I’m shocked you didn’t think instantly that m92t36 chip would be part of the problem. It seems to be the problem in most faulty switches. I repaired one for my channel recently and it was one of the biggest repairs I’ve done, but i felt confident because of watching channels like yours constantly! Keep it up, very entertaining.
As the diode is right by a big inductor, my guess is that it is a schottky and is used as part of a buck regulator, so probably not too critical apart from needing to be able to handle the current.
Is it a "flyback/flywheel" diode? According to what i researched you can put a diode across a inductor and apparently its serves to reduce the ripple kinda the same purpose of the decoupling capacitors at the output of a buck converter. i'm a noob to board repair and electronics so i could be way wrong.
... and a diode in that circuit will show shorted even when it may not be. Both diode leads have to be tested off the circuit because of the inductor, little to no resistance in inductors.
Thank you that you also have more difficult repairs to diagnose many before the video and only show what is broken and exchange it. But the way is the goal!
im at 5:30 , im also a repair tech but not much advenced as you for month ive suffered of a general ''piss off'' about how much people tryed to screw me up ive not repaired any flatscreen since close to 7 month now , you share some of gold hints that ive never considerated , at the point of listening your videos give me the impression that its slowy reactivate my passion for electronic repairing ,, i dont know how to thanks you for that , but thank you from quebec canada
Machallah you are Profi, we learn from you so much , ich have a repair Shop in Germany but what you do is perfekt and how you teach and explain all what you do and whats happening.. Thank you very much , love you from Germany
Watching you do these repairs is interesting but my soldering skills are not very good. This is why I leave all my device repairs to the pros. I will solder speaker wires and such but that is it. Great Job.
Boss, do not apply pressure on the chip with the bottom pedestal chips. If you have applied Flux to the leg paths, it will be sufficient to put the chip in its socket and heat it at low speed and sufficient temperature. The chip will sit by itself. Touching each other is very common as there will be contact in the invisible place even if you apply pressure on the chip and apply flux. Because you are already renewing and inflating the solders. If you renew the solder with minimal cleaning then you can apply light pressure. This is my experience and opinion. Kind regards,
I have the same problem with my quadcopter's flight controller. The Schottky diode was shorted I removed it & no short on the FC. I'm not able to find that diode anywhere on the internet. I would love to see how you find the right components without donor boards.
I think many diode would work, Just figure out the forward voltage to see if it's a normal diode ( about 0.6V) or a schottky diode ( forward voltage 0.145 to 0.45 V), it should not make much difference. Unless it's a zener,the you need to figure out the reverse voltage, but the symbol on the board is not the Zener symbol.
I guess you can measure similar diode from the same switch lite. But I wonder how much is this repair. It took a lot of time but the switch lite is not that expensive.
I have same issue with Switch Lite. Some say that it could be GLZ6.8C others SMZ2568. Did someone try and successfully installed this part? Where to buy replacement? @NorthridgeFix any chance for update?
Being in repair for a short time myself, I simply do not believe anyone that says they didn't try to fix it at all. If it turns out to be true, great. More often than not it will have been tampered with. Now, that's ok! Fine. Just tell me. It makes the repair harder to pretend it's in factory condition as you hand it to me. Finally, I always wonder why we lie about the things we lie about. Ya know? Lmao Like, just tell me you tried fixing it. I respect people that want to fix things! Just tell me but even when it's blatant they'll look me in the eye and say they didn't (or anyone else). It's amazing.
I use a small kim wipe on the board, then I scrub with iso soaked qtip on top of that. Strings of cotton doesn't snag on the components, its not abrasive on delicate pads, and the wipe absorbs the dissolved flux very well. Without just pushing the flux it around and having it flow all over the board. Then move to a clean section of the wipe if there is a lot of flux to absorb.
May I know what machine you're using to test in this video,I just saw a black tools long stick with sound to to to when you're checking the short circuit ?
@@omaribrahim2736 its confusing because a circuit should generally be a loop and we dont get to see where hes placing the second probe, since only one shows up on camera.
when you mentioned that the chips from this device does not short that easily, does it mean that we can use a phone cooler with an active cooling part inside for cooling? The one's with a peltier module or TEC chip inside?
I had my Lite charged to 100%, while plugged in I played for a few hours and the battery life was at 23% when I was done. I dont understand why it drained while plugged in. ??????
checked it not enough info to id the 8c diode correctly but id say if it were up to 15v 1a ish should be ok or a diode that has the same measurements as the old one probable a shottkey one
Hello good look I have a problem with a lite and I have tried everything with it and nothing But it surprises me that when I remove the charging cable, the home button turns on and off suddenly, I think it is the battery that does not receive a charge, any suggestions, thanks
I'm having the same problem my switch won't charge or turn on or anything it could be a dead battery or it could be the issue that you're explaining on here where do I send it to you guys so I can have it fixed
Great job. I have the same problem but i have light in the charger, when i turn on the lap just flash and turn off, i don't have a termical cam, how the find the short?
I'm trying to fix a Switch Lite with blank screen no sound, it turns on partially as I can see the back light come on and I have felt the APU warm up. Where do you think the issue would be? any help would be greatly appreciated.
hye sir.. can u share with me what kind of thermal camera ur using.. thats look smooth compared to the one we use for phone board repair which is QianLi brand..
Go to the power IC’s data sheet and look at some of the reference designs to see what shottky diode they are using. Then match the specs of that diode to to a shottky diode that matches your pcb footprint.
Hello, thank you very much for your video. What is the setting power for desoldering an "IC" component. How much do you regulate the air flow and temperature? I cannot remove the M92T36 component. Sorry for my English. It's a translation, I'm French.
Now I don't want to be an eyesore for other techs if a customer needs a different repair in the future, or I have a case I deem too complex for my current stage of skill (still learning) - but I never wick off solder if I get a little bit on a test pad. Unless its a big raised blob of course. I mean, it was already an open, bare metal pad. Surface used to be dull copper, now it's shiny tin and lead. I am a little curious how other techs deal with flux that's in between components, not in/on ports or chips with thermal paste. I usually clean it very thorough, although that is not risk free either, especially with iphone boards. Tube says _no-clean_ flux - does anyone leave it on?
my nintendo switch lite short no power after install cfw mod sx lite but now is okand working ,but now my micro sd slot cant read my sd card and cant go to sx os boot
I do mobile phone repairs but its basic just changing screen and batteries and I would like to explain my knowledge and become an expert such as you in repairing. How can I become an expert like you? What things do I need to learn? Are there any training school that you recommend or subjects?
Thanks Brother. I had a switch lite board with the same issue. replaced both chips still had a short. Replaced that diode and what do you know? Success! You guys are awesomee
@@ConsoleFixLV Hello, I looked on the Mouser website but what is the exact value of the component please? There is still a small package. I'm in the same boat with the same breakdown and I don't have a donor board. Thank you :)
Got a Nintendo switch with no TV display/signal when docked. Also it's bent for some reason along the center vertical line. It charges and plays fine in handheld mode. I don't have a spare dock to try. I tried a different cable, HDMI port, monitor, still no TV display. Any suggestions?
Check the connector first Then do some measurement with voltage in .both V source and the 3.3 If its good. Go check the enable signal and the pwm.. There is some test point around it.. Might this works
hi friend how are you? im trying to repair some nintendo switch im from mexico, i got a short from one of the charging chip capacitors and check the capacitors from the gpu and only one got short its that normal?
what temp do generally have your air set to? This must be hard as to what to charge, I would have to guess you don’t give an exact amount just T&P(time and parts) job. Very good videos and very well explained. .
Almost 300 temperture and 3 air speed. Or you can find another video on this same Chanel. This channel can help you in different techniques for fixing the problems.
لماذا جربت الجهاز قبل ان تتأكد من زوال الشورت ؟ يعني لماذا جعلت البيج بوص يجمع الجهاز؟! , لا ادري هل مرت عليك حاله من قبل فيها شورت و اشتغل معك الجهاز ؟
I wouldn't get anything below 30fps. Look up reviews on amazon and make a decision. The one i have is the only one i've used and i can't suggest any specific one.
MashAllah, I hope you can give me the opportumity to be your student .I have level minus 0 :) :) but i learn fast and love this work .I can travel all over europe in summer only
![BLACK BAG - Official Trailer [HD] - Only in Theaters March 14](http://i.ytimg.com/vi/Du0Xp8WX_7I/mqdefault.jpg)
It's great that more and more guys are out there actually fixing electronics rather force everyone to throw away and buy new.
I like when you share the process and the difficult of the work.
I’m shocked you didn’t think instantly that m92t36 chip would be part of the problem. It seems to be the problem in most faulty switches. I repaired one for my channel recently and it was one of the biggest repairs I’ve done, but i felt confident because of watching channels like yours constantly! Keep it up, very entertaining.
When i see your videos you make me reconsider my career's choices ! I love what you do
True ❤️
Love clear motherboard close-ups, and quick diagnosis/repairs.
As the diode is right by a big inductor, my guess is that it is a schottky and is used as part of a buck regulator, so probably not too critical apart from needing to be able to handle the current.
Is it a "flyback/flywheel" diode? According to what i researched you can put a diode across a inductor and apparently its serves to reduce the ripple kinda the same purpose of the decoupling capacitors at the output of a buck converter. i'm a noob to board repair and electronics so i could be way wrong.
The buck stops here.
Like to work with u
... and a diode in that circuit will show shorted even when it may not be. Both diode leads have to be tested off the circuit because of the inductor, little to no resistance in inductors.
This video needs a part 2! What's the value of that diode after all?
Thank you that you also have more difficult repairs to diagnose many before the video and only show what is broken and exchange it. But the way is the goal!
I record whatever i'm working on. I do not pick and choose easy or hard repairs.
im at 5:30 ,
im also a repair tech but not much advenced as you
for month ive suffered of a general ''piss off'' about how much people tryed to screw me up
ive not repaired any flatscreen since close to 7 month now ,
you share some of gold hints that ive never considerated , at the point of listening your videos give me the impression that its slowy reactivate my passion for electronic repairing ,,
i dont know how to thanks you for that , but thank you from quebec canada
Machallah you are Profi, we learn from you so much , ich have a repair Shop in Germany but what you do is perfekt and how you teach and explain all what you do and whats happening..
Thank you very much , love you from Germany
😂😂😂😂 you Speck beste englisch
@@hanswurst117 your name says it all
@@hanswurst117
Was willst du , sag mir !
Jalal Othman 5 Millionen €
Watching you do these repairs is interesting but my soldering skills are not very good. This is why I leave all my device repairs to the pros. I will solder speaker wires and such but that is it. Great Job.
Boss, do not apply pressure on the chip with the bottom pedestal chips. If you have applied Flux to the leg paths, it will be sufficient to put the chip in its socket and heat it at low speed and sufficient temperature. The chip will sit by itself. Touching each other is very common as there will be contact in the invisible place even if you apply pressure on the chip and apply flux. Because you are already renewing and inflating the solders. If you renew the solder with minimal cleaning then you can apply light pressure. This is my experience and opinion. Kind regards,
As allways, Awesome job!
Thanks Brother
Great diagnosis. We need an update! 🤣
It's a pleasure to watch and listen your videos!
Diodes in looped/feedback circuits will appear shorted. Must test "both" diode leads separate from the circuit.
I have the same problem with my quadcopter's flight controller. The Schottky diode was shorted I removed it & no short on the FC. I'm not able to find that diode anywhere on the internet. I would love to see how you find the right components without donor boards.
I think many diode would work, Just figure out the forward voltage to see if it's a normal diode ( about 0.6V) or a schottky diode ( forward voltage 0.145 to 0.45 V), it should not make much difference.
Unless it's a zener,the you need to figure out the reverse voltage, but the symbol on the board is not the Zener symbol.
Unless it's a Zener, then you need to figure out the reverse voltage using the multimeter.
Great video quality and visibility
No word to say !👌🏽
I guess you can measure similar diode from the same switch lite. But I wonder how much is this repair. It took a lot of time but the switch lite is not that expensive.
thanks for sharing your soldering skills and knowledge priceless
I have same issue with Switch Lite. Some say that it could be GLZ6.8C others SMZ2568. Did someone try and successfully installed this part? Where to buy replacement?
@NorthridgeFix any chance for update?
Any update on yours?
Did you fix it?
Still wondering if you found a diode to replace it and what the values are.
Wonderful detective skill, thank you
Hi #Boss, hope u r fine, happy to see you after a week time.......... 🙏🙏🙏
Anyone know what the diode is? Replaced the bq chip as was short but the diode was bad, blown. Any idea what the value is?
please explain how to understand short or not with resistance mode?
Being in repair for a short time myself, I simply do not believe anyone that says they didn't try to fix it at all. If it turns out to be true, great. More often than not it will have been tampered with.
Now, that's ok! Fine. Just tell me. It makes the repair harder to pretend it's in factory condition as you hand it to me.
Finally, I always wonder why we lie about the things we lie about. Ya know? Lmao
Like, just tell me you tried fixing it. I respect people that want to fix things! Just tell me but even when it's blatant they'll look me in the eye and say they didn't (or anyone else). It's amazing.
Do you have any videos that show you replacing the retaining clamp on a ribbon clip.
I use a small kim wipe on the board, then I scrub with iso soaked qtip on top of that. Strings of cotton doesn't snag on the components, its not abrasive on delicate pads, and the wipe absorbs the dissolved flux very well. Without just pushing the flux it around and having it flow all over the board. Then move to a clean section of the wipe if there is a lot of flux to absorb.
May I know what machine you're using to test in this video,I just saw a black tools long stick with sound to to to when you're checking the short circuit ?
Do you mean the multimeter?
@@omaribrahim2736 its confusing because a circuit should generally be a loop and we dont get to see where hes placing the second probe, since only one shows up on camera.
Why @3:45 did you not use flux to remove the chip?
What's that gel u use boss?
when you mentioned that the chips from this device does not short that easily, does it mean that we can use a phone cooler with an active cooling part inside for cooling? The one's with a peltier module or TEC chip inside?
I had my Lite charged to 100%, while plugged in I played for a few hours and the battery life was at 23% when I was done. I dont understand why it drained while plugged in. ??????
why yould you assume the usb port was soldered properly when it looked like that?
Do you fix v2 boot logo only..
Nintendo logo display only
beautiful work! we can learn a lot from you, thanks for sharing
checked it not enough info to id the 8c diode correctly but id say if it were up to 15v 1a ish should be ok or a diode that has the same measurements as the old one probable a shottkey one
very nice video, real job in real time ! At what temperature do you solder chips ? thanks
Hello good look I have a problem with a lite and I have tried everything with it and nothing But it surprises me that when I remove the charging cable, the home button turns on and off suddenly, I think it is the battery that does not receive a charge, any suggestions, thanks
Bonjour quelle camera thermique utilisé vous
We love ur job sir..love from India.
Not just enjoy the video but learned a ton of knowledge
I'm having the same problem my switch won't charge or turn on or anything it could be a dead battery or it could be the issue that you're explaining on here where do I send it to you guys so I can have it fixed
Hello, is there such capacitor that is universal or are they all different?
can we use a 1ampere shut key diode 🤔?
Great job. I have the same problem but i have light in the charger, when i turn on the lap just flash and turn off, i don't have a termical cam, how the find the short?
Did u fix
As usual I enjoyed your video.
Keep up the good work.
whats the temperature you use plz your soldering iron
I'm trying to fix a Switch Lite with blank screen no sound, it turns on partially as I can see the back light come on and I have felt the APU warm up. Where do you think the issue would be? any help would be greatly appreciated.
hye sir.. can u share with me what kind of thermal camera ur using.. thats look smooth compared to the one we use for phone board repair which is QianLi brand..
I hear your kids in the background haha love it!!!
Go to the power IC’s data sheet and look at some of the reference designs to see what shottky diode they are using. Then match the specs of that diode to to a shottky diode that matches your pcb footprint.
Hello, thank you very much for your video. What is the setting power for desoldering an "IC" component. How much do you regulate the air flow and temperature? I cannot remove the M92T36 component. Sorry for my English. It's a translation, I'm French.
avec une temperature de 400-420 et 50% d'air
Now I don't want to be an eyesore for other techs if a customer needs a different repair in the future, or I have a case I deem too complex for my current stage of skill (still learning) - but I never wick off solder if I get a little bit on a test pad. Unless its a big raised blob of course. I mean, it was already an open, bare metal pad. Surface used to be dull copper, now it's shiny tin and lead.
I am a little curious how other techs deal with flux that's in between components, not in/on ports or chips with thermal paste. I usually clean it very thorough, although that is not risk free either, especially with iphone boards. Tube says _no-clean_ flux - does anyone leave it on?
Big Fan of your work! Can you post links for your Microscope and Camera and camera setup?
What the names of fluid that u always used on the board each times u want solder@desolder the chip etc..?
Flux
my nintendo switch lite short no power after install cfw mod sx lite but now is okand working ,but now my micro sd slot cant read my sd card and cant go to sx os boot
Did you ever find out the value of that diode
red dots on sticker means water damage has occured. timestsamp 2:11
when the water damage occur the dots make the entire sticker red
no water damage happened to this mother board
What brand of meter and model do you have? Looks like a Fluke but model will help a lot, Thanks Alex!
Looks like a Fluke 87
I do mobile phone repairs but its basic just changing screen and batteries and I would like to explain my knowledge and become an expert such as you in repairing. How can I become an expert like you? What things do I need to learn? Are there any training school that you recommend or subjects?
That diode its for protection, you could test without it, and put any diode later
I have the same problem u know how to fix? I replaced diode with a good one but didn't helped
Very smart way to diagnose the problem thanks I have doner bord for intendo switch lite let me know if you still need the pats
Thanks Brother. I had a switch lite board with the same issue. replaced both chips still had a short. Replaced that diode and what do you know? Success! You guys are awesomee
Excuse me, can you tell us where did you purchase that diode that resolved your problem?
@@Rodox2k10 Mouser
I've been looking everywhere for these would you happen to remember what kind of diode it was
@@ConsoleFixLV Hello, I looked on the Mouser website but what is the exact value of the component please? There is still a small package. I'm in the same boat with the same breakdown and I don't have a donor board.
Thank you :)
Very great,,,it helps me alot
Not skipping ads,,i hope it will help you sir
Hi, some diagrama schematic of nintendo swicth lite? i can buy it, thanks for share yours knowledge
What are you using to cut the wire
0:57 That smile haha "oh I don't think so”
20:40 NoDiode huh.
why not use thermal camera?
can you get replacements for MCUs with custom firmware?
hey question for you what type of flux do you use?
northridgefix.com/product/amtech-nc-559-v2-tf-flux-10g-syringe-plunger-2-needle-sizes/
8c is 68 volt zener diode.
plz provide me mobile repairing channel link
like this channel
i want to learn foreign trics
Got a Nintendo switch with no TV display/signal when docked. Also it's bent for some reason along the center vertical line. It charges and plays fine in handheld mode. I don't have a spare dock to try. I tried a different cable, HDMI port, monitor, still no TV display. Any suggestions?
Check the connector first
Then do some measurement with voltage in .both V source and the 3.3
If its good. Go check the enable signal and the pwm..
There is some test point around it..
Might this works
Usb, filtro emi o p13usb
Does the lite and the original switch use the same usb c port?
Haaaaalp I have the exact same issue. But is there a substitute if I don’t have any diodes to replace it with?
Did you fix it?
Did u fix
Anyone knows what stencil can I use to reball a Max77620 ic from a regular Nintendo switch?
hi friend how are you? im trying to repair some nintendo switch im from mexico, i got a short from one of the charging chip capacitors and check the capacitors from the gpu and only one got short its that normal?
I need a flir cam, wish they weren’t so expensive
I just got a seek compact xr on Ebay for 170 dlls
what temp do generally have your air set to? This must be hard as to what to charge, I would have to guess you don’t give an exact amount just T&P(time and parts) job. Very good videos and very well explained. .
450.
@@andreass.7152 Fahrenheit or Celsius?
Celsius
@@andreass.7152 Thanks for the reply. I will have to check my temp setting again...;)
hello i have also the same hot air station... for chip like these, what temperature and fan speed do you use?
Almost 300 temperture and 3 air speed. Or you can find another video on this same Chanel. This channel can help you in different techniques for fixing the problems.
@@jryngki5094 there are not "3" in that station... its from 0 to 120
@@simonspeaker oh you have another Air station, unlike mine...
detective work done, its good as fixed
at what temp do you manage to desolder the chip?
450
Amigo, qual câmera térmica você usa??
Flir E60
9:20 🤗
ولا شي
i think it must be so easy for you to get any kind of board diagram in your country!!!
If a person wanted to make this their career choice, what type of classes do you take?
Thank you for making this vid, i have one that is also shorting at the cap where the BQ chip is, i’ll remove the diode and see if its that it.
Did it work?
Can a diode cause a short? If it is bad is not an open line?
In my experience zener diodes get short, and they are used for protection by over voltage. Generally ground on one end.
Asalaam alaykum, what temperature is your hot air set to?
UP
لماذا جربت الجهاز قبل ان تتأكد من زوال الشورت ؟ يعني لماذا جعلت البيج بوص يجمع الجهاز؟! , لا ادري هل مرت عليك حاله من قبل فيها شورت و اشتغل معك الجهاز ؟
ما ركب الجهاز كله ، بس البطاريه
This is a SURFACE MOUNT SILICON
ZENER DIODES SMZ25 Series
Donde se puede consegir
sir,help me please...super glue has got sticked upon amoled display with frame how can i seperate it safely
You can use a few drops olive oil on . Wait for 5minutes up, and rub it gently
Might this works..
I repair a nintendo switche before with a bad diode... I remove and switch works fine ... In the others models of the boards this diode no exist...
Please suggest a low cost thermal camera sir iam from indian startup
I wouldn't get anything below 30fps. Look up reviews on amazon and make a decision. The one i have is the only one i've used and i can't suggest any specific one.
@@NorthridgeFix thank you sir for your valuable reply here in India prices in Amazon are 10 times higher so please suggest a website sir
MashAllah, I hope you can give me the opportumity to be your student .I have level minus 0 :) :) but i learn fast and love this work .I can travel all over europe in summer only
Where are you from which country
Lebanon born in New York
Awsome work BIG BOSS :)
Very excellent sir. I learn more. Thanks sir. I am in india