For those of you wondering if the Betaflight 4.4 HD OSD is available on the Goggles V2 with O3 air unit, I haven't been able to get it working There is a new firmware for the V2 on the O3 side (07 firmware) which states "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me with the O3. I checked the goggles menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2, which is a ridiculous issue from the original release of the O3 back in November and still unfixed.
Works fine for me. MAKE SURE your goggles are in O3 mode, not DJI Digital FPV System mode. Then go to Settings->Display and you'll be able to switch Canvas from Normal to HD. Several members on DJI FPV Forum already confirmed it's working for them as well
Stupid question, but anyway - did you switch your goggles V2 to DJI O3 mode before installing the latest firmware? Because if you were in DJI Digital FPV System mode the update wouldn't work
Figured this out... It is being caused by a compatibility issue with the latest V2 firmware (07 firmware) and the WTFOS. When you first install the 07 firmware, the HD Canvas option is available under Display. However, WTFOS no longer works when you switch to the DJI Digital FPV system. The WTFOS website gives you a health check warning, when you resolve the health check, WTFOS starts working but the HD Canvas option disappears.
For INAV 6.0 users, I can confirm this update "somewhat" works. The problem is that on the INAV 6.0 configurator OSD section, if you have BF43COMPAT selected as your Video Format, the Preview screen where you move OSD elements around is still small. One workaround is to select DJIWTF as your Video Format and you'll get a bigger Preview screen. It's not exactly a perfect 1:1 match but close enough. Hopefully the good old INAV devs update the configurator soon to support this. 🙂 Update: I forgot to mention I'm using the original DJI Air Unit (the big one) for my INAV 6.0 drone. I only have one DJI O3 unit but it's on Betaflight 4.4 build, haven't tried the DJI O3 on an INAV build yet.
Great video, I’m always afraid of updating DJI products due to the looming remote ID requirements. I feel they will sneakily slip in some code that bricks the goggles and requires you to tether it. The new Goggles integra most likely has a remote id module built into them yet they haven’t stated that on the website.
The goggles integra have a GPS module, as stated on DJI website. This is to provide Remote ID for the Avata, without requiring plugging in your phone to the goggles.
Any idea why my Goggles 2 cannot record OSD from Betaflight (on 4.4 and 4.5 for 2 of my drones)? OSD recording is important for troubleshooting or recovering aircraft in event of issue. On the latest FW available BOTH Caddx Vista and O3 Air Unit. Goggles are on 01.09.00.00
Goggles 2 and Goggles Integra can record the Betaflight OSD in the Goggle recording. You need to turn on a setting, I can't remember the exact name but it's something like Goggle View Recording.
I’ve no OSD in my Dji goggles 2 with an o3 unit. Any ideas how to sort this at all? Not being able to see my battery life and longitude/latitude if I crash is making long range flights very scary. Thanks
How did you record this OSD? Are you not using betaflight? I really want to record the live image with overlay but can't seem to fix that with O3 and goggles (v)2
That's a feature of the Goggles 2 and Goggles Integra due to it's higher processing power (can re-encode the video in real time). You can't do it with the Goggles v2 unfortunately. There is a way to do it after the fact on the computer with the Goggles v2 and Vista using WTFOS though.
Did dji ever bring out support for recording the osd to the video? I know wtfos has a work around but really just want what we had with fatshark where the osd was natively in the video file.
It’s driven by the goggles so if you have the goggles 2 or integra, it is supported natively. The goggles v1 / v2 can kind of do it with wtfos but only the betaflight elements and not the dji elements.
Not April 1st yet. Please tell me this is true and not a joke! Okay its true. Thanks for telling me this! Worked like a charm on all 6 quads. Can't believe it!
hey I'm a new fpv pilot and I was looking to change where all of my osd elements were on the screen. did you just plug in the drone and then open betaflight or was there more to it?
You need to first setup what they call Canvas Mode (also called MSP Display Port) so that the OSD information is being sent to the goggles. Once you have that setup, yes, you just need to open Betaflight and move around the OSD elements. I have a video on how to do this, it's a big old so make sure to look at the pinned comment: ruclips.net/video/KIis4hB_duQ/видео.html
Thanks. DJI does not support custom fonts right now. Pretty much all you get is the ability of moving the elements to the very edge of the screen and that the existing font becomes smaller/higher resolution.
CORRECTION - also works perfectly fine on Goggles V2 with the latest v01.07 firmware. Tried and confirmed. And question - Is it possible to use a different font with HD?
The 07 firmware for the V2 says "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me on the O3. I checked the menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2.
hello friend, nice your video, I updated mine and it focused as I wanted, recording the osd information. Now take a doubt: I put the Han file to release the FCC but my Inegra at 300m is already bad the signal and the maximum that is coming is 30mbs. can help??
@@Mangorille I don't know, I'll try an earlier version, but I don't think that's it. Could you tell me which Frequency you used and the channel? I wanted to put them on for a test. I don't know if it could be the fact that I'm flying within the city causing the low Mbps value.
Not getting OSD display on goggles 2 with caddx air unit. The goggles 2 have the latest firmware installed 1.05 Flight controller flashed to latest betaflight firmware Betaflight 4.4 config 10.9 Ports MSP UART peripheral set with VTX (MSP + displayport) OSD video format has been tried on PAL and HD. Any other suggestions?
@@timothyciarlette8250 Correct, with Betaflight 4.4 you need to 100% do that step on the Ports tab. Sometimes you need to run the above CLI command as well.
Hello, I have seen your videos and I congratulate you for your contribution and I do everything to the letter but I use the dji goggles 2 with a view and it only gives me 6 or 7 mps what can I do
When you arm the quad, the mbps should jump up to 25 or 50 (depending on your settings). Is that happening? If not, do you see the quad voltage or betaflight OSD being displayed in the goggles?
@@Mangorille Hello, thanks for answering, it does nothing when I put the battery on it goes up to 50 mps but in 5 seconds it returns to 6 mps armed or not armed
@@joseantoniofaria77 Sounds like the air unit is not communicating correctly with the flight controller. Is this something you built yourself or did you buy a bind and fly?
My edges are blurry as well so I position those elements that I only need to check prior to flight there (such as profile #). I like the smaller font though.
Check madstech review of the goggles integra (posted a couple hours ago). Sounds like though smaller fov, he thinks they are a big upgrade optically. He says fov difference is like running goggles 2 at 90% scale for comparison. But you don’t get that double lens refraction blurring on the edges. I might give them a try because the optics on these goggles 2 for me are really awful.
@@KirbyMiller Thanks for the note! I started watching already, it sounds like they ultimately made the blurry edges better by reducing the FOV. Good for people with really blurry edges but bad for those who are able to get good edge to edge clarity on the Goggles 2.
@@Mangorille Hello, just to follow up on this... I just received my Goggles Integra and had a chance to test them this weekend. I have a lot of respect for MadsTech but I totally disagree with him about these goggles. First, yes the FoV is quite noticeably smaller (though that doesn't bother me quite as much as I expected). However, the optics in the Integra are absolutely in no way an improvement over the optics of the Goggles 2. There is a noticeable reflection on the diopter inserts, and this is even with changing out the foam with some custom mods to make sure there is zero light leak whatsoever. It seems like it's actually the OLED screens reflecting / refracting off the corrective inserts. I don't get this with the goggles 2 adjustable diopter (note this is exactly the opposite of what Madstech said). If it matters, I used the -2 lenses in both eyes, and my goggles 2 are adjusted very close to -2 also. I don't normally wear glasses though possibly I should. I have also found that I do not like the fixed battery on the headband. For me it's not more comfortable, or convenient and doesn't help to balance the goggles at all. I definitely prefer a separate battery and then I have the choice to mount it on the strap or not (usually not). Also I can easily carry multiple batteries. I thought I would like the knob to tighten the strap on the Integra, but I don't think it adds anything (if you are the only person using your goggles it doesn't matter). I have an Avata, but I never fly it, so the built in GPS isn't really a factor for me. Also, minor thing, but with the aftermarket foam and the new SD card location on the Integras, it makes it difficult to get the SD card out without removing the foam also. I have never been able to get my goggles to act like a hard drive (Mac) and transfer video through a USB cable so I always have to remove the card to get the recordings. On the plus side though... The joystick controls on the Integras are SOOOO much better than the touch panel on the goggles 2. If you do not wear glasses at all and will not use the included corrective lenses, you could probably (at least in theory) achieve better optics in the Integra because even with the diopter set to 0 on the goggles 2 you are still looking through an additional piece of glass. On the Integra you could just use it as is with no extra glass. Overall, for me I absolutely prefer the Goggles 2 and I will be contacting DJI to see if it's possible to return the Integras. It was worth a try, but for most people I couldn't recommend them.
@@KirbyMiller Thanks for sharing, I was thinking of swapping my Goggles 2 for the Integra after seeing MadTech's video but now I'm thinking twice. I was looking up the FOV of the various goggles and was surprised to see that the FOV of the Goggles 2 is actually a tad bit less than the V2! I suspect if you fly them back to back, you'll miss the extra FOV. It sucks that we don't have that perfect goggles yet and that is why I still have both the V2 and Goggles 2. I just want a V2 with the 1080p OLED and the more powerful processor so that I can capture the OSD on the video feed. Not asking for much right ;)
Are you asking if the Goggles 2 supports the full Betaflight OSD? If so, it looks like it does. I haven't come across any items not supports (mind you I don't use GPS so can't confirm GPS specific OSD elements). The Goggles 2 does support the older air units, there are a few features missing but it is supported with the Dec 8th backwards compatibility firmware.
@@Mangorille oh yea, this is SUPER annoying! I believe DJI can fix it in 5 mins but will they do it? Also, I don't understand why G2 and V2 goggles don't support Mavic 3 and Mini 3 as they as well on O3 systems
Thanks for your help making this video! But I am not able to make it work, I also have WTFOS, i did 3 times the procedure you showed and that looks simple to me. The standart / HD menu disappears and then comes back but I could never get an OSD on my O3. I tried on bf4.3 and 4.4 and on 2 differents FCs :( where vistas were plugged before with osd working. It looks simple, I don't get why it does not work. I have no idea what to try next :/ I can get video on my O3 but no OSD. Can my o3 be broken, like, only the serial part?
Did you try these instructions? There is a compatibility issue with the latest firmware on the O3 side and WTFOS. WTFOS & V01.07.0000 COMPATIBILITY Issue Fix | DJI Goggles V2 Gets Native Betaflight 4.4 HD OSD ruclips.net/video/3ZzTIVnrs20/видео.html
@@Mangorille thanks your your answer, yes I followed your other guide too So the osd device to MSP and with the added the command about msp serial (x-1) on bf4.3 and with the config port msp+displayport on bf4.4. I did everything I found on RUclips and reddit before I wanted to ask you for some help, i don't like asking having try nothing before 🙈 I have only one goggle and one O3 so I have no idea if my o3 is faulty, or my v2 have another issue. (I am engineer in electronics, normally I can solve a lot of shit like this, but I am out of ideas after one week of troubleshooting) Something weird also is that I can't connect my o3 to USB (to update the firmware) without supplying it (with a lipo). So maybe smth is wrong with it, even though the video feed works. Sorry for breaking your head, it breaks mine too I wanted to share ahah
@@mathy378 Hmm, the fact that you don't get any OSD could be a wiring issue or a betaflight software issue. However, when you say that you can't do the software update without having a LIPO connected makes me think something is up with the wiring. Can you do a software update when the O3 cable is disconnected?
@@Mangorille I put the gray (o3 tx) to the rx of the fc and the white (o3 rx) to the tx fc, right where it works with the vista and wtfos 🤷♂️ I flashed several times my fc in 4.3 and 4.4 to try out this. Also I tried on another fc, same serial than a vista again, bf 4.3, all cmd set in cli. I can't see the device in DJI assistant without lipo plugged. So I can't upgrade it, I did it with lipo to last version of o3 available, 1.02(?) If I remember well Thank you for your answer
@@dax4812 You are correct that WTFOS had it for a while, it even has custom HD fonts and icons. I made a video about this a while ago. Native DJI hasn't had HD OSD.
The 07 firmware for the V2 says "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me on the O3. I checked the menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2.
For those of you wondering if the Betaflight 4.4 HD OSD is available on the Goggles V2 with O3 air unit, I haven't been able to get it working There is a new firmware for the V2 on the O3 side (07 firmware) which states "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me with the O3. I checked the goggles menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2, which is a ridiculous issue from the original release of the O3 back in November and still unfixed.
Works fine for me. MAKE SURE your goggles are in O3 mode, not DJI Digital FPV System mode. Then go to Settings->Display and you'll be able to switch Canvas from Normal to HD. Several members on DJI FPV Forum already confirmed it's working for them as well
Stupid question, but anyway - did you switch your goggles V2 to DJI O3 mode before installing the latest firmware? Because if you were in DJI Digital FPV System mode the update wouldn't work
@@K1200S08 Yes sir, I did. I'll continue troubleshooting tonight and see what is up.
Figured this out... It is being caused by a compatibility issue with the latest V2 firmware (07 firmware) and the WTFOS. When you first install the 07 firmware, the HD Canvas option is available under Display. However, WTFOS no longer works when you switch to the DJI Digital FPV system. The WTFOS website gives you a health check warning, when you resolve the health check, WTFOS starts working but the HD Canvas option disappears.
@@Mangorille I try to post the exact procedure how to make both O3 and WTFOS work, but youtube keeps deleting my post. Don't know why...
Perfect, it's working with dji integra+BT4.4. Just select option (VTX+DISPLAYPORT) for UART with Cadxx air unit
Thanks for sharing, happy flying!
For INAV 6.0 users, I can confirm this update "somewhat" works. The problem is that on the INAV 6.0 configurator OSD section, if you have BF43COMPAT selected as your Video Format, the Preview screen where you move OSD elements around is still small. One workaround is to select DJIWTF as your Video Format and you'll get a bigger Preview screen. It's not exactly a perfect 1:1 match but close enough. Hopefully the good old INAV devs update the configurator soon to support this. 🙂
Update: I forgot to mention I'm using the original DJI Air Unit (the big one) for my INAV 6.0 drone. I only have one DJI O3 unit but it's on Betaflight 4.4 build, haven't tried the DJI O3 on an INAV build yet.
Thanks for sharing!
The only downside is that you need to recompile the firmware so the crosshairs will be in the center.
FINALLY! this made me go nuts that all the osd nonsense is in the middle
Yup, I loved the WTFOS on the old vistas because they had this all figured out but finally DJI is catching up!
Thanks for showing this, super easy to do!
Great video, I’m always afraid of updating DJI products due to the looming remote ID requirements. I feel they will sneakily slip in some code that bricks the goggles and requires you to tether it. The new Goggles integra most likely has a remote id module built into them yet they haven’t stated that on the website.
The goggles integra have a GPS module, as stated on DJI website. This is to provide Remote ID for the Avata, without requiring plugging in your phone to the goggles.
@@deice3 thank you for clarifying.
Hear you, especially if they don't allow a downgrade.
@@Mangorille exactly, that little stunt they did with the Avata makes me think twice
thx, now works
Great, happy flying!
Works great here thank you!
Thanks for confirming. Happy flying!
Any idea why my Goggles 2 cannot record OSD from Betaflight (on 4.4 and 4.5 for 2 of my drones)? OSD recording is important for troubleshooting or recovering aircraft in event of issue.
On the latest FW available BOTH Caddx Vista and O3 Air Unit.
Goggles are on 01.09.00.00
Goggles 2 and Goggles Integra can record the Betaflight OSD in the Goggle recording. You need to turn on a setting, I can't remember the exact name but it's something like Goggle View Recording.
I’ve no OSD in my Dji goggles 2 with an o3 unit. Any ideas how to sort this at all? Not being able to see my battery life and longitude/latitude if I crash is making long range flights very scary.
Thanks
Try the instructions in the video below. Make sure to look at the pinned comment.
ruclips.net/video/KIis4hB_duQ/видео.html
Thus betaflight 4.5 work also in dji fpv rc2? Im struggling to set my fpv rc2 to betaflight 4.5 the reciever tab thus not read the fpv rc 2..
Which goggles and air unit do you have? Check out this video: ruclips.net/video/tYomxAbQ7Vs/видео.html
How did you record this OSD? Are you not using betaflight? I really want to record the live image with overlay but can't seem to fix that with O3 and goggles (v)2
That's a feature of the Goggles 2 and Goggles Integra due to it's higher processing power (can re-encode the video in real time). You can't do it with the Goggles v2 unfortunately. There is a way to do it after the fact on the computer with the Goggles v2 and Vista using WTFOS though.
Did dji ever bring out support for recording the osd to the video? I know wtfos has a work around but really just want what we had with fatshark where the osd was natively in the video file.
It’s driven by the goggles so if you have the goggles 2 or integra, it is supported natively. The goggles v1 / v2 can kind of do it with wtfos but only the betaflight elements and not the dji elements.
Not April 1st yet. Please tell me this is true and not a joke! Okay its true. Thanks for telling me this! Worked like a charm on all 6 quads. Can't believe it!
No problem, happy flying!
What about iNav 6.0? It emulates BF OSD from what I understood - does HD OSD also work now?? THANKS
I don't use iNav, will wait for someone else to respond.
Whats with custom fonts and INAV ?
hey I'm a new fpv pilot and I was looking to change where all of my osd elements were on the screen. did you just plug in the drone and then open betaflight or was there more to it?
You need to first setup what they call Canvas Mode (also called MSP Display Port) so that the OSD information is being sent to the goggles. Once you have that setup, yes, you just need to open Betaflight and move around the OSD elements. I have a video on how to do this, it's a big old so make sure to look at the pinned comment: ruclips.net/video/KIis4hB_duQ/видео.html
@@Mangorillethank you
Great content bro! Do you have any idea how to get the HD fonts installed? I’m having trouble with that
Thanks. DJI does not support custom fonts right now. Pretty much all you get is the ability of moving the elements to the very edge of the screen and that the existing font becomes smaller/higher resolution.
@@Mangorille thank you! I feel better knowing that I didn’t screw it up myself
@@Kmart_FPV No problem, happy flying!
I have HD switched on and my quad is 4.4 but I am still unable to see the custom OSD settings show up on the goggles 2. Is there a step I am missing?
Did you do all the settings to turn on the MSP Displayport? ruclips.net/video/KIis4hB_duQ/видео.html
Man, I've been waiting for this for weeks and it's still incomplete. Now I'm sitting here wishing for custom fonts lol
Ya, that's the problem with DJI and why so many love the V2 and the WTFOS.
CORRECTION - also works perfectly fine on Goggles V2 with the latest v01.07 firmware. Tried and confirmed.
And question - Is it possible to use a different font with HD?
Without rooting with WTFOS?
@@harishgowtham_ I use O3 air unit, so no WTFOS, no root, etc.
@@K1200S08 Okay
@@K1200S08 i use og air unit, hope DJI supports that too
The 07 firmware for the V2 says "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me on the O3. I checked the menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2.
can you enable all the gps info such as coordinates sats etc?
I don't use GPS so I can't confirm myself but so far all the elements I've tried have worked.
hello friend, nice your video, I updated mine and it focused as I wanted, recording the osd information. Now take a doubt: I put the Han file to release the FCC but my Inegra at 300m is already bad the signal and the maximum that is coming is 30mbs. can help??
Was the range and mbps okay before you did the upgrade?
@@Mangorille I already updated to the last one. 01.02.0000
@@gabrielpires2008 What happens if you downgrade to a prior version? Does the same issue happen?
@@Mangorille I don't know, I'll try an earlier version, but I don't think that's it. Could you tell me which Frequency you used and the channel? I wanted to put them on for a test. I don't know if it could be the fact that I'm flying within the city causing the low Mbps value.
Not getting OSD display on goggles 2 with caddx air unit. The goggles 2 have the latest firmware installed 1.05
Flight controller flashed to latest betaflight firmware
Betaflight 4.4 config 10.9
Ports MSP UART peripheral set with VTX (MSP + displayport)
OSD video format has been tried on PAL and HD.
Any other suggestions?
Try running these two commands in the CLI. Sometimes these are needed to get it working:
set osd_displayport_device=MSP
save
@@Mangorille This and "Ports MSP UART peripheral set with VTX (MSP + displayport)" is what fixed it on the Integra with air unit.
@@timothyciarlette8250 Correct, with Betaflight 4.4 you need to 100% do that step on the Ports tab. Sometimes you need to run the above CLI command as well.
I Confirmed that it is now working with goggles v2 and the O3 with new firmware
Do you have WTFOS installed on your v2?
@@Mangorille no wtfos. And I can see the HD Canvas mode option
Hello, I have seen your videos and I congratulate you for your contribution and I do everything to the letter but I use the dji goggles 2 with a view and it only gives me 6 or 7 mps what can I do
When you arm the quad, the mbps should jump up to 25 or 50 (depending on your settings). Is that happening? If not, do you see the quad voltage or betaflight OSD being displayed in the goggles?
@@Mangorille Hello, thanks for answering, it does nothing when I put the battery on it goes up to 50 mps but in 5 seconds it returns to 6 mps armed or not armed
on the osd voltage mark 0.00
@@joseantoniofaria77 Sounds like the air unit is not communicating correctly with the flight controller. Is this something you built yourself or did you buy a bind and fly?
Thats amazing! Just too bad that i can't see the edges of my screen (sharp) anyway, so i feel the previous positioning was just about right anyway ;-)
My edges are blurry as well so I position those elements that I only need to check prior to flight there (such as profile #). I like the smaller font though.
Check madstech review of the goggles integra (posted a couple hours ago). Sounds like though smaller fov, he thinks they are a big upgrade optically. He says fov difference is like running goggles 2 at 90% scale for comparison. But you don’t get that double lens refraction blurring on the edges. I might give them a try because the optics on these goggles 2 for me are really awful.
@@KirbyMiller Thanks for the note! I started watching already, it sounds like they ultimately made the blurry edges better by reducing the FOV. Good for people with really blurry edges but bad for those who are able to get good edge to edge clarity on the Goggles 2.
@@Mangorille Hello, just to follow up on this... I just received my Goggles Integra and had a chance to test them this weekend. I have a lot of respect for MadsTech but I totally disagree with him about these goggles. First, yes the FoV is quite noticeably smaller (though that doesn't bother me quite as much as I expected). However, the optics in the Integra are absolutely in no way an improvement over the optics of the Goggles 2. There is a noticeable reflection on the diopter inserts, and this is even with changing out the foam with some custom mods to make sure there is zero light leak whatsoever. It seems like it's actually the OLED screens reflecting / refracting off the corrective inserts. I don't get this with the goggles 2 adjustable diopter (note this is exactly the opposite of what Madstech said). If it matters, I used the -2 lenses in both eyes, and my goggles 2 are adjusted very close to -2 also. I don't normally wear glasses though possibly I should. I have also found that I do not like the fixed battery on the headband. For me it's not more comfortable, or convenient and doesn't help to balance the goggles at all. I definitely prefer a separate battery and then I have the choice to mount it on the strap or not (usually not). Also I can easily carry multiple batteries. I thought I would like the knob to tighten the strap on the Integra, but I don't think it adds anything (if you are the only person using your goggles it doesn't matter). I have an Avata, but I never fly it, so the built in GPS isn't really a factor for me. Also, minor thing, but with the aftermarket foam and the new SD card location on the Integras, it makes it difficult to get the SD card out without removing the foam also. I have never been able to get my goggles to act like a hard drive (Mac) and transfer video through a USB cable so I always have to remove the card to get the recordings.
On the plus side though... The joystick controls on the Integras are SOOOO much better than the touch panel on the goggles 2. If you do not wear glasses at all and will not use the included corrective lenses, you could probably (at least in theory) achieve better optics in the Integra because even with the diopter set to 0 on the goggles 2 you are still looking through an additional piece of glass. On the Integra you could just use it as is with no extra glass.
Overall, for me I absolutely prefer the Goggles 2 and I will be contacting DJI to see if it's possible to return the Integras. It was worth a try, but for most people I couldn't recommend them.
@@KirbyMiller Thanks for sharing, I was thinking of swapping my Goggles 2 for the Integra after seeing MadTech's video but now I'm thinking twice. I was looking up the FOV of the various goggles and was surprised to see that the FOV of the Goggles 2 is actually a tad bit less than the V2! I suspect if you fly them back to back, you'll miss the extra FOV. It sucks that we don't have that perfect goggles yet and that is why I still have both the V2 and Goggles 2. I just want a V2 with the 1080p OLED and the more powerful processor so that I can capture the OSD on the video feed. Not asking for much right ;)
Does it have custom fonts or just the standard dji fonts?
Standard DJI fonts only.
I updated my goggles and the hd canvas shows up in the options but for some reason I can’t get any osd to display and I turned hd on in betaflight
I follow this sted by step, but don`t get Ann osd from betaflight in the goggles😢
Did you setup the canvas mode to begin with? I've got instructions for the o3 here: ruclips.net/video/KIis4hB_duQ/видео.html
You wire it up to uart? Make sure to set your ports up and dissable the aux channel in transmitter betaflight tab.
Is the full osd support for the goggles v2 supported too?
I buy all new and dont want the googles 2 because no support for older air units caddx etc.
Are you asking if the Goggles 2 supports the full Betaflight OSD? If so, it looks like it does. I haven't come across any items not supports (mind you I don't use GPS so can't confirm GPS specific OSD elements). The Goggles 2 does support the older air units, there are a few features missing but it is supported with the Dec 8th backwards compatibility firmware.
@@Mangorille no i ask if the googles V!2 not the googles 2 .
I heared that the googles 2 dont support older Air Units...
@@peterpan1417 The Goggles 2 supports the older air units. Check this out: ruclips.net/video/P7GkbQ2UKHU/видео.html
@@Mangorille thanks for info but i buyed now the googles v2 i get a good offer ...i get one near new for 380,- Euro
@@peterpan1417 The V2 is a great goggle still, congrats on the purchase.
And can you change the OSD font in Goggles 2 and put it in HD as well as in v2?
it would be great. Does anybody knows?
No, in HD mode the font just becomes smaller.
@Mangorille thank you, anyway it is better than nothing. Dji at least gave something
@@irelandfpv Ya, now they just need to fix the loss of bindings when changing modes on the V2 ;)
@@Mangorille oh yea, this is SUPER annoying! I believe DJI can fix it in 5 mins but will they do it? Also, I don't understand why G2 and V2 goggles don't support Mavic 3 and Mini 3 as they as well on O3 systems
Thanks for your help making this video!
But I am not able to make it work, I also have WTFOS, i did 3 times the procedure you showed and that looks simple to me. The standart / HD menu disappears and then comes back but I could never get an OSD on my O3. I tried on bf4.3 and 4.4 and on 2 differents FCs :( where vistas were plugged before with osd working.
It looks simple, I don't get why it does not work.
I have no idea what to try next :/ I can get video on my O3 but no OSD. Can my o3 be broken, like, only the serial part?
Did you try these instructions? There is a compatibility issue with the latest firmware on the O3 side and WTFOS.
WTFOS & V01.07.0000 COMPATIBILITY Issue Fix | DJI Goggles V2 Gets Native Betaflight 4.4 HD OSD
ruclips.net/video/3ZzTIVnrs20/видео.html
@@Mangorille thanks your your answer, yes I followed your other guide too
So the osd device to MSP and with the added the command about msp serial (x-1) on bf4.3 and with the config port msp+displayport on bf4.4.
I did everything I found on RUclips and reddit before I wanted to ask you for some help, i don't like asking having try nothing before 🙈
I have only one goggle and one O3 so I have no idea if my o3 is faulty, or my v2 have another issue.
(I am engineer in electronics, normally I can solve a lot of shit like this, but I am out of ideas after one week of troubleshooting)
Something weird also is that I can't connect my o3 to USB (to update the firmware) without supplying it (with a lipo). So maybe smth is wrong with it, even though the video feed works.
Sorry for breaking your head, it breaks mine too I wanted to share ahah
@@mathy378 Hmm, the fact that you don't get any OSD could be a wiring issue or a betaflight software issue. However, when you say that you can't do the software update without having a LIPO connected makes me think something is up with the wiring. Can you do a software update when the O3 cable is disconnected?
@@Mangorille I put the gray (o3 tx) to the rx of the fc and the white (o3 rx) to the tx fc, right where it works with the vista and wtfos 🤷♂️
I flashed several times my fc in 4.3 and 4.4 to try out this. Also I tried on another fc, same serial than a vista again, bf 4.3, all cmd set in cli.
I can't see the device in DJI assistant without lipo plugged. So I can't upgrade it, I did it with lipo to last version of o3 available, 1.02(?) If I remember well
Thank you for your answer
@@mathy378 Do you see the battery voltage from the quad displayed in the goggles?
hi i have caddx vista dji 2 and i only get 6mps
Probably the low power mode is on. After you arm the quad it should go up again to 50mbps
I have controller 2 + air unit + goggles v2. Works?
Which air unit do you have?
@@Mangorille air unit and caddx lite. Not the new O3
@@diego424 Unfortunately will not work. You either need the O3 with Goggles V2 or the prior generation air units with a Goggles 2.
Is the FCC hack still working?
Yes it is.
Wasnt this already working on BF 4.3?
Nope unless you used WTFOS on the V1/V2. This just started working after DJI made a firmware update yesterday.
@@Mangorille Then I was wrong, I thought V2's had hd osd with vistas with wtfos, and G2 had hd os natively on 03 units.
@@Mangorille these days, I will put 4.4 on my drone to try on V2 + 03
@@dax4812 You are correct that WTFOS had it for a while, it even has custom HD fonts and icons. I made a video about this a while ago. Native DJI hasn't had HD OSD.
@@dax4812 I'm trying it now, still no luck.
So goggles v2 doesn’t get it
V2 works with v01.07 firmware. Tested with O3
@@K1200S08 Test it on an air unit, vista and let us know.
@@JDDupuy Note, we are taking about DJI FPV Goggles V2, not DJI Goggles 2!
@@K1200S08 So there is a new update for V2's ?
The 07 firmware for the V2 says "Added support for Betaflight 4.4 HD OSD when used with DJI O3 Air Unit." However, it does NOT work for me on the O3. I checked the menu as well and it doesn't have this same HD Canvas mode option. Also, note that your bindings still get forgotten when changing modes on the V2.
And we have remote id for free😢
Shouldn't on the O3 and Goggles 2. None of those have GPS built into them and there is no need to connect to your phone to fly.
There's also some new packedge dji-moonlight-shim in WTFOS. Did you test it already? Trying to find some legit video how to use it.
I haven't, looks like it's for streaming games from your computer? I've got a set of VR goggles already so probably won't be playing with that.
@@Mangorille more likely it would be for people practicing on sim with it.
@@Faronsky Interesting idea. Now that could be cool. I'll play around with it.