All this guy needs to do is put a t splice to connect all the hoses instead he charges the customer most likely $60 or probably like $100 for a whole new part which isn't necessarily needed because the hoses looked pretty decent I hope he did not charge the customer for all the antifreeze that he wasted since he decided not to check the hoses from the start as he said
I normally don't reply to constructive criticism, however I am a little confused by your comment. You state all that is needed to perform this repair (properly?) is a "T" splice. If you notice, the customer had already put said "T" splice on the vehicle and it failed. The customer wanted the vehicle back to OE performance and reliability, so they were more than happy to pay for the factory replacement hose. The "charging the customer" statement implies that I am in someway taking advantage of the customer when there may be a cheaper route. This is never the case in any of my repairs and the customer has the last say so in what they will pay for. The next part of your comment involves charging the customer for wasted antifreeze. Not sure what you are talking about as the engine was filled with straight water for pressure testing purposes. You noticed that I said I failed to do a thorough visual inspection but failed to see the engine was filled with water. You can see why I take issue with this. The bottom line in this scenario is this engine could have been destroyed due to an inadequate repair as the engine overheated. The cost of a factory hose compared to a new engine is a non factor. I do appreciate you taking the time to watch and engage. I just want to say the just about every video out there has some behind the scenes goings on that are very difficult to convey on camera.
Hello can you please help me I have a bad fuel injection pressure sensor and I cannot find where it goes any tips would be highly appreciate it I have an 08 navigator base 5.4l
@@mrblackspook31 I still haven’t figured it out just been driving it like that if you find the problem please share some info it would be greatly appreciated
Quick connect/disconnects, so sweet! Well done sir. Thanks!
Can we use regular tap water?
All this guy needs to do is put a t splice to connect all the hoses instead he charges the customer most likely $60 or probably like $100 for a whole new part which isn't necessarily needed because the hoses looked pretty decent I hope he did not charge the customer for all the antifreeze that he wasted since he decided not to check the hoses from the start as he said
I normally don't reply to constructive criticism, however I am a little confused by your comment. You state all that is needed to perform this repair (properly?) is a "T" splice. If you notice, the customer had already put said "T" splice on the vehicle and it failed. The customer wanted the vehicle back to OE performance and reliability, so they were more than happy to pay for the factory replacement hose. The "charging the customer" statement implies that I am in someway taking advantage of the customer when there may be a cheaper route. This is never the case in any of my repairs and the customer has the last say so in what they will pay for.
The next part of your comment involves charging the customer for wasted antifreeze. Not sure what you are talking about as the engine was filled with straight water for pressure testing purposes. You noticed that I said I failed to do a thorough visual inspection but failed to see the engine was filled with water. You can see why I take issue with this. The bottom line in this scenario is this engine could have been destroyed due to an inadequate repair as the engine overheated. The cost of a factory hose compared to a new engine is a non factor.
I do appreciate you taking the time to watch and engage. I just want to say the just about every video out there has some behind the scenes goings on that are very difficult to convey on camera.
Hello can you please help me I have a bad fuel injection pressure sensor and I cannot find where it goes any tips would be highly appreciate it I have an 08 navigator base 5.4l
My 2008 do the same thing like not taking the gas.
@@mrblackspook31 I still haven’t figured it out just been driving it like that if you find the problem please share some info it would be greatly appreciated
Sometimes when I play with my wire harness it clears out. Or it could be one of the coil pack wires.
@@mrblackspook31 I’ll look into it thank you
Hi
MYIN OR HETS BAD AND ISNAT .THE WATORPAMP IS THEIS .COS IM MISIN APES.👍