2010 750li. One side is about 3” higher and the other side looks normal. I drained both air shocks to lower completely and when I cut on the car, it went to normal height. After 15 minutes I opened the door, the compressor came on and raised the right side the additional 3” for some reason and that is where it’s staying. Any ideas? Or is there a way to reset the factory settings without a scan tool? Thanks for any help.
Use INPA on a PC go to Chassis_ 1 axle air suspension_activate_set mode_production mode_back_hand control (use axle and/or left and right raising/lowering [RA UP RA DOWN RL UP RL DOWN RR UP RR DOWN AND OFF] to get height on both sides where you want it. Requires measuring and getting out of car several times to get it right_ back_calibrate_f8/abgleich [pop up window "calibrate vehicle height" should say left 0 right 0_hit ok-(you will see offset and counter values with numbers - or +_ hit f8/abgleich again_ pop up "calibrate vehicle height" left 0 right 0_ hit ok (offset values should read left 0 right 0 in both rows, counter values in the middle with x#)_back_modes_ e-saveMod OFF ( production mode should be off) _ back. Exit Play around with it. Don't completely quote me on this but it has worked for me.
for my Porsche Cayenne GTS . I red that with the AUTEL DIAGNOSTIC TOOL , it’s possible to lower the car , about the Porsche Program ( normal , lower , higher ) so you can choose, like before the changes, to have your Porsche , when you put on SPORT, a better lower setting, that permit you to go on a Highway , with less gasoline consumption …
Hi Francisco Thanks for this video. I dont have the code reader you have. So question is: I have a BMW 530d GT, can you tell what the normal ride height should be for my car its F07 '2013.? That would be great It was running nromally until mid winter then it started to drop for some reason, evenly both sides. BMW pumped it up full, to check for leaks, but there are none as still at full height. I say that, I loaded the boot with about 50kg and it dropped about a 10mm. I have been trying to find out information about what situations turn on the compressor to keep at right ride height. Tried with the ride switch, Eco-Comfort-Sport and the DCS Hiope to hear back from you soonest Antony
Hello friend I bought a new air sensor and after connecting it, the car became shaking, and while pressing the accelerator pedal, there is no torque in the car, after that, the car stopped working, my friend, does the new sensor need programming??
Hi. I have done this twice. I dropped the air suspension. But after parked up after driving. When I start car next day it goes back up. Can you help. Thanks
Just to follow up on this question-I am working on an 03 X5 with my Foxwell 510 and it is allowing me to adjust my rear suspension. This is a great scanner that is inexpensive and allows me to do so much on my 4 BMW's. Highly recommended.
What would you suggest for the air ride not coming on after the shop charged me $3,866.14? And it still isn't raising up or off the tire! Please help me!!!
I’m trying to input the values but the ICM says it’s unsuccessful and won’t go on to adjust ride height. Also, the codes my ICM is showing won’t clear. Any ideas?
Hola Cómo está espero que esté bien con salud en familia tengo una BMW x5 f15 le puse la bolsa nueva las dos atrás le cambié el compresor todo bien atrás la que libre todo muy bien pero todavía mi carro no es que se va simplemente del lado derecho tiene media pulgada menos que la del lado izquierdo no sé qué hacer quiero tu consejo por favor gracias
Sorry but you are measuring from the wrong datum. Forget anything about tyre pressures, that does not make any difference if you measure from the BOTTOM of the wheel rim.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Center of wheel arch to lower lip of rim according to bmw manual, not like you measured.
Brother me estan ayudando tus videos enorme mente...gracias
Gracias por esto.
Cómo puedo saber si necesita calibración o si es el compresor, o si es el absorber?
Gracias
Can you do this calibration in e61 2010? 520d?
2010 750li. One side is about 3” higher and the other side looks normal. I drained both air shocks to lower completely and when I cut on the car, it went to normal height. After 15 minutes I opened the door, the compressor came on and raised the right side the additional 3” for some reason and that is where it’s staying. Any ideas? Or is there a way to reset the factory settings without a scan tool? Thanks for any help.
Thanks
Where is a good place to order some shock for 2009 750li
Hi I have a 740i and it’s low in the front and my level button don’t want to come on what do that means ?
Use INPA on a PC go to
Chassis_ 1 axle air suspension_activate_set mode_production mode_back_hand control (use axle and/or left and right raising/lowering [RA UP RA DOWN RL UP RL DOWN RR UP RR DOWN AND OFF] to get height on both sides where you want it. Requires measuring and getting out of car several times to get it right_ back_calibrate_f8/abgleich [pop up window "calibrate vehicle height" should say left 0 right 0_hit ok-(you will see offset and counter values with numbers - or +_ hit f8/abgleich again_ pop up "calibrate vehicle height" left 0 right 0_ hit ok (offset values should read left 0 right 0 in both rows, counter values in the middle with x#)_back_modes_ e-saveMod OFF ( production mode should be off) _ back. Exit
Play around with it. Don't completely quote me on this but it has worked for me.
Good thanks
Great job ... great explanation! Thx
Where u located ? How much do u change to do this ?
hey Julio, when you say put low numbers, it's based on the measurements that the scanner gave you, not the ones you took, right? or am I wrong?
What tool to use for x5 calibration?thanks
for my Porsche Cayenne GTS . I red that with the AUTEL DIAGNOSTIC TOOL , it’s possible to lower the car , about the Porsche Program ( normal , lower , higher ) so you can choose, like before the changes, to have your Porsche , when you put on SPORT, a better lower setting, that permit you to go on a Highway , with less gasoline consumption …
Hey brother where can i get that scanner
Hi Francisco
Thanks for this video. I dont have the code reader you have. So question is:
I have a BMW 530d GT, can you tell what the normal ride height should be for my car its F07 '2013.? That would be great
It was running nromally until mid winter then it started to drop for some reason, evenly both sides. BMW pumped it up full, to check for leaks, but there are none as still at full height. I say that, I loaded the boot with about 50kg and it dropped about a 10mm.
I have been trying to find out information about what situations turn on the compressor to keep at right ride height. Tried with the ride switch, Eco-Comfort-Sport and the DCS
Hiope to hear back from you soonest
Antony
Where your shop.
Nice!
Hello friend
I bought a new air sensor and after connecting it, the car became shaking, and while pressing the accelerator pedal, there is no torque in the car, after that, the car stopped working, my friend, does the new sensor need programming??
Hi. I have done this twice. I dropped the air suspension. But after parked up after driving. When I start car next day it goes back up. Can you help. Thanks
هل ينطبق ذلك على سيارة 760li e66
Model 2003
I have a 550 I did a calibration and now the left is very low and the right is higher any suggestions I will appreciate
Do you have to have that specific machine/device in order to adjust the rear, or can it be done with another one that's just as easy and efficient?
Just to follow up on this question-I am working on an 03 X5 with my Foxwell 510 and it is allowing me to adjust my rear suspension. This is a great scanner that is inexpensive and allows me to do so much on my 4 BMW's. Highly recommended.
@@davesmith6128 Much appreciation!
Can we use ista bro
What would you suggest for the air ride not coming on after the shop charged me $3,866.14? And it still isn't raising up or off the tire! Please help me!!!
JULIO, I FOLLOWED YOUR INSTRUCTION. BUT THE TIRE STILL DOWN. POSSIBLE COULD BE HEIGHT SENSOR ISSUE? NEED HELP
Pls I watched your video over and over I still have head to to adjust my bmw x6M ride height you said put lower number it will raise right
yes
Hello i have x6m
Which tools did you use?
Thank you
I’m trying to input the values but the ICM says it’s unsuccessful and won’t go on to adjust ride height. Also, the codes my ICM is showing won’t clear. Any ideas?
I change my 2 rear schocks an compressor one side goes all the way up in the air?
Hi you fix that issue?
Can X5 e70 can be calibrated or only 7 series ?
I changed my rear air struts an it’s still sagging what could it be?
Do you know if this triggers check engine light? Because I coded my air suspensions yesterday and after like 4hrs my check engine light came on.
Check engine light has only to do with emissions and drivetrain issues. Not chassis parts. Check fault codes and proceed from there.
I have problem on me f01 730
On front one,but front no air suspension jus electrical one ,just after service put on ground she not in leavel
Where are you located
We are in the Inland Empire, CA ( Fontana, Ontario, Rancho cucamonga, Riverside, Colton, Bloomington, Rialto, San Bernardino, etc,... )
Hola Cómo está espero que esté bien con salud en familia tengo una BMW x5 f15 le puse la bolsa nueva las dos atrás le cambié el compresor todo bien atrás la que libre todo muy bien pero todavía mi carro no es que se va simplemente del lado derecho tiene media pulgada menos que la del lado izquierdo no sé qué hacer quiero tu consejo por favor gracias
Hey Julio is this the only scanner you can use to raise suspension?
You probably can do it with ISTA as well.
What about bmw 745 ? Is it the same ?
Do you have a link to where buy the air compression >?
Ebay
Sorry but you are measuring from the wrong datum. Forget anything about tyre pressures, that does not make any difference if you measure from the BOTTOM of the wheel rim.
That's correct sir
Hello sir I have bmw g12 model there's some problem to calibrate air level , kindly Shere your mail id to send you the errors details
does anyone recognize the scanner he used?
Solus Edge
Snap on tools, they only sell to industry professionals
Bro you are measuring in the wrong point of the rim!!!!
Wrong measurement
Thank you so much!!! Awesome video.