Thank you for all this advice. Very nice video with many very clear explanations. Now I'm going to get to work putting my wrap on my boat. A big thank you from France!
I want you to know, I wrapped the top rail of my 190 tracker and followed your video to the T. Thank you, what a great job of explaining you did, perfect! Will be doing sides soon.
Man bro you did it! Remember we bought our boats around the same time and we talked about your wrap plans. I dig it! Wish you had pics or a walk-around of the whole completed wrap. I kinda see it in your other vids. Question: Are you gonna paint the console to match? If you are ever near WA I'll airbrush it for you. I did Brian Lattimore's (BLatt) - and sneakers and a few crankbaits for him.
You make it look so easy, but I can tell…I am totally going to end up with it wrapping on itself and get pissed off. If the boat is 20” wide, how much bigger do I need the wrap to be?
How is the wrap holding up under the waterline? My black tracker needs paint, but I may try to just gloss wrap it over painting, do you think it will hold up long term?
Try one with rivets and a rib down the side. It took me 2 hours per side on an 85’ 18’Alumacraft. I didn’t use any seam sealer mines been on for 2 years not a pealed place on it. I cut it 1 inch above the bottom of the boat. Putting on a wrap is not for a beginner. I only used the heat gun on the rivets.
There are different wrap materials but 3M IJ180Mc-10 was used on this boat, and can be used on vehicles as well. Side note, the gloss laminate is 3M 8518.
How much should it cost to have someone print out a wrap like yours to install it yourself? I have the exact same boat but white and your wrap looks super legit. I want it 😆
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Thank you for all this advice. Very nice video with many very clear explanations. Now I'm going to get to work putting my wrap on my boat. A big thank you from France!
Finally found the Bob Ross of boat wrapping
That looks sooooo good! Now I want to wrap my boat! Great video 👍
Absolutely!!!
Looks Great. I didn't even think about doing something like this to my tracker. Thanks.
It’s a great paint protector or makes an older tracker look new again 😎
I want you to know, I wrapped the top rail of my 190 tracker and followed your video to the T. Thank you, what a great job of explaining you did, perfect! Will be doing sides soon.
Nice!!
Great job, u have me thinking about doing my tracker now.
It’s a great investment, save my paint a few times already!
Man bro you did it! Remember we bought our boats around the same time and we talked about your wrap plans. I dig it! Wish you had pics or a walk-around of the whole completed wrap. I kinda see it in your other vids.
Question: Are you gonna paint the console to match? If you are ever near WA I'll airbrush it for you. I did Brian Lattimore's (BLatt) - and sneakers and a few crankbaits for him.
Nice work! Thanks for your efforts!
Thanks for watching!
Awesome, brother. looks great.
That's badass bro, would this work on an older aluminum bass tracker?
Thanks for the vid
Absolutely!
Man That looks really good
Thanks! Came out real nice 👍👍
You make it look so easy, but I can tell…I am totally going to end up with it wrapping on itself and get pissed off. If the boat is 20” wide, how much bigger do I need the wrap to be?
Wow that looks awesome!!
Where did you get the wrap
Have you ever used cutting tape to run your edges
Yes, I use it all the time.
Do you do this for a living?
Great Job! Thanks for sharing!
Awesome Job❤
Looks great
Nice video
Any problems going over the original decals? Car you see them after the wrap is on?
You can layer over the decals with no issue. They are slightly embossed under the wrap.
Your pretty good at making these videos you ol blueberry
Hello sir
Do you want to come do my Ranger next it's very similar to the tracker the rt188
Will it bond on sanded 2500grit or need to be polished surface. And is foil good aginst algee?
Sick shop dude, what dolly do you use to move your boat around inside the shop?
I just roll it around, it’s not a double axle.
Thanks
Did u have to cut around the hull numbers ? Great video 👍
Replace with new decals ✌️
What different steps for wrapping fiberglass?
Same, as long as the gel coat is in good condition. No oxidation or roughness, needs to be slick to stick 🤙
Wow its very nice design of vinyl wrap.i really like it.may i know where i can buy that?
Where you popped the pin holes to release the air bubble would you put sealer over them
No sealer needed, just post heat and your good to go!
How is the wrap holding up under the waterline? My black tracker needs paint, but I may try to just gloss wrap it over painting, do you think it will hold up long term?
Still like brand new, I wrap boats professionally.
How much did the printed wrap cost or did you print it yourself?
Depends on the shop, $8-$10 a sqft normally for 3M-IJ180
Question: so you just trim to rub rail.
Yep!
No need to silicone, unless you need too.
How long does a boat wrap last?
They average 3 years, depending on usage and sun exposure.
Hey bud where u get ur wraps from
I design them, and Raptor in Rogers prints them for me.
Were can I get that wrap
What would something like that cost shipped?
Most places are 100$ per linear foot.
Can you put knifless tape to primer and still use the tape to cut?
Yes it works well on top of primer 94
Is it difficult to remove the plastic casing around the cut tape once it’s put over the primer.
How do you apply sealer to the edge if you cut the wrap flat without overlapping to the bottom?
Just wipe it on, vinyl to hull
I bought a brand new tracker today. can I bring mine to you let you wrap it??
For sure, check out Raptor Wrap and Sign in Rogers. 🤙🤙
Try one with rivets and a rib down the side. It took me 2 hours per side on an 85’ 18’Alumacraft. I didn’t use any seam sealer mines been on for 2 years not a pealed place on it. I cut it 1 inch above the bottom of the boat. Putting on a wrap is not for a beginner. I only used the heat gun on the rivets.
Rivets are definitely fun, good times!
Awsome vid 👌🏻! I have 2016 Pro170 that I would like to wrap, Do you sell the wraps and ship them for a do it yourself kind of proyect?
I don’t, sorry.
Did you not want to take the Tracker graphic off?
Kept it on for resale value.
I’m looking for a wrap for my bass tracker any recommendation
Raptor Wrap And Sign in Rogers. 👍
Where did you get the wrap?
Raptor Wrap and Sign in Rogers, AR.
Hi it's same vynil as car wrap?
Yes, it is.
@@BentRodBassin thanks
is there a difference between car wrap and boat wrap
material?
There are different wrap materials but 3M IJ180Mc-10 was used on this boat, and can be used on vehicles as well. Side note, the gloss laminate is 3M 8518.
greetings friend, how can I buy that for my BASS TRACKERS
Come on by an well get you taken care of 🤙
How much should it cost to have someone print out a wrap like yours to install it yourself? I have the exact same boat but white and your wrap looks super legit. I want it 😆
Depending on design cost, I’d estimate around $700 👍
@@BentRodBassin thanks man super cool!
@@BentRodBassin what state are you in
I have a boat that is a black hull with stickers. How does your wrap work wrapping on top of your existing logos?
What would something like this cost?
Depends on the shop, material and design time.
NICE!
Ready to rip some lips!
3m Knifeless Tape......