Connecting rod and bearings Replacement in crankshaft. (Easy way)
HTML-код
- Опубликовано: 25 авг 2024
- Easy way to repair connecting rod bad noise and bearing's fitting and balancing.
if you like then please subscribe to my channel ☺️
⚡Zimbiker⚡
• Must watch
Wait is over guys.
Tool making video ruclips.net/video/ak6JhyfcCv0/видео.htmlfeature=shared
its so gentle work, you respect the crankshaft ❤
I made the same jig 10 years ago. Glad you think the same
Where are you from?
@@Zimbiker new zealand
Nice to hear.
@@Zimbiker thelaganastate, india
Kya bhaiya behan balance rotor myecoenergy kaisa aate begin ka balance toll Mai Ko Na ji
Really smart jig for lining the webs up for pressing. Might make one of those when it's time to do my crank.
Same
Love the cammed holding jig. Nice work
🙏🏻👍🏻🙏🏻
बहुत अच्छा काम किया है, ये टुल बहुत कम लोगों के पास होगा।
Shukriya ❤️
That thing is smart. But, if you press bearings into the crankshafts and hammer gears etc into them, you now have to re-true them.
Мастер,побольше бы таких людей
Decent work,.. Nice👍,.. Love it!!
Apka shukrya 💕
The insertion of bearings at the end could have folded the rod pin best to use support below individual crank webs rather than the whole crank
is it possible before installation of rod bearings are inserted
Mantap bosskurr special tools therbaiek laa.. senang kerja Dan cepat.. great idea.. semoga maju Jaya hendaknya 👍👍👍👍👍👍👍
آپکا شکریہ ❤️
You make It so easy
Thank you 💖
Hello,should i buy new connection rods for an outboard engine everytime i do a engine rebuild?,the engine is a Suzuki DT 25 2 Stroke outboard from 1987.Or should i install the same connecting rods?They are almost 40 years old...i use the boat 2 or 3 months per year.
CNG, Caren 🇧🇩
Sir, the figure shown, I hope
you understood it.
1) heat prob.
2) in newly_built piston , air escaping from joint may not reach to top of the piston.
3) piston is to be replaced often.
4) cost.
5) as the time goes joint hole
will be widen. It is major problem.where as in scroll it's not.
واقعا دمت گرم داداش
Brother ilove ur work
Apka shukrya 💕
That is one smart idea for a jig Bro , Awesome bit of kit 😁😁🤘🤘
Thanks 👍
Thanks for the helpful video!!!!!!!
😊❤️
Very good job
Properly karigar o tusi very good toll
شکریہ ٹواڈا❤️
dengan jarum ukur lebih tepat 👍
U r reyal makenic brother
Mashalla baei jaan
Presisi and clean
Excellent video brother 🙂👏
Very nice video brother 👏
Very good video brother
Awesome jig
😮 o top 👍
U r Soo good brother 👏
Yes i like..🤩
Thanks 👍
Hi sir is it possible to replace cbr 250r connecting rod
Nice 👍 video brother 🙂
sir kmaal ka kaam ha
apki shop kaha pr ha complete adress
Nice work sir, excellent.
Thanks
Congratulations 👏👏👏👏👏👏
Good job.nice
THANK You 💖
Good❤
🥰
How do you line the
Crank halves up?
Thanks for watching please watch again carefully.
@@Zimbiker i
Did watch. 2wice.
Make third try hope you got it 😂
1:56 he has a jig for it.
Couple coffee can lids, a toothpick, a little luck and a whole lotta whisky.
Good😊❤
Thanks ❤️
Great work. Can you give me info about your tools. I need that setup.
I was thinking the same thing. That’s a sweet press set up.
Tool making video ruclips.net/video/ak6JhyfcCv0/видео.htmlfeature=shared
Auto mech here. I never realized that this is the way small engine crank& rod was held together and balanced. Might be stupid question but what keeps crank and rod from becoming unbalanced while operating? Jus press fit? Yikes.
Nice job!
Thanks!
Total price for this repair
PERFECT!!!!
Excellent 👍 👍👍👍
Thank you 👍
Still looking for an answer after 40 years. In motorcycle magazines in the 1980s. Performance shops would "weld the crankshafts" of Kawasakis and Suzukis. Their flagship KZ1100s and GS1100s had assembled crankshafts with roller bearings. Welding made them as strong as one-piece cranks from Honda and Yamaha. How the hell does someone get a weld into the deepest reaches of a crankshaft to make it one-piece??
I have yamaha atv breeze 125. the crankshaft looks the same. The craft man instaled the spoket wrong so the timing was not corrct. It took me by myself many experionces after destroying 3 sproket I coud after heating and pounching to bring it to accurate place. How did you know the plave to instaled it. the marking.
We checked it and than fit 😂
15,20 daily average rods fitting in Crankshafts sprocket timing 100% accurate. No problem dear grow up.
Why you destroy 3 sprockets?
Did you not checked it's before?
@@Zimbiker ruclips.net/user/shorts0raOB6ynSaM.. I assembly the cranck to engine but not the craft man that assemblt the rod.
@@Zimbiker I hit the sprocket with torch and punch with hammer.
Astagfirullah.!
Don't do that works which you don't know.
Go to machinist.
@@Zimbiker you supid mechanic. I said the mechanic made a mistake i fixed it.
Do I need to do any of that if I buy an all in one set?
Tool making video ruclips.net/video/ak6JhyfcCv0/видео.htmlfeature=shared
Super nice video.....
آپکا شکریہ ❤️
Zaberdast
Shukriya ❤️
Hi , how many tons is your press ? A 10 tons press could do the work ?
I have 16 tons press that works smoothly.
@@Zimbiker thanks.
Would love to send you my crankshaft assembly for this same work
Very good
THANK you 💖
Super
Very nice
Thanks
Crank line karne wala jugaad kahan se milega
EFFING MINT !!!!!!!!!!!!
Can this be done with a raptor 700r crank and rod
ناممکن نہیں
how can I buy a centering device like the one in the video?
Masters of engineering
Lokasi mana om
My karizma complete 15 year still now engine never open... but now connecting rod must to change... Witch number connecting rod replace for karizma?
You dont need number. Go on Repair part shopping. You say, I need karizma Connecting rod.
Brother how to make this jig plse make a video
Where can I find a jig like this?
Make it yourself
👍👍👍.
Hola amigo necesito el kit ese me pasas el cont quién lo vende gracias
Self Made item
Can you buy a crank jig like that?
AP k Kam ka tareka belkul the k hai baring lagane ka tareka the k hai press sey is ki madad sey goleya kharab nahe how ti
Can we use cylindrical roller bearing NU 304 instead of ball bearing 6304?? Both are of same dimension. Will it increase the life of crankshaft??
Nope
@@Zimbiker Laga nhi sakte ya life increase nhi karega?
Location po
bhai ap ki shop kaha ha
ap kis city sa ho
Easy if you have the right tool...🤦🏼
Yea ikr. I try to do most repair myself but whenever something like this come up or anything suspension related I just give it to the mechanic
Just a thought but maybe you could freeze the part the rod sits on and use a torch on the crank weight to get it to fit
Amount yenta price of work
कहाँ होता है भाई ऐसा काम जगह का नाम बताई
Sir Gudmurning Yung huli Ng press mo sir Yung tbi Ng bearing Parang sprocket my sinusundan b n mark. Sana my makabasa
SA skygo 150 yun
Available connecting rod xt250, how much
Coloco a biela pra o eixo nao encaixar torto
Sabhi khardiye app ka jesa kaam kar ne lage to engine jaldi re open na ho or machnic badna na hon
Haa g
Is kam me total kitne paise lagta hai
kos berapa bos
👏👌👍
Shop kdhr ha Karachi
Shop kaha hai
SM MOTOR
🙏🙏👍👍👍😀❤️
💖💖
🙂👍
👍👍🏻
Demir altın oldu kurfarkınla ekonomi
Serviço com controle
👍👍👍❤❤
❤️❤️❤️
Bhai apna adras dalo
कहां पर मिलेगा
Ye tool kaha milegi muchje bhi lena hai
Khud banaya hai. me kal is ki video daal raha hoo deakh lena.
Mere liye 1 pic bna dijiye jo cost aayega de dunga
Bro mery channel pe iski full video hai aap voh deakh ke khud bi bana skty ho agar aap Lathe machine ka kaam jaanty ho.
My WhatsApp
03269510025
My WhatsApp
03412302069
Online patlrcel receive Ker k advance payment per kam Ker daty hai. Aap
Ye kam kaha hota h Crank ka bro
Brother aap Ajao mery paas Pakistan fsd city
Size of bearing?
6304
make a tutorial how to make the tool
Good idea 😉
Please make a tool like you used at minute 1.55
App ki shop kon sa shehar ma ha
آپ کس شہر کے ھیں ؟
Karachi sa
Who keeps honking
ВОТ ПОЭТОМУ У НЕГО ВСЕ КОЛЕНВАЛЫ КРИВЫЕ . ПОТОМУ ЧТО ПРАВИТЬ КОЛЕНВАЛ НУЖНО ПОСЛЕ ЗАПРЕССОВКИ ПОТШИПНИКОВ !
I need this dia
Thanks for watching please subscribe to my channel ☺️
ایڈریس پلیز