The 89G - 🔧 FOX BODY Official Ford Procedure Base Idle Reset 🔧 - EP55
HTML-код
- Опубликовано: 12 авг 2021
- #EIGHTNINEGARAGE #FOXBODY #IDLERESET
Welcome to another episode of The Eight Nine Garage. In this episode, we do a base idle reset on Frankie the Fox Body. I use the Ford recommended method. Let's see if it works with the E303 and A3M combo.. Or, will I have to use alternative measures? Subscribe and ring that bell to stay current on all the haps with Frankie.
Buy the newer model of the Extech Multimeter that I used in this video:
amzn.to/3jJQD6u 
Авто/Мото
Did you have to swap the PCM?
Nope, it still has the A3M in it right now. This procedure got it to idle with that A3M computer.
Looks like you fixed it. Over 25 years straight of owning fox bodies, I've found the ignition module is often the culprit. They get really hot mounted on the dizzy. So much so, that on my 91 LX I've relocated it with a homemade heatsink. No problems since on this car.
It's been wonderful since I did this... I actually have an Sn95 heat sink I want to adapt for this at some point. Thanks for watching!
Yea that’s what I did with my 93 Ranger. Good idea.
I just wanted to say thank you for the video. I've been having problems with hot starts for a while and this cured it!
This is video explained it very well and easy to follow!
That's awesome! Thank you so much for jumping in and sharing your experience!
Look at that sparkly clean gauge cluster!!! 🤩😉👊
It looks so much better! I'm so glad you posted yours. It my interior look so clean.
Your starter turned over fast as hell. My starter sounds like the battery is damn near dead even with BRAND NEW battery. 🤷♂️🤷♂️🤷♂️😂😂
@ultraman33624 lol... my old starter was like that. Especially when it got hot! Thank you for watching!
@@89G I think it’s because I powder coated the timing chain cover and didn’t grind the powder off where it actually contacts the block around all the bolt holes so the starter isn’t properly grounded. It’s the only thing that actually makes sense since it does it with a brand new battery.
Great video and your instructions were crystal clear.
@@ultraman33624 Oh, OK! Gotcha....
This is the best explanation ive seen of this yet. Done the procedure a few times now but always come back for a refresh! Thanks! Works with the X3Z PCM I have!
Thank you for your kind words! I am happy I was able to help you out.
I think the trick is getting it set on the base idle 725 or lower. We all contribute the stalling to low idle so we try to set it higher to compensate but the computer will shut out the control if it cant control the idle low enough to learn the bottom drop of the idle witch causes the stall. Im going to test this theory tomorrow ive got a 92 doing the exact same thing heck even the a/c will stall it at idle. Thanks for the vid it helped a lot.
You're very welcome! My E303 likes 700. I'd love to get it a bit lower though.
@@89G Thats the same cam Ive got in this car.
@scottsinfl I have a Trick Flow stage 2 that I may put it. I've seen a lot of people complain about idle issues with the E303. I also have a Comp Cams 274HR as well... but it's in a 351 on my engine stand.
Saved this 1 for sure. * Thank U *
A stock A9L computer is set to 672rpm's for a manual and 672 idle and 624 in drive with an automatic so setting your idle at 50rpm's your IAC wont even be used for maintaining idle.....It will be all throttle blade or Tom Brady screw as you call it...
The way I set the idle is I set my idle to 600 rpm's which gives 72 rpm's of idle drop for the IAC to cover and for the adaptives to learn alot quicker.......If you set the idle to where it barely idles then the idle will swing that low...................
Another thing about setting the idle at 600 if you have a manual and you granny shift the idle wont drop much below 600.............
Instead of twisting the distributor to advance timing and gain power I make myself an octane rod thats is tad shorter than the rod that sets and locks the halls effect trigger in place...........I usually go with one thats roughly 2 degrees advanced..
by far best one I seen on youtube. easy to understand you.
I sincerely appreciate your support 🙏
Aw man, this right here is the best idle reset video on youtube! Glade you mentioned your channel on junkyard doggs most recent video. Subbed 🤙🏼 keep em coming!! (:
Thank you very much for the kind words, support, and sub! I love Junkyard Doggs channel... I hope he keeps it going!
I agree Bro!
Subbed!! Glad it worked. I will definitely reference this vid next time I have to do mine on my 91 LX Vert. Thx
Thank you for your support and the sub!
Great video .I have 86 GT i bought new in april 86 .have set tps many times over the years.doing idle reset has her idling awesome.
Thank you so much for your feedback! This method has worked for me many times!
Thank you very much, you are a Master, grettings from Lima- Perú
You're very welcome! I appreciate your support and feedback 🙏
Wow that was an awesome video! Very clear and easy to follow. Nice job man!
I really appreciate it 🙏 thank you so much!
oh good. ima use this on mine too ty 4 this
I hope it helps!
I've seen where if you are having trouble in this area but with a surging idle and getting egr codes, you can change out the coolant temperature sensor and it will clear it up.
Good to know, I was not aware of that trick. I appreciate you adding that to the comments!!
I have an issue with cold starts. It rough idles for about 3 minutes and then it clears up. I have changed the coolant sensor and purchased the pcv kit and air charge temp sensor but haven’t taken it to the mechanic. I will definitely try this after replacing the act, pcv kit, and a new c&l 76mm maf. 😊
Let us know how it goes!
Ill try this tonight. When the engine is cold it start and stall immediately. Try again and itll try to die.
I hope it works for you! Please let us know... I'll try to help in any way I can.
Ok so I did this method and it seems so far to have worked. So thanks for sharing
@@trailerpark187 That is fantastic! I'm so happy it helped you out
Dude bad ass video I’m going for it only thing is my idle is fast not slow. I think we need a video on vacuum test 😕
I have one on smoke testing for vacuum leaks. I'll get you a link.
Here you go. IMO, this is the best way to check for vacuum leaks. Let me know if you have any questions or suggestions. ruclips.net/video/vsOO36yaj90/видео.html
Dude when I unplug at beginning that shit it idle perfect ??????
@@bryanrobinson7969 do you mean the MAF sensor?
No iMac u call it step 2
Wow! Where did you find this? Like clam Ford? Everyone I have ever seen you disconnect battery first I wonder if it changes anything
I am SO sorry! RUclips didn't tell me that they had held your comment for review. This was published in one of the Motorsport publications years ago. This method has always worked very well for me.
I’m going to do this on my car tomorrow hopefully it the weather holds up. Especially since I just got it running again
I'm glad you got it going again! Hope to see you at some shows this year! Hit me up if you have questions.
@@89G thanks man! I hope to be at quite a few shows
@@alexchadbourne Nice. The Fox Body turnout has been pretty decent lately.
@@89G so I’ve seen
@@alexchadbourne maybe we can get yours in a video or two. I wonder how it would do with some paint correction?
I got to ride in Frankie!lol
I hope you liked it! Did you get your Toyota yet?
Not yet. I wanted made well so I put an order in to Japan. I know some Toyota’s are made in Mexico and I’ve heard horror stories. Where was your Yaris made?
@@gregdiiamond3899 it still has the "Made in Japan" sticker on the drivers door window.
I want to adjust my tps and my timing. But I can’t start these steps until my misfiring situation is figured out. I don’t want to get my 302 to operating temps while it’s misfiring
Sorry... YT just barely sent me this notification. Is your firing order correct? What year is your 302?
Do you have your fuel line going to vacuum tree or the intake itself... trying to see if I did something wrong... I deleted the egr & all the smog & tad/tab sencors...
I will go look in the morning. I don't remember where I tapped in. I do know that it needs to be a direct connection though - not ran the the TAD and TAB.
Having this exact issue with my 91….except I have 24lb injectors BUT…I don’t think my maf is the issue could be unsure going to try this reset see what happens before I order a $250 maf sensor
This procedure works very well. Do you have a 24 lb MAF?
@@89G I don’t. Which is why I think I’m having the issue
Is it still the stock piece?
@@89G stock piece?
@@joekloiber887 Joe, I need to apologize. YT never sent me the notification that you had responded. I was meaning do you still have the stock MAF? I put the C&L on my 89 with a matching 24 lb. calibration tube.
Do you adjust timing before or after?
I adjust it first, then recheck. Sometimes all you can do is get it close when it wants to die.
When do you set the timing on the motor? Before all of this or after?
Great question! I set it beforehand on this car However, if it won't run long enough to set it, I just get it close, then recheck after.
Do you have to reset the timing of the car just idles higher than normal
@@89G I changed my spark plugs cap and rotor spark plug wires and now my stang idles higher than normal
Does this idle reset work with speed density?
Yes, it should as long as you don't have vacuum leaks.
Are you in Colorado
I'm next door in Utah.
Dood video I did new pcv kit cleaned throttle body sparks and wires. Idle now is all ver the place.
Thank you! What year is yours?
@@89G 88 foxvert manual
@@alvaropimentel779 do you have speed density or mass air?
@@89G good question I just bought it 3 weeks ago I’m not sure how do I find out?
@@alvaropimentel779 In the intake tube, between the throttle body and the air cleaner, you will have a sensor with 4 wires if you have mass air. If you don't have a sensor, it's speed density. Most 88's did not come with it. Only California Emissions equipped cars had it. Let me know if you need anymore help. The mass air cars are a lot easier to play with overall.