Thanks for the tip on waiting a bit to form the "swirls" in that Total Boat. So far I've only done small projects like Lazy Susans, using Alumilite at only about 1/8" deep pours, so the pigment settling hasn't been a concern for me.....but I'm planning on doing a larger project with a 1/2" single pour in a built form, so I'm glad I watched and found out about the settling....if it weren't for you, I wouldn't have known to watch out for that potential problem!!! Thanks!
Man that's absolutely impressive. My question is are the LEDs under the table? Have you ever seen anyone plumb the tables out so they can actually have them inside it? I was thinking of building a table with the ability to have USB and HDMI plugs in it, or some sort of wire/cabling management.
Nice table. I do river tables also. I noticed you didn't do a seal coat on the river edge, octagons, or the top. With Total Boat that isn't needed? I typically use Stonecoat. I get good result but I have to seal coat everything to stop air bubbles from escaping the raw wood while it sets up. Again, nice job.
So normally I do a seal coat especially if it's going to be with clear epoxy.. as like you said air will come out into the epoxy from the edges. And that is a big problem at times. With the Deep set epoxy from totalboat in the color it is not much of an issue that I have found. For the top I was going to be doing multiple coats of the totalboat table top. So the first coat acts as a seal coat anyway. If you would like to give totalboat a try I'll also drop a link for you to use and it will allow you to get a discount from them as well using the link if you want to give those guys a try I love their product been using it for a long time. totalboat.refr.cc/jeremyp
@@jpaynewoodworking7510 One other question. How long do you wait until you buff out the epoxy. The brand I mentioned earlier recommends 30 days cure time before buffing.
Wet sanding reduces the number of deep scratches. The water helps to clear debris from the sand paper as it cuts. Dry sanding will be more likely to build up residue ans cause deep unwanted scratches that will not buff out.
That was really cool and really informative. Nice video. And what would you charge to have one of those made? I would be interested in getting one made but just need a rough estimate on the price. I know it would depend on wood and all the technicalities of it but just a starting price I guess is what I'm after. Thank you and of it would be easier for you I can give you my email and we can figure it out through that if thats easier for you. Thanks again
funny and nice vid but im trying to learn how to add the LED lights.. yall need to stop misleading people with your titles if you're not going to show how you added the LED'S .. kmt
The led in this one are attached under the desk. It's not misleading. I don't put the leds I. The epoxy bc eventually they will go out and need to be replaced
Just pouring a finish layer does not ensure perfect flatness yes the epoxy will self level but there is almost always some very small high and low spots as well as wetsanding and then buffing will remove any dudt particles in the later you just poured. Thanks for watching
Went to the desk frame website, very cool. This will be my next project, except I will be making my River desk with walnut. BTw, yours looks great
Great Job! Nailed it 👍
Wow!! 😃That's such a BEAUTIFUL Wood Resin Gaming Desk!! 😃 Great job, Jeremy!! 😃
Fantastic piece of wood
Thanks for the tip on waiting a bit to form the "swirls" in that Total Boat. So far I've only done small projects like Lazy Susans, using Alumilite at only about 1/8" deep pours, so the pigment settling hasn't been a concern for me.....but I'm planning on doing a larger project with a 1/2" single pour in a built form, so I'm glad I watched and found out about the settling....if it weren't for you, I wouldn't have known to watch out for that potential problem!!! Thanks!
I would like just the desktop made with yellow and black
very nice, this video was just amazing 🙃👍
Great vid man and great desk!
Super sick desk. About to try my hand at my first desk build and this video gave me some great ideas. TY.
Great work!
Beautiful piece!
Man that's absolutely impressive. My question is are the LEDs under the table? Have you ever seen anyone plumb the tables out so they can actually have them inside it? I was thinking of building a table with the ability to have USB and HDMI plugs in it, or some sort of wire/cabling management.
Love it! I'm gonna make one. You've inspired me.
Very nice desk! Good name too!
Thank you
Thank you for sharing! Awesome to see you using the DIY kit as a part of this great work. Dropped a like already
Beautiful love the color and grain in wood
Thank you
Wonderful work and thanks for the play by play of the process. Gets my gears turning for making my own one day!
Love it!
Very nice production (video & table project) very well done! Nice to see such craftsmanship and attention to detail. Thoroughly enjoyed it! 👍👍
Thank you
Beautiful..
Thank you
I had subscribed after finding your channel. I absolutely love your channel great job and thank you so much for sharing. 👍
Thank you
awesome design and work. I think the idea of LED lighting got tossed haha
Naw there installed on the underside iv never cared fro them installed in the epoxy itself
AWESOME! I bought a set of the Business Edition legs last years for this exact sort of project!
Nice
Nice table. I do river tables also. I noticed you didn't do a seal coat on the river edge, octagons, or the top. With Total Boat that isn't needed? I typically use Stonecoat. I get good result but I have to seal coat everything to stop air bubbles from escaping the raw wood while it sets up. Again, nice job.
So normally I do a seal coat especially if it's going to be with clear epoxy.. as like you said air will come out into the epoxy from the edges. And that is a big problem at times. With the Deep set epoxy from totalboat in the color it is not much of an issue that I have found. For the top I was going to be doing multiple coats of the totalboat table top. So the first coat acts as a seal coat anyway. If you would like to give totalboat a try I'll also drop a link for you to use and it will allow you to get a discount from them as well using the link if you want to give those guys a try I love their product been using it for a long time.
totalboat.refr.cc/jeremyp
@@jpaynewoodworking7510 Thanks for the info. I may give them a try. I'll use the link, save some money and get you some love from Totalboat.
Thank you
@@jpaynewoodworking7510 One other question. How long do you wait until you buff out the epoxy. The brand I mentioned earlier recommends 30 days cure time before buffing.
@@gjhard101 I buffed the total boat table top after about a week
hahhahaha. The wizard of oz part. hahahahahaha.
So, a year later. . .how's the epoxy surface wearing? I'm contemplating a resin desktop but am concerned about how it'll hold up under use.
Good question
Fascinating! Thanks.
Thank you
Is it expensive to do this?
How much for the table and shipping to Washington state?
Hey i am in tacoma and can build you one of these
I would love to buy one of this from you, let me know if it is possible?
How much did it cost you to make it?
Subbed
Very nice. Do more videos like this. Im saving up to do my floating L shaped desk i built.
Thank you. And that sounds like a fun build
loved it except your maths where you calculated volume of pour
Been a pretty accurate system so far lol. But I'm sure there are more accurate ways.
I got a question... What cnc machine do you use?
Cool
why wet sand over dry sanding ?
Wet sanding reduces the number of deep scratches. The water helps to clear debris from the sand paper as it cuts. Dry sanding will be more likely to build up residue ans cause deep unwanted scratches that will not buff out.
@@jpaynewoodworking7510 Thanks. !
so you did NOT seal the bottom ?? or you did ??
Yes the bottom is sealed
@@jpaynewoodworking7510 what does he mean "seal the bottom"?
gj bro!!
Thank you
That was really cool and really informative. Nice video. And what would you charge to have one of those made? I would be interested in getting one made but just need a rough estimate on the price. I know it would depend on wood and all the technicalities of it but just a starting price I guess is what I'm after. Thank you and of it would be easier for you I can give you my email and we can figure it out through that if thats easier for you. Thanks again
Size of the desk
??
This one is 24 by 50
@@jpaynewoodworking7510 ty
Price?
These would be around $3000 shipped in the US.
Can u gimme a cnc router homie?
I need a wood epoxy desktop computer... has anyone done that? I would pay 10-15k ...
I make them custom for people. Feel free to email me at jeremy@jpaynewoodworking.com
like the case of the computer? instead of metal?
Dude I just learned people sell these for like 10 grand
Ha ha yea they are a ton of work I'd like to make more of them
funny and nice vid but im trying to learn how to add the LED lights.. yall need to stop misleading people with your titles if you're not going to show how you added the LED'S .. kmt
The led in this one are attached under the desk. It's not misleading. I don't put the leds I. The epoxy bc eventually they will go out and need to be replaced
Quit sanding the damn epoxy tables! Just pour a thin finish coat and it will be as clear as can be.
Just pouring a finish layer does not ensure perfect flatness yes the epoxy will self level but there is almost always some very small high and low spots as well as wetsanding and then buffing will remove any dudt particles in the later you just poured. Thanks for watching