on cold start only and I've found out that my CCV valve was broken aswell!
See that video here: ruclips.net/video/w0sGD_DH7Cc/видео.html
Installing a stage 3 intake here: ruclips.net/video/SalVsl88k6E/видео.html
Pin this comment!
Same here,I've changed everything and still had the problem and almost give up...luckily I find this amazing video!Thx a lot! 😃
Mann god bless you I swear to god with out you I was ganne sell my car for 500$ because I been forcing this problem for along time ago but after I watched this I did everything you said and it worked I wish I can meet you and give you a big huge Mann no word can explain my happiness thank you so much
Glad to help! Enjoy your car! 🚙👍
Wow that's awesome!
You’ll have to fly to Russia for the hug😀
mann i howe this problem on 530d rmp droping cliking
How does a rough idle sound?? Mine just keeps moving from 1500 to 1700 . Up and down up and down
Brooooo. You saved me thousands, the repair shop quoted me on some bullshit replacement.... these are the things ive done my self trying to solve the misfires, i replaced ignition coils,vanos solenoid,crank shaft sensor,new oil, new sparkplug, i even got the valve cover gasket replaced... and it sat there for 4 years... finally after watching this i did it my self this morning.. removing the front right wheel and removing the wheel well makes it a easier task! The bottom one had some particles, but the top nonreturn valve was filthy!!! I cant thank you enough!!!
What misfire problems were you having one bank or both ?
@@RRSAutoempireI’ve got bank 1 and 2 gonna try this on the weekend and I will respond. Did you give this a try ?
My idle kept jumping up and down every single Red light and sometimes even turned off!!! I did EXACTLY this (my filter was DIRTY DIRTY DIRTY) and now it’s running brand new again!!! .. Thank you 🙏 god bless.
Glad that this worked out for you!
Did this solve the issue bud? Or did you have to fix something else?
I wonder how many people have spent $$$$s replacing the VANOS solenoids but never checking these... probably a lot! Makes me wonder if you even need to change the solenoids either... Maybe just remove and clean them like this and keep the engine oil good and clean, should avoid all the expensive VANOS issues BMW engines are so famous/infamous for! This video could save people a lot of money on unnecessary parts! Very well done for showing us this tip 👌
Just bought my first bmw as always was worried they were money pits but after watching alot of RUclips videos for diy it looks manageable to maintain most things yourself
Absolutely! And welcome to the club! Enjoy your car! 🚙👍
Thats the most steady needle i have ever seen. Well done sir!
Wow, never seen steady rpm before?
Boz 2011 i have seen steady rpms. Thats pretty steady. I do live in canada where our engines run at -35c on winterized gas. Tough for an engine to be steady from cold.
One of the best videos I’ve seen for fixing rough idle issues.
Awesome tip, thank you from every N52 person. Short, to the point, filmed-well enjoyed it. Never saw Anything about these filter-things. Very cool.
I don't have any rough idle but am gonna clean mine as a precaution. Thanks buddy, first vid with such a great information.
Did you end up cleaning yours? I’m getting ready to do the same 2011 528i with the inline 6🤙🏽
@@CorbinWilliams Yes I did and it actually worked. I also replaced spark plugs. But that bout it.
I tried and tried, I couldn't get any purchase on those valves. I don't know how you did it, hats off to you man.
Thanks for covering this. My rough idle is not as severe as yours and does it momentarily on cold start ups. I already replaced my valve cover assembly, eccentric shaft sensor, ignition coils, spark plugs, vanos solenoids, cleaned MAF sensor, and changed oil to 5w30 instead of 5w40. I will be ordering new non return valves to replace them, regardless if they turn out to be clogged or not.
Update: I replaced my non return valves today. I noticed both the motor and trans. were more smooth, so far. I only get the rough idle after leaving my car alone overnight, so I am gonna have to wait and check how the idle will be the next day after a cold start.
Did you solve your rough idle?
I’m assuming your issue was to do with injectors
Have you solved the cold start rough idle?
Rough idle can be caused by blocked engine crankcase breathers. The breather filters are built into the valve cover which will need to be renewed if this is the problem. When the engine is running remove the oil filler cap and remove it, if the cap is hard to remove or you hear any 'sucking' noise as you remove it then you have a breather problem.
Were is the oil filter cap 528i 2008
Isn't that only on N53? Believe N52 has the CCV attached to the inlet manifold
The CPV valve is built into the valve cover! Rock Auto LEAST EXPENSIVE by far!!
@@electrotx This ^
I removed the oil filler cap but it is not sucking air at all.
This video got me subscribed.. i did my solenoids and it didnt solve my problem on my n52 e92, i would never knew about those filters man... thank you very much
So did you fixed it with this then ?
@@alvernhem nope, i had to change one of four O2 sensors, had to diagnose it to know wich one was bad
@@design2drive thanks but did you replaced the check valves or not ?
@@alvernhem nope, they were clean..
@@design2drive Ok thanks
If rough idle it's correlated with smoke when you floor it, check the O2 sensors, this was the culprit on my N52. Changed everything, vanos solenoids, coils, spark plugs, etc. Problem was Bank 1 pre-cat O2 sensor, NO check engine and NO fault codes...
Good to know...thx for the info 👍
Wow. So lucky to find this video!!! You described everything I have been struggling with! Same same problem here. Already replaced PCV, spark plugs, checked Ignition coils, cleaned and checked Vanos solenoids... Seems like one more thing to do is clean/replace these Vanos valves!!! Thank you so much for this video!!! Will be reporting soon!
Hey. Do you have part number of PCV valve for N52 3.0L gas engine?
After 6 months of chasing vanos codes and replacing parts for my rough idle I came across your video. Lo and behold I took them out cleaned them up, re installed and my car has the most stable and smooth idle! Was a little different for me as I have the n13 engine 116i. You are right there is not much if any information on these non return valves and how they affect the vanos system!!
Excellent. Yes, yours is the first vid I have seen do to mention the filters. Great tip. Cleaning the filters regularly may prolong VANNOS life and just help entire system. great tip, thanks
Thank you 💯💯💯 Great work I'm gonna try it on my N52 as soon as possible. You are the only one who shows it properly.
Sure nuff helped me out with the 08 528i. At first I had issues because I flipped the connections lol went back to look at the video and realized my mistake. Runs good. This is why I love RUclips, just search and u can find.
Edit
Saved a lot also on doing my own starter, that went out again. First time paid over 1200 bucks at a dealership. This time paid less than 200 for the part. Gained valuable knowledge about this car. Also did the coils, sparkplugs, cleaned the various filters and sensors and whola, runs like new.
Thanks mate, changed my banks solinoids twice still had problems so I pulled out the non return valves and they were full of grit. Cleaned them and now got a smoothe running engine. Cheers.
Change synthetic oil every 5000 miles to avoid this problem caused by burned paraffin sludge.
Thanks for the good fix video! I never knew those filters were there.
I have Forte fuel system clean and full engine flush carried out at every service and I don't follow the BMW 20,000 mile intervals as shown on the dash count down, I stick to 13,000 miles maximum between services. No problems because of this and I cover 250 miles a day
I literally change it every 3000 just cause I’m being extra cautious. Any idea when tranny fluid should be changed?
Bro I’ve done everything to my car I’ve changed both vanos ,camshafts sensors ,spark plugs ,coils ,engine flush ,injectors ,intake gaskets ,ppc valve, breather ,hoses ,clean throttle body I watch a ton of vids going on a yr now trying to figure this problem out spent so much money . I going to try this out I hope it works . bless you bro . Wish me luck🤞🏾
Don't forget to check the valve from the engine cover I have a video for that as well and remember to reset adaptations before you start the engine. Good luck
@deeyomoma did you find the problem?
Nope still the same
Thank you from France!
I cleaned the vanous cylinders today and still have a rough idle, I will try this tomorrow hopefully it works.
Thanks man for sharing this video. I changed all the items you mentioned and have the same problem with rough idle. I am going to clean the filters and let you know the result.
Results ?
Good job Man, everything is straightforward to the point. Liked and Subscribed.
The best explaination I have seen on youtube. Keep up the good work. I have theh same problem with my e92 325i N53. I will take care of it now.
The knowledge of the filters is very good.👏👏
Sir thank you so much for the video, i have exactly the same issue, we just cleaned the vanos intake and exhaust, but we have never seen this, What tools you use to clean this to avoid damage please ?
Thanks again
Thank you. I checked and they were completely clogged.
Good job my brother!!!!!!!
By any chance do you know where the map and sensor is at ? Not the one on top of the manifold
Change your spark plugs to the new 4 electrodes on them, BMW changed the spark plugs without telling customers to fix the idle problem The new plugs are available at BMW to replace the single electrode one.. The bmw & Mini dr on youtube has just given out the info recently..
You don't have to believe everything from the net. Just think at this...how come the car was running normal without the new spark plugs before and now runs normal just with that spark plugs...kinda strange for me... but every one believes what they want...anyway my car idles perfect with normal spark plugs
This doesn’t fix the idle issue 🤦🏼♀️ cars were fine before..
Thank you for the information.
I have a quetion. What's the lenth of the extension?
How long is total length?
T40 + extension + wrench?
Best video ever I've been searching for what was making mine do the same and there was a loss of power I haven't done it yet but Im almost 100% sure this is it... thank you for this video.
Update please....
Why didn’t I see this video before. Thanks. I. Well we had no idea. This issue has been hunting me for 1 yr driving me nuts
Ty you for this video. Question do you know if the n55 motor has those bolted filters
I remember doing this to my car and thankfully they were pretty clean
i don’t know if i have the same problem i only had it happen once (this morning) i started my car and it was jumping a bit then stopped shortly and was steady at 600 rpm’s, do you think i have the same problem or was it just warming up?
thank you! i just recently started seeing my car idle roughly and i was planning on overhauling my coils and spark plugs but i will try this first! How hard was it to remove the two filters?
Great video, well done, really straight! I have an N52N in a 125i and want to do this job. Brilliant mate, spot on!!
Dear bro could you please tell what type of screwdriver and how long can do easily
Thanks for the vid. I just bought an e60 and it has a wonky idle. Trying this today
Great info
Great result
Great video.
Well done
Thanks for this video, I have been going crazy trying to figure out my rough idle and I've change literally everything but never seen anything about these filters, I feel this will finally do the trick, cant wait to perform this service, thanks again!
let us know how it goes, I am having the same issue after replacing valve cover to fix the oil burning issue.
I took them out and they were completely covered and clogged, I cleaned them to like new conditions and unfortunately it didnt correct the problem I'm having, my car keeps throwing a p1415 code and it surges really bad on cold starts almost like it's out of gas and when slowing down or coming to a stop light or stop sign it surges and rpms drops to the point of stalling and then shoot up to idle and stay there, I'm stumped, please help if you can, I live my car but I'm told the point of getting rid of it.
@@rickt8325 try lambda sensors! i have same problem with my n53b30a ! changed bank1 o2 and its better now so will change other 2 sensors and nox sensor too and see how it runs! if won't fix theres ony one more last step left for n53 and its injectors :(
I had the same issue on my n62 v8 4.8. It was the Crankshaft Position Sensor
Hello dear.. was the same failure? How you fixed ?
Hi if my 2009 535i X will the vanos lower my oil pressure if they are dirty or could the timing have jumped
what product did you use for the cleaning part...ty!
For carbon build up and such, WD-40 and scotch brite pads (the green ones) work very well.
I have the same issue of rough idle making me go crazy tbh. Have an 002AFC code. Cleaned the maf, the map, the throttle body and changed the plugs and did an oil change and filter. May it be the return pipe of cvv? Thanks for the help (n46 engine on e92)
Would this be related to a P0012 & P0015 code? I’ve replaced the Vanos solenoids but I still get a rough idle when I start the car
Great. Good for you man.
Hey, what size T-socket did you use?
T-30?
Didn't know about this one! Nice job!
What do I do if I over strip the threads when I retightend ????? 😱😱😱😱
Is there an alternative to clean the valve as I don’t have a air compressor?
I was thinking to use carb cleaner.
Wil work as well, you can use a blade as well to clean the filter
Great video, thanks a lot, going to remove and clean mine out after oil change.
Man i went out to the garage for about 2 hours looking for those filters and i think i found 1 maybe. On the x5 2010 N52 engine is it in the same spot?
Great video. Does anyone know the position of the non return valves on a 2008 N43 318i. I've already cleaned the Vanos solenoids, but didn't know about these valves. Thanks.
On your engine you have no access to the valves, are in to the cylinder head.
Thanks for the info! I will try this today!
Have the same problem but car went into limp mode. Earlier it started 3 times and then died. Now im waiting for the mechanic diagnosis
Hello!What cleaner are you used for these filters?Please write me answer
I used brake parts cleaner and razor blade to clean everything
@WarpDriveM thank you for answer!
It’s a great educational video my friend.
From 9:48 to 9:56 idle is still rough as well as engine and car are still shaken hard. Do you know what the problem is? I have exactly the same problem.
I have a problem where coil number one loses spark. I changed the plugs the coils the vanos. But coil one will have spark minute then no spark another minute. any ideas what the problem could be.
I'm going to try this next on my n52!
Iv already done
Vanos solenoids
CCV replaced with new cover
CCV hose
Crank positioning sensor
Plugs
No luck. Infact it got worse with new oem solenoids..
Do you have the oem part numbers for the gaskets?
Do i have these on my BMW E90 318i lci?
Great video! Thanks for posting.
This, is a great video man I appreciate you making putting the effort to it. I have a 07 bmw 328xi wogon and I wonder if my have the same filters?
Yes the filters are the same.
I’m still struggling to find the same filter as you though
Nice car and great video, thank you!! From Los Angeles, CA
Thanks for watching! Thx, I don't have the e90 anymore you can watch my other videos to see the cars that I've changed or what I worked on the E90. Greetings from Germany 🇩🇪😀
Does m54b22 motors have non return valve ?
Thanks a lot for the effort, just one question what do you use to clean those?
Thx. I've used brake parts cleaner and a razor blade
I can't find the part number for that product
My 2007 x3 also chugs but has a really loud high pitcged squeal and does it all the time. Everything i found on it is that i need to replace the pcv vavle... which just so happens to supposedly be molded to the valve cover.. atleast from what ive been able to find out about it.. its creating a ton of suction and if i take oil fill cap off it stops squealing but will still chug just not as bad.. took it to bmw dealership and they said my valve cover is cracked.. didnt say where just that it would cost 2500 dollars.. there is no oil leaking tho. Which my dad a mechanic of u.s. domestic vehicle of 20+ yrs says there would be oil leaking out of a crack if there was one... there is some sensor on the top front of my engine that has had caulk rubbed all over the case and there was a bit of oil in the plug part of same sensor.. cant find what the sensor is to replace it tho.. for all i know that could be the thing i need to fix..
At 1:40 u almost pointed to the sensor im talking about.
To check if the solenoid is the issue you remove them and then turn the car on ?
No, do not start the car with any parts removed! Oil will pour out everywhere
@@WarpDriveM I cleaned them and it’s doing it more often lol helpppp
dude, I never ever heard in my life about vanos filters! eather you have more infos than regular people (hobby mechanics) or you just made it up! im going to google it!
Haha...do so!
2019 brought BMW X3 person sold at a high discount because he could not remove check engine.
Saw your video and did exact what you posted and cleared it right up. Fix cost about 3.00. You are the best God bless you for posting.
Bro, no one has ever showed this information about rough idle, i will try it. I have a question, why does a car hiccup in cold start and makes the car have high idle when turn on the ac or shit to drive/reverse? BMW E90 N52
No codes are showing, and no engine light as well. Also I've changed every gasket like how you did, new spark plugs, new compressor, new pcv
Bad Mass air flow sensor also causes rough idle when cold start. That was my case.
Same here
Do you mean NOX sensors ?
@@ArkadyRenko1 it was the maf sensor on my Intake that went bad, no check engine light but it started like shit and would sometimes stall going from 2nd to first I replaced my sensor and it runs like new
@@krispytoast8804 Thanks for the info. That will probably be my next step if the non return valves didn't do it for me.
Is it normal for the car to idle but have a strong vibration? It’s not a rough idle per say but it’s like not as smooth as you’d expect
What did you use to clean it??
Ive used brake cleaner and some blades to scrape the burned oil
WHAT IF ONE OF THEM HAD ALOTTTT/FULL OF METAL SHAVINGS AND THE OTHER HAD NONE AT ALL??? AND METAL WHEN I CHANGED OIL
Is yours a Blue Water E90 328i, looks super nice
good explanation!
Did you suffer some powerloss before the solenoid were changed
Great video, i have the same Problems but 330 XDrive N57 , do you think if could be coming from the same part?
You don't have this set up on the diesel engine. If your idle is not steady you have to check your EGR system (valve, return pipe) injectors or dpf filter
good video, i have a 120i 2006 2.0, code 2a83, have filters too?
If your car is equipped with vanos yes...but I think your car doesn't have vanos because has throttle body
Can you tell me what is a good scantool for the bmw, not to expensive
You can download for free Inpa from a lot of forums. You need to buy just a K+Dcan cable (aprox 20$) and you are set.
If you're talkin about an e92 or something like that go for the Foxwell nt530 I was able to do everything on my car scan it on test on it reset it it was only like a hundred seventy bucks best purchase ever made
How did you clean them????
Do you remmember size of socket T30, T40 ??? Thanks
I think I've mentioned in the video but if I remember correctly it was T40
@@WarpDriveM sorry, maybe I miss. I ordered 1 set of size up to T40 is maximum. Thanks
For the love of me i tried to get to the filters from the top and it is nearly impossible...dunno how you did it😊.
I got the rough idle on my E83 rite now and changed the plug and coils then the steering pump recently...thinking it’s still gonna give a rough idle when I go start it up thinking I need to clean or replace these filters along with the vanos and see if that is my problem as well these N52 motors are a big pain but when you get to changing parts you become familiar with everything in your vehicle good tips on the video thanks !! How long did the job take you to clean these 2 filters?
You should be able to do this job in 20 min....
I just noticed when I parked, put it in park my rpm dropped. Felt like it was going to shut off. May need to clean mine as well. What did you use to clean them?
Thank you! I have the same issue…
Hi! I got a E92 bmw 2007 , 2.5i 92.000 miles on the clock..The problemI got is the engine just cut of at lower speed. I changed the VANOS solenoids the oil filter and the oil, but nothing happend, engine cuts of at lawer speeds.Can you give me some advices please! , I see you know all about this tipe of engines.Thanks allot!!!
Usually when the power is cut at lower rpm is a vacuum leak, or fuel system error. At high rpm is always electric. Check the vacuum hoses from the engine cover to the intake, oil separator, maf sensor....
@@WarpDriveM i wiil do many thanks!!!!
I cleaned mine and car still idles badly and it has no check engine light
Hi mate I have very similar problem but my one is having code P0175 system too rich bank 2 any ideas please ? Thx.
You only have bank 2 if your engine is a "V" engine (v6/v8/...) system too rich can mean MAF sensor bad, bad injectors, fuel pressure too high, O2 sensor defect usually the first one before kat. This are just Infos, you need to let the car to be checked by someone who can give you a diagnosis...
I have the rough idle on my 2011 bmw 328i is the Veno locate in the same place like your car?
Letran I think so I’m going to try this because I have the same problem. Btw look at the video description is the ccv valve
Mine were not clogged but great video and well explained.
Excellent!
😎👍
Only clean solved the problem??