How to Replace Front Steering Knuckle 1997-2006 Jeep Wrangler

Buy Now!
New Steering Knuckle from 1AAuto.com 1aau.to/ia/1AST...
This video shows you how to install a front knuckle on your 1997-2006 Jeep Wrangler.
This process should be similar on the following vehicles:
1997 Jeep Wrangler
1998 Jeep Wrangler
1999 Jeep Wrangler
2000 Jeep Wrangler
2001 Jeep Wrangler
2002 Jeep Wrangler
2003 Jeep Wrangler
2004 Jeep Wrangler
2005 Jeep Wrangler
2006 Jeep Wrangler
Tools you will need:
• Pry Bar 1aau.to/oX5/1AX...
• 22mm Wrench
• 12mm Socket 1aau.to/obGi/1A...
• 14mm Socket 1aau.to/obGi/1A...
• 17mm Socket 1aau.to/obGi/1A...
• 19mm Socket 1aau.to/oaoy/1A...
• 22mm Socket 1aau.to/opH/1AX...
• 32mm Socket 1aau.to/oc9/1AA...
• 36mm Socket 1aau.to/ocf/1AA...
• Brake Caliper Hanger 1aau.to/ojL/1AX...
• Side Cutters
• 5/16 Inch Socket
• Ratchet 1aau.to/obJA/1A...
• Socket Extensions 1aau.to/obGi/1A...
• Torque Wrench 1aau.to/oaNS/1A...
• Gloves 1aau.to/oapU/1A...
• Safety Glasses
• Floor Jack 1aau.to/oacW/1A...
• Hammer
• Jack Stands 1aau.to/oZB/1AX...
• Punch
• Wheel Chocks
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

[@TRQ]

√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money

[@mtblantonjr]

Good video. Gonna likely be replacing the ones on my TJ soon also due to drilling them out to 5/8 for a CavFab steering kit. May be swapping to a better steering kit (RockJock/Currie or TeraFlex most likely).

[@veiledzorba]

Overall, nice video. BUT - you show removal and reinstallation of the WHEEL, but not the ball joints? Why did you go to the trouble of removing the cotter pin remnants when you changed the ball joints anyway? I would have also changed the U-joints while I was there, and I would have done some painting as well.

[@veiledzorba]

Cotter pins are easier to pull with a small screwdriver, an awl, a small drift, or anything that can fit inside the "head" of the thing.

[@Ink0211]

I assume this is the same procedure with a 2000 cherokee? I believe they have the same front axle

[@Zoro09895]

Never give up 😢