Just got a browning safe. The sheet with the code said read instructions for changing combinations and the instructions said to read the combination pamphlet to change it. Lol. This worked perfectly. Thanks so much!!!!!
Thank you for the informative video, it made changing the battery a breeze. I have a summit safe and it wont allow me to extend the bolts with the door open as you are able to do in the video.
LOL!! 41 thumbs down? LMAO! What's not to like? He shows how to open it, change your combo and replace the battery. Just like it says in the title! Maybe expecting a cheeseburger surprise?
I had the same problem with my safe. You have to rotate the chrome cover till it comes off then on the left side of the battery push to the right until it clears the 2 screws that hold cover in place. Now simply push up on the black plastic and the cover will come off. BTW, It's not at all like the video. The battery does not have a pocket to sit in. It slides in and out. Hope that helped. Worked fine after I found the solution. Good Luck.
It's just like Ron Typin posted. Mine would come up a little but not pop off. Rotate the chrome cover counter clockwise slightly,pull off. Then your battery will slide out to the right.I pushed it out with a screwdriver.The battery is putting too much pressure on the double keyhole slots which is why it's not popping off like it is suppose. Thanks again Ron! Great informative video Dean Safe!
Many safes have a Button detent that keeps the bolt from going back out while the door is open it’s a safety device that prevents the door from being slapped on the bolts and bending them. If you carefully run your fingers along the back edge of the door. Once in a while it’s on the top or bottom of the door. When you find it you push it in and you will be able to retract the bolts. I hope this information is helpful to you. Thanks, John
After my battery died, I watched your video and followed your instructions on changing out the battery on my electric keypad Cannon safe. It did not recognize my combo code. I entered it several times and it didn't work. I tried to enter the factory code of 123456 and that didn't work. I did this several times. Am I locked out forever?
Just so you know you’re not the only person in the world that’s thrown the instructions inside the safe and then locked it. Actually I have a feeling it’s quite common.
How come in this video it shows the user slightly lifting up on the lock to change the battery while I attempt to do the same and I end up practically almost lifting up the front of a 350lb safe and mine still wont come off. And yes its a SecuRam lock
What happens if you put the wrong code in and it keeps beeping?? Will it reset itself?? I tried to change the combo but screwed it up. Now it’s continuously beeping.
Maximum deep in time is 15 minutes after it resets code put in the right code it opens. Put in the wrong code it beeps again.. Thanks for watching, John
I have had my cannon safe with securam locking system for exactly 1 year. I went to get into to it yesterday and it wouldn't recognize the code. 3 beeps, after 4 attempts it went into lock out mode. After several repeated attempts I gave the opener handle a firm tug and...the stopper bar slipped past the magnetic lock release. I was shocked. This safe is NOT SECURE. I removed the inner backing that hides the locking mechanism and saw how poorly it is made. Not a good safe at all.
My combination is no longer working and appears to have a defect or short in the electronic components. It did not recognize the numbers 1,2,3,5, and 8 whenever I input the combination it would beep 3 times, and then after 2 or 3 attempts (not five,) put me into lockout mode. Any tips?
Sounds lock the keypad is malfunctioning, time to call a safe tec or a safe savvy locksmith. you can always try to wait 15 min and give it another shot. If you do get it open get a safe guy our before you close it. Good luck, John
Tied to get the lock pad off and it isn't as easy as in the video. I hear the click but there's no getting it's face off to get to the battery. There feels like something is still holding it in place. Does anyone have any suggestions
You probably have the " top lit " version. Try turning the trim ring counter clockwise 1/4 turn. Then puss the battery out with your finger from right to left. The whole unit will then lift up & off .
SecuRam has a ton of quality locks to pick from and I would expect and some have different ways to install the battery. All is not lost. SecuRam has a great website, just find a keypad that looks like yours and you should be good to go. If all else fails call them I’ve found them very helpful. Thanks for watching, John
+james bandy If you have a SecureRam lock on your safe and it's not this one, go to the SecureRam website they have excellent instructions on their other products. Thanks for watching, John
+james bandy I am having the same problem. it is the same faceplate as this one but I cannot get to the dam battery. how did you finally get to your battery??? thanks
+Popcorn they should be able to help you with that, however you’ll probably need to jump through a hoop or two. Give them a call at, 800-701-9128 hope this helps. Thanks for watching, John
+Ballista leave the battery in for 20 minutes and see if it stops. It could be in the lockout mode. The lockout timer goes on hold until the battery is reinstalled. Try this first. John
That would be annoying, 20 minutes of beeping? I think this combo lock us not worth it if it makes you wait 20 minutes and beeps at you the whole time.
You probably have the " top lit " version. Try turning the trim ring counter clockwise 1/4 turn. Then push the battery out with your finger from right to left. The whole unit will then lift up & off
Troy Carr Troy, I finally did get the lock off, but very frustrated. The screw that holds the lock in place was tilted inward at the top holding it very tight to the safe. Thanks.
Worry not, most safe manufactures maintain override codes for Elocks and combos for dials. They are very difficulty to get but it's cheaper than drilling. If you can not get an over ride code you'll need to get a safe teck to get into it for you. thanks for watching, John
DeanSafe i have a rhino iron works safe. i have forgotten the combination. is there a way to get an over ride code for a rhino iron works safe? been trying to open it for a while now.
That's the original factory code and should have been changed to a different code on the first use. So you may not have the right code. If your sure that it's never been changed, then change the batteries (Alkaline only) and change the code. Still no luck, call a safe service man. Thanks for watching, John
+Buddy Sawyer If a burglar cuts the wires to the keypad has just locked out everyone until #1 The keypad is reattached. #2 the safe is drilled open and the lock and keypad is replaced. This is very similar to what we do when a burglar pops the dial off of a mechanical lock. Thanks for watching, John
Dean Safe to the rescue again! I worked for John Dean's locksmith shop almost 30 years ago...great guy and great company!
Very cool! Thank You, John (Yep Still alive and kicking)
Just got a browning safe. The sheet with the code said read instructions for changing combinations and the instructions said to read the combination pamphlet to change it. Lol. This worked perfectly. Thanks so much!!!!!
Good to hear, John
Very happy we were able to help.
Thanks much, John
Thank you for the informative video, it made changing the battery a breeze. I have a summit safe and it wont allow me to extend the bolts with the door open as you are able to do in the video.
LOL!! 41 thumbs down? LMAO! What's not to like? He shows how to open it, change your combo and replace the battery. Just like it says in the title! Maybe expecting a cheeseburger surprise?
I don’t quite understand it myself. Could be competitors or more likely they think I’m giving Safe cracking lessons. 🤷🏼♂️
MY FRIEND WILL BE HAPPY THANKS
Thank you too, John
thank you for information you saved me a lot of money by not getting a locksmith out to my place just
Happy to do so. Thanks for watching, John
Great video. Thank you.
Our pleasure! John 😊
Thank you, this was very helpful
Thanks this was easy to fallow. Just got my new Cannon 24gun safe.
Thanks You for posting this very helpful video
+2002honda954 So glad I could help, thanks for watching
Perfect and straight to the point
Thank you John
I had the same problem with my safe. You have to rotate the chrome cover till it comes off then on the left side of the battery push to the right until it clears the 2 screws that hold cover in place. Now simply push up on the black plastic and the cover will come off. BTW, It's not at all like the video. The battery does not have a pocket to sit in. It slides in and out. Hope that helped. Worked fine after I found the solution. Good Luck.
My battery on my Bighorn classic was so dead it would not even send the open signal thanks for the info saved me a lot of hassle.
It's just like Ron Typin posted. Mine would come up a little but not pop off. Rotate the chrome cover counter clockwise slightly,pull off. Then your battery will slide out to the right.I pushed it out with a screwdriver.The battery is putting too much pressure on the double keyhole slots which is why it's not popping off like it is suppose. Thanks again Ron! Great informative video Dean Safe!
Many safes have a Button detent that keeps the bolt from going back out while the door is open it’s a safety device that prevents the door from being slapped on the bolts and bending them. If you carefully run your fingers along the back edge of the door. Once in a while it’s on the top or bottom of the door. When you find it you push it in and you will be able to retract the bolts. I hope this information is helpful to you. Thanks, John
Thanks. It worked
What the Cannon owners manual does not tell you is you have to enter new numbers "quickly" or it will not accept new code. This is on a NL lock.
Ok, but i just bought my safe and lost the instructions, so do is still use 123456 for the first time to set my combo?
After my battery died, I watched your video and followed your instructions on changing out the battery on my electric keypad Cannon safe. It did not recognize my combo code. I entered it several times and it didn't work. I tried to enter the factory code of 123456 and that didn't work. I did this several times. Am I locked out forever?
Thanks for the Great Video!!!
If you lose your combination can cannon help you reset it, or does the whole lock have to be replaced?
Thanks,
been trying to figure it out myself, i lost my paper with the password on it and i can’t find any information on ways to help such as an override code
Awesome video!
Thanks bud
Happy to help, John
Thank u for this
So glad we were able to help, thank you for watching,
John
forgot my combo on my bighorn sate..electronic lock as shown in the video
Does anyone make a good safe that has both electronic and dial locks? I like the speed of an electronic lock and the reliability of a dial lock.
Thank you, my battery died and my instructions were inside
So happy we were able to help. Thanks, John
Just so you know you’re not the only person in the world that’s thrown the instructions inside the safe and then locked it. Actually I have a feeling it’s quite common.
How come in this video it shows the user slightly lifting up on the lock to change the battery while I attempt to do the same and I end up practically almost lifting up the front of a 350lb safe and mine still wont come off. And yes its a SecuRam lock
What happens if you put the wrong code in and it keeps beeping?? Will it reset itself?? I tried to change the combo but screwed it up. Now it’s continuously beeping.
Maximum deep in time is 15 minutes after it resets code put in the right code it opens. Put in the wrong code it beeps again.. Thanks for watching, John
I have had my cannon safe with securam locking system for exactly 1 year. I went to get into to it yesterday and it wouldn't recognize the code. 3 beeps, after 4 attempts it went into lock out mode. After several repeated attempts I gave the opener handle a firm tug and...the stopper bar slipped past the magnetic lock release. I was shocked. This safe is NOT SECURE. I removed the inner backing that hides the locking mechanism and saw how poorly it is made. Not a good safe at all.
Gotta go with a TL-15 or higher if you need serious security
My combination is no longer working and appears to have a defect or short in the electronic components. It did not recognize the numbers 1,2,3,5, and 8 whenever I input the combination it would beep 3 times, and then after 2 or 3 attempts (not five,) put me into lockout mode. Any tips?
Sounds lock the keypad is malfunctioning, time to call a safe tec or a safe savvy locksmith.
you can always try to wait 15 min and give it another shot. If you do get it open get a safe guy our before you close it. Good luck, John
does this same procedure work for a UL type lock on TS series?
Only if it is using the Securam lock. Most Amsec ts safes use an ESL 5 for ESL10 Lock look for our video on that one.
Thanks,
John
Tied to get the lock pad off and it isn't as easy as in the video. I hear the click but there's no getting it's face off to get to the battery. There feels like something is still holding it in place. Does anyone have any suggestions
You probably have the " top lit " version. Try turning the trim ring counter clockwise 1/4 turn. Then puss the battery out with your finger from right to left. The whole unit will then lift up & off .
Are all securam locks the same ? I mean , when it comes to change battery 🔋? Please , someone reply to me 🙏
SecuRam has a ton of quality locks to pick from and I would expect and some have different ways to install the battery. All is not lost. SecuRam has a great website, just find a keypad that looks like yours and you should be good to go. If all else fails call them I’ve found them very helpful.
Thanks for watching, John
@@DeanSafe thank you for quick response ☺️🙏
I open the safe door and put pegs out. enter 0 six times and the locks signals that I put the wrong combination in. Please help.
Go to www.securamsys.com/ great videos and instructions.
good luck,
John
The battery is not exposed when I pull the lock off. How do I get the plate off to replace the battery??
+james bandy If you have a SecureRam lock on your safe and it's not this one, go to the SecureRam website they have excellent instructions on their other products.
Thanks for watching,
John
+james bandy I am having the same problem. it is the same faceplate as this one but I cannot get to the dam battery. how did you finally get to your battery??? thanks
Do you have to use 6 digits
Gary F ya
LOL
my key pad beep after I change the battery
i have a rhino ironworks safe, i forgot the password. i’m freaking out. is there a way to get an overide code from rhino ironworks
+Popcorn they should be able to help you with that, however you’ll probably need to jump through a hoop or two. Give them a call at, 800-701-9128 hope this helps.
Thanks for watching,
John
mine keeps beeping when i plug into the battery what do i do
+Ballista leave the battery in for 20 minutes and see if it stops.
It could be in the lockout mode.
The lockout timer goes on hold until the battery is reinstalled. Try this first.
John
That would be annoying, 20 minutes of beeping? I think this combo lock us not worth it if it makes you wait 20 minutes and beeps at you the whole time.
This sucks. Have attempted all afternoon and can't get it off. I wondered about the lock when I bought it. Would much prefer a keyed lock.
You probably have the " top lit " version. Try turning the trim ring counter clockwise 1/4 turn. Then push the battery out with your finger from right to left. The whole unit will then lift up & off
Troy Carr
Troy, I finally did get the lock off, but very frustrated. The screw that holds the lock in place was tilted inward at the top holding it very tight to the safe. Thanks.
What if I've forgotten my combo
Worry not, most safe manufactures maintain override codes for Elocks and combos for dials. They are very difficulty to get but it's cheaper than drilling. If you can not get an over ride code you'll need to get a safe teck to get into it for you.
thanks for watching, John
DeanSafe i have a rhino iron works safe. i have forgotten the combination. is there a way to get an over ride code for a rhino iron works safe? been trying to open it for a while now.
That’s the same code as my luggage
not able to open door with 1,2,3,4,5,6 then what
That’s the original factory code which was most likely changed by the first person to use the safe. Changing the combo erases the previous code.
That's the original factory code and should have been changed to a different code on the first use. So you may not have the right code. If your sure that it's never been changed, then change the batteries (Alkaline only) and change the code. Still no luck, call a safe service man.
Thanks for watching,
John
So what happens when a burglar comes in and cuts keypad wires????
+Buddy Sawyer If a burglar cuts the wires to the keypad has just locked out everyone until #1 The keypad is reattached. #2 the safe is drilled open and the lock and keypad is replaced. This is very similar to what we do when a burglar pops the dial off of a mechanical lock.
Thanks for watching, John