GE Dryer Won't Heat - What to Look for & Test
HTML-код
- Опубликовано: 25 дек 2023
- In this video, I show you all of the various different things that could cause your GE Dryer not to heat properly. There are 7-8 different major culprits that can cause it to either not heat or dry properly. Many if not all of these things can be accessed/tested/replaced by a screwdriver and a multimeter.
GE Dryer Timer for GTD42 Units: oemparts.bens-appliances.com/...
Purple Wire Replacement: bens-appliances.com/products/...
Heater Assembly: bens-appliances.com/products/...
Thermostat for Unit (top of pan, to the right of the 2): oemparts.bens-appliances.com/...
Thermostat (top of pan, to the left of the set of 2): oemparts.bens-appliances.com/...
Blower Housing Thermostat: oemparts.bens-appliances.com/...
Upper-right pan High Limit Thermostat: oemparts.bens-appliances.com/...
Tools I use in all videos can be found at my Amazon Idea Page: www.amazon.com/shop/bensappli...
Did this video help you out? Send me a tip, and help me make more Appliance Repair videos for people to watch for free!
PayPal: paypal.me/BensappliancesYT?lo...
CashApp: $BenjaminSchlichter
Affiliate Disclosure Form: bit.ly/3oXeu3B
** Links to external websites and parts may result in me receiving a commission on sales. 
Хобби
It's sad how many people here are dealing with a useless GE dryer that is only 1-2 years old. Myself included. First and last GE product for me. Never again. As if the cost of everything isn't high enough, now we have to deal with appliances that last only a year or two when they used to last decades! Planned obsolescence most likely.
I’m doing on 3 years. Heat stopped working. Gotta trouble shoot tonight cause I can’t afford a new one
Mine was replaced in July and now not heating. It is in an apartment so have a maintenance ticket in since wasn't the purple wire that I was going to repair myself since been several days already without a dryer.
Had a Samsung and was talked into GE at the store and wish I had not because issues with both washer and dryer after just over a year. No issues in almost 5 years with my old Samsung
6 months and the dryer us not getting hot
Had a GE dryer that wasn’t heating but it would spin. Ended up being the purple wire. Thank you for the detailed troubleshooting guide!
did you get it running after replacing purple wire? can you tell me by chance where to buy it?
@@lyndamckinney1287 I ended up re-crimping the burnt end with a new connector as there was enough wire still in tact. Those connectors can be purchased at Home Depot. They're Gardner Bender 1/4 in. Fully Insulated Wire Disconnects in Blue. I used some sandpaper on the heating element spade connector to clean it up. If you wish to buy a new purple wire with both ends pre-crimped, Ben has a link to them in the video description.
Same here...just put a new spade on and it works great
I really appreciate your videos as a guy whose worked with appliances for a long time i really am grateful for having someone who works both sides of the field the product knowledge/sales and the technician/repair
Ben, thank you for all you do. I am a maintenance tech in training, and you are a far greater teacher than what I’ve received from my peers.
Awww, thanks! This is why I do the videos. When I started learning, I realized there were tons of videos I need, and my other guys needed, that just didn't exist. So my goal for the next 3-4 years is just to try to make as many videos on as many different types/styles of appliances I can so people can have a good idea of the baiscs.
Thank you! Burnt off purple wire...replaced spade and works great!
By far the best video I have seen on a GE. Thank you!
Probably the best video of its kind I've seen in years of looking at these. Can't thank you enough for the cllear understandable guidance?
Glad it helped!
my hotpoint dryer, about 14 months old, no heat....after watching a few videos i figured it was the purple wire. and it was....i was thinking on cutting a hole in the back of dryer to get to the purple wire. i wish i wouldve. i couldve fixed it in no time instead of taking the whole thing apart. thank you for the video!
wonderful job on this video! Thank you!
Good information thanks for sharing.
Bought this GE dryer and had it 30 days when it stopped heating. Everything else worked. Took it apart and the purple wire was fried. I tested the heat element and that was bad. Based on the other comments this is a common issue. What's the cause?
hi, really a love the content in your video very informative, thanks to it i did fix my dryer really thanks for sharing keep it up.
Great to hear!
Dryer stopped heating. Blower works, drum turns, replaced the mica heater (still no heat), replaced all 3 thermostats (still no heat), purple wire was not burnt but spade did break off when removing the heating pan the second time to change the thermostats (fixed that). Thoroughly cleaned. Tested power, I have 120 (center/right, center/left)/208 (left/right) on a voltage tester. No fuse present. Getting ready to go pick up a multitester to start checking switches. What happens if I find a bad reading on one of the ohm tests in the video? Running out of things to troubleshoot...
Is there a video replacing the purple wire. Mainly from the plug
My stove is acting up and I foresee having to buy a new one. There’s a discrepancy between the setting temperature and the thermometer read out and it beeps when it’s ready just five minutes after the oven is turned on. It’s a Samsung I’ll NEVER purchase again. My budget is fragile. What would you recommend in a glass top stove/oven that is durable and reliable? I know front handles are more expensive but I love that look. Thank you!
Can someone explain why GE gas dryers don’t have a door or a peep sight with a plug in order to view the igniter and the burner??? Any suggestions on how you can see inside cabinet for viewing
Mine had the burned purple wire. Thanks!!!
That's the culprit so often. I'm going to do a video just on that for the next GE I get
Did you Jane to replace the whole wiring harness, or how did you fix it?
@@GabrielGarcia-vf8uu I do have a video on replacing the harness now, FYI
@@GabrielGarcia-vf8uu I cheaped out and just cut the wire back, and added some wire with a crimp connector and a new female spade end. Make sure that you spend a LOT of time sanding down the spade end on the heater coil to get a shiny finish and good electrical connection or it will burn up again due to high resistance at the connection. You can test by putting a new connector on the spade and putting your meter lead into the rear of the connector and read resistance while moving the connector up and down. If your readings don't jump into the hundreds, then you should be good!
Thanks
Thanks your video truly helped me troubleshoot the purple wire was charred at the connector. I plan to change the connector
Do you know the root cause of the Problem??? If I remake the connection …. How long until it happens again ?
My understanding is the OEM wire is undersized and the replacement is thicker and can handle the amperage better. AFAIK, it was 14awg and the new replacements are all 12awg.
Tested power on both sides and got a reading of 246.2, above the 208 to 240 V range. You suggested it could be a cord or breaker issue. Do you recommend replacing the cord or bringing in an electrician. My electrical panel seems to be fine otherwise.
246 should be OK it is rare to have the voltage higher, but depending on your houses power, it may be normal. It can handle up to 250v I believe OK
With amount of lint maybe a check of the piping would be in order. At a minimum a check of the dryer blower capacity should lead you to clogged piping in the wall another upsell and very necessary for the life of the unit the clothes and light bill.
OK, sir, very informative video. My dryer was running but not heating. I followed all your steps and it was my purple wire burnt. I repaired it and put everything back together. Now the dryer will only run if I hold down the start button. I checked and double checked the door switch. Holding the start button with one hand and If lightly press the door switch with my other hand the light comes on,, then press is a little further and the dryer starts. So, i am thinking that the door switch is working correctly I did notice that the start button is only closed when you hold it down. I am not very good at 110 / 220 volt systems but pretty good at 12 volt stuff. So, i take it once the motor starts something else keeps the current flowing. I also need to mention that my dryer is only 14 months old and has been used very little. Any ideas on what the problem is now? Thank you
Ok, took it back apart the 4th time. Checked everything again. Put it back together and it worked correctly. It might have been the safety switch on the idler pulley. Man,, thanks again for the video. Very helpful.
A centrifugal switch closes when the motor is at speed, energizing the heating element
Do you have a video on how to replace that purple wire? Mine is fried, but I can’t get the end out that is connected to harness to motor
I do not. But I will see if I can make one soon, as I've had a few people ask
Any recommendations on how to remove the end attached to the harness that connects to the motor?
Had issues with this for months. At first is was drying after 2 or 3 times. Then 5 or 6. Finally just opened it all up and low and behold a loose wire connection of a heating element. Now it dries like there was never a problem.
According to some sources, you cannot (should not) perform a Continuity test on a thermistor because they have a high Ohms resistance. Instead, you need to use the ohms setting on the multimeter rather than the simple Continuity test.
I have found that on that type of dryer, the heating element almost never opens, but the lower right wire will burn up and break.
Yep. I just ordered the wires to keep in stock at our store due to how often this is the issue.
Amazing mine was the purple wire burnt
I always just open the door, hold the door switch in and run the dryer and look at the back to see if the heating elements are getting hot or glowing.
Control knob is the first to check. Knob shaft cracks and you have no idea if you are on a heat cycle. Timer knob failures are high
Move the stupid plastic cover!!!
Love it !! ❤❤
I've noticed you haven't been wearing the Maytag hat lately. Did Maytag complain about it or did you decide a change was needed?
uh oh, did Maytag put the kibosh on the uniform and hat????
your driers are much better built than some of the rubbish we have in the uk now
Ouch. I have one of these and it's pretty much the cheapest dryer in the store in the US.
My purple wire burnt off at that connector. Dryer was only 18 months old.
GE sucks no matter how you look at it.
Mine burnt after 24 months.
There is no panel at the bottom where the electrical cords are on my ge dryer.... You have to take the entire back off or take the front off and take the barrel out to access the electricity... It is absolutely ridiculous I just had to pay someone a lot of money to fix my stupid GE dryer
(Ge appliances)..❤..
replacing the motors on these kinda sux. its not horrible horrible, but compared to others, i no likey. When replacing the motor, always order a blower wheel too
Nah, that can't possibly be a GE dryer - the knobs haven't broken off! :/ I probably need to de-lint mine now that I've seen it's OK to take the drum out.
hello i do appliances work and i had a customer that tried to do work on his own dryer and screwed it up more so on that note if you do not feel comfortable working on your appliance please call a tech person
Fixing this for my neighbor, the wire completely melted. Just over a year they have had it, what a shame, planned failures, just like phones and cars. Not all brands. Definitely won’t be reccomend GE to anyone. Funny they charge 30$ for 3 feet of wire too 😂
Sadly, melted wires like this happen in other brands too. Just for some reason the GE is slightly more prevalent. I am working to source the wire factory-direct to try to get the price cheaper. These items even at dealer wholesale are outrageously overpriced, and I am trying to see if we can get the price down to $20 vs. $30-35.
I did all of this due to no heating. Found nothing wrong so I cleaned it out and put it all back together and now it won't start. Fml
where's the uniform/hat 😥
It’s not a Maytag! 😂
I already know who I am and where I work. Uniform not needed.
These new GE dryers are very difficult to repair and not service friendly.
GE dryer failed immaturely very fast. Samsung is the second worst. LG may be more reliable.
I have only ever purchased Whirlpool appliances, and have had great reliability. I had to replace one washing machine that had the drum bracket rust away. The Whirlpool dryer is now 17 years old, with only a heating element and high limit cutoff replaced (less than $100 in parts). The Whirlpool dishwasher is about 13 years old, with only minor parts replaced: lower rack, plastic clips, a drain pump and a rubber gasket (maybe $200 in parts).
@@robertjoseph1592 sorry for accidentally dislike - anything before 2010 is better
Yeah my old whirlpool was a lot easier to work on. Two heating elements and one high limit but finally the drum wore out and stuff wax falling out the bottom. Next one was an old used Kenmore whirlpool . its about 25 years old replaced one heating element on it so far.
The ads at very beginning are REALLY fucking annoying
No heat at 14 months. GE is very poorly designed & built. Stay with Whirlpool