Mx5 Mk3 - Have you been cleaning your hood drains wrong? Here’s my two cents!
HTML-код
- Опубликовано: 20 июл 2024
- After watching a video from Mx5restorer aka Lights up lights down RUclips channel see link below:
• How to unblock your Mk...
I thought I would add my additional camera angles as I had much more access than Chris did at the time and if it wasn’t for that video I would not have checked mine.
Before that I used the method as recommended by thousands of forums, videos etc of the trombone cleaner, which I found would unblock and clear some of the mess but not fix the issue completely and would occasionally inver the seals causing more restrictions and road noise!
Drain cleaner used in the video:
Trumpet Cleaning Care Kit Trumpet Mouthpiece Brush Valve Brush Flexible Brush with Cleaning Cloth, 3 Pieces www.amazon.co.uk/dp/B06XJJ9NV...
Mx5 Europe links:
mx5-europe.club
/ mx5europe
/ mx5europe
/ naeurope.club
/ nbeurope.club
/ nceurope.club
/ ndeurope.club
• MX5 Europe Club Nights
Patreon link:
/ mrmazdaguy
0:00 Intro
0:11 Bad joke alert
0:16 borescope shots!
0:46 removing seat belt drum
1:01 how to remove drain tube
1:26 cleaning roof drains manually
1:42 inverted roof drain seal
2:20 nobody tell the wife!
2:33 reinstalling drain tubes
2:55 trombone cleaners invert seals and here's the proof
3:32 a community vote result
4:34 outro and beg for subs! 
Авто/Мото
By far the best video on drain cleaning I'm the MX5 I have seen and I will be doing this to my NC MX5 . Thanks a whole bunch.
Thanks, but as mentioned in the video it’s merely an expansion on the lights up lights down video
This is great content, thank you so much! I own a mk4 and the drain pipe design is a nightmare in comparison haha
Sure is, my old man wants me to take his drains out in his mk4 recaro. Makes me nervous just looking at it.
Great video, it helps a lot. I now have a lovely clear drain hose. So satisfying to see water pouring from under the car. Thank you.
Thanks!
Make sure you watch the RUclips link in the description to find out what and how you need to remove to access the drain. This video then makes it much clearer exactly how to fit and clean the drains. Much better than a trombone cleaner when yours is really blocked. Thanks for posting
I used the trombone cleaning method and ofcourse one of membrane became inverted causing roadnoise. This video should be seen by all mx5 nc owners before trying the trombone cleaner method. Thanks!
Yes. This is what I found to my amazement. I really need to do a full start to finish demo video at some point. Just my health isn’t the best at the moment
Even though I do not have a mezda I do enjoy the tutorials you do for it
Mazda 😂
You think I don’t watch these ! I was looking for that pad thought I was going mad !
Don’t know what your on about
Just seen this today June 11th 2023. Like you I took out the drain tubes to clean. I found very little on this but was motivated by the fact i kept getting water in the cabin. Well that and the fact my good lady decided to push a trombone down them and the noise inside the cabin was bad. As you say its relatively easy. I also found that the rubber seals were stiff and wouldnt seal properly. I inverted the seals and fix to problem. Thanks for showing this video
Thanks, I have been looking for someone to share their standard car so I can do a full guide from start to finish.
@@dss199 I have a hard top, just fixed the rattling on the roof by simple adjustment of the roof catch. I am not a mechanic by any description i bet there are many MX5's out there playing a tune. Be good if you had a video on that and my next project is rattling windows !
@@pensionpete57 sadly I have a softop, but am looking for someone near to help with so I can document procedures on both versions
@@dss199 I am in Newark Notts where are you?
@@pensionpete57 Tibshelf, Derbyshire
Great video , thanks. Would a jet of water ( if you could get in there ) help clean the drain hose ?
I tried something similar and it just moved more dirt deeper, also you have the risk of dislodging or damaging the pipe work / valves (later models)
Would of been nice to have a bit of a tutorial on how to remove the plastics to actually get at the drain tubes 👍
It’s something I am planning, my interior isn’t standard so hard to film the full video guide. But is something I am planning to film
I have a MX5 Roaster 2013 and I don't think I can use the Hood Drain Cleaning Brush method as it appears that a grill has been fitted at the top end of the draining hole stopping you from inserting a brush, unless you know how to remove this without breaking it.
Later models came with the kit fitted, the grille isn’t an issue, it’s a blue foam block at the top that may be causing you’re issue.
Great vid but I am curious to hear the difference between the before and after of the road noise, if it could be captured.
Hi. It’s really subjective. But I also didn’t have a recording of it before. But I can say it is really noticeable. If you can hear tyre and road noise from behind the hoops then this is most likely a cause.
Excellent. Now do my Mk4Recaro
I will do once it’s here
Thank you for taking the trouble to share this. Previously tried the trombone cleaner method, but really struggled to find the drain hole. Am having problems of excessive condensation inside my MX5 Mk3 - all carpets (inc. boot) are dry. The roof appears to be watertight. The car isn't kept in a garage and left on the drive in all the adverse elements ...perhaps that's an issue?
Hi. Thanks.
Sounds like it could be the roof drains or the windscreen scuttle grommets. Both are worth a check
@@dss199 Thank you. I checked and fixed scuttle grommets several years ago as water was getting into the footwell - these have remained dry ever since. Will certainly double check roof drains. I'll probably have another go at trying to find the rear drain holes for the trombone cleaner .... such an awkward angle. Thanks again.
@@sengwellb1 you need to start with the kick plates and remove. Then remove door side trim and seatbelt covers. Then you can remove the roll bar hoops covers. Then remove the large back plastic that holds the fuel cap pull, you will need to remove centre console to do this. Once that is done it’s a case of removing the seatbelt and cover allowing you access to where my video starts. Need to borrow a mk3 before I can film the full procedure. Also get some dehumidifier boxes and put them front footwell and behind seats.
@@sengwellb1 if you need more help let me know
@@dss199 thank you. Recently placed some dehumidifier boxes inside the car which have certainly collected water.
Great video. Is this just for the soft top model?
It should be the same for both I believe
It would appear the pipe work it’s the same but the roof section is different. So should be the same in principle
Maybe I should do this too. I usually use Air pressure to clean it, but I think one of the tubes could have become loose because of it...
Good luck, I am hoping to do a full from start to finish version of the video on a standard car. 👍
This is better than that other video, I also wasn’t clear on how you get the trims off to get to the seatbelt mechanism
Thanks, I plan to do a more in depth start to finish video, but as my car is not standard and has bits removed then it wouldn’t be as easy to follow. So I will need to borrow a car
@@dss199 come to Northumberland do mine and use for content…. Win win 🤣
@MrMazdaGuy Thank you for this video, i took my drains out and cleaned them and upon re-installing i found that they seem to leak in to the seat belt tensioner area (leak appears to be coming from above possibly from the point where the rubber black pipe connects to the drain box, assuming putting it back together as you have shows just by pushing it back on as flush as possible. Any idea what could be causing it to leak down into that area? also found my white plastic end part that exits out of the car, the seal is perished and causes water to drip down too inside the tensioner box, any help would be appreciated, thanks. Lloyd
Hmmm, curious. I haven’t had this to my knowledge. I know there is a foam seal on the bottom piece. It might not be sealing well?
I may have to investigate when I do some more work on my trim at some point
Another thought, you could try a thin layer of silicone if this is the case. I believe it’s the same type seal as the windscreen grommets that fail?
Hey. I have been informed that the seal around the base of the roof and the chassis under the window can be a leak source that runs down into the back of the footwell. Also there is a tank above the drain hose that can clog.
Just thought I would update you on what I have found incase you have the same problem.
Clean the pieces one by one and when I put them back I have a leak of water to the part where the seat belt is. It does not seal 100% the plastic piece vs. the metal of the bodywork and there it filters the water inside. How do I fix this problem?
Hi,
My car had never had them touched in that area but had water leak (before stripping) after striping mine went away and it didn’t leak anymore. Might be worth double checking and I have heard the seals on the top and bottom prices can perish, at that point it’s find a solution or buy new parts, I would personally double check that the ends are flush with the bulkheads if that makes sense. The slightest twist and they wouldn’t be
How did you get the sponges out? Remove all the trim under the top?
You remove them from the top, I did it from a half down roof position, but it will depend on you’re dexterity and hand size etc. if you need any more help feel free to send me an email, I think it’s public on here
I got lost within the first minute 🙈 Do I need to remove plastics etc first to access the seatbelt/plastic tray?
Yes, I already had them off to do the roll bar, I will have to rebuild the car and the strip it to do a video on that. As my video was more a discussion about doing a full clean vs trombone cleaner. Wish someone was closer to me who has a mk3 then I could clean their roof drains to get the footage 🤔
@@dss199 ahh brilliant mate thanks for explaining. Gives me something to do haha
@@FATPLEB if you start around the doors it’s easier so your scuff guards (for feet) and then the plastics that run up the side of the seat and seatbelt. Then removing the centre console. Then undo all the poppers and the tray should come off. I do have a time lapse of me doing the trim removal.
@@dss199 Can you post a link to the trim removal?
@@Paintppa1 I haven’t made it yet, I need a standard mk3 as mine is far from standard. Once I get someone to lend me a standard mk3 I will record the process
Regarding the road noise you hint at in this video. Would you describe it as loud/droney enough to consider it annoying. I have an awful drone coming from over my left should at anymore than 40mph. Maybe this is the cause.
Hi this sounds like it, it’s like having a amplified sound of the wheel arch behind your shoulder, sounds like you may have an inverted seal
@@dss199 I'll have a look after work tommorow. Been searching for a while for the cause of this noise. Hopefully this is it.
@@henrymarriott5636 I would make sure you plan extra time as it can be a bit if a pain. I do plan to do a full video on it once I can borrow a car to do it on
I have this same exact noise, did you have any luck in resolving the issue? Also what does having an inverted seal mean?
Where on the car is the little cave where the drain tubes live? Cheers..
A Google search will help make it easier, but I find it easier to partially lower the roof to find it.
@@dss199 Thanks, I'll have a look..
@@flannel2699 sorry I can’t post pictures on here. I am going to try and find a standard mk3 and do a more detailed video on it using the feedback from this video
@@dss199 Cool. Thanks..