How to Bend LED Strips Around Corners
HTML-код
- Опубликовано: 7 июн 2024
- James with Super Bright LEDs shows you a quick and easy way to get your LED strip lights to round corners and make turns with a few simple folds.
Check out our full selection of LED strip lights - bit.ly/3EQMado
Check out our LED strip light connectors - bit.ly/40gvlBH
Need you cut your strip? James shows you the right way to cut your LED strip light • How to Cut LED Strips
Need to connect your strip? James shows you how to solder a connection • How to Solder LED Stri... and how to use solderless connectors • How to Use Solderless ...
Super Bright LEDs is your #1 source for high-quality LED lighting for everything. Browse the web's largest selection of LED strip lights and bars, LED lights for vehicles, landscapes, and much more.
Website: www.superbrightleds.com
Facebook: / superbrightleds
Instagram: / superbrightleds
LinkedIn: / super-bright-leds - Авто/Мото
Worked with my Govee led strips
Excellent thanks
Thanks for the video!
Thank you very much
The folding method by far seems the cleanest but do you think that those folds could potentially cause enough heat to damage the strips in the long run??
Great question. It depends on the strip. Most single-row strips will be fine, like the one used in this video. However, for high-density strips or double/trip/quad-row strips, we would not recommend this method.
Thnx man love from India love you
Can i connect this with electric switch board or not
Hello, is there a way to turn an LED strip 180 degrees to run it back along itself?
I went to light international exhibitions and find strip led light which works with 220 ac no DC adaptor improved any other electrical unit required , it helps me to work more accurately, with the help of cable tie, I attached to the light Aluminum pipe , noticed the pipe is vibrating a little bit when I move my finger along with pipe.
Ive always used the folded 90° option on indoor strips, I've never had one fail yet. This doenst work on the thicker oitdoor siliconed strips obviously...
Remove a small part of the silicone for the fold(s) then re-seal with a glue gun.
What about the led COB strip? i need a 45 degree fold turn as well for a seemless look
You can definitely do the fold on COB strips. Just take it easy when folding it. Of course, we'd still recommend a solderless connector because they're only a couple bucks and look even more professional.
Question. Will the L connector work with Phillips hue strip lights ?
Short answer: probably. Our L connectors are designed with our strip lights in mind, but as long as you match up both the size of the strip along with the type (e.g., Single Color, RGB, RGBW, Tunable White, etc), you should be good.
Y this worked well
So a strip led won't break if you double it? I am afraid that it might break that why I don't do it. Never knew it was that flexible. Thx
How did it go?
It went great. I could easily do 90 degrees corners to each direction. I was surprised they didn't break. I just tried to double them where no chips or LEDs are present. I tried first without removing the tape, then when I got the trick it was easy. So yes no problems for me. My LEDs were from AliExpress from a company called RGB. Very good quality.
I tried the folding and now my led strip doesnt work anymore from that part😂 will have to use the cut method instead
Noooo! Sorry to hear. Yes, when in doubt, use the solderless connectors. They are very inexpensive, easy to install, and look better than any of the bending/folding methods.
Happened to me on RGB strip, after every bend, one of the colors stopped working :D
how to repair the charging system🎉
Use connectors
is there a technique to fold led strips 180 degrees to go over a spot again?
Don't try this on cheap strips or it will break.
too late 😢
You are correct,the pcb is thin and flimsy which can be hardly fixed good by the connctot.
I did the folding thing and now the Green light don’t work💀
Same now only my green one worked
try to not bend led as this will create hotspots. basically asking for something to go bad.
just buy connectors
Folding strip is not ok, conectors leave you with blank space... Buy soldering iron and just solder them if you need to go around corner
Dont cut your rgbci strip otherwise you gonna end with a mess
No b nn m
Up to 60 cigarettes a day?!? No wonder he died so young.