PUBLIC SERVICE ANNOUNCEMENT!!! Look closely at how all the pulleys line up with each other. The small flat idler pulley mounted farthest to the rear of the mower is mounted too close to the frame causing it to be out of line with the other pulleys. Take that pulley off and put a few washers under it to space it away from the frame a little farther so that it lines up better with the other pulleys. You’re welcome.
@@fn6553 Damn. Make sure the tension arm isn’t seized and it has spring tension on it. Also, make sure the belt is on correctly. I have a RUclips video showing exactly how it goes on. Other than that, I don’t know what else to suggest
Ariens quality control and design is a joke. The pulleys are out of alignment from the factory! Their warranty is a joke. They only care about selling you this garbage mower nothing else.
Belt lasted 15 hours on my XD 52. The idler pulley was off about 3/8 inch. Placed washers to lower it to proper height and it is fine. No where have I seen a recall or tech service bulletin stating this problen. Ariens needs to own up to the mistake and let owners know of a potential problem.
This mower may have a factory defect.The idler pulley is not level with hydro trans pulley on right side setting on mower It throws belt off.I added washers 1/4 to 5/16 thick to lower idler pulley.
First of all, this guy makes it look to be easier than what actually is. He is using a lift to work on it, something that 98% of users don't have access to it like myself. So working with this machine at ground level is definitely not an easy task. I have replaced the drive belt 3 times and the idler pulley once and my machine has been used only 191.2 hours. I believe that the premature pulley and belt failure is due to the huge misalignment on the pulley as that issue put so much stress on each other. Today I have replaced the belt for the 3rd time and added several washers to the idler pulley spacer to correct the issue, something that the manufacturer should definitely be responsible for as per their design flaw, but will they?? You know the answer.
Mine has 190hrs and it pitched the drive belt for the first time last night. I was able to get it back on and finish the job but it is NOT an easy task with the mower on the ground in the middle of a field in the dark. Luckily the belt didnt break so it was not necessary to remove the other belt. But did have to loosen the tensioner that holds the spring completely to get enough slack on the idler arm to get the belt back on.
Hi I own 60 inch iKon I've replaced the starter switch three times and the solenoid once my left axle gear box is leaking and I just replaced the drive belt today and I have 125 hours on it but I do mow about 8 acres or so week with it a so maybe the wear on it doing but the positive of it I'm learning how fix it
I can't believe all of the negative comments! I've had my Ariens Ikon X52 for about six or seven years now. I used it one summer for a lawn business and have 2003.9 hours on it according to the hours meter. Since buying the mower, I have only had to change this belt ONE TIME and came to this video because it just broke for the second time since I've owned it. I have changed the deck belt about three times but that is a very easy process. Love my Ariens mower!
My Ikon XL has 100 hours on it and for some reason, i believe the belt tensioner pully is making a clunking sound every few seconds and I can see it moving side to side. Is it possible this needs to be tightened or something?
Thanks for asking! That tensioner pully isn't adjustable, so you shouldn't need to perform any service with it. It's hard to guess what the issue might be, which is why we suggest contacting your nearest Ariens dealer for diagnosis. Our dealers are an extension of our team and will be able to help you to a resolution. If they determine the issue is the result of a manufacturing defect and your unit is still within the 3-year warranty period, the replacement parts and service would be covered. Click here to find an Ariens servicing dealer in your area: www.ariens.com/en-us/dealer-locator
@@AriensChannel Thanks for the reply, I will check them out. I also checked my mower last night and could not reproduce the problem when I cold started it so I think maybe the mower belt just had a little slack in it that was causing the tensioner pully to bounce a little when it was warm. So it's possible I have no problem and that was just the pully doing its job. It was just weird because I would hear a little "thunk" every time that pulley was tugged but the mower seems fine now. I ordered an OEM belt to have on hand just in case mine goes bad.
Hi I have a 60" IKON XL and the pulling system is different, can you show me how it goes on? I have pictures if I can send them to you and we can speak more about this.
Thanks for asking, Todd. The hydraulic belt routing is actually identical on all Ikon XD-series models and should match this video. Was it another system you were thinking of?
@@AriensChannel It was hard to see the belt routing when he put it on, maybe show THE ENTIRE BELT on after yall are done. But the video did help, she is p and running so THNK YOU!
We're sorry that happened to you, Jarred. The manual linked below is an older version of your unit, but the hydro belt routing illustration in figure 34 on page 26 applies to your unit: apache.ariens.com/manuals/05167900C_ENG.PDF
I just bought th Ariens Ikon Xd52 …. Why does my drive belt keep popping!!! This is now my 3rd belt I’m replacing … the zero only has 41hrs on it … it’s getting frustrating… should I have gone with a John Deer !!
Did you figure anything out on this? I have only had my Ariens Ikon XD 52 for a few months and my drive belt just popped off too (after my PTO belt a month before it). Actually it seemed to "split" with an string coming out from inside it and getting tangled in the mower's mechanical components. Pretty frustrating as a first time ZTR owner.
Hi Jeffrey, we're very sorry to hear about that. We can't say for certain what the issue is, but your nearest Ariens dealer will be able to diagnose the issue after a physical inspection of your unit. Use our dealer locator tool to find an Ariens servicing dealer in your area: www.ariens.com/en-us/dealer-locator
I agree Alyosha! I have a brand new machine with less than 17 hours. Nothing but problem after problem. Very first Ikon XD 60 had to be returned back to Lowes bc the PTO switch would not engage. This new unit keeps breaking drive belts.
@@jonathancobb1411 We're sorry to hear about your experience, Jonathan, and we'd like to guide you to a solution. If you're experiencing these issues we strongly advise you to contact your nearest Ariens servicing dealer. Our independently owned and operated dealers are an extension of our team and will be able to diagnose and resolve the issues. Additionally, if your unit is still within the three-year warranty period, issues which are a result of a manufacturing defect are covered. Use the dealer locator tool we linked here to find a dealer in your area: www.ariens.com/en-us/dealer-locator
Thanks for asking! This belt is Ariens part number 07200718, which can be purchased at your nearest Ariens dealer, or at our online parts store: www.ariens.com/en-us/parts/list?model=&serial=&search=&query=07200718
Thanks for sending me to the website that I’ve been on several times. And also for not answering my question. I clicked on the link and there were no matches found for that part number. This is the problem with companies such as ariens. I purchased a zero turn mower and I love it but when something goes wrong there is zero help. Sure look at all the cool attachments but can’t answer one simple question such as “what size belt is this?”
@@fancyfeathersfarm1447 Hi there, we're sorry that you couldn't access the product display page on our parts site. If you continue experiencing difficulty, try a different internet browser like Google Chrome. As for that belt, its effective length is 56.8", its center distance is 21.9", its top width is 0.50", its angle is 34 degrees and its thickness is 0.31". If you'd like more help finding the right belt for your unit, you can also reach out to your nearest Ariens dealer at the link below. We're always happy to help! www.ariens.com/en-us/dealer-locator
Ariens , I did access the website but after entering the part number that you gave it said, sorry no matches were found. Still don’t know the size of the belt??????????????? My internet browser is not the problem. I just need a simple answer to a simple question. What size hydro drive belt goes on an ariens ikon x zero turn?
@@fancyfeathersfarm1447 Hi there. We're sorry for the frustration. Please email marketing@ariensco.com with your email address and phone number. We're going to have our RapidCare customer support team reach out to you personally. Thank you.
Looked at my ikon dx 60,makeing intermitent horrable noise,,240 HOURS the hydro idler pully,thanks aerens .your crap ant much in my.Wont do business w u ever again!!!! Cheapley made...
3/8 for belt cover and tap screws. 9/16 for tension nut. 1/2 for heat shield. You're welcome.
You the real mvp
You dropped this 👑
Thank you so much ❤🎉
PUBLIC SERVICE ANNOUNCEMENT!!! Look closely at how all the pulleys line up with each other. The small flat idler pulley mounted farthest to the rear of the mower is mounted too close to the frame causing it to be out of line with the other pulleys. Take that pulley off and put a few washers under it to space it away from the frame a little farther so that it lines up better with the other pulleys. You’re welcome.
I did this, but the belt still comes off and is a pain. Tearing up the fans also, less then 100 hours.
@@fn6553 Damn. Make sure the tension arm isn’t seized and it has spring tension on it. Also, make sure the belt is on correctly. I have a RUclips video showing exactly how it goes on. Other than that, I don’t know what else to suggest
thanks. arions engineers are morons
Ariens quality control and design is a joke. The pulleys are out of alignment from the factory!
Their warranty is a joke. They only care about selling you this garbage mower nothing else.
9
Belt lasted 15 hours on my XD 52. The idler pulley was off about 3/8 inch. Placed washers to lower it to proper height and it is fine. No where have I seen a recall or tech service bulletin stating this problen. Ariens needs to own up to the mistake and let owners know of a potential problem.
I agree it’s the only way to correct the problem and they better warranty it 😮
This mower may have a factory defect.The idler pulley is not level with hydro trans pulley on right side setting on mower It throws belt off.I added washers 1/4 to 5/16 thick to lower idler pulley.
First of all, this guy makes it look to be easier than what actually is. He is using a lift to work on it, something that 98% of users don't have access to it like myself. So working with this machine at ground level is definitely not an easy task. I have replaced the drive belt 3 times and the idler pulley once and my machine has been used only 191.2 hours. I believe that the premature pulley and belt failure is due to the huge misalignment on the pulley as that issue put so much stress on each other. Today I have replaced the belt for the 3rd time and added several washers to the idler pulley spacer to correct the issue, something that the manufacturer should definitely be responsible for as per their design flaw, but will they?? You know the answer.
I know! Truth! Here he is with a brand new mower in a clean shop with a hydraulic table.Yeah ,easier than crawling under the thing
Replacing the drive belt on my mower again.
Should’ve purchased a different mower.
Mine has 190hrs and it pitched the drive belt for the first time last night. I was able to get it back on and finish the job but it is NOT an easy task with the mower on the ground in the middle of a field in the dark. Luckily the belt didnt break so it was not necessary to remove the other belt. But did have to loosen the tensioner that holds the spring completely to get enough slack on the idler arm to get the belt back on.
Hi I own 60 inch iKon I've replaced the starter switch three times and the solenoid once my left axle gear box is leaking and I just replaced the drive belt today and I have 125 hours on it but I do mow about 8 acres or so week with it a so maybe the wear on it doing but the positive of it I'm learning how fix it
That's all fine and good with a new clean machine. Do it to one that has been out in field and has been abused as is most are.
This is really fkn ridiculous to change a damn drive belt.. I should have bought a diff mower..
Nut /wrench sizes and torque specs would be a great touch to this video..
Really great that you made a vid how to do this. Our last ones just say...SEE DEALER! Thank You! :)
What size is the transaxle belt?
Have these bugs been fixed in the 2023 models?
Good instructional video but why don't you ever put in the part numbers?
Would be nice to show the belt path.....everything else in this video is self explanatory.
Where can I find this spring puller tool in this video?!?
I did this under a pivot (while running) without takin anything off. This is weird
I can't believe all of the negative comments! I've had my Ariens Ikon X52 for about six or seven years now. I used it one summer for a lawn business and have 2003.9 hours on it according to the hours meter.
Since buying the mower, I have only had to change this belt ONE TIME and came to this video because it just broke for the second time since I've owned it.
I have changed the deck belt about three times but that is a very easy process.
Love my Ariens mower!
Is your 7 years old machine exactly made as the 2019-2020 model??
@@simpleman7727 I don't know if it is or not. I know that often engineers try to make a great product better but end up with an inferior result.
Does anyone have a diagram how the belt goes on? You guys provide one for PTO belt
Shoe how to place belt on not I'm fast forward.
My Ikon XL has 100 hours on it and for some reason, i believe the belt tensioner pully is making a clunking sound every few seconds and I can see it moving side to side. Is it possible this needs to be tightened or something?
Thanks for asking! That tensioner pully isn't adjustable, so you shouldn't need to perform any service with it.
It's hard to guess what the issue might be, which is why we suggest contacting your nearest Ariens dealer for diagnosis. Our dealers are an extension of our team and will be able to help you to a resolution. If they determine the issue is the result of a manufacturing defect and your unit is still within the 3-year warranty period, the replacement parts and service would be covered.
Click here to find an Ariens servicing dealer in your area: www.ariens.com/en-us/dealer-locator
@@AriensChannel Thanks for the reply, I will check them out. I also checked my mower last night and could not reproduce the problem when I cold started it so I think maybe the mower belt just had a little slack in it that was causing the tensioner pully to bounce a little when it was warm. So it's possible I have no problem and that was just the pully doing its job. It was just weird because I would hear a little "thunk" every time that pulley was tugged but the mower seems fine now. I ordered an OEM belt to have on hand just in case mine goes bad.
Hi I have a 60" IKON XL and the pulling system is different, can you show me how it goes on? I have pictures if I can send them to you and we can speak more about this.
Thanks for asking, Todd. The hydraulic belt routing is actually identical on all Ikon XD-series models and should match this video.
Was it another system you were thinking of?
@@AriensChannel It was hard to see the belt routing when he put it on, maybe show THE ENTIRE BELT on after yall are done. But the video did help, she is p and running so THNK YOU!
Mines a DAY old 2hrs and do e slung the "drive belt" anyone have a diagram?????
We're sorry that happened to you, Jarred. The manual linked below is an older version of your unit, but the hydro belt routing illustration in figure 34 on page 26 applies to your unit: apache.ariens.com/manuals/05167900C_ENG.PDF
@@AriensChannel that’s not accurate information no where on there is an illustration of the drive belt…
I just bought th Ariens Ikon Xd52 …. Why does my drive belt keep popping!!! This is now my 3rd belt I’m replacing … the zero only has 41hrs on it … it’s getting frustrating… should I have gone with a John Deer !!
Did you figure anything out on this? I have only had my Ariens Ikon XD 52 for a few months and my drive belt just popped off too (after my PTO belt a month before it). Actually it seemed to "split" with an string coming out from inside it and getting tangled in the mower's mechanical components.
Pretty frustrating as a first time ZTR owner.
Common issue, I have replaced the hydro belt on a customers Ikon 52” 3 times this season. 2 OEM and 1 Kevlar reinforced
@@timothywagner403 I’ve slowed down tremendously and so far it’s been lasting… but shit takes forever now to cut cause I’m driving slow !!
@@bmfitzgerald3 I’ve slowed down on speed .. so far so good … hasn’t popped on me … guess it’s a poor design
@@bmfitzgerald3 also throttle 3/4 … not all the way
Quick question, why in the hell would you put a stop on the tension pulley on the direction i need to push it? What a joke of a design man.
26 hrs and mine broke wtf
Adding the washers will help for sure and use a Stens belt also 😊
My Ariens has 10 hours and stopped moving suddenly. I presume it's the Hydro belt. Very disappointed.
Hi Jeffrey, we're very sorry to hear about that. We can't say for certain what the issue is, but your nearest Ariens dealer will be able to diagnose the issue after a physical inspection of your unit.
Use our dealer locator tool to find an Ariens servicing dealer in your area: www.ariens.com/en-us/dealer-locator
These Ariens have been awful for me. No way I'm buying another one
We're very sorry to hear that. If you reply with some more details of your experience, we'd be happy to help guide you to a solution.
I agree Alyosha! I have a brand new machine with less than 17 hours. Nothing but problem after problem. Very first Ikon XD 60 had to be returned back to Lowes bc the PTO switch would not engage. This new unit keeps breaking drive belts.
@@jonathancobb1411 We're sorry to hear about your experience, Jonathan, and we'd like to guide you to a solution.
If you're experiencing these issues we strongly advise you to contact your nearest Ariens servicing dealer. Our independently owned and operated dealers are an extension of our team and will be able to diagnose and resolve the issues. Additionally, if your unit is still within the three-year warranty period, issues which are a result of a manufacturing defect are covered.
Use the dealer locator tool we linked here to find a dealer in your area: www.ariens.com/en-us/dealer-locator
They cut good. But fkn ridiculous bullshit always happening and horrible design flaws
@@AriensChannel "pay us more money and will fix what should have been right in the first place"
What size belt is this?!?!?!
Thanks for asking! This belt is Ariens part number 07200718, which can be purchased at your nearest Ariens dealer, or at our online parts store: www.ariens.com/en-us/parts/list?model=&serial=&search=&query=07200718
Thanks for sending me to the website that I’ve been on several times. And also for not answering my question. I clicked on the link and there were no matches found for that part number. This is the problem with companies such as ariens. I purchased a zero turn mower and I love it but when something goes wrong there is zero help. Sure look at all the cool attachments but can’t answer one simple question such as “what size belt is this?”
@@fancyfeathersfarm1447 Hi there, we're sorry that you couldn't access the product display page on our parts site. If you continue experiencing difficulty, try a different internet browser like Google Chrome.
As for that belt, its effective length is 56.8", its center distance is 21.9", its top width is 0.50", its angle is 34 degrees and its thickness is 0.31".
If you'd like more help finding the right belt for your unit, you can also reach out to your nearest Ariens dealer at the link below. We're always happy to help!
www.ariens.com/en-us/dealer-locator
Ariens , I did access the website but after entering the part number that you gave it said, sorry no matches were found. Still don’t know the size of the belt??????????????? My internet browser is not the problem. I just need a simple answer to a simple question. What size hydro drive belt goes on an ariens ikon x zero turn?
@@fancyfeathersfarm1447 Hi there. We're sorry for the frustration. Please email marketing@ariensco.com with your email address and phone number. We're going to have our RapidCare customer support team reach out to you personally.
Thank you.
Worst part of this is at 1:10
I can’t believe that they let this happen at the factory
That is so disgusting and upsetting to think they are that dumb 😮
Sorry I wasted my time, worst belt routing and idler alignment I've ever seen on any mower!!! And I've got 30 years experience 🤨
I guess I will have to remove the engine to change this belt. Mechanical engineers are such a waste of skin.
Looked at my ikon dx 60,makeing intermitent horrable noise,,240 HOURS the hydro idler pully,thanks aerens .your crap ant much in my.Wont do business w u ever again!!!! Cheapley made...
Yeah this has got to be the shittiest design.
The deck belt broke the one week later the drive belt broke and after watching this damn video it really makes me regret buying your machine.
Don't buy this mower!
WHY‼️???