Myer! Just when I thought I would only see you in content from PDD & HorseTorques 👍🏼. Nice work man! I enjoy your work/knowledge on video. Keep at it man!
I remember you can change the solenoid without removing the valve body. I replaced the solenoid 3 times on my 46re and I know the 46/47/48re transmissions all have the same valve body design other than the 68rfe which is different.
Greetings, awesome advice. I have a 2006 3500 Dodge Ram with a 48re. This video is very informative, is there a way to clean the system before installing the new parts? I have heard of other people putting in the new parts and having issues a few weeks later. Please keep sharing these awesome tech videos!
I have a 04 has p2509 and a p3500 . Have tried sending off ecm checked out good. Checked most grounds .anyways starts rough shuts off when in gear and 2nd will straight kill it .found that disconnecting overdrive solenoids ignition on will run fine until u shift it in key on engine off starts like resetting ecm .checked key on hot wires are just dropping on and off .ever had this issue looking to replace the solenoids next
Hi I wonder if you could give me some advice I’ve got a 2003 2500 Cummins in the uk and I’m having trouble with the trans on the dash the gear indicator only shows P and N then the truck feels like it’s pulling away in top gear if I shut the engine off and restart it a couple of times it highlights D and away it goes I’ve tried changing the neutral safety switch range sensor and today after watching you video I changed the pressure sensor but has made no difference have you ever heard of this problem or can give me some advice it would be greatly appropriated thanks
I have a 97 dodge ram 5.9 cummins my problem is that my 2nd gear doesn't shift properly could it be the governer solenoid or should the bands need to be adjusted....any idea
Ive always heard Josh saying something about you being from Missouri. Just curious as what part you were from. Keep up the good content man! Love the channel!
See im thinking this is my issue also but i cant get my 04 to go into any lower gears no matter what i try so im hoping this still fices it because when i bought the truck the tranny was stamped woth rebuild markings that were one month old when i bought the truck so im hoping when the heat exchanger went bad it took out the governor pressure solenoid and transducer and thats all but coolant never got into the tranny at all instead the tranny fluid pushed into the coolant and it got shut off for good when it happened and when i flushed the tranny lines and cooler and changed the filter and etc there was no sign of coolant at all it was just good red fluid but the coolant system was loaded with trans fluid lol it was fun flushing out lol❤❤❤
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
Mer I didn’t know you had a channel! I see you a lot on Josh’s channel. But I am glad to be a part of it now. Hope to learn a lot. Adrian
Thanks for your clear step by step coverage. I have watched a few but seems some details are always missing; you filled in the gaps perfectly!
Great video with very clear instructions, appreciate mentioning the right socket sizes, etc.
Awesome Stuff!!! Just found your channel!! This is great, exactly the video i was looking for! Keep it up!
Mer you have some great builds. Thanks for sharing your knowledge it’s appreciated.
Myer! Just when I thought I would only see you in content from PDD & HorseTorques 👍🏼. Nice work man! I enjoy your work/knowledge on video. Keep at it man!
Nice job Myer..! Keep the content coming... love the videos on these trucks
I remember you can change the solenoid without removing the valve body. I replaced the solenoid 3 times on my 46re and I know the 46/47/48re transmissions all have the same valve body design other than the 68rfe which is different.
I hate the park rod. That piece has been my biggest battle every time I put the valve body back in.
New sub via Horsetorques.
Let's crank this channel up!
👍💪
Greetings, awesome advice. I have a 2006 3500 Dodge Ram with a 48re. This video is very informative, is there a way to clean the system before installing the new parts? I have heard of other people putting in the new parts and having issues a few weeks later. Please keep sharing these awesome tech videos!
How did I just now find this channel? Your boy horsetorques should of sent me here long ago
How much play you like to have on the band apply levers?
Please Sir, May I have more!?
Amazing video ❤
I have a 04 has p2509 and a p3500 . Have tried sending off ecm checked out good. Checked most grounds .anyways starts rough shuts off when in gear and 2nd will straight kill it .found that disconnecting overdrive solenoids ignition on will run fine until u shift it in key on engine off starts like resetting ecm .checked key on hot wires are just dropping on and off .ever had this issue looking to replace the solenoids next
Hi I wonder if you could give me some advice I’ve got a 2003 2500 Cummins in the uk and I’m having trouble with the trans on the dash the gear indicator only shows P and N then the truck feels like it’s pulling away in top gear if I shut the engine off and restart it a couple of times it highlights D and away it goes I’ve tried changing the neutral safety switch range sensor and today after watching you video I changed the pressure sensor but has made no difference have you ever heard of this problem or can give me some advice it would be greatly appropriated thanks
Always change the filter if you drop the pan. Regardless of miles.
When doing this what gear do you have to be in
Do you have a vid for a 1999 3500 shift solenoid replacement vid?
Hey man I’ve got a question, my 04 cummins takes a while for 1st and sometiems 2nd gesr to get in
I have a 97 dodge ram 5.9 cummins my problem is that my 2nd gear doesn't shift properly could it be the governer solenoid or should the bands need to be adjusted....any idea
Can we get a video on the rack swap on the 2nd gen!
Could this sensor cause the transmission not to go into overdrive when it’s cold out?
Ive always heard Josh saying something about you being from Missouri. Just curious as what part you were from. Keep up the good content man! Love the channel!
I'm from Annapolis MO. I'm actually here right now visiting family.
Small world, I live in the Farmington area. Even cooler watching a local guy lol
Merrrr why did you stop uploading videos 😢
here's a question that can't be answered, p1781 on 42le , 99 chrysler 300 m, i know the code says OD pressure switch, so how do you fix that.
See im thinking this is my issue also but i cant get my 04 to go into any lower gears no matter what i try so im hoping this still fices it because when i bought the truck the tranny was stamped woth rebuild markings that were one month old when i bought the truck so im hoping when the heat exchanger went bad it took out the governor pressure solenoid and transducer and thats all but coolant never got into the tranny at all instead the tranny fluid pushed into the coolant and it got shut off for good when it happened and when i flushed the tranny lines and cooler and changed the filter and etc there was no sign of coolant at all it was just good red fluid but the coolant system was loaded with trans fluid lol it was fun flushing out lol❤❤❤
🔥🔥🔥
👍🏻👍🏻
Thank you!