This guy is seriously underappreciated, the silent explination makes it so you dont get any of the confusing welder speak and its very straight to the point!
Excelente tutorial maestro , muy buenos consejos y mejores demostraciones , gracias por compartir tanta información y conocimientos , un saludo cordial y por supuesto un gran like desde Narón,Galicia (España) 🤓 🛠️
Thank you for sharing this method Hagojibi! When you set the rod "in the joint" can you share, is the electrode pointed at the end of the rod, a little up the rod, or is the electrode pointed at the pipe? I tried this method, and ended up sparking and spitting and balling the rod -lots of excitement, but not good result :D Very much appreciate your thoughts!
Welding thick wall tubing is not the test. Try .035" or .028" thin wall 4130 aircraft structural tubing if you like frustration. Practice and patience are the key, along with the correct and size filler rod. Try using ER309L 1/16 filler rod for more control on your stainless.
Can you show us dual welding with stainless steel? It’s very common in tank fabrication. I dont think I’ve ever seen a video on it and it would be helpful to people new to the trade.
Your videos are terrific. I have had an everlast ext 255 for about 2 years, very little tig time, and very mixed results. Tig is for entertainment, I mostly use this for stick. I watch plenty of tig instructional videos. Yours are ⭐⭐⭐⭐⭐ If you could do any videos with this prossess called cold welding, so i could under stand what is going on. Its like it is somekind of hocus pokeus.
Cold welding is A JOKE. Unless you need to weld two razor blades together, a cold welder has no purpose in this world. Cold welders do not make a strong weld. Chinese JUNK
Вариться очень легко, но только с поддувом. Я котлы делаю, горловину толщиной 0.7 мм привариваю к 1.5мм без проблем! Но везде с поддувом ! Шлака и каши нет, ни с одной стороны.
@@Kulak-223 а если это перила или огорождение? Поддув тут не катит. И как бороться с короблением? Фиксация труб не особо помогает. Какая техника сварки, порядок существует?
@@СергейРаков-п2т Перила так же можно задуть . Сделать в нужных местах пробки . Лишние стыки заклеить скотчем бумажным. Варите в разбег. Да, будет дороже. Но тут вам выбирать, качество или скорость , деньги... Или пользуйтесь его методом.
here's a tip. if your puddle is running away from you so much its leaving a hole. keep adding filler and moving forward, draw the heat out and cool with filler rod. I weld aluminum 18ga with gaps and don't burn through, 1/16- 3/32 inch gaps that is!
Perfect video , but I do miss your commentary . Why not run a high pulse with a low background current and a slow time so the arc can stay lit and keep the work illuminated , ?
I have done this and it works. No need for an HF arc start for each pulse. If background current is low enough, the puddle can solidify and the workpiece can cool a little between high pulses. However you need to have very low background current for small/thin pieces, and some welders cannot provide background current that is low enough. Also I would want to make sure I had enough penetration. The hammer-flattening of the tube end was a neat idea!
안녕하세요 weld님 궁금한게 있습니다. 사실 노가다나 중장비, 목수 같은일을 들어보면 하는 일을 안 알려주고 자기지인에게만 알려주거나 자기 밑에서 몇년동안 무급으로 일하는 사람들에게 조금씩 알려준다고 들었습니다. 근데 이렇게 유튜브로 공개적인 장소에서 다른 사람들에게 알려주시는 모습이 대단하시고 존경스러운데요. Weld님은 다른 사람이 이런 기술을 배워서 자기자신은 자리를 뺏는다는 걱정이 없으신지 궁금합니다. 그리고 youtube를 시작하게 된 계기가 남들에게 이런 기술을 알려주기 위함인가요?
그게 기술이죠. 아는거 아낌없이 가르쳐도 내가 더 잘할 수 있는 자신감 설령 잘 따라와 나보다 더 잘 해준다면 고마운일이죠. 쉴수 있으니 ㅎㅎ 해보시면 알겠지만 기술이란건 알고도 못합니다. 괜히 어설픈 넘들이 어깨 넘어로 배운거 가지고 가오 떨지만 찐 만나면 바로 깨갱입니다.
Uh, I try to avoid gaps. (Need all the help I can get.) Easiest way to get a no-gap fit is to use a milling machine, like I did recently while welding some 4130 tubing. I’d never done that kind of a joint before, and am a bit surprised it actually worked out passably. Still, though - this is useful, *like when you can’t get the good fitups.*
Oh, come back when you have understood that he was actually making a point by intentionally cutting the edge off. The video will become educational for you, when you are ready for it. ;-)
![weld [HAGOJIBI]](http://yt3.ggpht.com/ytc/AIdro_lButtTy6bwshHHOdUuuc7ktsddm0YgRj2FhqoPUm3aQA=s48-c-k-c0x00ffffff-no-rj)
This guy is seriously underappreciated, the silent explination makes it so you dont get any of the confusing welder speak and its very straight to the point!
I can use every bit of what I just saw imediately. Thanks
오늘도 좋은 용접 방법 감사드립니다.
다음영상도 기대하겠습니다. ^^
If only every problem could be fixed so easily by a deft hammer blow. Love your channel!
Die Besten Schweisstipps die ich kenne 🤗
Magic hammer!) Hit just anything with it and thing will fit to everything!))
Guten Morgen! Danke für die Videos.😀
Nice Welding 👍 nice workflow
"just as I lost my freedom when I got a wife..." hahahahahah
Jesteś moim nauczycielem . Dziękuję.You are my teacher. Thank you.
Brilliant!! Thank you !!
Хорошее и доходчивое объяснение. 👏👏
Сильно напоминает когда я варил газосваркой, много общего.
I enjoyed watching
Excelente tutorial maestro , muy buenos consejos y mejores demostraciones , gracias por compartir tanta información y conocimientos , un saludo cordial y por supuesto un gran like desde Narón,Galicia (España) 🤓 🛠️
Desde España, ¡Muchas gracias por tus vídeos!
7:28
"If you gain something, you lose something. Just as I lost my freedom when I got a wife..."
That's the point of this welding video. Awesome! 🤣🤣
Thenk you my brother im turkey
명언제조기시네 ㅋㅋ 감사합니다
Super instructif,super vidéo très explicite .en fait vous êtes le meilleur
Super! Thanks a lot!
Parabéns pelo seu desempenho seus vídeos me incentivou muito a soldar com a tig
Sprzęt do precyzyjnych prac,piękne wykonanie -Brawo..
Nice bro
팁 감사합니다 항상 많이 배우고 갑니다 ㅎ
Thank you for sharing this method Hagojibi! When you set the rod "in the joint" can you share, is the electrode pointed at the end of the rod, a little up the rod, or is the electrode pointed at the pipe? I tried this method, and ended up sparking and spitting and balling the rod -lots of excitement, but not good result :D Very much appreciate your thoughts!
Awesome, as usual. Thank you Master. Don't blame yourself in case of wife (if translation is correct). Sometimes wives can be kinda good 😆
The smash the end trick, 🤯 mind blown! I feel dumb lol. Been notching tube for years without even considering that option. Good stuff my guy!
Maybe because it looks not as good and might also induce a weak spot?
Obrigado pelos ensinamentos, Santa Catarina, Brasil.🇧🇷🇧🇷🇧🇷
좋은 아이디어 김사합니다
Welding thick wall tubing is not the test. Try .035" or .028" thin wall 4130 aircraft structural tubing if you like frustration.
Practice and patience are the key, along with the correct and size filler rod.
Try using ER309L 1/16 filler rod for more control on your stainless.
Gracias !!! 🇦🇷
Come sempre molto interessante.
Ottimi consigli ✌️
Can you show us dual welding with stainless steel? It’s very common in tank fabrication. I dont think I’ve ever seen a video on it and it would be helpful to people new to the trade.
Very helpful video!
What´s the thicknes of the tungsten electrode you have used to weld these pipes?
Ótimo vídeo parabéns 👏👏👏👏
Sempre uma aula espetacular.
잘보고 있습니다
Ну про жену в конце конечно круто сказано))
Thank you.
Parabéns, sou do Brasil
Teria como dublar seus vídeos, você é especialista em solda tig, Good job
Oi, ativa a tecla cc e escolhe o idioma portugues a tradução está perfeita. Essa tecla fica na parte superior do video apertando os 3 pontinhos.
@@anailtonprocopio9174 obrigado brother.
Exelente ahora con tubo de aluminio. Saludos
Меня смущает тощина этих трубок. На ролике что то не похоже на тонкостенные?
Your videos are terrific. I have had an everlast ext 255 for about 2 years, very little tig time, and very mixed results. Tig is for entertainment, I mostly use this for stick.
I watch plenty of tig instructional videos. Yours are ⭐⭐⭐⭐⭐
If you could do any videos with this prossess called cold welding, so i could under stand what is going on. Its like it is somekind of hocus pokeus.
In cold welding one high amperages for very short intervalls. The welds are usually not fused correctly because of that.
Cold welding is A JOKE. Unless you need to weld two razor blades together, a cold welder has no purpose in this world. Cold welders do not make a strong weld. Chinese JUNK
Ho saldato proprio ieri lo stesso tubo inox sottile🎉
Boss man
Super sposoby
А как вы свариваете трубы где толщина стенки 1.0 или 1,5 мм ? И как избежать коробления труб в месте сварки?
Вариться очень легко, но только с поддувом.
Я котлы делаю, горловину толщиной 0.7 мм привариваю к 1.5мм без проблем! Но везде с поддувом ! Шлака и каши нет, ни с одной стороны.
@@Kulak-223 а если это перила или огорождение? Поддув тут не катит. И как бороться с короблением? Фиксация труб не особо помогает. Какая техника сварки, порядок существует?
@@СергейРаков-п2т
Перила так же можно задуть . Сделать в нужных местах пробки .
Лишние стыки заклеить скотчем бумажным. Варите в разбег. Да, будет дороже. Но тут вам выбирать, качество или скорость , деньги...
Или пользуйтесь его методом.
Вносите минимум нагрева, будет меньше коробить.
Good advice, I miss your voice over
목소리 듣고 싶어요~~~
the BOSS
🤣😂🤣😂🤣😂🤣
So true.
Salve salve mestre
here's a tip. if your puddle is running away from you so much its leaving a hole. keep adding filler and moving forward, draw the heat out and cool with filler rod. I weld aluminum 18ga with gaps and don't burn through, 1/16- 3/32 inch gaps that is!
What welding machine are you using?
👍👍
Perfect video , but I do miss your commentary . Why not run a high pulse with a low background current and a slow time so the arc can stay lit and keep the work illuminated , ?
I have done this and it works. No need for an HF arc start for each pulse. If background current is low enough, the puddle can solidify and the workpiece can cool a little between high pulses. However you need to have very low background current for small/thin pieces, and some welders cannot provide background current that is low enough. Also I would want to make sure I had enough penetration. The hammer-flattening of the tube end was a neat idea!
@@benz-share9058 take a look at farm gates and school chairs . They have been flattening tube for welding forever . But it is handy .
Well I heard there is a method to cover ones butt if you get a blow through on thin pipe. Do you know the procedure for repairing the hole?
ㅋㅋㅋㅋ마지막 자막,,,,,,마누라를 얻으면 자유를 잃,,,,,,, 많은 울림이 있는 유익한 팁 영상이였습니다~!!
파이프 말씀하실때 스케줄은 무슨 수치죠?
스케줄은 파이프외경 치수를 통틀어 부르는 용어입니다 규격
Какой лучший TIG-COLD аппарат микро тиг сварки с 0,001 с сварки?
مرحبا انا اعمل في صناعة الآفران الخبز ومحامص البزر وعندي خبرة في لحام الارجون كيف فيني اقدم على طلب عمل يا ريت تساعدني لو سمحت رد علي
무엇보다 자재 준비 하는거 시간많이 뺏기는데 세심하게 준비 하고 촬영하고 편집하고
열정과 정성에 칭찬하게 됩니다
👍
Hola: como se puede soldar una hoja de sierra sinfin o sierra de cinta para carpintería?
Как сварить тонькую,0.35мм нержавейкую, не могли бы показать,зараннее благодарю,напоминаю аппарат у меня без импульса
How's your voice?
NIESAMOWITE
안녕하세요 weld님 궁금한게 있습니다. 사실 노가다나 중장비, 목수 같은일을 들어보면 하는 일을 안 알려주고 자기지인에게만 알려주거나 자기 밑에서 몇년동안 무급으로 일하는 사람들에게 조금씩 알려준다고 들었습니다. 근데 이렇게 유튜브로 공개적인 장소에서 다른 사람들에게 알려주시는 모습이 대단하시고 존경스러운데요. Weld님은 다른 사람이 이런 기술을 배워서 자기자신은 자리를 뺏는다는 걱정이 없으신지 궁금합니다. 그리고 youtube를 시작하게 된 계기가 남들에게 이런 기술을 알려주기 위함인가요?
그게 기술이죠.
아는거 아낌없이 가르쳐도
내가 더 잘할 수 있는 자신감
설령 잘 따라와 나보다 더 잘 해준다면
고마운일이죠. 쉴수 있으니 ㅎㅎ
해보시면 알겠지만 기술이란건
알고도 못합니다.
괜히 어설픈 넘들이 어깨 넘어로
배운거 가지고 가오 떨지만
찐 만나면 바로 깨갱입니다.
Мастер, здравствуйте !
Я и в такие трубки подаю аргон.
С поддувом проще сваривать!
В трубку подал 3-4л газа, на сбросе отверстие 3мм.
да и давить нужно более на целую стенку, а не на край :)такой зазор это мелочь.
@@anastasiakhoma5801
Согласен.
Как сказал мой учитель . - Закатать можно и дверной проем !
Что делать с деформацией, трубки гнутся
Сколько такой сварочный аппарат стоит?
「妻と結婚してミリベルダーゼを失ったように」😂😂😂😂これは良かった
А нельзя заварит холодной сваркой. ?
En mexico al corte que hiciste le llamamos boca de pez
Uh, I try to avoid gaps. (Need all the help I can get.)
Easiest way to get a no-gap fit is to use a milling machine, like I did recently while welding some 4130 tubing. I’d never done that kind of a joint before, and am a bit surprised it actually worked out passably.
Still, though - this is useful, *like when you can’t get the good fitups.*
Лучше покажи сварку обратным ходом это когда дуга впереди а пруток с зади идет))).
당신은 너무 재미있다
Тиг сварка как варит ясно,а вот параметры какие там установили.
Las tuberias son pequeñas pero no son delgadas
У нас это называется Рыбкой
정말 유익한 정보.
마누라를 얻으면 자유를 잃는다.ㅋㅋ
tig
Thin pipe to me is .015 or .020 that looks to to be close to .045
Haha lost your freedom when you got your wife
얻는것이 있으면, 잃는것도 있다....마누라를 얻으면 자유를 잃듯이..........
말이 발 뒷굽으로 제 명치를 후려치고 가네요...
마누라를 얻으면 자유를 잃듯이 ~ 감사
마누라를 얻으면 자유를 잃는다 명심하겟읍니다
Sr파이프 용접 죽어나요
3 thu thuat han mic that tot
Я бы грел сам пруток и капал на трубки
AH HINDI KALANG MARUNONG MAGTAPAL NG BUTAS PAG HINDI DIKIT ANG STAINLESS PIPE
зачеееем!!
I learned absolutely nothing.
有了老婆失去自由
Променял свободу на бесплатныи секс
Kusura bakmada kaynakçılıgın zayıf
벙어리임? 왜 말을못해?
lol
Technology is bad enough
Wrong torch angle, so you just cut off the edge angle with an arc. Like for the effort. And the video is not educational at all.😉
Oh, come back when you have understood that he was actually making a point by intentionally cutting the edge off. The video will become educational for you, when you are ready for it. ;-)