Just got 3 120mm no lcd for my top mount rad fans. And 1 140mm with lcd rear exhaust. They look so good. In US the 120mm 3 pack with controller with $109.99, the 1 140mm was $50. Total $160. They bustin heads for the reverse blades bruh
I need help I had all reverse fans and I swapped 1 part of the reverse with normal fans but they’re deff showing the lcd screen but no rgb? How’s that possible
no..u need to follow the trouble shooting steps exactly I only has issues cu I didn't understand how to use them and I was using so many udb 9pin devices u need to make sure you plug the hub directly to the 9pin on the motherboard and use ports 2 3 or 4 on the hub wen u connect the fan ..and then update app software and it will work
so i got the 3 pack of the 120mm reverse blades but the L-connect software only recognizes two displays. I plugged them into port two, tried to rearrange them, tried to reinstall the software but no matter what, the 3rd display (the one furthest away from the cable) wont work. Do you have any ideas how to fix or do i have to return them?
ye sometimes u can use too many connections on a splitter regardless of the hub, and for these lian li fans they need to have a direct connection to the motherboard and if u use a hub splitter you can only plug so many connectors to it for it to work, i also learnt the hard way but finally figured it out with some troubleshooting and help from lian li , without lian li pointing this out no one would get it , especially wen your running more 9pin devices @@TheBonecrusherz
I have a problem, I can't update the firmware as it gives me a network error, and the fans are not detected by the lconnect 3 software...the currently installed version is tl controller 0.51...any solution?
u may need to contact them either on Facebook or directly. they will give u better insight to this... I honestly followed their troubleshootingnsteps correctly and that's it it was done... no more issues works everytime ..and if ever there is a glitch with any sensors ..justva simple reset and it's solved
@@MIKEYZVLOGZ The problem is that when I go to settings and check updates the software gives me a network error. I try to disable firewall but it doesn't change. You should find an alternative procedure to update your controller.
in order to control the lcd u will need the hub ... that's the only want to customise the lcd to display what u want... it reads via the 9pin usb cable from hub... let me test it for u without the hub..but I'm pretty sure u need the hub...ok I've confirmed u can't control lcd screen unless u have the hub .. if u don't care for lcd display then get non lcd tl fans and u can just connect using the leds
did u follow the trouble shooting steps?? did u reset the pc after making changes? have you connected all the cables 6pin pcie, sata , 9pin usb 2,0 directly to mobo and used ports 2 3 or 4 on hub ?
@@glizzymob7294 hmm thats very strange , u may need to contact them and ask for more advice, as i only followed their troubleshooting steps and it was a success
what's wrong... the display stuck on logo ? or one of them not working ? how many are on and most importantly make sure u update all firmware first and download latest version of software
once u update latest fw and sw make sure u plug in the sata cable and the usb 9pin into the motherboard directly..now also plug in the cable into hub but choose either port 2 3 or 4 on the hub...do not use port 1 on hub ..it won't work
I have 7 of these in my case. They're amazing!
@@ral8031 he'll ye
I wish I could afford them
Just got 3 120mm no lcd for my top mount rad fans. And 1 140mm with lcd rear exhaust. They look so good. In US the 120mm 3 pack with controller with $109.99, the 1 140mm was $50. Total $160. They bustin heads for the reverse blades bruh
try create a loger gif anim,u'd love it.
I need help I had all reverse fans and I swapped 1 part of the reverse with normal fans but they’re deff showing the lcd screen but no rgb? How’s that possible
so nice...like your cute furry friend on your lcd screen 😂
i cant even afford the normal sl140 let alone the sl120 😅nice content though man
I know right
@@MIKEYZVLOGZ Update: I am getting SL120 v2! I am going to update you how it goes in the end 😂
Very well done
thanks my friend
Have you had any problems with the sensor screen glitching out when on sensor mode. This only happens with the sensors and nothing else
no..u need to follow the trouble shooting steps exactly I only has issues cu I didn't understand how to use them and I was using so many udb 9pin devices
u need to make sure you plug the hub directly to the 9pin on the motherboard and use ports 2 3 or 4 on the hub wen u connect the fan ..and then update app software and it will work
I did a short explaining this
@@MIKEYZVLOGZ is it this video???
I have 6 120 non lcd and 3 120 lcd. Was not cheap at all
trust me I know
so.. do you need the controller hub for any amount of these fans? i.e even if you bought 1 fan or 2
yes because only with the controller hub can u control the lcd and what it displays... without it all u will see only the lian li logo
@@MIKEYZVLOGZ ah ok thank you. Can't decide if it worth the investment or not lol
@Zombie101 ye its not for the faint of heart its exspensive
@@MIKEYZVLOGZ but is it worth the cash or not really
@@MIKEYZVLOGZ is it worth the cash or not really¿
so i got the 3 pack of the 120mm reverse blades but the L-connect software only recognizes two displays. I plugged them into port two, tried to rearrange them, tried to reinstall the software but no matter what, the 3rd display (the one furthest away from the cable) wont work. Do you have any ideas how to fix or do i have to return them?
ok are u using a port right off the mobo? and also try port 3 or 4
@MIKEYZVLOGZ I was using the nzxt usb hub, apparently that was the issue. Thanks a lot for your help 🫡
ye sometimes u can use too many connections on a splitter regardless of the hub, and for these lian li fans they need to have a direct connection to the motherboard and if u use a hub splitter you can only plug so many connectors to it for it to work, i also learnt the hard way but finally figured it out with some troubleshooting and help from lian li , without lian li pointing this out no one would get it , especially wen your running more 9pin devices @@TheBonecrusherz
really happy you finally got it to work
Very late but it downloads but once it does it’s thing it does not work
I. not sure what ur saying pls be clear and I can help u best I can
I have a problem, I can't update the firmware as it gives me a network error, and the fans are not detected by the lconnect 3 software...the currently installed version is tl controller 0.51...any solution?
u may need to contact them either on Facebook or directly. they will give u better insight to this... I honestly followed their troubleshootingnsteps correctly and that's it it was done... no more issues works everytime ..and if ever there is a glitch with any sensors ..justva simple reset and it's solved
connect each fan separately and update the firmware to latest for each fan individually ..
@@MIKEYZVLOGZ The problem is that when I go to settings and check updates the software gives me a network error. I try to disable firewall but it doesn't change. You should find an alternative procedure to update your controller.
If i want to use only one fan do i have to buy the controler hub ?
in order to control the lcd u will need the hub ... that's the only want to customise the lcd to display what u want... it reads via the 9pin usb cable from hub... let me test it for u without the hub..but I'm pretty sure u need the hub...ok I've confirmed u can't control lcd screen unless u have the hub .. if u don't care for lcd display then get non lcd tl fans and u can just connect using the leds
@@MIKEYZVLOGZ Thanks, I wanted to use a fan to put on my CPU cooler. That you could see the temperature and put gift.
My L-connect 3 does not detect my fans or fan controller, even though it has been updated to the newest software.
did u follow the trouble shooting steps?? did u reset the pc after making changes?
have you connected all the cables 6pin pcie, sata , 9pin usb 2,0 directly to mobo
and used ports 2 3 or 4 on hub ?
@@MIKEYZVLOGZ yes I did all of these steps multiple times yet still no luck
@@glizzymob7294 hmm thats very strange , u may need to contact them and ask for more advice, as i only followed their troubleshooting steps and it was a success
hi, did you manage to solve it? I can't update the controller software 0.51 and the fans are not detected.
It doesn’t work please help me!
what's wrong... the display stuck on logo ? or one of them not working ? how many are on and most importantly make sure u update all firmware first and download latest version of software
once u update latest fw and sw make sure u plug in the sata cable and the usb 9pin into the motherboard directly..now also plug in the cable into hub but choose either port 2 3 or 4 on the hub...do not use port 1 on hub ..it won't work