After activating pbo in the bios the fans , cpu and system fans are att full speed when entering the bios? I adjusted the fan curve in smart fan but the cpu fan is fluctuating
It doesn't have backup bios but it has Q-Flash Plus which is their ability to flash without CPU, Memory, GPU. No heat issues that I saw, The case did have good airflow.
Hi, I have a problem with this board. The only RAM slot that is working is the B2 slot, when i add a second RAM in A2, B1, or A1, the PC does not POST. Would there be a way to enable one of those slots in the BIOS? Appreciate the help
Hey! This video is a bit old, but I wanted to share my issue and ask for advice. I got my motherboard and it came with a bent pin on the cpu socket, still it powered up and detected my ryzen 7800x3d. The problem is that it wasn't booting from a flashdrive to install windows, it just came back to the bios again and again. I tried downloading windows on my ssd drive in another computer and then trying to boot from it and still the same issue. It tried to boot from it but just came back to the bios again. I brought it to a technician and they said the motherboard is malfunctioning and told me to get my money back. I asked for a refund from amazon and I am waiting for the money in order to buy another one. My question is, do you believe it was a problem with this specific motherboard? Was there something I missed like updating the bios (wich I tried but had no idea how to do so)
I would be concerned that the bent pin was the issues or maybe just a bad board in general. since you did get it booted up to bios you can always check the version with the one on gigabyte site to see the differences.
I see you've a Ryzen in this, did it work with the CPU out the box or did you have to bios flash it? Getting a Ryzen 5 7600 and this motherboard, don't mind doing q-flash but it is nervewracking.
Yes, have windows on a USB and have it set as the item to boot in the boot sequence. You could plug in the USB and then on boot hit F12 (I think this is the key for the boot menu on this board) and that should bring up the boot menu to select the USB. Let me know if you have questions.
Gigabyte, as well as other manufacturers will pull bios. I would update to the latest with out a trailing letter. The b or c that is trailing is usally a beta one.
Yes, drives you can download from their site. If you are looking at updating bios, I put the bios file on the USB and then use Q-Flash in the bios to upgrade.
Hello Sir, i have a B650 gaming x ax v2 and i’m not able to install windows11. I have the latest bios version but it doesn’t show me tpm 2.0 like in your video. Maybe you can help me.
i have a problem with my gaming pc, i have a 3060 and an i5-12400f with same bios, with everything on stock settings i get around 130 highest on lowest settings possible on wz3, and in on some games i feel like im not getting the full potential i can rlly get. after over clocking my gpu i got a lot more performance boost but it didnt feel enough and after turning on a lot of settings in bios for cpu i got around 170 high on everything low wz3, which is a lot better but i dont know what half of the settings in bios i turned on does and i feel like getting this much fps comes with a cost of harming my pc, i was wondering if you could make a video of the best possible bios settings to get higher fps without damaging my pc, thanks
I am guessing you have a b660 intel board if you have a 12400f. If I had that setup I could go thru something. I don't have an intel setup that is a non k chip.
Where can I change ram frequency from 6000 to lower frequency’s I had a asus board before and I can’t seem to find it on this new gigabyte I watched the whole video a bunch of times
I just put a bunch of new parts together and tried booting it up without updating the bios and I'm having issues getting into bios properly. Would it be safe to assume it's from not updating the bios first? I missed the part where you said you updated it.
You can use it straight out of the box if the cpu you are using is supported on the bios that is already installed on the board. I hope that makes sense. If not let me know.
Hi man! I have this motherboard and it should have some RGB working on it, but I can't figure it out why it's not working, might be the guy who put it togheter fault?
Thanks for the video! Finished building a pc with this motherboard and it's been working fine for about a month but today, the wifi stopped working and just shows that there are no networks found. Redownloaded amd wifi drivers but still doesn't work. Was looking for a wifi option in bios to see if it somehow turned off but ig there isn't one. Any ideas on what the issue could be?
Seems like that clears out the residual power in caps etc. for a pure reset (keeping it basic). This is usually the first thing I tell people to do when they have an issue that just started, Gets me to a clean slate on where to start problem solving. And many times, just fixes it. :)
Hello. Yesterday I updated the bios and I'm having problems with the video output . Can you tell me where I have to go in the bios to put the dedicated graphics card and not use the integrated one? I think that's the problem. Thank you
Hey , i have a question , i can't find a setting to set the number of "lanes" to wich my ssd runs , currently crystaldisk info says it only uses 2 hence my low read/write speeds i would assume , my ssd is a corsair mp600 pro 1T version wich is currently at 3.5kmb/s read/write that's almost half ... Any advice ?
@@GrayaOverload A ryzen 5 7600 , the first one below the gpu so i would assume the #1 , it's the only ssd installed and i unplugged the 2 sata hdd's to test , also i tested both slots on the board both same issue , i have to mention by mobo is a gigabyte b650 x ax matx rev1.3 thanks for your quick reply , i'm starting to believe it is the mobo i was under the assumption that the ssd was the problem i don't know what to do , and i have limited time to return the mobo so that i can get my money back i'm so confused in what to do
@@zolotovicialexandru7468 Try a bios update first, if you are not on the latest. I don't think it will fix it, but you never know. It sucks but you have to start with something mobo, drive or CPU are all options.
@@GrayaOverload I ran hwinfo and the motherboard recognizez pci-e gen 4 and x4/x4 on both slots although the base bus device function number is on the 1st slot 0:1:2 and the 2nd 0:2:2 i would assume it only attributes 2 lanes of communication , why tho ? is it the mobo , the cpu or the ssd ?
hi, I just updated my PC and used this motherboard, when I turn it on I see that windows sees my internal disks (ssd, hdd) as external disks, could you help me? the data is set in AHCI.
Sounds like a windows issue. I would start with windows updates. Maybe a bios update would help but I doubt it. Look at disk management to see what it says as well.
I have a problem maybe you can help me when I’m starting my pc it’s instantly goes in the BIOS and I don’t know what to do and my thought was to update the bios the pc is not new or something I already played games like 8 months without any problems and yesterday I turned of my pc and then I was stuck in the bios
@@user-dq9xj3et2c Go thru Q-Flahsh and follow the instructions. It almost sounds like you have a Windows corruption issue, since your drive show up and is set to the boot device. Might have to do a repair on Windows.
@@GrayaOverload my temps while gaming hit 95 degrees all the time , i use Deepcool Gamaxx LE500 240mm liquid cooler with ryzen 7 7700x paired with 7800XT , please let me know how to fix the CPU temperature 😁
@@Kolestroll-cg1hx yes , even though it raised to 90 degrees playing some games like AC origins, then i checked up the liquid cooler, the screws were loose and the thermal paste isn't intact with the cpu, i cleaned up the stock thermal paste in the liquid cooler and applied Arctic MX-4 in the cpu, now the cpu runs 44 degrees at idle and 60* at games 😁 thanks for the help
I have a b650 gaming x ax and ryzen 5 7600x; when I boot up the pc after the bios flash screen it doesn’t appear anything. There are no red lights in the mobo. Should I update the bios? It’s version F2, the actual is F24
@@luisbravo7445 I would open a support ticket first. If the keyboard operation were normal speed I condiser it normal. By open a ticket with support might help them say rma or put a fix in a future bios update.
When i download the driver from Gigabyte's wesite, it comes as a .zip file. Do I need to unzip before using it? Or I can just drag the zip file to the usb and it can work?
@@GrayaOverload After I unzip, I got several files. Do I need to put all of them into the USB? There is one pdf file in those that says something about BIOS Flash SOP, I am not sure what that is about
Sorry I didn't see the other comment on my phone last night. I only put the bios file on the USB for when I boot up into bios to use the flash tool in bios.
I think it is under Tweaker > Advance CPU Settings > Precision Boost Overdrive and once in that page change Precision Boost Overdrive to Advance. Then you should see the Platform Thermal Throttle
Hey I just build a pc with the same board and a ryzen 7700x I tried to flash the bios to the most updated (f22b) current is fb. I keep getting the bios id check error. Any help would be greatly appreciated
Did you download the bios for the right Rev. There is currently a gigabyte B650 Gaming X AX with multiple revs, and then there is the Gigabyte B650 Gaming X AX V2
I don't see a beta bios for this board on their site currently. You go to Gigabyte site, find the board, click Support and then under downloads there is BIOS, expand that and you will see F9d (current version). I download it and put it on a USB drive and boot into bios and use the upgrade tool in there.
If I get my hands on this board again I will update. I hope someone else can update this otherwise. Gigabyte info on the webpage leaves much to be desired. Realtek® Audio CODEC High Definition Audio 2/4/5.1/7.1-channel
Then don't enable it. I have seen this I did a manual tune on the memory. If it has more than one expo profile you could try a different profile. There are a few reasons as to why Windows will crash, expo enabled something that doesn't work with it, could be voltage not supplied when it is needed, could be the CPU memory controller, could be the motherboard, or even memory.
I would first try a bios update and then try again. If that doesn't work, I would have to say file a support with Gigabyte. Options should keep until you reset.
@@GrayaOverload this worked thank uyou sorry for the super late reply another question if you may, how do I get my BIOS to display on my monitor while plugged into a gpu? I can only see my bios if I plug it into my monitor. thank you so much bro
I don't remember, and since I don't have the motherboard with the latest bios as this is a build for someone else, i hope someone will be able to answer. Another place you can go is ask gigabyte support.
Наука
![[ GUILTY GEAR STRIVE: DUAL RULERS ] Teaser Trailer](http://i.ytimg.com/vi/e4TDqaE3XAg/mqdefault.jpg)
Beautiful guide! Well explained, I'll also share it on my channel for my motherboard 🤩
thx for the video! hope ur channel grow
Thank you.
After activating pbo in the bios the fans , cpu and system fans are att full speed when entering the bios? I adjusted the fan curve in smart fan but the cpu fan is fluctuating
Hi. Didn't see the eco mode option in bios. Cant find it in the aorus elite ax either. Had to set limits manually.
Hey
Does this board have a backup bios?
And do you recognize any heat problems with EXPO enabled?
Thank you and great video
It doesn't have backup bios but it has Q-Flash Plus which is their ability to flash without CPU, Memory, GPU.
No heat issues that I saw, The case did have good airflow.
Hi, I have a problem with this board. The only RAM slot that is working is the B2 slot, when i add a second RAM in A2, B1, or A1, the PC does not POST. Would there be a way to enable one of those slots in the BIOS? Appreciate the help
No, that would have to be an rma of the board or a exchange from where you bought it.
Thanks man
Your welcome.
Hey! This video is a bit old, but I wanted to share my issue and ask for advice.
I got my motherboard and it came with a bent pin on the cpu socket, still it powered up and detected my ryzen 7800x3d. The problem is that it wasn't booting from a flashdrive to install windows, it just came back to the bios again and again. I tried downloading windows on my ssd drive in another computer and then trying to boot from it and still the same issue. It tried to boot from it but just came back to the bios again. I brought it to a technician and they said the motherboard is malfunctioning and told me to get my money back. I asked for a refund from amazon and I am waiting for the money in order to buy another one.
My question is, do you believe it was a problem with this specific motherboard? Was there something I missed like updating the bios (wich I tried but had no idea how to do so)
I would be concerned that the bent pin was the issues or maybe just a bad board in general. since you did get it booted up to bios you can always check the version with the one on gigabyte site to see the differences.
I see you've a Ryzen in this, did it work with the CPU out the box or did you have to bios flash it? Getting a Ryzen 5 7600 and this motherboard, don't mind doing q-flash but it is nervewracking.
Worked out of the box.
@@GrayaOverload Thank you, appreciate the answer :)
for install windows 10, I can do it with an usb with windows installer and press basic mode> boot Sequence> usb? Or how. thank you!
Yes, have windows on a USB and have it set as the item to boot in the boot sequence. You could plug in the USB and then on boot hit F12 (I think this is the key for the boot menu on this board) and that should bring up the boot menu to select the USB. Let me know if you have questions.
I can’t find my bios version in gigabyte site it’s f9c I want to upgrade it and I don’t no what version should I download
Gigabyte, as well as other manufacturers will pull bios. I would update to the latest with out a trailing letter. The b or c that is trailing is usally a beta one.
I don’t want to mess up my windows install usb, so am I able to boot without updating drivers, and update them once the pc is on?
Yes, drives you can download from their site. If you are looking at updating bios, I put the bios file on the USB and then use Q-Flash in the bios to upgrade.
Thanks man. Is the TPM Module on by default so I can install Windows 11 via Bootable USB Stick?
With the bios for windows 11 support, yes. Older bios no.
I plan on getting this board. Can i put the update for the bios in the same usb as my Windows install
Yes, I do that all the time.
Hello Sir, i have a B650 gaming x ax v2 and i’m not able to install windows11. I have the latest bios version but it doesn’t show me tpm 2.0 like in your video. Maybe you can help me.
Have you tried resetting the bios to default?
i have a problem with my gaming pc, i have a 3060 and an i5-12400f with same bios, with everything on stock settings i get around 130 highest on lowest settings possible on wz3, and in on some games i feel like im not getting the full potential i can rlly get. after over clocking my gpu i got a lot more performance boost but it didnt feel enough and after turning on a lot of settings in bios for cpu i got around 170 high on everything low wz3, which is a lot better but i dont know what half of the settings in bios i turned on does and i feel like getting this much fps comes with a cost of harming my pc, i was wondering if you could make a video of the best possible bios settings to get higher fps without damaging my pc, thanks
I am guessing you have a b660 intel board if you have a 12400f. If I had that setup I could go thru something. I don't have an intel setup that is a non k chip.
Where can I change ram frequency from 6000 to lower frequency’s I had a asus board before and I can’t seem to find it on this new gigabyte I watched the whole video a bunch of times
You can turn off expo which will take make it default memory speed. if you want to manual tune it the SPD setup around @6:43 in the users settings.
This is more of a BIOS review than a motherboard review. Would have been nice to discuss layout, power requirements, etc.
Yes, this is just a bios walk-thru of the board. Take a look at the unboxing of this board. ruclips.net/video/qK7Xh_nbFU8/видео.html
So there isn’t a Dram high voltage mode? Not sure if I overlooked something
I don't think so.
I just put a bunch of new parts together and tried booting it up without updating the bios and I'm having issues getting into bios properly. Would it be safe to assume it's from not updating the bios first? I missed the part where you said you updated it.
I think you can use Qflash plus to update bios. It could be your issue. I would check everything first and then to to the flashing.
did u figure it out
Hi just saw this video do you know if i have to get a bios file before setting this up or can i just use my motherboard straight out of the box?
You can use it straight out of the box if the cpu you are using is supported on the bios that is already installed on the board. I hope that makes sense. If not let me know.
I got a new ssd and I’m trying it keep loading me into bios what should I do guys?
Did you clone the old ssd or swapped them out or added it?
Hi man! I have this motherboard and it should have some RGB working on it, but I can't figure it out why it's not working, might be the guy who put it togheter fault?
Did you plug the rgb items in the right rgb ports?
I have the same mobo, can someone please tell me why the bios looks different?
What bios version do you have?
is it possible to change the bios resolution on this motherboard or its also for you low
It isn't possible to change the bios resolution. It was low for me.
Thanks for the video! Finished building a pc with this motherboard and it's been working fine for about a month but today, the wifi stopped working and just shows that there are no networks found. Redownloaded amd wifi drivers but still doesn't work. Was looking for a wifi option in bios to see if it somehow turned off but ig there isn't one. Any ideas on what the issue could be?
Does it show up in device manager?
@@GrayaOverload nah it doesn't show up in device manager
Unplug power, then hold the power button for 30 sec and then plug back in and hit the power button. Let me know if that works.
@@GrayaOverload holy crap that worked. thank you so much. what was the reasoning behind that? that is so interesting
Seems like that clears out the residual power in caps etc. for a pure reset (keeping it basic). This is usually the first thing I tell people to do when they have an issue that just started, Gets me to a clean slate on where to start problem solving. And many times, just fixes it. :)
Hello. Yesterday I updated the bios and I'm having problems with the video output
. Can you tell me where I have to go in the bios to put the dedicated graphics card and not use the integrated one? I think that's the problem. Thank you
@11:03 shows the settings for the pcie and integrated gpu options
@@GrayaOverload Thank you very much💥
@@LuKeTt__ you're welcome
Do you use the flash program with in the bios ?
Yes
I turned on my pc for the very first time after build and it has a red light on motherboard
There should be 4 led red lights in the same area. They are for Boot, vga, cpu, memory. Page 19 of the manual. Let me know which one it is.
Hey , i have a question , i can't find a setting to set the number of "lanes" to wich my ssd runs , currently crystaldisk info says it only uses 2 hence my low read/write speeds i would assume , my ssd is a corsair mp600 pro 1T version wich is currently at 3.5kmb/s read/write that's almost half ... Any advice ?
There isn't a setting in bios. What cpu do you have? What slot is the drive plugged into? How many other pcie devices do you have connected?
@@GrayaOverload A ryzen 5 7600 , the first one below the gpu so i would assume the #1 , it's the only ssd installed and i unplugged the 2 sata hdd's to test , also i tested both slots on the board both same issue , i have to mention by mobo is a gigabyte b650 x ax matx rev1.3 thanks for your quick reply , i'm starting to believe it is the mobo i was under the assumption that the ssd was the problem i don't know what to do , and i have limited time to return the mobo so that i can get my money back i'm so confused in what to do
@@zolotovicialexandru7468 Try a bios update first, if you are not on the latest. I don't think it will fix it, but you never know. It sucks but you have to start with something mobo, drive or CPU are all options.
@@GrayaOverload I ran hwinfo and the motherboard recognizez pci-e gen 4 and x4/x4 on both slots although the base bus device function number is on the 1st slot 0:1:2 and the 2nd 0:2:2 i would assume it only attributes 2 lanes of communication , why tho ? is it the mobo , the cpu or the ssd ?
You don't happen to have another nvme drive to test?
its giving me coil whine any idea what setting might fix this?
I don't and I don't know if a setting will fix it.
hi, I just updated my PC and used this motherboard, when I turn it on I see that windows sees my internal disks (ssd, hdd) as external disks, could you help me? the data is set in AHCI.
Sounds like a windows issue. I would start with windows updates. Maybe a bios update would help but I doubt it. Look at disk management to see what it says as well.
i found out that you have to turn off chipset SATA port hot plug @@GrayaOverload
I have a problem maybe you can help me when I’m starting my pc it’s instantly goes in the BIOS and I don’t know what to do and my thought was to update the bios the pc is not new or something I already played games like 8 months without any problems and yesterday I turned of my pc and then I was stuck in the bios
While you are in bios do you see a nvme, or sata device? any options under the boot menu?
@@GrayaOverloadno it’s looks the same like in the video
@@GrayaOverload i have a usb with a bios update now can you maybe tell me where I can update it or how I update it thanks a lot
@@user-dq9xj3et2c Go thru Q-Flahsh and follow the instructions. It almost sounds like you have a Windows corruption issue, since your drive show up and is set to the boot device. Might have to do a repair on Windows.
@@GrayaOverload thanks i just installed windows again and its working again thanks alot for your help
Hey i have the same motherboard and processor but my idle temps sit at 60 degrees any fix ? I also have an liquid cooler
First thing I would check is the mount of the cooler to the cpu, re-apply a good thermal paste. That is where I would start. What AIO are you using?
@@GrayaOverload my temps while gaming hit 95 degrees all the time , i use Deepcool Gamaxx LE500 240mm liquid cooler with ryzen 7 7700x paired with 7800XT , please let me know how to fix the CPU temperature 😁
@@Kolestroll-cg1hx hi, what is that fix please let me know 😁
@@Kolestroll-cg1hx thank you so much 🥰
@@Kolestroll-cg1hx yes , even though it raised to 90 degrees playing some games like AC origins, then i checked up the liquid cooler, the screws were loose and the thermal paste isn't intact with the cpu, i cleaned up the stock thermal paste in the liquid cooler and applied Arctic MX-4 in the cpu, now the cpu runs 44 degrees at idle and 60* at games 😁 thanks for the help
More recent Dec F20> bios is very different UI
Thanks for the update. I don't have this board to do another video on this as it was a build for someone.
Man i have 4 choices is xmp 1 and xmp 1 and exbo 1 and exbo 2 what ido
Start with expo2 if that has stability issues then go to expo1 then to the xmp choices.
I have a b650 gaming x ax and ryzen 5 7600x; when I boot up the pc after the bios flash screen it doesn’t appear anything. There are no red lights in the mobo. Should I update the bios? It’s version F2, the actual is F24
To clarify the bios screen flash on screen? If so can you see or access the bios? I would update bios in either case.
@@GrayaOverload yes I can access the bios. I accessed it, save and exit but then always black screen. So I’ll try to update the bios
Bios Updated correctly, there were some random reboots but I’m still waiting for something in output…
@@salvoromano23 have you tried to install windows?
I tried cause randomly it booted, but after selecting the 240hz resolution the monitor crashes (ofc the monitor is 240hz) and it is not booting up.
🫡 so I have this board with a 7600x but I’m upgrading to the 7800x3D, I was just wondering if I had to do anything beforehand
Check your BIOS to make sure the version you have supports 7800x3d.
Hi! I bought this board and my mouse is very slow and stuttery while moving through the BIOS. Is it normal? ( I tried different mice )
I have seen this on some bios, that is why most of the time I use the keyboard.
@@GrayaOverload Should I RMA? or is it pretty normal
@@luisbravo7445 I would open a support ticket first. If the keyboard operation were normal speed I condiser it normal. By open a ticket with support might help them say rma or put a fix in a future bios update.
@@GrayaOverload Okay, thank you!!
@@luisbravo7445 no problem
When i download the driver from Gigabyte's wesite, it comes as a .zip file. Do I need to unzip before using it? Or I can just drag the zip file to the usb and it can work?
You will need to unzip
@@GrayaOverload After I unzip, I got several files. Do I need to put all of them into the USB? There is one pdf file in those that says something about BIOS Flash SOP, I am not sure what that is about
Is it just the .f20a file that I need for my Gigabyte B650 X AX?
@@puyuanzhang9069 Yes, that is the bios file.
Sorry I didn't see the other comment on my phone last night. I only put the bios file on the USB for when I boot up into bios to use the flash tool in bios.
hello, xmp option only allows 'disabled' and i cannot change it to enabled. how can i fix that?
What RAM do you have? Does it have XMP profile?
@@GrayaOverload its ddr5 netac shadow 2
Model number, they have many options
@@GrayaOverload c40 black
DDR5-4800? If so that might not have a xmp profile.
idk how to enable tpm on this board
It is enabled by default when I set it up. Ftpm is what should be on.
Hi, is there somewhere in the bios where you can set the PPT?
I think it is under Tweaker > Advance CPU Settings > Precision Boost Overdrive and once in that page change Precision Boost Overdrive to Advance. Then you should see the Platform Thermal Throttle
@GrayaOverload hi, thanks but I'm looking for the Package Power Tracking (PTT) option.
@@egonlasso6846 sorry about that. Let me look again.
Hey I just build a pc with the same board and a ryzen 7700x I tried to flash the bios to the most updated (f22b) current is fb. I keep getting the bios id check error. Any help would be greatly appreciated
Did you download the bios for the right Rev. There is currently a gigabyte B650 Gaming X AX with multiple revs, and then there is the Gigabyte B650 Gaming X AX V2
I have the 1.0 gaming xax
It’s definitely the right one I just keep getting the check error
@@TTVAyyDak are you trying this thru windows using the Gigabyte app center with @BIOS or thru bios?
@@GrayaOverload through the bios screen when you start the pc should I install windows first?
how do you access rgb controls
thru their software, you will have to download and install it.
How temp time gaming ?this motherboard vrm good?
I wasn't able to get gaming temps as this was built for someone.
hey can you please help me out on how to dowload the bios? thank you
I don't see a beta bios for this board on their site currently. You go to Gigabyte site, find the board, click Support and then under downloads there is BIOS, expand that and you will see F9d (current version). I download it and put it on a USB drive and boot into bios and use the upgrade tool in there.
@@GrayaOverload through q flash??
@@1down5ups yes
Hi
Which is the realtek audio model?
If I get my hands on this board again I will update. I hope someone else can update this otherwise.
Gigabyte info on the webpage leaves much to be desired.
Realtek® Audio CODEC
High Definition Audio
2/4/5.1/7.1-channel
How many fans can we connect to mobo?
1 x CPU fan header
1 x water cooling CPU fan header
2 x system fan headers
1 x system fan/water cooling pump header
when y enable EXPO windows 11 wil crash
Then don't enable it. I have seen this I did a manual tune on the memory. If it has more than one expo profile you could try a different profile. There are a few reasons as to why Windows will crash, expo enabled something that doesn't work with it, could be voltage not supplied when it is needed, could be the CPU memory controller, could be the motherboard, or even memory.
@@GrayaOverload After setting bios default y can use EXPO 1 PROFILE.
Y wil sub your channel :)
This mobo require 2 EPS cable?
Dont have.
This board works best for windows 10?
It should work good for windows 10 and 11.
how to disable integrated graphics ? can you help me ?
about @11:02 there is an option of Intergrated Graphic it is set to auto in mine, but you can disable it there.
@@GrayaOverload i disabled it and it turns back to auto.
I would first try a bios update and then try again. If that doesn't work, I would have to say file a support with Gigabyte. Options should keep until you reset.
How to enable the wifi 6e that comes with it
It will s enabled by default in bios. Install the required driver from their support site
@@GrayaOverload this worked thank uyou sorry for the super late reply
another question if you may, how do I get my BIOS to display on my monitor while plugged into a gpu? I can only see my bios if I plug it into my monitor. thank you so much bro
@@jjdude86 I have had this once and I don't remember what exactly was plugged in hdmi or display port but I did the opposite.
@@GrayaOverloadthanks for your time bro
@@jjdude86 no problem
Does it have hpet option
I don't remember, and since I don't have the motherboard with the latest bios as this is a build for someone else, i hope someone will be able to answer. Another place you can go is ask gigabyte support.
how do i boot windows
Have you installed windows? If not you will need to get windows install on a USB drive and then install windows.
only 3 of my fans pop up and i have 5
are all 5 fans spinning?
Hi, how can I enable the tpm 2.0 on this motherboard?
It should be enabled as a default.