I kept mine 4x100 and running ITR calipers, mini Cooper 280mm rotor with 1320 spacers and z23 evolution carbon ceramic pads. Thought about throwing a crz rear solid axle, master and front bearings and spindles for 5 lug, 4 wheel disc upgrade, but I think I might just run the scare bird brackets ITR/ mini with crz master. For a little less anyway See you in the next one.
Its a known issue for 2nd gen fit, loose spark plugs throwing codes, believe there is a service notice to increase the torque from 11 or 12 ftlbs to something like 18 ft lbs.
I love them. Which one do you select ? I want to buy my honda fit too but I don't know which one you bought on the website. I'm new on this, so I'm kind of lost, lol.
I was kinda bummed when you put the TE's on and then didn't give a single shot of the car with the sun to your back, except for a few seconds of it turning around from a distance. Every other shot the "dark side" of the car being shown. I'm really considering a Fit as my next project (01 GC Subaru being my main I've had for 16yrs now (on TE's!))
Thanks. Went to the riaction website for my ge8 and 🥁 yup they dont carry coilovers for ge8's. Just 2015 & up. Bummer. Looking forward to ride quality though for reference .
GTI same problem, so I used the factory jack pt and put a jack stand on a metal frame point w/overlapping metal or one of front lca rear bolts. not a lift pt, just a stand pt.
torque to spec be damned.....if you knew that you were going to do this install, could you put penatrating spray on the fasteners in (pptential) problem areas 24-hours prior? it's not like this install was a surprise. I always have backup hardware just in case and usually replace the old stuff (if it had lots of miles) even if it came out clean. 🏁
Its not even tucking?? Is that all the drop you got?? At least the fender close to the top of the tire. Not looking good, if you like it that is all that matters.
I kept mine 4x100 and running ITR calipers, mini Cooper 280mm rotor with 1320 spacers and z23 evolution carbon ceramic pads. Thought about throwing a crz rear solid axle, master and front bearings and spindles for 5 lug, 4 wheel disc upgrade, but I think I might just run the scare bird brackets ITR/ mini with crz master. For a little less anyway See you in the next one.
I think you need to have a vote on wheel choices.
The coilovers made a bigass difference 👏🏼👏🏼👏🏼👏🏼👏🏼
That trick with the impact to crack the bolt was really smart!
Broo that fit be looking good and clean with those TEs.
A whole different car now! 🔥🔥🔥🔥🔥
Looking great. You have warmed my opinion of the 2g fit.
Your car looks very nice, I am happy vicariously.
That blue on blue looks incredible
soooo clear thank u. your videos are the best
Drilled slotted rotors and ceramic pads on a chair look good under those new wheels
Please share the link to the front lip you have installed
Its a known issue for 2nd gen fit, loose spark plugs throwing codes, believe there is a service notice to increase the torque from 11 or 12 ftlbs to something like 18 ft lbs.
I set mine to 20
I love them. Which one do you select ? I want to buy my honda fit too but I don't know which one you bought on the website. I'm new on this, so I'm kind of lost, lol.
The quality !!
It looks really good 👍 I would keep them if it where me... but to each their own. Looks clean slammed regardless
i put an intake in my fit am i a car guy yet
I was kinda bummed when you put the TE's on and then didn't give a single shot of the car with the sun to your back, except for a few seconds of it turning around from a distance. Every other shot the "dark side" of the car being shown. I'm really considering a Fit as my next project (01 GC Subaru being my main I've had for 16yrs now (on TE's!))
Looks good. What the wheel and tire spec
What diffuser is that? I notice they don’t have a lot of aftermarket parts for the ge8
Dammmmboiiii looking slick
@HondaStreetGarage WHICH TRANSMISSION (AT/MT) CAN BE USED FOR A SWAP ON AN EK, WITH A B20 ENGINE
Thanks. Went to the riaction website for my ge8 and 🥁 yup they dont carry coilovers for ge8's. Just 2015 & up. Bummer. Looking forward to ride quality though for reference .
They’re coming..
i
Came for EF content... ran away ! haha
Had a Fit before I got an Ef, the fit is honestly a dope car
I think he means more of the giveaway car
Whats the name and type of the bumper lip?
I'm interested in the front lip info as well
hi, can we use 215 tire on honda fit?
Yo mark i got a question if I were to jack up my DA to work under my engine where would I jack it up from? The oil pan or the transmission side?
GTI same problem, so I used the factory jack pt and put a jack stand on a metal frame point w/overlapping metal or one of front lca rear bolts. not a lift pt, just a stand pt.
Love the wheels, but I hate the blue on blue. That's just me, tho
That's purple? Oops I always thought mine was blue
Looks sick
torque to spec be damned.....if you knew that you were going to do this install, could you put penatrating spray on the fasteners in (pptential) problem areas 24-hours prior? it's not like this install was a surprise. I always have backup hardware just in case and usually replace the old stuff (if it had lots of miles) even if it came out clean. 🏁
Its not even tucking?? Is that all the drop you got?? At least the fender close to the top of the tire. Not looking good, if you like it that is all that matters.
💯💯💯
Great car and great vid
I like my Bc Racing Br series...on my Fit
Looks amazing!!
What size tire you using
very nice
Get it big dog
Miss the DA content 😢
Looks like a pregnant mr2
ahahah
🤣🤣🤣🤣
this build needs to be fast and different... or else its just sort of anti climatic and stale content imo
Man I used to really enjoy and look forward to these videos. Not anymore. There not as informational anymore. Not very eye catching.
Looking great!