DIY 18650 Battery Charger - How to make lithium-ion cell Charger
HTML-код
- Опубликовано: 24 авг 2024
- Subscribe to My Channel: bit.ly/2JHtlyc
In this video I am showing you how to make a Li-ion 18650 Battery charger with Charging Discharging and Battery level monitoring features including every single step of making. Using this Battery Charger, you can check and identify 18650 battery capacity, whether it is Good one or bad one.
For this project I have used following parts:
1) 18650 Battery x4
2) TP4056 Charger module with discharge protection X4
3) 18650 Battery Holder (4 pcs Battery Holder) x1
4) Three Position 6 pin ON/OFF switches x4
5) LED 3V Red, Green & Blue x4each
6) LED panel Voltmeter 3wires x4
7) 10W 10R Ceramic Capacitors x4
8) 12AWG & 18AWG wires
9) Heat shrink tubes (heat Sleeves)
10) 1KOhms Resistors x4
11) PCB spacers 1inch with nuts x6
12) Acrylic Sheet
13) 5V 3-4A charger or power supply
14) Cable ties
15) Piece of Wood
16) Epoxy Glue / Glue Gun with Sticks
17) Color Spray (Juki Grey)
*Dimensions of the Panel available at 2.52 in the video.
*Circuit Diagram of the Battery Charger available at 11.57 at the video.
Note: Use 5V 4A Charger to reduce excessive charging time.
DIY Grinder Machine used in this video : • DIY Grinding Sanding m...
Thank you.
Subscribe for more future creative project videos.
Subscribe Here: bit.ly/2JHtlyc
#diycharger #18650battery #tp4056 #liionbatterycharger
Did you just copy Sorins project video.. Damn this is not cool bro!
Yes he copied this : ruclips.net/video/Z3IGyE39otA/видео.html
Those ceramic 10ohm/10watt resistors will get *very* hot - I would be seriously concerned about all the wiring that's touching or close to them melting - fire hazard.
Best copy I have ever seen!🤣
You copied idea , basically everything from creator Sorin DIY Electrical Nerd. You didn't give any credits or links to his video.
Please make this again but for a single battery only.
Thank you 🇮🇳
Great job with all the best information and knowledge
Its a copy from sorin
yes it is
@@Sorin_DIY It shows that only good stuff is being copied! :-))
It seems that all this guy does, is exactly copy from others, albeit a fair while later. He also copied the ATZ power supply diectly from another RUclipsr. Rather poor when he doesn't bother to give credit.
This guy stole ewerithing from sorin ewen power bunk and powersuplay
Can send the drawing of the plate?
Did you copied this proyect to sorin? There is the same in his channel.
True, exactly the same project!! And not the only project similar with Sorin's channel....
Ok the project itself is great, unfortunatly there is no explanation at all here, so better go with Sorin's version which is explaned nicely, and btw, Sorin does its best to answer to questions, if you intend to realise his projects ;)
Good project and design but you did not adjust the trimpot on the back of the small LED displays to accurately display the correct voltage. Hooking them up to a multimeter at the same time on one of the batteries and adjusting the display to the multimeter reading would be fine. For anyone new to LI-ON batteries, charging them above 4.20 volts can be dangerous and degrade your battery life.
Thank you. Thank you for your suggestions.
These modules come in various versions, they do not always have a trimpot unfortunately
[EDIT] Ah, these ones in the video do I see now :-)
Sorin
Wow hebat aku sangat menyukai caranya
Excellent project 👍
Thanks
I like this video super good Sir
Хороший зарядник 👍👍👍👍👍👍👍👍👍👍👍👍
схему подключения покажи!
yea those cheap volt meter messed everything up plus whats the point making discharge if you cant read the mah ? anyway you get in there
un peu inutile mais on ajoute un module qui donne les Ah/Wh et c'est super.
hi, i really enjoyed your video. Could you tell me what the 4 white rectangular pieces are that you showed after the led lights please?
Ceramic Capacitors
You coppy diy Sorin
Hi.
Great, i would like to make the same and plug it at a solar panel.
Can you tel me please what the différence between the bat +/- and the out +/-
Thank
The difference is that you connect the battery on the bat +/- and you get an output voltage of 4.1v
You are doing the same @Sorin - DIY Electrical Nerd proyects. I have seen 3 videos and you have THE SAME PROJECTS, CLONES !!!!!. You are a fake.
very creative. love your projects. you make it look so simple
Thank you
What is it mean if the battery turns red
Hey wow create....but please share u r purchase spare side
Vishwanathan Vallal Sure
Where did you by lithium ion battery
🙏 thanks..
1kohmes resistance for what.. ? Please explain thanks
Check out at 9.55 in the video. It's to reduce voltage (As Protection) for LEDs.
Super project
At what rate does it discharge
I've used 10ohm resistors to discharge the cells. so the discharge current will depend on the battery voltage. I=U/R. when the battery is fully charged, the discharge current will be: 4.2V/10ohm=420mA.
@@LahisTechLT this will be a calculative value. The total discharge current measured through imax b6 and yours diy will be approximate or large variation ?
Can you include power adapter from ac to DC in this board
So we only need to connect ac
how bout some credits to the creator ruclips.net/video/Z3IGyE39otA/видео.html not the only creation of his found here
The name of the cad software you are using. thanks
Solidworks
Can you make 3.7v battery indicator digital one
Now am watching u r channel quickly subscribed u r channel
voltage meters are not calibrated ---- shows wrong readings ...
yeah, it should be done.
So don't buy Chinese crap. :-))
@@LahisTechLT Exactly how do you intend to "calibrate" them? It would make an interesting video. I'm sure everyone using these boards would like to see how you manage it. :-)
This is a rip-off. Original design: ruclips.net/video/Z3IGyE39otA/видео.html
It's a nicer build than Sorin's only due to the acrylic - he used wood
No sound 😂😂😂
Why ?
👍👍👍👍👍👍👍👍
you must calibrate those volt meters. you can't be so noob
👍👍👍👍👍😀😀😀😀😀