Rust-Oleum turbo paint buff and wax! Must watch!
HTML-код
- Опубликовано: 28 авг 2024
- Hi, in this video I will show you how to make your $9 paint job look like a $200 paint job.
Here is the link of the video on how to paint it: • Turbo spray rustoleum
Products used:
Turbo Rust-Oleum Turbo Paint - amzn.to/3jZ9OJR
Menguiar's Ultimate Compound - amzn.to/37wrhmK
Menguiar's Cleaner Wax - amzn.to/3iAtmoc
Buffer Drill - amzn.to/2Xgk1K5
amzn.to/4c5R7O3
Nice job.
I had never painted a car or body parts in 30 years and at least 25 cars I've owned. This past week I painted my teenage son's Impreza in an open carport on gravel and dirt ground. I figured out what works for my area (western Colorado). I did 5 and 7 light to medium-wet coats on a whole car, over 4 sessions without fail. Apply and let dry for 15 (minimum) to 20 (maximum) minutes between coats and it works fine for the paints I used. You should spray two small test areas with all environmental/time factors the same before the actual project. For example, if you have an area to spray that takes 10 minutes to paint it, wait and warm-up/shake your next can(s) for 5 minutes and start the next coat. That's a total of 15 minutes. I know up to 20 minutes is also good. But 40 minutes was too long because that induced chemical reactions and severe wrinkling. I painted in the same order/pattern each time I sprayed a section. I had zero runs, spray errors, or reaction defects. The original paint condition was below average. No body rust, but 50% of clear coat was gone and hunter green was faded and rock chips galore.
Below is the weather, process and paint I used.
1. Up to 3-mph occasional breeze is okay, anything faster or constant is to be avoided. Clear skies, for light, preferred. 20% to 40% humidity. Temperature between 50F and 72F while spraying. Warmed spray cans in hot water in a bucket. Shake them as much as possible.
Paints used on sides, nose and rear (3 sections):
-- Rust-Oleum Painter's Touch Gloss Navy Blue 2X Paint + Primer: 1 medium-wet coat.
-- Rust-Oleum Stops Rust Enamel Gloss Navy Blue: 2 medium-wet coats.
-- Rust-Oleum Stops Rust Enamel Crystal Clear coat: 2 light coats + 2 medium-wet coats. I think a 5th coat could be applied with no problems.
Paints used on hood, roof and hatchback (1 section):
-- Rust-Oleum Painter's Touch Gloss Black 2X Paint + Primer: 2 coats.
-- Rust-Oleum Universal Hammered Black: 3 coats (4th coat optional). ***Color dries gloss dark grey with blackish specs, not solid black.
2. Sanded car with 100 and 150 grit dry paper by hand, with a scrubby dish sponge as the pad to fold the paper around. First, I sanded high defect/damaged spots...double their original size. Then I sanded vertically and again horizontally (cross hatched) the whole car.
3. From this point forward you must walk carefully to protect from dirt contamination...do not drag or scuff the ground. Wet the surrounding area to help keep dust out of air. Douse car with hot water and wipe down with rags. Let air dry 30 minutes. Check that all areas are smooth/scuffed well...touch up as needed. Wash with hot water+dish soap and rags/sponge. Rinse well. Dry with microfiber. Air dry 15 minutes. Tape up as necessary. 10 to 15 minutes before paint spraying use a microfiber cloth and lighter fluid or mineral spirits (same thing) to wipe down the section to be painted. Immediately before painting wipe all surface with a tack cloth. As you're spraying move slowly and don't scuff the ground.
4. Even in the open air you will want to use a painting respirator, but at minimum cover nose and mouth with thick damp cloth or N95/N100 face mask. Clear, tight fitting safety eye glasses work best...the larger goggles reflect light and make wet paint difficult to see clearly. I had to go without eye cover and just squinted my eyes when the paint spray was thick, because goggles distorted the light.
5. It will take these paint formulas 3+ hours to dry to firm finger touch so leave it alone for 5 hours. I let it dry 24 hours in the carport and then put it in the Sunlight for 2 more days before driving. At 25 to 30 days I'll polish and wax it.
If you want to see pics drop me your email and I'll send you a couple.
That was awesome, talk about a mirror image. I’m doing this to my wife’s Durango. Just picked up 5 Turbo cans of Gloss White. Later this Fall I’m painting my truck with the Turbo Black. You did a great job Sir.
Thanks boss
I have to say for a rattle can paint job it looks pretty dam good!!! Here are a couple of tips for you. Before you do any bodywork you should wash the vehicle laundry detergent works very well and get edges underneath. You used the green primer that is what we call an e coat primer to seal the metal you should have put a primer surfacer then sanded if you needed to, also get one of those wet sanding sponges so you don't get the finger lines as you sand and put a couple of drops of ivory liquid dish soap in the water it helps with smoother sanding. The biggest thing never ever wax a fresh paint job!!!!!! Wax doesn't make the paint shine buffing makes the HIGH GLOSS the wax is what protects the shine that you just created... get rid of that buffer you need one that you can feather the switch if your afraid of burning the edges put some of the blue painters tape on the edges to help you from burning... Hope this helped you..... Not judging just want to make all cars shiny...Good luck
Wow thanks for taking your time for the tips , next video will be better 🙏👍😁💪
Quality comment. Not because what you said was accurate, but because you’re being a genuinely nice person who’s sharing tips/info to help someone.
@@sideneiluiz8236
I'm curious on what inaccuracies about the tips I've given? I have been been doing, learning and teaching others for 40 yrs..
Ok thanks
I really enjoyed the video , but I will follow your recommendations , they are clears and easy to follow . Thanks many Times . 😀👍
I do see ripples on the whole hood but due to hand sanding vs. Block, but the results came out awsome regardless. Not bad for budget job.👍
👍✅
I was going to recommend block or atleast pad sanding in a cross hatch pattern to level the flatter areas. Beautiful work and keep being creative.
Thanks yes next paint job I will do better lol
If you are going to sand with your hand you want to hold it with thumb and lower pointer finger and fold it in 1/3 and use your palm to sand. Get those fingers off the paper.
Thanks yes next video I will try it
That my friend, is a Sweet Heart of a JOB!!! YEAH!!! I am doing my wife's entire Toyota Matrix in Black!
I cant believe that came out of a spray can. Good job Sir!
Thanks boss
Came out decent but would highly recommend using a sanding block to get the paint flat and even before buffing. Can't wait to see rest of car good job man
Thanks boss will do
Lol. He mentioned this in the video. Wow
Automotive Spray paint in a can is STILL paint; follow the procedure,(patience included😉) you'll get the results! GREAT JOB!!!!
Be carefully bro I bet every paint shop is getting together right now plotting to get ya 🤣
Outstanding job I will be trying this very soon before they catch us out 😂
👀🤣🤣🤣🤣🤣✅ sure go for it
Holy crap that actually looks really good
Thanks boss still does
Looks fantastic! This is how smart people save $!!! FYI- After you paint the whole van just be careful when pumping gas, it has a tendency to eat through or stain the rustoleum.
Hey thanks boss ,, yes I know so what I'm thinking is adding 2K clear at the gas area or maybe I just clear coat the full van ,, I did the new front pumper I will post it tonight
I’m in the process in doing two sides to my Mercedes sprinter van I think I’ll start job after watching this great job and awesome video 👍🏼
Thanks boss go for it , also if you add 2K clear it will be just like factory paint
This gives me confidence in my car! Awesome job man. Thanks for this.
You're welcome boss thanks for your feedback
You should definitely wet sand with the backing pad so you have even and consistent pressure.
No circular motions, either.
Yes sir I will make another video soon , I will correct all the little mistake on a new hood this time with 2K clear , thanks for your tips
Waiting for you to put out a video
Ok thanks
@@nestorautorepair I was calling out Joseph Migliore. You did a great job man. Can't complain
@@aarongrisham5555 What would you like to see??
I just painted the front end of my car with this and was suprised honestly how well it worked BUT now seeing this I am going to go back and paint the whole car and then wetsand and buff it!
Men I wish I had time to do my van lol good let me know how it comes out
Nestor Auto Repair painting the rest of the car this weekend. I’ll send you the results
Sure thanks let me know how it comes out
@@Bradvision how did it turn out? I want to do my Volkswagen the same way
Well still holding like day 1
Very nice, it's hard to believe it came out of a spray can thanks for sharing.
Yes sir thanks
Why when spray guns are new compered to paint jobs rollers was used back in the day good paint is good paint it can be applied in many ways guns just make it more efficient but you get the same results from can I did my 2006 Ford fusion it came out awesome nobody could believe it even though I did it outside right on my street and people are amazed now asking me how much would I charge to do there's
Very nice job! This is so exciting! I'm picturing my lawn tractor, my tiller, my trailer, and my metal kitchen cabinets all looking like a million bucks!
Thank you for posting this video.
Oh wow thanks John
That’s unbelievable, looks damn good. People will say it’s not as good as Factory. I say that is really good right out of the spray can and a buff. 👍🏼✌🏼🇺🇸
Thanks boss I will do an update soon still looks good
@@nestorautorepair awesome, looking forward to see the result. Good luck and we’ll done. 👍🏼✌🏼🇺🇸
Thanks my boss will do
It came out great, I have an old suburban with awful paint I wanted to hit it with tractor heavy duty Rust-Oleum paint, 😏😏 buffed it'll look factory, now to the second scenario of if black or white color, I like the white with black tints but I also did the black on black look
Love it. Been prepping an old trailer. you sold me . I'm ready.
Good!!
I wish u were my neighbor this way I could do my 96 civic dx coupe, it needs paint bad, you could handle it 4 sure, great video and talent!
Thanks boss
Can’t beat that look. Nice work. Use a sanding block for the paper next time. Your job will look smoother next time. 🤘
Thanks will do
My man! You got skillzzzz. I bought that paint for my daughter’s accord. Now you raised the bar what it should look like. Damn. Ps; a guy like you needs a compressor. Please look into Fortress line at Harbor freight. Super quiet, dependable. Had mine awhile. Love it.
Oh nice thanks I will look into it , thanks for your feedback
Looks great for a rattle can paint job! Great for people on a budget or without the equipment to do it the conventional way.
Yes sir thanks
This is AMAZING! so I could do this to my whole car if I wanted to? This is crazy good !
Yes sir you can
@@mike-le2xp eh was gonna do it on an old Chrysler I had so scratches won’t bother me but thanks for the info good to know!! So did u see the other video he had of the hood. Is it connected to this one??
Thanks I think I will at some point add clear yes but I hope it hold , because it been so long
Looks great! With some elbow grease and effort looks amazing! Obviously he has skill in this stuff but damn looks good especially without a compressor
Thank you sir , thanks for your feedback 💪💪
Good job my friend beautiful!
Thanks
I'm learning you did an Amazing job. My first time painting with spray paint. This is Awesome really learned alot. Thanks for the Videos...Totally Subscribed 100%%🙂
Thanks boss 💪
Amazing finish. Top job fella, I'd be happy with that. 👍
Thanks 💪
Looks really good brother. For what you used you can’t beat the results.
Keep it up
Wow, it looks great! It looks like a mirror.
Turned out really nice. Meguire's is some awesome stuff. Take it a step further and put some ceramic on it. Turtle Wax makes 1 called Hybrid Solutions. It's one of the best. Only $17 a bottle. Others are $30+ for less.
Yes sir thanks Chad
Thank you $10.00 paint job Awesome !!
You're welcome , thanks
Great video man, one tip though, NEVER use a brush to wash your car, you're going to eventually scratch the paint or leave scratch marks
Also don't do circles when you're doing any kind of sanding whether it be wet or dry sanding, you can create swirl marks in the paint, use a cross hatch pattern to sand (X motion) that also makes sure you get rid of the sanding scratches from the last more abrasive grit
Got it thanks
Ok boss thanks for your tips next time
I'm this case it didn't matter cause he wet sanded and polished it after anyways but yeah avoid brushes man
👍
You should be using a rubber block to wet sand. Also should be sanding in an X pattern instead of circular. But you know what? This does look pretty good. Good job man.
Thanks will do next time xxx
@@nestorautorepair its whatever you like but an X does work to help keep your surface true.
Ok thanks
Ditch the meguiars compound with the right products you will get that level of shine before the wax coat, also handy trick few drops of dish soap in the water helps when wet sanding
Thanks for sharing boss
Nice rattle can job! The can't wait to see the rest of it when it's finished!
Yes thanks boss me too
I shoot quite a bit of rustoleum, but use gun, hardener, Japan drier, fisheye retardant, a lot of Acetone, , get it thin enough to to flow well, and recoat as recommended. Mine usually is fingernail hard in an hour.
Thanks for the tips
Wow looks amazing ! Great job ! Now i know what to do . Thanks ! 😊
Thanks boss
You did an awesome job
That's impressive 👍. Keep in mind there isn't much UV protectant in spray bomb. It will probably look like a chalk board in 6 months to a year.
Ohhh wait for it is coming tonight update on the video it been 9 months
Wow man great job. My project Ford 500 needs something like this and I’m going to try doing this thanks for the inspiration
Yes sir you welcome , thanks for your feedback
Hey Carnal how does the Paint hold up? Does it flake off or fade ? I want to paint my Camper shell with the same paint... thanks for sharing this video
After a year it fade a bit or I will say it was not the same shine so what I did I add 2 k clear and hood still the same shine
Cool thanks 👍
the result is amazing
Thanks Ramez
Youre a lot better at that than me! I dont trust my hands to sand evenly. I use a foam block or sponge. Some people can use their hands because they can feel it better. Looks great man, Thanks for this video.
Your welcome, thanks for your feedback boss
you know very well polishing tricks, just i think you my used 600 grip sand paper , before 1500 , .. because you got some orange Peel in the corners. but for spray paint job, you own my respect
Thanks boss I will give a try thanks for sharing boss
Welp, looks like I'm gonna paint my truck now lol
Go for it
Outstanding job! I LOVE IT!
Thanks boss
Hell yeah I like it. Looks good. I would’ve done a clear coat. Here in Texas that paint won’t last a year without a good clear coat
Thanks boss
You're wrong. If the paint does eventually get oxidized, he can buff it out easily. Once your clear goes, it has to be redone.
Ok
@@zachary3777 Clear last longer and protect better that single stage paint. If the clear is gone, single stage paint would have been gone long before that. You also buff and wax clear.
I always say you can have an amazing paint job with rattle cans if you do the same steps and preparation you would do with a normal paint job.
Should have wet sanded more. Still see orange peel. Really good considering it came from a spray can though. Nice job!
Sure thanks
My detailer side came out when i saw that brush he was washing with, then i remembered hes sanding anyway lol but use a sanding block(or even a sponge) so your sanding comes out right. And dont do circles do a cross hatch
Lmao thanks boss,, next one I will do better thanks for sharing your tips
wet sand with a pad. cross pattern (front to back, then also side to side) no circles.
Yeah sure next time thanks
Going to be doing my 2006 Kia Spectra in that black very soon. Hope it turns out like your hood my man. Awesome job, hope you do some more.
Yes sir thanks for your feedback , I will make some more soon
How did it turn out?
Still good
Looks good
Thanks, boss, for your feedback
That came out really good man
Thanks Chris
Wow that came out great brother! Especially without a clear. I'm going to follow your steps if I mess up vinyl wrapping the hood.
Lol thanks boss yes nothing too loss well time and lest then $10,, best luck
@@nestorautorepair Well ripped the vinyl wrap today. Might have to paint it now lol. If I wanted to shoot a 2k clear over this how long would you wait after the paint has been applied? And how would you prep it?
I think is best if you add the clear one hour after you apply the paint because this paint take longer time to dry compare to other rattle paint ,, 2k clear don't work with every pain some of them will have a reaction like fish skin , so please when you paint the hood pain something else so you can do the test with the 2k clear before you add it to your hood. but I'm sure it will work with this one , please let me know how it comes out
@@nestorautorepair ahh thanks for the heads up. I think I will just spray and then buff and polish when paint is fully cured.
No problem
Great results with a rattle can. A palm sander and 600/1500/3000 grit would flatten down that orange peel and bring out more shine.
Thanks John , I will try that next time
That looks good as hell
Thanks boss
That's whats Up! Great video bro👍👍
Thanks Christian
Very impressive Nestor 💯 great job maestro 🤑
Thanks philip 😁✅
Nice work bro looks really good especially being spray paint
Thanks Jae yes I like it I will make an update soon
I have seen body shops do panels like this NEVER look this good for hundreds of dollars....
Thanks yes this cone out good
Lol. That polishing pad is owning a few years to the graveyard
I love it!! Thanks for sharing.
You're welcome boss , thanks for your feedback
Not criticizing, just passing along some tips. Be careful when you’re buffing sharp edges or edges of panels. Noticed you had the buffer turned the wrong way on the front side of the hood, always let the buffer roll off of any edges to help reduce the chances of burning through or it catching and messing up your work
Sure thanks for sharing boss
After the compound you should have used a polish then wax to seal it. Not knocking your work but you should always follow up with a polish after compound. The finish absolutely comes out better.
Will do next time van still here lol same as new
How long did you wait after painting til you wet sanded? I just painted my fender and wanted to know its curing time. Thanks for posting this video!
2 weeks
The pad you use to sand is so you dont sand finger grooves into the paint. It will make the paint flatter.
And you need to start with 600 or 800 then work your way up to 1500. That 1500 did nothing for your paint job.
Ok
Ok
Sound like you are too good to be watching this type of video ,, well 1500 work for me but thanks for sharing
@@reverendroger2221 6-800 on a turbo can is probably going to go through. What he did came out good.
Damn that looks incredible.
Thanks bro
Looks badass, just subscribed
Thanks Don thanks for your sub and your feedback
Wow great job Botha
Thanks boss
Good job good teacher 👏
Thanks boss
Nice work!!👍👍👍👍👍
Thanks boss
Wow it looks very good. Was this only with the black paint or does it also have a clear coat?
Thanks this was jus2t the black pair , I did add 2 clear after 1 year and hood still the same
Nestor, you are amazing!
Oh thanks ,, thanks for your feedback
Lol a body shop would have charged 5000 dollar's to do that job .....
Very impressive !
Thanks
Damn, this looks really good. I am planning to paint my whole car with the Turbo paint as well, so I'm just taking tips and tricks to do it
Yes sir that's my plan as well ,, just don't have the time to do it been so busy , but one of this day I will make it happens ,, good luck on your project
@@nestorautorepair thanks man........I have to wait for the perfect time to do it, cause with the most of the world trying to get back on their feet, so am I trying to, I'm unemployed atm so got to get a job first and get the supplies first
Got it ,, your welcome good luck on the job hunting
5Star Empire instagram.com/ej1_h2b just did my car white today with turbo paint 🙏🏻
@@Scooter_built ok kool, just saw it, impressively good
Very well done Sir
Thanks Daniel
Great work
A lot of orange peel but it does shine and for a can paint job it's nice
Yes sir
Don't get me wrong I definitely think you did a good job. From what i seen Orange peel even for automakers are hard to avoid.
Yes sir thanks for your feedback
Awesome job! Looks gorgeous!
Thanks Steve
Won't hold up in hot summer days
Well still holding let's see how long it last
Very informative video, thanks.
Thanks Dorantes, thanks for your feedback
Use a flexible pad with the sandpaper to wet sand for a more uniform job. Finger pressure creates inaccuracies.
Yes sir next video coming soon will be good
@@nestorautorepair 100% Rustoleum Job here. ruclips.net/video/6Pr0YrRzX28/видео.html
Nice video
@@nestorautorepair Thanks, Dude !
Nice effort...
Add some soap to your wet sand, it floats the paint off the paper and keeps it from clogging. Paper ain't cheap, this makes it last. And easier to sand. I like dish soap, but your car wash soap will do fine.
Thanks will do next time
I painted my toolbox with gloss black 50 percent more spray and I had to do it in my backyard in the evening when the nats are out and I got some nats in the paint, can I wet sand the paint before I clear coat it or just leave the imperfections in the paint and clear coat it and wet sand the clear coat.
Hi yes you can wet sand it after 2 days and clear coat it
Wonder how it holds up to any spilled solvents? Gas , brake clean etc. but yeah, for the price you can’t go wrong! 👌
With the 2K clear will be good to anything , but as now with no clear I'm sure gas will take it off
Good Shit Bro, thanks for posting...
You welcome Paul
Really good job. But without clear coat I’m assuming the paint will start to fade quickly since there is no protection against UV rays. Super great job none the less.
Thanks boss I just add 2k clear a year later and I need to buff it out and make a video soon
@@nestorautorepair
Thanks. Your video just inspired me to do my old truck. And once again. Great job. God bless.
You're welcome boss , thanks for your feedback , I hope you do a good job on your truck
Wait I’m confused I thought this was going to show you how to ping the car, so this is after you use the rust oleum paint can?
Yes sir I do have a link under this video oh how I got to this
Thank You !!
You're welcome
ITS SHINY BUT VERY WAVY. IT IS NOT REFLECTING SHARP SYTRAIGHT LINES. TRY A LOWER BUFF SPEED SO YOU'RE NOT WARPING THE PAINT AND CLEAR COAT.
Eso se ve como espejo 🔥💯
Gracias brother , pronto pondre un Nuevo video de como ba estar con 2kclear
That looks great
Thanks moonchild
Actually for sanding you want to do x patterns especially on black cause the swirls show
Sure next video thanks
Kool it looks really good my question is what is the dry time before sanding with 1500 grit? Bueno sir I'll stand by 4 your answer again awesome work sir RF from Tejas
1 week boss then you good
Tip..use that same polish on those headlights with that buffer wheel. You will have new shiny headlights. Then put the wax on the headlights to protect them from the sun. Your welcome
Lol thanks I did after I was done that's exactly what I did and yes they come out new ,, thanks any way boss good looking out , good ocervationg
Looks awesome 👏
Thanks boss
Looks great. Fantastic job. Are you concerned at all with the methanol in the windshield washer fluid eating away at the finish?
No really but let's see what happens thanks for sharing
Front,, back - side to side would be the same. Think it's up and down or side to side