Making A Standalone TDI Wiring Harness for PD EDC16 ECUs, Including BEW,BRM,BHW

Поделиться
HTML-код
  • Опубликовано: 29 окт 2024

Комментарии • 110

  • @Gfunkbus76
    @Gfunkbus76 Год назад +2

    Yellow black in Volkswagen is the x circuit, power generally will cut during crank. Tied into headlights, etc.
    Thanks for the videos!! Going to be doing my wiring this fall.

    • @TDISwaps
      @TDISwaps  Год назад +1

      Glad to help! Thanks for watching!

  • @danielkingery2894
    @danielkingery2894 Год назад +2

    This video is much more easy to follow. I followed the other one when i was harvesting the BEW out of my Golf.
    Im hoping to get to assembling that project this winter.😎

    • @TDISwaps
      @TDISwaps  Год назад

      Ya I was pretty fresh on doing videos and doing wiring at that point lol

  • @timbrwolf1121
    @timbrwolf1121 6 месяцев назад +1

    Planning to put one in an early 90s dakota 4x4. I need a fuel efficient all weather vehicle because I do deliveries. I am obsessed with dakotas, and finding out I can do this so easily...I was instantly sold.

    • @TDISwaps
      @TDISwaps  6 месяцев назад +1

      It's like the best thing since sliced bread! 😂

    • @timbrwolf1121
      @timbrwolf1121 6 месяцев назад +1

      @@TDISwaps Thinking of sticking with the A518/46rh 4 speed auto. Not sure about the torque converter but I can get a diesel valve body kit for it.

    • @TDISwaps
      @TDISwaps  6 месяцев назад

      @timbrwolf1121 unfortunately they do not make a TDI adapter for that

    • @timbrwolf1121
      @timbrwolf1121 6 месяцев назад +1

      @TDISwaps yeah I figured that out just within the last few hours. Changed the plan to finding an ax15 dakota. Swapping in a jeep ax15 for the different bellhousing and input. Then I can swap the tdi in

    • @timbrwolf1121
      @timbrwolf1121 6 месяцев назад

      @TDISwaps if I'm really lucky I'll find a 2.5 manual 4x4 but those are rare. They were usually rwd if they had the 2.5

  • @amorag59
    @amorag59 Год назад +1

    Nice! One thing that helped me was figuring out how to de-pin the master ECU connector (seems it can be different even in the same EDC family) moving an unused signal like air conditioning over to where the clutch pin is (granted you have a tune to switch from auto to manual EDC 16 in the case of BHW to utilize the clutch for cruise control).

    • @TDISwaps
      @TDISwaps  Год назад +1

      Yes cruise control would probably require some pins moving but it's nice to have it running at least!

    • @amorag59
      @amorag59 Год назад +1

      @@TDISwaps Yeah probably an extracurricular for most just starting out. If you do head down that road be careful, the de-pinning how-to is scarce and the videos that do show how always have a few comments asking where to buy new crimped wire due to them getting destroyed with lack of patience lol.

    • @TDISwaps
      @TDISwaps  Год назад +1

      Lol I believe it! This is definitely the "how to keep it simple" video 😂

  • @chapmancollins3519
    @chapmancollins3519 Год назад +1

    Awesome video! No telling how much help you just gave the swap community! *PLEASE* do a CJAA wiring video! I've started getting parts for my Gen 2.5 Monterl swap!

    • @TDISwaps
      @TDISwaps  Год назад

      I don't really have an urge to do the whole swap, but if someone sends me a harness to make for them I'll make the video!

    • @brycehill416
      @brycehill416 10 месяцев назад +1

      @@TDISwaps any way I can get ahold of you, I’m going to do a swap. I’d definitely appreciate some advice and knowledge on a few different aspects.

    • @TDISwaps
      @TDISwaps  10 месяцев назад

      @brycehill416 ya man you can PM me on FB. facebook.com/profile.php?id=100014261163897&mibextid=ZbWKwL

  • @gorillagoldhunters
    @gorillagoldhunters 11 месяцев назад +2

    Awesome video buddy,appreciate this a lot!

    • @TDISwaps
      @TDISwaps  11 месяцев назад

      Glad to help!

  • @flashgordon99999
    @flashgordon99999 Месяц назад +1

    Thanks for this. Where would one find the schematics? Looking for 2006 Jetta BRM in particular. Looking to put one in a Ranger.

    • @TDISwaps
      @TDISwaps  Месяц назад +1

      The only place I know to get them is on the TDI swapped trucks Facebook group

    • @flashgordon99999
      @flashgordon99999 Месяц назад +1

      @@TDISwaps thanks

    • @TDISwaps
      @TDISwaps  Месяц назад

      @flashgordon99999 for sure man! They are in the files section of the group

  • @slodsl
    @slodsl Год назад +2

    VERY NICE HOSS

    • @TDISwaps
      @TDISwaps  Год назад +2

      MANY MANY THANKS HOSS

    • @slodsl
      @slodsl Год назад +1

      GOBBLESS

  • @cinci520
    @cinci520 Год назад +1

    Just taking the plunge into this project, thank you for your video. Maybe a dumb question but after you’re deleting things you don’t want in the harness does someone have to reprogram the ecu? Can this be done on VCDS?

    • @TDISwaps
      @TDISwaps  Год назад +1

      The ECU will need the security immobilizer disabled before this type of harness will work, while that's being done a performance tune with delete is easy to add on, that's all usually done mailing it to a tuner.

    • @cinci520
      @cinci520 Год назад +1

      Thank you very much for the reply, I’ll continue to watch your wiring videos. My swap is for a boat so I’m looking to eliminate as much as possible and then re wire using the connectors

    • @TDISwaps
      @TDISwaps  Год назад +1

      @cinci520 no problem! That sounds like a blast! If I ever get an inboard boat it's gotta happen!

  • @brajanmaksumic1073
    @brajanmaksumic1073 9 месяцев назад +1

    Will this same setup work for edc15? Looking to swap an awx engine code into a pajero 2, and being in europe doesnt make this easier since there are so many different engine codes than back in the states...

    • @TDISwaps
      @TDISwaps  9 месяцев назад

      You will have to use a compilation of both my videos on edc15 and edc16 unfortunately, pins may be different too

  • @thisislargemouth5566
    @thisislargemouth5566 10 месяцев назад +1

    I'm looking to swap a tdi into my old Datsun pickup. I've been leaning toward an ALH but the bike insee the more the BEW seems like a great option as well. If you had your pick, what would take?

    • @TDISwaps
      @TDISwaps  10 месяцев назад +1

      It's a tough call, bew is stronger but has more maintenance, ALH is more dependable, but weaker bottom end, I definitely don't like that fuel leaks on the PDs go right into the oil without you knowing. I usually just base it off price and availability at the end of the day

    • @thisislargemouth5566
      @thisislargemouth5566 10 месяцев назад +1

      @@TDISwaps thanks for the info. Yeah I see way more BEWs and BHWs for sale than ALH but I've seen those ALH with 500,000 miles. I'll probably end up with a BEW based on availability. You've made me confident the wiring isn't that hard. Just salvage as much of the harvest as I can.

    • @TDISwaps
      @TDISwaps  10 месяцев назад

      @thisislargemouth5566 you got it! Now got get one! Haha

    • @vernon44427
      @vernon44427 9 месяцев назад +1

      ​@@thisislargemouth5566alh head on a bhw bottom end. Have the best of both worlds. Not too much extra to do for it to work and lots of write ups on this hybrid

  • @NathanBerger-li3yv
    @NathanBerger-li3yv 7 месяцев назад +1

    I have a BRM and on my wiring diagram I am seeing a data link interface is that something that is there or do I just need the data link wires thank you sir you’ve been a lot of help

    • @TDISwaps
      @TDISwaps  7 месяцев назад +1

      You do not need can bus wiring for basic setup but you do need the k line for OBD communication that should be pin 72 on the big plug

    • @NathanBerger-li3yv
      @NathanBerger-li3yv 7 месяцев назад

      @@TDISwaps I greatly appreciate your help my friend

    • @TDISwaps
      @TDISwaps  7 месяцев назад

      @NathanBerger-li3yv no problem!

  • @rossconverse9067
    @rossconverse9067 Год назад +1

    Thanks!

  • @rossconverse9067
    @rossconverse9067 Год назад +1

    Hi, I went to Facebook and I see there's 2 different TDI swap groups. Can you steer me in the direction of where to find those four pages of schematics. Thanks for the video great job!
    Ross

    • @TDISwaps
      @TDISwaps  Год назад +1

      You will probably want to join both groups, but the PD style engines have a lot more info in the "TDI Swapped Trucks" group. Thanks for watching!

  • @Estebandealba3335
    @Estebandealba3335 Месяц назад +1

    Hi friend, I'm a fan of your videos, I made a 1.9 TDI project in a Jeep Liberty, I tried to make my harness but I'm missing some components, could you help me with the diagram?
    thank you.

    • @TDISwaps
      @TDISwaps  Месяц назад +1

      You have the schematics printed out then?

    • @Estebandealba3335
      @Estebandealba3335 Месяц назад +1

      Yes I had them, but I lost them and now I have nothing.

    • @TDISwaps
      @TDISwaps  Месяц назад

      @Estebandealba3335 I don't have any way to link them on RUclips

  • @aarononeal1462
    @aarononeal1462 3 месяца назад +1

    Do You have a link for those diagrams? I can't seem to find them

    • @TDISwaps
      @TDISwaps  3 месяца назад +1

      If you join the TDI swapped trucks Facebook group, they are in the files section on the right side of the page at the top

  • @jesseTomlinson-lx4mg
    @jesseTomlinson-lx4mg 10 месяцев назад +1

    any chance you number the pins. my brm has diffent wire colours so i understand, but need to find it by pin please.

    • @TDISwaps
      @TDISwaps  10 месяцев назад

      I think you commented twice

  • @leonwilliams2412
    @leonwilliams2412 7 дней назад +1

    Can you posibly make me a loom for bkd retro fit in to a peugeot 306

    • @TDISwaps
      @TDISwaps  7 дней назад

      Well I am usually making these looms using the TDIs wiring like the original BKDs loom. And I'm also always making them standalone like to run without hooking to a factory ve cluster, just universal gauges

  • @IMCABLETV
    @IMCABLETV 5 месяцев назад +1

    So I’m trying to rewire my engine bay I’m building a new dash in my Jetta to be a center seating position with a wrap around dash kinda. I’ll have plenty of room in the new dash and, floor cubbies on the sides to relocate everything.

    • @TDISwaps
      @TDISwaps  5 месяцев назад

      Perfect time to do a custom dash since the VW one sucks anyways haha

    • @IMCABLETV
      @IMCABLETV 5 месяцев назад +1

      @@TDISwaps yeah, I might be needing some help possibly with some questions here and there. New to the whole wiring thing but good at all the custom stuff, the exhaust tunnel is no longer needed because of hood exit. So I’m cutting the floors and tying the front subframe to the rear trailing arms and strut towers. Then building storage bins in the floor all the way up to the driver seat.

    • @TDISwaps
      @TDISwaps  5 месяцев назад

      @IMCABLETV sound like quite a project!

    • @IMCABLETV
      @IMCABLETV 4 месяца назад

      @@TDISwaps I’ll have a channel and videos sometime this year

    • @TDISwaps
      @TDISwaps  4 месяца назад

      @IMCABLETV sweet!

  • @Speedy2222
    @Speedy2222 8 месяцев назад +1

    what tuner did you use so you wont need to use the immobilizer?

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      I bought the software to do it myself

    • @Speedy2222
      @Speedy2222 8 месяцев назад +1

      @@TDISwaps Do you need the gauge cluster to eliminate it or can you just plug into the obd2 port once wired to the ecu and powered on?

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      @Speedy2222 I have a bench test box so I just need the ECU itself

    • @Speedy2222
      @Speedy2222 8 месяцев назад +1

      @@TDISwaps dang the donor i got has no key, only ecu and cluster

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      @Speedy2222 yeah all you need is the ECU to run the engine once the immobilizer is disabled but it has to be bench flashed to disable it so you'd have to mail the ECU into somewhere like me or a tuner.

  • @jamesharless6003
    @jamesharless6003 10 месяцев назад +1

    Any idea where to get connectors?
    Who can tune the computer for this swap as well?

    • @TDISwaps
      @TDISwaps  10 месяцев назад +1

      I get all my connectors from Ali Express. And my tuning all comes from TekMekTronics. I will be getting setup to offer swap delete tuning in the next few months.

    • @jamesharless6003
      @jamesharless6003 10 месяцев назад +1

      @@TDISwaps how about the main round connector to the injectors in a bew motor? That seems impossible to find

    • @TDISwaps
      @TDISwaps  10 месяцев назад +1

      @jamesharless6003 those are hard to find new, but they are usually available used, the part number is 038973121B.

  • @lukeweiser5068
    @lukeweiser5068 Год назад +1

    Hommie posted up in the hotel room doing swap shit

  • @samyones1997
    @samyones1997 8 месяцев назад +1

    Do you have one for sell ? I’m looking to buy one.

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      Well everything has a price, I do have quite a bit of sentimental price on these though. Probably nothing less than 10k. You can find me on Facebook if you are interested though. facebook.com/profile.php?id=100014261163897&mibextid=ZbWKwL

  • @etchoppau
    @etchoppau Год назад +1

    where can i download the schematics? does anyone have a link to them please?

    • @TDISwaps
      @TDISwaps  Год назад

      The Facebook group TDI swapped trucks has the schematics in their files section

  • @marshall4619
    @marshall4619 Год назад +1

    Where did you find the pinouts? Everywhere I've looked I can't find the proper information.

    • @TDISwaps
      @TDISwaps  Год назад +2

      "TDI swapped trucks" group on Facebook has all the info in their files section

  • @julianornelas9304
    @julianornelas9304 10 месяцев назад +1

    Can this work on a 1.8t?

    • @TDISwaps
      @TDISwaps  10 месяцев назад +1

      With the right schematics yes you can wire a 1.8 harness the same way

  • @kristiansoderblom1750
    @kristiansoderblom1750 8 месяцев назад

    Do you know were to find a wiring diagram to a vw 1.9 tdi avf

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      I have not seen good schematics for those wiring setups. I had planned to draw up my own if someone ever sent me a harness to build for them, but so far I have not received one yet to be able to dig into it's wiring

    • @kristiansoderblom1750
      @kristiansoderblom1750 8 месяцев назад +1

      @@TDISwaps Well i can send u mine but i live in Sweden😂

    • @TDISwaps
      @TDISwaps  8 месяцев назад

      @kristiansoderblom1750 ya that would be a bit of shipping... But I do have international shipping options 🤷 🤣

  • @daltonwhitney8062
    @daltonwhitney8062 Год назад +1

    Where can I find the diagrams?

    • @TDISwaps
      @TDISwaps  Год назад +1

      If you are on Facebook, the group "TDI swapped trucks" has all the diagrams in there files section

    • @daltonwhitney8062
      @daltonwhitney8062 Год назад +1

      @@TDISwaps I found them thanks One more question. The mass airflow sensor is not required?

    • @TDISwaps
      @TDISwaps  Год назад +1

      @daltonwhitney8062 i always delete everything possible to minimize issues with wiring. I have tuning to delete everything.

    • @daltonwhitney8062
      @daltonwhitney8062 Год назад +1

      @@TDISwaps sorry for all the idiot questions where do you recommend? I send my EC you to have everything deleted

    • @TDISwaps
      @TDISwaps  Год назад

      @daltonwhitney8062 just depends on what you are looking for, I use TekMekTronics for all my custom tuning, Malone is also good.

  • @ethanmentz7548
    @ethanmentz7548 3 месяца назад

    You rent a hotel room so you got clean white sheets?

    • @TDISwaps
      @TDISwaps  3 месяца назад +1

      Haha, just out of town work trip and nothing to do in the evening 😂

  • @lacybinnie3091
    @lacybinnie3091 Год назад +2

    Can u helo me delete my immobilizrr?

    • @TDISwaps
      @TDISwaps  Год назад

      Unfortunately I don't have the software to do edc16 immobilizer, it has to be sent to a tuner for that

    • @PolishFab
      @PolishFab Год назад +1

      i should be able to do it if you want to send it out

  • @TDISwap
    @TDISwap Год назад +2

    Thanks buddy. This will help my brother out on his.

    • @TDISwaps
      @TDISwaps  Год назад +1

      Glad to get more information out there, PD wiring doesn't need to be a big unknown

  • @HunterMccomb-dz8xt
    @HunterMccomb-dz8xt 3 месяца назад +1

    How much do you charge

    • @TDISwaps
      @TDISwaps  3 месяца назад

      $400 without glow plugs, $450 with. You can PM me here facebook.com/profile.php?id=100014261163897&mibextid=ZbWKwL

  • @jesseTomlinson-lx4mg
    @jesseTomlinson-lx4mg 10 месяцев назад +1

    any chance you number the pins. my brm has diffent wire colours so i understand, but need to find it by pin please.

    • @TDISwaps
      @TDISwaps  10 месяцев назад

      If you are on Facebook, join the group facebook.com/groups/291980407818664/?ref=share&mibextid=NSMWBT they have all the files and schematics you need.

    • @silverbob8656
      @silverbob8656 Месяц назад +1

      @@TDISwaps What if I'm not on Facebook? Is there any other way to obtain this information?

    • @TDISwaps
      @TDISwaps  Месяц назад

      @silverbob8656 I could try download them an email them to you

    • @silverbob8656
      @silverbob8656 Месяц назад +1

      @@TDISwaps Thank you for your very kind offer. My wife just told me that she has a Facebook account that she hasn't used in a couple years, so I had her apply to join the group. Now we're waiting for the mods to approve her.

    • @TDISwaps
      @TDISwaps  Месяц назад

      @silverbob8656 sounds good!