Fixing My Motorized Bicycle plus Test Ride
HTML-код
- Опубликовано: 6 сен 2024
- Replacing the CDI on my motorized bicycle so the bike will work again. The CDI controls the spark of the spark plug, and without a working CDI, the bike won't work. I found a replacement on eBay for $10.
The 80cc motor on this Huffy Nel Lusso bike was purchased on eBay.
Check out my bike build here:
• Building a Motorized B...
As a tip only: Never forget to also check out your spark plug wiring and boot. That wire sometimes breaks or gets cracked, so it too can create issues. A little dab of dielectric grease in the boot also helps to keep moisture out so a clean spark is always present. Nice video and info.
That's the best running gas bicycle I've ever heard. It's smooth.
Nice! It runs smooth. Thinking of putting one on my bike.
I really enjoyed this video! I’m sure in NJ, I would be pulled over in a nano second! 35-40 miles to a tank....wow
Same for Nassau County, NY. They wrote me 7 tickets long ago when I was 16
Brake solution for grip brake.. Can get duel grip. One grip controls both brakes. Very good piece to use
Don't forget to check your coaster brake, and your wheel bearings time from time. They will definitely need to be cleaned and re-lubed.
Good job, runs so good I’m really quite surprised by the quality! I’m going to build one for sure! Thank You!
The old cdi still may have been good. The connectors in the wiring harness get loose sometimes, even wrapped electric tape. I have two bike builds and that's what happened on both. So check that before you buy a new cdi. I was a two minute fix
Your back fender is about to get sucked off
I was. Going 45 when my rear fender got ripped off the top fasteners and the one but the kickstand. Next a loud grinding sound and fishtailing cause my rear fender did a 180. It stopped because I had two struts to sturdy it
. So the rear isn't on the pavement I was justbpast the radar sign which said 45 slow down and the back of my bike was trying to catch up with the front from the left, seconds Earlier I overcorrrcted from being crossed up on the right. Before I could safely lay it down the rear skid / wheel Jamed into a small pothole / crack in the asphalt. I was surprised at how little the bike slowed as the rear in-hub Bendix brake was the first thing I applied but the tire was on the fender and the friction on my rear chrome fender detracted little from my speed. Anyway as I cartwheeled down examining Blvd I tore two ligaments in the right knee and put so much torque on my spine a cyst from my outer spine gut pulled into the conduit that houses the nerves and yourl fluid. And when I got twisted back around just as violently that cyst got jammed into the nerve bundle and I had the worst experience afterward. The pain shot down the left cheek Of my ass and down and around the left leg and foot. I count get out of bed for eight months. When I had to crutch to the bathroom it took 15 minutes for the pain to subside. Has neuro surgery. In January that fixed the nerve problem miraculously! I wouldn't go through the mri prep and the travel to fix the right knee so I kind now. Love the fender. It's not worth it. Wanted to
man that reminds me so much of my first build...that stock muffler sound. Cool build!
My daughter and I Love the shows dry the master link and use a bit of silicone to help secure it.? worked for our drag bikes.......GOOD LUCK......
Brilliant thanks so much for this. Mine's totally crapped out as well, I've ordered a new CDI but wasn't feeling confident. Hopefully I'll be back running when it gets here. Great vid
The ground wire on magneto likes to break to
You don't always need choke - although the last time I tried this was on a 1986 Ford when I cleaned the carb. Cold day, quick turn of the key and fired up after maybe 1 complete turn of the engine.
Thanks for taking the time to show us what you do. I'm looking forward to the day when I can assemble the whole kit to a bike by myself. I've tried it once in the past and failed, throwing both the new bike and new engine away. Wish I had your videos back then would've been great helped, because you actually go in depths steps to steps. That looks like a fun little ride you had going on there after the fixed...what city is that?
Hi I am learning from your videos and just subscribed to your channel. My youngest son rode his 2-stroke bicycle (like yours) up to visit me. It took him about 18 hours to go the 138 miles and less than 2 gallons of fuel! He used a lightweight bike trailer on the back to carry some food, drinks, tools, coat, etc. Anyway, I've been interested in "prepping" for quite some time, and I would like to build one of these. Your videos are going to come in really handy to help me figure things out. One question: while you had the back tire off to put the sprocket on, I was thinking that would be a good time to change out the tire to maybe a tubeless or something that would require less (and easier) maintenance. Any thoughts on that?
@Sma 556 i was thinking the same... unless he took long breaks
@@chicofromph33nix64 Aren't you only meant to run them for about an hour or so before letting the engine cool down ?
I thinking of fitting one to my built recumbent tadpole, thanks for the footage great result.
Dang that bike is fast!
PLEASE SOMEONE HELP. I recently put my motorized bike together. Without the spark plug in, the engine wants to turn over when I release the clutch. With the sparkplug, it does NOTHING. WHATS WRONG!
Bro I freaking loved the video!!! Please keep making these kinds of videos and I subbed too!!!!!!
Two years since this video was posted, hows the engine holding up?
And any tips on making these quiet?
Faisal Khan change the exhaust
@@arjunyeleshwarapu dont do that. 2 strokes need a vacuum
@@flynnlane6731 i mean how else can yoy make it quiet
@@arjunyeleshwarapu don't ride it
@@flynnlane6731 lol
I have bought 2 NT carburetors and both of them create an air leak where the flimsy "Metal bend over metal with a clamp" part is(carb to intake manifold). I see that you have the exact same design of nt carb and your carb might even be the same as mine. Your intake manifold "pipe" looks a lot better quality though. what do you recommend me doing to fix the leak? is there a way to seal the carburetor or should I just get a better intake manifold?
What a nice area you live in. Looks like where I live in Bangor Maine.
Ditch those fenders before they get you hurt. I’ve read too many guys eating pavement from fenders coming lose and locking up wheels at 25mph.
Thanks
That's what thread lock is for. :)
Hello I have got a bicycle and just waiting to get my 49cc motor and get it on to my bicycle that I can use it for getting to work and back home
Question??? I was told to re-torque my head on a new 2 stroke engine ? Should this be done ??? Thanks for the video 👍🏽👍🏽👍🏽
Why does it seem to have a lot of drag? Not very powerful, or bogged down? How much,does it weigh with your added? Fast and light is our motto!! But like the worker style bike congrats on a good build as well as the new CDI.
I bought this same bike from Walmart. I'm having problems with the chain going to the motor is rubbing against the bike. I don't see anything in the motor's manual that shows how to fix. Do you have any suggestions?
What would a little STP octane boost do, ?
I just bought the 80cc. with the racing carb. Luv your video 🤣🤣😊
What about adding an insulation jacket around the petrol tank to keep the fuel warmer, would that help with starting or not? I'm planning to do one of these conversions soon but I'm not riding down our potholed UK roads at 30mph!
Nice simple vid 😎😎 i literally ordered a kit off Amazon last week cant wait to get it .i may need a little help 🤣🤣
How did it go?
Just bought a engine mounted spring chain tensioner, do i need a longer bucking bar? Noticed clutch lever pin doesnt line up on point
Get carriage bolts for you back sprocket they with not rub on the brack arm.
Careful not to run STOP signs! Enjoyed the build, you did a good job!
Great video! Quick question, I plan on getting one of these kits and was wondering how loud it is when you are riding around with the stock exhaust?
Great videos Steve. Can you ride that thing in traffic with no special license?
Steve, you have inspired me to try building one of these cool bikes...yours is really cool! The beach cruiser bike that i recently bought is a 29 incher, would an 80 cc engine kit like yours work for a 29 inch wheel bike? Also, what can one do to tweek the engine to go 40 mph? Luv your videos bro! keep up the good work.
@@Steve_Does_Stuff How far of a distance can you go on a full tank of gas?
Where I live at..I can only go under 20mph when I get mine up n running
Generally change the magneto and cdi together.
How do you signal for turns? I didn't any lights on your bike and you can't take your hands off the handlebars
It sounds like the rear fender might be rubbing the tire, I've seen what that can do and it's not pretty... You should check that out just in case.
What was your setup for the original bike brakes? Cuz I think you said you were pedaling backwards for braking?
Is there a limit on how fast to ride in the breaking in period. How long does the breaking in cycle last
i like that basket over the front wheel where did you get that?
Also I just bought another one that has that the (front) tire is rubbing because the tire is too fat .I haven't even run tried to run it yet .I got it to fix for my grandson .I guess it would be dangerous to run with the tire rubbing.Any advice would be appreciated. I am new at all of this but willing to learn. ALSO, are fenders needed ?
Hi Steve.I have a few questions: Does the additional weight make it harder to pedal without the aid of the engine? How does the engine fare going up steep inclines? How much miles can you get out a full tank of fuel on average?
@@Steve_Does_Stuff Thanks Steve. Here's a hypothetical situation (assume that my biking ability is similar to yours):
I ride a normal bike on a flat surface with a normal pedaling force (one that I can sustain for extended periods of time) and I reach a speed of x mph. Now on my motorized bike I want to go up a relatively steep incline at the same speed. How much pedal assist will I need? E.g .is the amount of force I used on a flat surface on my normal bike enough? Sorry if the question sounds convoluted.
@@dw2843 From what riding mine has taught me, you don't really need to pedal all that much, if you don't care about slowing down a bit. I pedal a bit when going up the really steep hills around where I ride, but it really is only a bit. You'll have to pedal more if you decide to get a different sprocket that changes your max speed, as an increase in max speed means a decrease in torque, and I have definitely had that happen with the 32T instead of the factory 44T
Where did you get your kickstand, I'm getting an engine and would love a kickstand like that. That town looked like Norfolk Nebraska.
Thanks
Does it matter which CDI? Does any know where I should order one? I am going to have a friend (who I am going to pay) to help me
No sure how you even start it with the choke up i have to have mine down to start
Any ideal why 4 bearings ball fall out, when I was greasing the bucking bar? thank you.
The infamous nel lusso. Are they really as bad as everyone says?
how reliable has this bike motor proved to be? and how much heavier does it make the bike while normally pedaling?
do you install these on bikes for people i brought the kit but it needs to be installed on my bike
I wonder what the average mpg is on these bikes.
Hey I saw a comment saying you are from Minnesota, I am also from Minnesota and was wondering can I register one of these that I built to be a moped?
Is this really 80 CC? We have mopeds here that go 35 with 49 CC's so how doesn't this go much faster?
This motor has only one gear. Mopeds have variator transmissions, which are automatic belt driven transmissions that can change their drive ratio, so its like a pseudo multi gear transmission.
Dude I have one there janky a$$ China sub par motors that's why
i had to buy a new ignition coil for my kromag moped jut a year and a half after i got it
My bike wouldn't start one time. Went through all of your things. Ended up being a blocked Exhaust !!!!!
What are the laws on these things? How did you get it street legal?
YOU ~ ROCK ! !
I have the same bike, I feel like this is the problem I’m having. Before you replaced it did it pop off and muffle then die ? Cause that is what is happening to mine...
What spark plug did you replace it with thanks
Did you have to cut your fender or did you work around it
@@Steve_Does_Stuff Also assuming you drove it a lot did the welds hold for you.
Grate video I think you forgot the red gasket to the petcot
25 years ago when in my senior year college u used to ride a loop around metro PHX and get in 80 or so miles a day. I used to get 23 to 25 mph under pedals...along with good gearing. However the police waved and you failed to stop at stop signs and you failed to signal turns. I can count the tkts I've received not doing those simple tasks....you are a motorized vehicle on the road...follow laws.
Do you need a license to ride these? I would assume you do right?
Yeah I am getting one this spring I am nearly 60 I don't have a car lucky for me everything is close by I walk and the city bus can take me farther for $2 round trip
And watching this for me get extra parts like filters cdi spark plugs I will get a 4 stroke engine regular gas
I have too this engine ist very good i drive 40kmh but is drive 50kmh to.i have bike mtb weel 26/1.95 super.
30 mph with only coaster brakes, it doesn't seem too smart to me, when I did my bike I put a front brake on as well to have a little redundancy and little safety
Absolutely! I added front and rear brakes to be safe. I found a single brake lever that operates both the front and rear brakes. This lever is nice since the clutch lever takes up the space for a brake lever.
(I even made a video about that brake lever 😉)
This engine have a 3.2 km 65 cm3 real.but is power very good.can run 50 kmh and turqe is too very good its a dynamic engin.fine.
Steve do you get vibrations with the nel lusso, because with mine it vibrates when i hit 25 and its the fenders is that normal.
@@Steve_Does_Stuff hmm thanks for replying
@@Steve_Does_Stuff is your frame ok ive heard horror stories of them breaking where the rack is welded i just bought one
Hey Steve I have recently gotten one of these kits and have had some problems with mine maybe you can help if you have time, thanks.
Hey, if you don't mind my asking, in which state do you live? Here in Ohio I don't feel that the police would just wave!
How does it handle steep hills?
Next time let's hear how it sound before you charge it.Then change it So we hear and know the differences in how it sounded so we can remember the sound for those who are learning and watching .Thanks Again Doe !
how much was the cdi unit? i may get an extra right away
I paid $10 six years ago…bought it on eBay.
I’m thinking about building one how fast will it go and do have to get it street legal or register to drive on the street? Thank great video👍😊
As long as the feds don’t see you its legal.😉
Do you have just a standard 44 tooth sprocket on there?
@@Steve_Does_Stuff cool, I'm building one of those too, but am wondering if I should go to a 36 tooth sprocket? I only weigh about 96 lbs, so going up hills with that should be no problem, but I'm not sure...
@@Steve_Does_Stuff ok. Thanks
They Are not legal IN Texas
Mach yes they are I ride mine past cops all the time no problems
I've ridden mine about 10 miles and already the clutch cog has come loose, chain link came out and exhaust has fallen of twice, clutch cable has snapped aswell
# Clutch cog has come loose. If you used the socket (tube spanner) to rotate the sprocket when installing the chain, you could have loosened the nut. Use only removable thread locker on the shaft, be aware not to cross thread the nut.
# Chain link came out. This happens as there is not enough clearance between the chain and the clutch cover. As you have already run the motor, check the cover for chain contact. File the cover to increase the clearance. I also found this the hard way. Now fill the cover before final assembly. Make sure that the master link clip is correctly installed, round end in direction of chain movement.
# Clutch cable snapped. Check the cable routing, should be free and not bunched up ( kinked). The inner is standard Brake inner. You can apply light Oil on the cable before re installing. Did you lightly grease the Drive gear to Clutch Hub. as the Hub is fiber.
# Exhaust has fallen of twice. The Exhaust hangs on the two studs and vibrates working the nuts loose. Add lock nuts , two nuts / stud. Add a clump from the Silencer( Muffler in USA) to the frame. The clamps can be found at your local Hardware Store.
how is it going up hills?
My bike wont start I bought new chain new cdi and magento but it wont stay on.......
I have the same bike, looking for the right set up. Where did you get the motor Kit ?
CDI is available and don't wait on eBay supply and demand
Hey how to fix a puncture tire of 80 cc motorised bike?
Just the same as any other bike tire.
Bro I'm building my first one and it's like impossible to petal like I have to have someone push me while I'm trying to petal and there is no Idle I can't stop cause it dies
@@Steve_Does_Stuff naw it's something to do with the Piston i can feel it catching up I'm scared to crack it open cause I don't have the tools to make sure everything is tight enough but yeah I knew about the clutch I thought that was the problem had all 3 plates off trying to figure out what is jamming it up and I noticed it was catching at a certain point of the Piston moving up and down...also it doesn't idle if I stop it dies and it is extremely difficult to get someone to push start you at a 4 way when it's freezing outside nobody helps so I'm dragging a bike the back tire is locked and I'm crying
You could try only swapping the cable for better quality one. :) I dont belive those Chineese cables a bit ! :)
Sorry guys are this thing legal on the street?police man can stop me for riding this on a street?what type of license i need?thanks
Thank you :)
Is this legal?
I bought a new cdi and magneto and cleaned out carb and still don't start help!
check youre fuel line
add teflon tape intake manifold and use gasket sealer on the gasket by the block
Does anybody know any machanics near York or Clover
Do you lose the ability to change gears?
Steve thank you!
Do you need to wear a helmet? Did you have one when police passed?
My chain was to short very weird
In Quebec I would have gotten a ticket and my bike impounded.
The MOST EEFED up thing is NOBODY has a single Huffy Cranbrook or Del Nuso in stock! Unless its a girls frame! Seriously! And sellers price them like they already have an engine on them!! Lol
I managed to get a tuesday may 1 cruiser bike for 100 bucks not too shabby
my carbutator is liking gas hoe a do estop that?
👍🇺🇸👊
Your videos show good running well-built equipment being operated unsafely. As a vehicle driver (all bikes are vehicles), you are required to stop at stop signs. In one case it looked as if you failed to yield the right of way to a car on your right. Please, use your videos to teach good, safe driving habits as well.
Look, I'm going to level with you on this one. Good safe driving habits are important, but I don't come to RUclips to worry about how other people should drive safely. We could have a conversation about hand signals, the lack of a truly sufficient braking system, or missing rear view mirrors; but that's not the point here. This content creator, is having fun testing out his motorized bicycle, that he just fixed. Sit back and enjoy video for what it is.
My chain broke first ride
It broke near the master link but not at it