Update: after resetting TV, lower backlight brightness to 50% in tv menu then do firmware update via internet or USB drive to prevent future errors. if error happens again and again you must replace LED backlight strips, see that fix here- ruclips.net/video/YgaL6X6eSaU/видео.html #sharpTVrepair #sharptvfix #sharptvreset #howtofixSharptv
Great information, should help lots of people! Need some help with a un65f9000 tv, screen mostly bright white with green / blue at bottom & top. Have already replaced tcon board and power supply voltages look good. Suspect main board component but cannot figure it out, any help appreciated. Thanks
Tampatec I need help with my 70" sharp aquos. Cant do anything anymore as far as any resets. I did one and it went back to frozen screen and cant do any changes
Hi. Thank you for your informative videos. I also have a screen problem with a 32inch Sharp LCD TV and was hoping that you would be able to point me in the right direction to find the solution. Every time we turn the TV on the image goes out after about a second, but sound remains. There is a bit of flicker before the screen turns black. To get the screen to stay on we have to repeatedly switch it to standby mode and back on again. Sometimes it takes three attempts and other times up to ten. Do you perhaps have an idea where the problem could be? Thanking you in advance, Klaus Oellrich
My TV quit right during the Super Bowl. I immediately went to You Tube to find a solution as there was no way I could get a tech to come out. This worked for me. I couldn't believe it! I have never fixed anything electronic in my life. Thank you so much for posting such clear instructions. My husband is impressed.
this is jeff and i wanted to say thank you. your suggestion worked great and everyone is happy. you saved me a new tv. much appreciated. Merry christmas.
I recently switched cable carriers: from Direct TV back to U-verse (which was not without significant heartburn, it took 3 techs to complete the switch). Suddenly the picture on my 52" Sharp plasma TV began flickering and went out! The U-verse tech said my TV has gone bad. I was beside myself and refused to believe it. So, I googled the problem and watched the RUclips video on how to reset the TV. IT WORKED PERFECTLY!!!! I am again watching my beautiful TV with a crystal clear picture!!! THANKS SO MUCH Tampatec. I will always search for your advice before the repairman!!!
Another happy customer! For my model it was hold volume down and TV/VIDEO for LC-22LE520X-BK then the LED light turns orange and channel up and down brought it to life and it is now reset.
I had to do this three times but on the third attempt it worked perfectly. Not sure why it did not work the first couple of times and i am sure I followed the directions to the detail but when I got to the green screen and shut it off, I then unplugged and replugged and the arrow light flashed the first two times. Third time a charm. Thanks for the tip, you saved me a lot of money.
Hi , I own a TV repair company, Affordable Mobile TV Repair in Virginia Beach Va. The reason that I responding to your post is that you are telling half of the story. These sets accumulate lamp error codes, so just zeroing them out of the register and resetting the set will NOT permanently fix the set. It's a temporary fix at best. We have repaired approx 250 of these sets over the last 3 years and most of the time, you have to replace the led strips themselves to ensure a permanent fix for this problem. If you do not, the tv will show the same blink code again after the register accumulates more than 6 lamp error hits! Thanks
Wayne Mitnick thanks, for the tips, I did a few LED strips before but thought this error was triggered by a software glitch because tv came on and stayed on. I thought maybe there could be a firmware update to patch it. Awesome you're helping the community, if you start a RUclips channel I'll sub. I respect your professional advice. i added that note in the video description, Thanks again
So I have this issue and once I followed the lampreset I ALSO hooked TV into a battery backup. That way if power goes out for a few minutes, the TV wont start the flashing as long as there is continuos power via outlet or ups. Working for over a year no rese needed a 30 UPS keeps it powered for a bit
288 people were frustrated because they didn't had the exact same tv.... Tampatec is an AWSOME chanel ! My tv ain't the same as this very model but it still gave me the will to repair that broken tv that I have. Thanks !
Yo thanks very much , I HAVE THE SHARP 40LE that after 8 years was having almost the same problem , the power lead light was flashing green and did not want to turn on ...YOU SAVED ME A COUPLE OF HUNDRED OF DOLLARS CAUSE I WAS GOING TO SEARS TO BUY A NEW ONE
Thank u it work u were the only person i seen on here that got down to it. Other did way to much unnecessary talking. U rock again thank u for sharing this with us.
First of all, thank you for your videos. They’re easy to follow and I appreciate your time. I tried all of you fix options, but none have worked. I have had this 55” Sharp TV model LC55P8000U for LESS THAN 8 months and it already stopped working. When I try to turn it on with the remote the red power light stays on but nothing happens. If I press power again, it blinks 5 times and then turns off. To make things even more confusing, sometimes when I press the power button from the remote there is a 3-4 second delay and then the red light blinks 5 times. And AGAIN, sometimes it’ll blink 10 times. I’m so confused. I keep reading about trying the reset where you hold down the volume and input buttons, but my tv DOESN’T HAVE BUTTONS!! It only has one joystick thing that has engraved arrows for up, down, left, right, and the center button says ‘ok’. I tried that process with my remote buttons... still nothing. Any chance you can help?
Unfortunately it did not fix my problem, I suspected power module issue from the beginning but I want to commend you on your content, your ability to put "tech savvy" information into Simplified Technical English is very polished. The information you provided at the end was a great closeout for those of us who need to delve into the more complicated fix (not so complicated but not a simple button hold combination either). Thank you for putting this information out there, you have my like and sub.
Awesome you saved the day!!! We don’t have the normal TV remote and could not hit the select button to confirm it was ok or on but when we turned it off and on for the third try it worked . Yay thanks so much . Your awesome .
** Unfortunately this fix did not work for me. I called a tech out for $59 and the fix was to hold the Volume +, Volume -, and Power button at the same time and then plug the TV back in and wait for the solid light to come on. This will work until there is a power outage or the TV is unplugged, then the slow followed by the quick blinking light will go on again. Hope this will help some folks out that couldn't make Tampa Tec's original fix work. **
You're a life saver. Sharp TV's used to be good - junk now. Like a Hitachi I used to have. Had to replace a board on the Hitachi after only having it 2 weeks.
John Copeland Just trying to help; the Owner's Manuals will sometimes tell you that it's best to unplug devices such as TVs and computers during severe weather for this exact reason. Other than that, make sure that your TV is plugged into a surge protected outlet or power strip.
Hi Tampa Tec, I tried to reset my Sharp equos LC-52LE640 by holding down the volume and the input buttons, then plugging in the power. It shows me a quick dim flash but there is not picture. Also the Light under the Sharp logo gives me a long flash and then a shot flash, it looks very dim. Do you think it might be a bad power supply? Thanks!
Dude. The hassle that you have saved me is incredible. First let me start by saying my tv is the 80 inch version of the tv you are demonstrating on. With a few minor exceptions, page 2 of 26 and holding the power button while the tv is turning back on, everything else worked as you illustrated . BIG THANK YOU
Hi nick, I have the same model. but when I tried to vol-&input I see img for 1 second.. I remove the power cable from the tv not from wall because its hidden (on office) its relevant?
Channel up and down or volume up and down is sometime used to navigation in settings, and input or source button sometimes used for select. Some TVs have a short or flush joystick near it sensor on the TV back or bezel, and if u push in it may select or turn TV on off.
Thanks for the video. It worked for me once, and I enjoyed a night of tv. Today it started the blinking again. So I tried the trick again, and the tv showed the solid light, as if it’s trying to power on to get to the K message. The tv turns on for a split second and then turn off and goes right back to blinking. Any advice, or maybe you can tell me what I may need to try and fix this myself. Thank you.
I have a 40", pretty sure it's a standard LCD predating LED from 2011. This got the TV on, but it does appear to have a legitimate backlight issue as it constantly flickers in brightness. The first thought is a backlight inverter board, though I've seen all kinds of issues caused by the main power supply itself. Do you happen to have any advice on testing for faults in the inverter board?
This worked thank god. Appreciate it man.and mine was a sharp plasma i think from 10 yrs ago. Gonna toss this 1 out and get a new one soon,but this video def helped as i was getting rdy to toss this thing out
Hi @TampaTec, I have same model sharp 80in in our office. I tried the method you have show on the video but I did see image for 1 second (I unplugged all hdmi and external cable) the different thing I did its unplug the power cable from the tv and not from the wall because its hidden inside the wall. you think its relevant?
Thanks for this have just tried this technique. I have a blinking blue light every secondand i am having difficulty to get it steady with lamps very faint on rhe screen. Any tips thank you
TampaTec I reset my sharp Lc 70le734u Everything works fine. But when I remove power from the wall outlet I have to reset tv again. Which board do I need to change There is a Led control board , main control board and a t-con board also power supply board. Can you tell me which one I need Thanks so much Keep up the good work you do on you tube Vic
So after trial and error I got the TV to turn on.I had the menu on and was about to select the reset stuff but Whilst trying to look for the remote..clumsy me tripped over the cord and the TV unplugged!!!! OH NOOOOOO !!! But as soon as I plugged it in..my TV was back to normal 👍💃🏾 Now my mom can resume her regular programming of Little House On The Prairie and Gunsmoke reruns (on DVR) THANKS 😊 👍
Good afternoon ! My TV is sharp LC 5277UN .power led and OPC indicators are blinking simultaneously. And I tried ur experiment on it but didn't come up .why is the opc indicator blinking along with the power led ? More hints pls.Thanks.
Might be bad main board, but first check standby volts on Power board to be sure your power board is ok. Get TV boards at shopjimmy.com or electropartsonline.com
Greetings, with your info to reset I at least managed the LED turn green from red. It is an Aquos LC-37HV4E. Older than the o you show. But the Menu looks completely different and has less choices. Woud you please help me if you have some insider information how to reset the Aquos LC-37HV4E?
My Sharp (LC46E77UN) blinks a steady pattern. I tried all the reset options, to no avail. So black screen, blinking in stand-by mode. Sometimes when I plug it in and press power it'll will power up for a few seconds , with same black screen then power down and start blinking again. Any suggestions. ? I might be posting this to the wrong link , my apologies , new to this.
I have a Sharp Aquos LC-60LE831U. All HDMI inputs fail but I can still watch DVD movies and Netflix using an ethernet cable. I replaced the main board and got the same long/short blinking sequence but I am having trouble powering up after watching your video for the 70" TV. Is there something different I have to do for the 60" model? Thanks
I have a Sharp LC-60LE835U doing the short flash long flash thing, but it does not respond to the reset/restart sequence described here. This model has "soft" buttons on the face of the TV. Does this make a difference? Do I need to so something else?
Have you ever troubleshot a sharp tv model LC-40LE810UN that does not turn on. The standby light doesn't come on either, it acts like it has no power and the outlet it is plugged into is good. I have a multimeter, I just want to know how to troubleshot the power supply to make sure that is the problem or if there is any other tips you might have.
I have the same problem. I can't find my particular TV but I do have a sharp LC-37SH20U. The buttons are top, and the shelf above blocks access. Would the steps be the same as yours?
Thank you very much for the great video. It worked on my LC70LX732H fit the first time. However, after the factory reset, it did not come up and the light kept blinking. Then I tried to repeat the step - “plugging in the power while pressing Vol Down and Input”... then screen does not turn on again! Anything else I can try?
I have a huge question could you possibly give me some advise?! So I followed the video and when the settings are suppose to pop up mine does not however the white light stays on and solid any chance you could steer me in the right direction?!? Please!
I have a 60” SHARP AQUOS Model# LC-60E77UN that started having this power blinking light issue. I followed your video but the TV still doesn’t turn on and the light keeps blinking. The TV is 11 years old. What is your recommendation? Is it worth fixing?
Is there anything you can do for one vertical line going down it's yellow. The bottom kind of fluctuates. The last three or four inches from the bottom.
Why, I did reset follow the intrustions ( reset Lamp Error Reset, moved Reset to ON, and “Industry INIT to ON) but TV not turn ON and Led continue flashing? Please help me , Thanks!
Hello I have a 90” sharp and it is doing the same thing but it does not bring up the serial number on the screen like that and the Chanel down and volume down still does not work. Would this be the LED strips? I already replaced the main board.
How do you get into Service Mode of a Sharp Aquos TV Model :LC-80LE632U using the Remote ? Pressing CH - & INPUT while plugging in the TV is not working.Thanks for your tips.
I have a LG 6550 tv that was bought last year. Last week the lower 3rd of the screen begin blinking greyish lines. I unplugged the tv and plugged it back in. I also unplugged the cable box to the tv but it even did the grey lines blinking/flashing with the items disconnected. The only thing that has ever been connected to the tv has been the cable box. Do you propose the next step is going in and reset to original settings? Or is it an internal issue?
I am trying to fix a sharp tv for my friend I confirmed a bad led strip and replaced with parts from shop jimmy I get red flashing light it wont turn on with remote when I push the power button on tv now I get backlight but no input or logo symbol I tried this method is that a mainboard issue I will check voltage from power supply next but figured power supply is good since it turned on when pushing power button on tv thanks for all the great videos I bought led tester you recommended from shop jimmy worked great any advice would be great
I have an issue with my Sharp Aquos LC-52LE810UN. The front panel volume buttons trigger on their own, raising and lowering the volume. I determined this by disabling the front panel buttons, but that just results in a popup in the center saying "the operation is not allowed". Is there a way through the service menu or otherwise I can physically disable the front panel buttons? Thanks.
![Digital Circus Episode 4 [TRAILER]](http://i.ytimg.com/vi/abZtsmMUbJo/mqdefault.jpg)
Update: after resetting TV, lower backlight brightness to 50% in tv menu then do firmware update via internet or USB drive to prevent future errors. if error happens again and again you must replace LED backlight strips, see that fix here- ruclips.net/video/YgaL6X6eSaU/видео.html
#sharpTVrepair #sharptvfix #sharptvreset #howtofixSharptv
Hi Tampatec. Will you be doing another home theater unboxing/review ?
Tampatec bro do u know when wireless earbuds need chargeing or are dead
Great information, should help lots of people! Need some help with a un65f9000 tv, screen mostly bright white with green / blue at bottom & top. Have already replaced tcon board and power supply voltages look good. Suspect main board component but cannot figure it out, any help appreciated. Thanks
Tampatec I need help with my 70" sharp aquos. Cant do anything anymore as far as any resets. I did one and it went back to frozen screen and cant do any changes
Hi. Thank you for your informative videos. I also have a screen problem with a 32inch Sharp LCD TV and was hoping that you would be able to point me in the right direction to find the solution. Every time we turn the TV on the image goes out after about a second, but sound remains. There is a bit of flicker before the screen turns black. To get the screen to stay on we have to repeatedly switch it to standby mode and back on again. Sometimes it takes three attempts and other times up to ten. Do you perhaps have an idea where the problem could be? Thanking you in advance, Klaus Oellrich
My TV quit right during the Super Bowl. I immediately went to You Tube to find a solution as there was no way I could get a tech to come out. This worked for me. I couldn't believe it! I have never fixed anything electronic in my life. Thank you so much for posting such clear instructions. My husband is impressed.
Wendy Logan awesome I hoped this video saved super bowl Sunday in time 👍
Thankyou bro 👍👍
Dude I went from crying in my beer to jumping up and down for joy. Fixed on 1st try. Thanks for this video!
this is jeff and i wanted to say thank you. your suggestion worked great and everyone is happy. you saved me a new tv. much appreciated. Merry christmas.
I recently switched cable carriers: from Direct TV back to U-verse (which was not without significant heartburn, it took 3 techs to complete the switch). Suddenly the picture on my 52" Sharp plasma TV began flickering and went out! The U-verse tech said my TV has gone bad. I was beside myself and refused to believe it. So, I googled the problem and watched the RUclips video on how to reset the TV. IT WORKED PERFECTLY!!!! I am again watching my beautiful TV with a crystal clear picture!!! THANKS SO MUCH Tampatec. I will always search for your advice before the repairman!!!
You deserve a raise! Been searching for a way to fix this tv for a week. Service guy said it was the plug. Which we couldn't find anywhere. Thank you!
Another happy customer! For my model it was hold volume down and TV/VIDEO for LC-22LE520X-BK then the LED light turns orange and channel up and down brought it to life and it is now reset.
Even though I have the 46" Model which doesn't have Buttons to Push in, I appreciate watching your video. Very helpful for others I'm sure. Thanks.
It worked! It worked!!! You saved me $3,000 because I didn't want to have to replace a 7 year old tv! Thank you soooo much!
I had to do this three times but on the third attempt it worked perfectly. Not sure why it did not work the first couple of times and i am sure I followed the directions to the detail but when I got to the green screen and shut it off, I then unplugged and replugged and the arrow light flashed the first two times. Third time a charm. Thanks for the tip, you saved me a lot of money.
Thank you kind sir!! I have a older 60” Sharp Aqous and I couldn’t for the life of me figure it out! Your video fixed it! Genius!
I have a 70 inch and just fixed it. Thought I was going to have to throw it out
Hi , I own a TV repair company, Affordable Mobile TV Repair in Virginia Beach Va. The reason that I responding to your post is that you are telling half of the story. These sets accumulate lamp error codes, so just zeroing them out of the register and resetting the set will NOT permanently fix the set. It's a temporary fix at best. We have repaired approx 250 of these sets over the last 3 years and most of the time, you have to replace the led strips themselves to ensure a permanent fix for this problem. If you do not, the tv will show the same blink code again after the register accumulates more than 6 lamp error hits! Thanks
Wayne Mitnick thanks, for the tips, I did a few LED strips before but thought this error was triggered by a software glitch because tv came on and stayed on. I thought maybe there could be a firmware update to patch it. Awesome you're helping the community, if you start a RUclips channel I'll sub. I respect your professional advice. i added that note in the video description, Thanks again
so does this mean that this temporary fix will only work 6 times?
Wayne Mitnick. The tv will not show a picture alls it does is blink
My tv does not have a picture thats all it does is blink
So I have this issue and once I followed the lampreset I ALSO hooked TV into a battery backup. That way if power goes out for a few minutes, the TV wont start the flashing as long as there is continuos power via outlet or ups. Working for over a year no rese needed a 30 UPS keeps it powered for a bit
Legend! Thanks Bro. It was the TV flashing green light, tried the vol+input for 20sec and that fixed the issue.
@@josephginu congrats 🎉
Thank you. I had to initially leave my tv unplugged for about 30 minutes before I could successfully complete this process.
Thank you for this. I will try this tonight! I've had mine in the garage for over a year.
Just fixed a 60” aquos I just got for free on Craigslist today..This is the second tv I’ve fixed with your advice...Thanks a lot!
This video is fantastic and was a game changer for me so thank you very much from Maui Hawaii. I owe you many pina coladas.
Awesome, yeah those drinks are my favorite.🍹
288 people were frustrated because they didn't had the exact same tv....
Tampatec is an AWSOME chanel !
My tv ain't the same as this very model but it still gave me the will to repair that broken tv that I have.
Thanks !
Yo thanks very much , I HAVE THE SHARP 40LE that after 8 years was having almost the same problem , the power lead light was flashing green and did not want to turn on ...YOU SAVED ME A COUPLE OF HUNDRED OF DOLLARS CAUSE I WAS GOING TO SEARS TO BUY A NEW ONE
D Santos update after 5 times doing the same thing tv won’t turn on no more 🤭😭😭😭time to buy a new one
Thank u it work u were the only person i seen on here that got down to it. Other did way to much unnecessary talking. U rock again thank u for sharing this with us.
Thanks
I think this literally saved my life, disabled, no money - I was that depressed.
same position as me being disabled, money and depression I think I am overcoming
@@robvandermeid7222 Nice to know I'm not alone.
First of all, thank you for your videos. They’re easy to follow and I appreciate your time. I tried all of you fix options, but none have worked. I have had this 55” Sharp TV model LC55P8000U for LESS THAN 8 months and it already stopped working. When I try to turn it on with the remote the red power light stays on but nothing happens. If I press power again, it blinks 5 times and then turns off. To make things even more confusing, sometimes when I press the power button from the remote there is a 3-4 second delay and then the red light blinks 5 times. And AGAIN, sometimes it’ll blink 10 times. I’m so confused. I keep reading about trying the reset where you hold down the volume and input buttons, but my tv DOESN’T HAVE BUTTONS!! It only has one joystick thing that has engraved arrows for up, down, left, right, and the center button says ‘ok’. I tried that process with my remote buttons... still nothing. Any chance you can help?
Thank you! It was really helpful. I could fix the TV which I thought is broken 😮 I inherited it from previous tenant. Great video!
Unfortunately it did not fix my problem, I suspected power module issue from the beginning but I want to commend you on your content, your ability to put "tech savvy" information into Simplified Technical English is very polished. The information you provided at the end was a great closeout for those of us who need to delve into the more complicated fix (not so complicated but not a simple button hold combination either). Thank you for putting this information out there, you have my like and sub.
Got a 70" this worked!!!! Thanks so much all I need is a TV stand now!!
Awesome you saved the day!!! We don’t have the normal TV remote and could not hit the select button to confirm it was ok or on but when we turned it off and on for the third try it worked . Yay thanks so much . Your awesome .
I was about to return this 70 inch Aquos Sharp until I watched your chanel,TGANK YOU MY TV WORKED FINE FINALLLLLLLY TGANKS TO YOU.
Thanks so much. Tv is more then 12 years old. Saved me hundreds $$$
Great video, very helpful. However after doing the resets, unplug TV, HOLD THE POWER BUTTON DOWN while plugging the TV back in
SAVED MY LIFE THANK YOU
You just saved my T.V. thank you so much!
I can’t thank you enough! It worked perfectly!! Your the best!!!
I have issues with my sharp. After loading, not responding to remote.
Worked perfectly the first time! Thanks!
** Unfortunately this fix did not work for me. I called a tech out for $59 and the fix was to hold the Volume +, Volume -, and Power button at the same time and then plug the TV back in and wait for the solid light to come on. This will work until there is a power outage or the TV is unplugged, then the slow followed by the quick blinking light will go on again. Hope this will help some folks out that couldn't make Tampa Tec's original fix work. **
Thank you this is very helpful
Thanks this worked for me!
Thank you Mike. Nothing work until I tried volume+ and volume - and the per button.
Thank you, this has worked for me
Do I unplug the power cable then click volume+volume- and power button?
You're a life saver. Sharp TV's used to be good - junk now. Like a Hitachi I used to have. Had to replace a board on the Hitachi after only having it 2 weeks.
i think many tvs have their common flaws but if i can fix it I'm happy. Plasma TVs and DLP i try to avoid.
Hello, Could i have a contact number? I am from Guyana and lighten frequently damage our television here.
John Copeland Just trying to help; the Owner's Manuals will sometimes tell you that it's best to unplug devices such as TVs and computers during severe weather for this exact reason. Other than that, make sure that your TV is plugged into a surge protected outlet or power strip.
Mine is a 32” and this tip worked for me, as soon as I did the first step, the TV came on. Thanks for the help. 👍🏼👍🏼👍🏼
It worked! TV is back on👍 Many Thanks!
Hey, be careful when handling that T.V. bro. It's Sharp.
SHARP IS THE BEST TV THERE IS , WONT BUY A TV SET IF IT IS NOT SHARP
lol
overthemountain90 oOf
😂😂😂😭😭😂😭 You might get cut 😐
Toooooop
Tampatec I have a Sharp Aqos LC-60LE600U that while I was watching tv it turned off and won't turn back on. Any thoughts???
This worked on my Sharp LC-46SB54U. The Green flashing Power Button. Only flashing constantly. My shop but nice to have. Thank You.
Man just want to say thank you, very clear instructions,
Man you are the best on RUclips your video are really great 👍 and helpful thank you very much all the best
kanchour16 thanks 😁
Hi Tampa Tec, I tried to reset my Sharp equos LC-52LE640 by holding down the volume and the input buttons, then plugging in the power. It shows me a quick dim flash but there is not picture. Also the Light under the Sharp logo gives me a long flash and then a shot flash, it looks very dim. Do you think it might be a bad power supply? Thanks!
Dude. The hassle that you have saved me is incredible. First let me start by saying my tv is the 80 inch version of the tv you are demonstrating on. With a few minor exceptions, page 2 of 26 and holding the power button while the tv is turning back on, everything else worked as you illustrated . BIG THANK YOU
Hi Nick. You are saying instead press the -Vol and Input only press the Power button and that's all?
Hi nick, I have the same model. but when I tried to vol-&input I see img for 1 second.. I remove the power cable from the tv not from wall because its hidden (on office) its relevant?
What if you don’t have a remote to select OK for the reset? Is there a button on the side of the TV to press?
Channel up and down or volume up and down is sometime used to navigation in settings, and input or source button sometimes used for select. Some TVs have a short or flush joystick near it sensor on the TV back or bezel, and if u push in it may select or turn TV on off.
This guy right here..is a life saver
This worked on my LC-32GPU1, Thank you so much friend!
At the last step be sure to hold down power when plugging back in
Thanks for the video. It worked for me once, and I enjoyed a night of tv. Today it started the blinking again.
So I tried the trick again, and the tv showed the solid light, as if it’s trying to power on to get to the K message. The tv turns on for a split second and then turn off and goes right back to blinking.
Any advice, or maybe you can tell me what I may need to try and fix this myself.
Thank you.
Change the display settings from standard to dynamic or custom and change the backlight / brightness
@@joshslim3 How do you do that if the tv turns back off after 1 second?
I have a 40", pretty sure it's a standard LCD predating LED from 2011. This got the TV on, but it does appear to have a legitimate backlight issue as it constantly flickers in brightness. The first thought is a backlight inverter board, though I've seen all kinds of issues caused by the main power supply itself. Do you happen to have any advice on testing for faults in the inverter board?
This worked thank god. Appreciate it man.and mine was a sharp plasma i think from 10 yrs ago. Gonna toss this 1 out and get a new one soon,but this video def helped as i was getting rdy to toss this thing out
Thank you so much, finally to fix my nightmare
Worked for me!!! Thank you so much!!!!
Thank you. My old but effective aquos 40’ still work with your video.
Hi @TampaTec, I have same model sharp 80in in our office.
I tried the method you have show on the video but I did see image for 1 second (I unplugged all hdmi and external cable)
the different thing I did its unplug the power cable from the tv and not from the wall because its hidden inside the wall. you think its relevant?
Thanks alot. It works. Have a nice day. Gbu always 👍
Omg actually worked liked and subbed bro
Thank you this worked for us 😀
You are a Genius
Thanks for this have just tried this technique. I have a blinking blue light every secondand i am having difficulty to get it steady with lamps very faint on rhe screen. Any tips thank you
Great bro. Thank you for the info.
Tampa Tec Rocks! 👍🏼 👍🏼 👍🏼
TampaTec I reset my sharp Lc 70le734u Everything works fine. But when I remove power from the wall outlet I have to reset tv again. Which board do I need to change There is a Led control board , main control board and a t-con board also power supply board. Can you tell me which one I need Thanks so much Keep up the good work you do on you tube Vic
I LOVE YOU! THANKS ❤❤❤❤
You are the Best .
Thanks this was a BIG help got my TV working again
Good solution, any idea why this does this?
So after trial and error I got the TV to turn on.I had the menu on and was about to select the reset stuff but Whilst trying to look for the remote..clumsy me tripped over the cord and the TV unplugged!!!! OH NOOOOOO !!! But as soon as I plugged it in..my TV was back to normal 👍💃🏾
Now my mom can resume her regular programming of Little House On The Prairie and Gunsmoke reruns (on DVR) THANKS 😊 👍
Good afternoon ! My TV is sharp LC 5277UN .power led and OPC indicators are blinking simultaneously. And I tried ur experiment on it but didn't come up .why is the opc indicator blinking along with the power led ? More hints pls.Thanks.
Might be bad main board, but first check standby volts on Power board to be sure your power board is ok. Get TV boards at shopjimmy.com or electropartsonline.com
if i could like several times i would man thank you so much
Thank you very much, it worked🎉
It's works for me!!! Thank you so much so much Bro!!! 😁😁😁👍👍👍
Greetings, with your info to reset I at least managed the LED turn green from red. It is an Aquos LC-37HV4E. Older than the o you show. But the Menu looks completely different and has less choices. Woud you please help me if you have some insider information how to reset the Aquos LC-37HV4E?
Do you get a solution?
My Sharp (LC46E77UN) blinks a steady pattern. I tried all the reset options, to no avail.
So black screen, blinking in stand-by mode. Sometimes when I plug it in and press power it'll will power up for a few seconds , with same black screen then power down and start blinking again. Any suggestions. ?
I might be posting this to the wrong link , my apologies , new to this.
You're a Genius. Unbelievable. That works perfectly! 👏🙌👏🙌
Thank you. I fixed it with your help
Congrats fixing your TV.
I have a Sharp Aquos LC-60LE831U. All HDMI inputs fail but I can still watch DVD movies and Netflix using an ethernet cable. I replaced the main board and got the same long/short blinking sequence but I am having trouble powering up after watching your video for the 70" TV. Is there something different I have to do for the 60" model? Thanks
I have a Sharp LC-60LE835U doing the short flash long flash thing, but it does not respond to the reset/restart sequence described here. This model has "soft" buttons on the face of the TV. Does this make a difference? Do I need to so something else?
I press the Function button and the Source button and it was ok for me !!!
Have you ever troubleshot a sharp tv model LC-40LE810UN that does not turn on. The standby light doesn't come on either, it acts like it has no power and the outlet it is plugged into is good. I have a multimeter, I just want to know how to troubleshot the power supply to make sure that is the problem or if there is any other tips you might have.
This worked! Thank you so much man
You are my HERO! This worked!!!
I have the same problem. I can't find my particular TV but I do have a sharp LC-37SH20U. The buttons are top, and the shelf above blocks access. Would the steps be the same as yours?
Thank you very much for the great video. It worked on my LC70LX732H fit the first time. However, after the factory reset, it did not come up and the light kept blinking. Then I tried to repeat the step - “plugging in the power while pressing Vol Down and Input”... then screen does not turn on again! Anything else I can try?
I have a huge question could you possibly give me some advise?! So I followed the video and when the settings are suppose to pop up mine does not however the white light stays on and solid any chance you could steer me in the right direction?!? Please!
2024 and it still works! Thanks
thanks bro , you ve been of great help
I have a 60” SHARP AQUOS Model# LC-60E77UN that started having this power blinking light issue. I followed your video but the TV still doesn’t turn on and the light keeps blinking. The TV is 11 years old. What is your recommendation? Is it worth fixing?
Is there anything you can do for one vertical line going down it's yellow. The bottom kind of fluctuates. The last three or four inches from the bottom.
Why, I did reset follow the intrustions ( reset Lamp Error Reset, moved Reset to ON, and “Industry INIT to ON) but TV not turn ON and Led continue flashing? Please help me , Thanks!
Hello I have a 90” sharp and it is doing the same thing but it does not bring up the serial number on the screen like that and the Chanel down and volume down still does not work. Would this be the LED strips? I already replaced the main board.
That fixed it thanks Tampatec.
How do you get into Service Mode of a Sharp Aquos TV Model :LC-80LE632U using the Remote ? Pressing CH - & INPUT while plugging in the TV is not working.Thanks for your tips.
I have a LG 6550 tv that was bought last year. Last week the lower 3rd of the screen begin blinking greyish lines. I unplugged the tv and plugged it back in. I also unplugged the cable box to the tv but it even did the grey lines blinking/flashing with the items disconnected. The only thing that has ever been connected to the tv has been the cable box.
Do you propose the next step is going in and reset to original settings? Or is it an internal issue?
Many thanks my friend it working perfectly can’t thank you enough 👍👍👍👍👍👍👍
I am trying to fix a sharp tv for my friend I confirmed a bad led strip and replaced with parts from shop jimmy I get red flashing light it wont turn on with remote when I push the power button on tv now I get backlight but no input or logo symbol I tried this method is that a mainboard issue I will check voltage from power supply next but figured power supply is good since it turned on when pushing power button on tv thanks for all the great videos I bought led tester you recommended from shop jimmy worked great any advice would be great
It worked thank you so much saved me ton of money!!!!
Thanks lot just used your video tonight to reset mine
I have an older model 2012 - controls are on the left side of TV - same procedure doesn't seem to work on mine at all. Any ideas ? THanks !
I have an issue with my Sharp Aquos LC-52LE810UN. The front panel volume buttons trigger on their own, raising and lowering the volume. I determined this by disabling the front panel buttons, but that just results in a popup in the center saying "the operation is not allowed". Is there a way through the service menu or otherwise I can physically disable the front panel buttons? Thanks.
2 of my hdmi ports quit working on my Sharp Aquos LC-70LE733U. Do you know what’s wrong and how to fix them.