Removing and Installing Crank and Bearings - Yamaha YZ 250
HTML-код
- Опубликовано: 11 июн 2018
- Support us by grabbing your parts and accessories from AOMC.MX!
aomc.idevaffiliate.com/100.html
Thanks for checking out my video! Please subscribe, like, or comment, and check out our gear below!
Also, check out our other channel / rtipowersports
My gear!
Action Cams
GoPro Hero 5 Black
Primary GoPro Action Cam : amzn.to/2ADAJ6M
Waterproof Housing : amzn.to/2B0Xt3n
Mount Kit : amzn.to/2kx6YAA
Battery / Charging Kit : amzn.to/2B6HY6x
Yi Lite Action Cam
Secondary Action Cam Yi Lite : amzn.to/2kvHjYW
Yi Cam WaterProof Case : amzn.to/2kvbn7a
Selfie Stick / Tripod : amzn.to/2AWnfpp
Handheld Gimbal Stabilizer : amzn.to/2BJbord
Drone
Primary Drone DJI Mavic Pro : amzn.to/2AXNXxB
Mavic Pro Battery Multi-Charger: amzn.to/2BDn3Jk
SD Cards : amzn.to/2DcU3Zn
Vlogging
Vlogging Cam : amzn.to/2Covk48
Vlogging Mic : amzn.to/2CmzRnH
Vlogging Camera Adaptor: amzn.to/2zN3N9L 
Авто/Мото
Due to risk of damage, myself wouldn't install the crank seals until the crank was pressed in and the cases mated.
That's a really good point and great idea. I'm just so used to my kawis which have to be installed from the inside , so I always do them early. Thanks for the tip!
@@mxgryan hey I got a question how do I remove the seals on my kx85 crank with the bearings in? Do I tap it all out from the outside in?
@@johnniereyes643 send me a photo on FB
How long do you recommend freezing the bearings for and do you freeze the crank ??
Hammering the crank into its bearings will ruin the cranks true!!
Thanks for watching Andy!
I'm sure a little tap with a nylon hammer will do no harm....
Did you freeze the Crank?
that's the difference between pros and amateurs. also there's alot better ways to install a seal than at 5:10 or so. your engine is always treated better than this at our shop guaranteed.
Beating on that crank isn't doing you any favors. You can knock one out of true in two ways.
ruclips.net/video/SSsUG25ehc0/видео.html
Got another question the bearing oil seal do you pack any kind of grease in them?
I never have, no. I do lightly coal the seal on the inside and outside edges before install, but thats been it.
About how long did the whole process take? Like taking everything off and back together
A decently experienced mechanic with no distractions could do this in a half day.
If you're a normal guy that doesn't do it often taking your time, set aside a weekend for good measure.
The MX Guru ok I’m building an 85
Hi I’m rebuilding a yz250, I replaced the bearings along with the bearing cap/seals and the crank as well. When I went to put the casing back together, it didn’t want to fully seet down. I ended up getting it about a quarter inch away from being fully flush but it won’t go the rest of the way down. When i tried putting a few screws in the block and lightly torquing them down to see if it would help, it caused the crank to freeze up and also made no difference in the gap in the block. Any ideas?
The cases should not be bolted to close, that will cause tension in the crankcase and everything will freeze up, make sure the cases fully seat before torque is applied by bolts
Whats the red stuff you were putting on the bearings and when putting in the seals?
Maxima assembly lube!
www.ktm-parts.com/78-9970.html
About how long do you heat up the case when you put the bearings in?
Maybe 30 seconds to 1 minute it about all you need with a map gas torch. If not, keep heating!
Thanks for the info this is my first time attepting this lol im guessing you had the bearings in the freezer or something? And was the crank frozen too?
I like one minute with regular propane. MAP is nice, but most only have a propane set up. You want to get the area about 250-300 F. Lick your finger and quickly touch the area. When it sizzles you're probably good.
Are you freezing the bearings and walking the casing?
I have no idea what walking is
How do you take the bearings out?
Heat and gently tap, or heat and gently press
When you dropped crankshaft into the right main crank bearing was there a little side to side place when fully seated ??
Was there a little bit of side to side play when you filled seated that crank into that bearing?
Not that I remember...but this has been years lol
wow a claw hammer?! and you junked the seal out by prying it up with a screw driver after you drove it in crooked!!!!!!!!!! I guess your shop shoes tell the story..........
Dude I LOVE that you liked the video, and I appreciate the watch time! A few more bucks in my pocket! Rock on!
Was that a claw or a rip hammer?
Doesnt matter, they both do the job fantastically!
Any videos on how to install the transmission?
ruclips.net/video/wY5LJPJqci4/видео.html
ruclips.net/video/g9V6l1olNNg/видео.html
hey man can i let the clutch in i just need to reseal the case ,
No sir.
@@mxgryan well that sucks i need to pull it apart the bike is brand new but the dealer wont fix it because its pass the 30 days
@@AdrenalineRushMX bummer man! Go KTM next time haha
@@mxgryan i never had prob whit older yz250 i ride yz 250 since 1998 xd
Takes alot more than that to hurt a bearing. As long as youbdont bash the living shit out of the boss part "the middle" its fine.
Agreed, if the tapping is on the outer race or both, its usually okay. Additionally, I'm not hitting that hard but the audio from the video makes it seem that way. This bike still runs.
your not fitting my mains!! far to BRUTAL !!!
I'm definitely not fitting your mains. You cant even afford this reply, much less my hourly rate buddy. ;)
Sorry to say but your being pretty harsh on fitting the bearings !how long you Been building engines for?
This one is still running great to this day, thanks for asking Keith!
Can you re build my yz80 for free please I got ripped off I bought it for 1400
Lol
Wtf. This is pure chaos
Thanks so much for the support dude!
@@mxgryan i dont think he was being suportive
@@hugolundmark5947 Thanks for everything Hugo!
Everyone’ thinks they no a better way but forgot they are watching a how to video
Savage😂
The title needs changed to how NOT to install crank bearings, seals and crankshaft. My God this was painful to watch.
This bike still runs flawlessly, thanks for asking, and thanks for your positivity Mr Ovalhead!
@@mxgryan Anytime lol
Yes😂😅