Hi, Previous owners had lowered the car in a bmw workshop. No fault with the air suspension. Is it possible to raise the car in factory settings with this program? Thanks
Hello mate, good video but the problem im having is im only getting ride hieght sensors im putting in diamiters and everything but nothing happens. Im not getting actual ride height adjustment just sensors when i follow your steps. Any solution. Thank you
HEY MK,,, i got f02 & jacked the car in the shop couple of times doing front control arms...etc, nothing changed in the rear, now the rear right side is lower by two fingers other than the left side! no leaks or continued pump operation....drove it for a bit still the same...no errors even on ista! what shall i do ? thanks appreciated 👍
Hi. If I have lowered front of the e61. And I put back original springs do I need to calibrate rear suspension or IT will does automaticly? Best regards Mate.
La calibration se réalise lorsque l’on remplace les coussin d’air Si ta voiture penche ou s’affaisse un changement des coussins est nécessaire Ne tarde pas sinon la compresseur d’air va fonctionner au maximum tout le temps et tu devras le changer aussi
I'm looking for the Sport Mode position feature for G12 (LCI). Where do I code it? My car is already lowered using ISTA but I want to edit the Sport mode position. Today it lowers about 10mm extra on sport mode. But where can I change it. Id like it to lower about 20mm in sport mode.
J Law Officially, you can’t use it to lower the car, but you can trick it by entering higher values, eg instead 73cm, you can enter 75cm, so it thinks it s higher than it should be, and it is going to lower it. This trick is going to lower the suspension, but it is not a suggested solution.
Hey how are u doing? Nice video thanks for posting it. I got this suspension level malfunction message on my x5 e70 . My car is not leaning on one side i mean is more like lifted on one side u know what i mean? I got no leaks on the air bags . I think its more like something with the sensors or something like that. Do you think that with that program ill be able to fix it?
Diego D if you are sure that you don’t have a leaking pneumatic spring, you should perform a diagnostic scan with ISTA, to find out exactly the error code, and then try to level it with this procedure
@@MKAutoTech thanks. I change the rear bags, but I feel a little saggy. I lost some handling. If you tell me what measure you have maybe i can fixed with ista d. Now I have 72.8 mm
Does this adjustment take place immediately or over time?
which version do you use for G. g11 series. g12
Is this funktion for g11 ok
Hi,
Previous owners had lowered the car in a bmw workshop. No fault with the air suspension. Is it possible to raise the car in factory settings with this program? Thanks
Hello mate, good video but the problem im having is im only getting ride hieght sensors im putting in diamiters and everything but nothing happens. Im not getting actual ride height adjustment just sensors when i follow your steps. Any solution. Thank you
Same😢
HEY MK,,,
i got f02 & jacked the car in the shop couple of times doing front control arms...etc, nothing changed in the rear,
now the rear right side is lower by two fingers other than the left side!
no leaks or continued pump operation....drove it for a bit still the same...no errors even on ista!
what shall i do ? thanks appreciated 👍
hi my friend i have a issue of bmw x5 it is work that i can use launch scantool because i dont have bmw scanner
Hi. If I have lowered front of the e61. And I put back original springs do I need to calibrate rear suspension or IT will does automaticly? Best regards Mate.
Hello, in what cases is calibration necessary? I don't have any problems, but can the vehicle break down over time after 200 thousand kilometers?
La calibration se réalise lorsque l’on remplace les coussin d’air
Si ta voiture penche ou s’affaisse un changement des coussins est nécessaire
Ne tarde pas sinon la compresseur d’air va fonctionner au maximum tout le temps et tu devras le changer aussi
Great vid, i’ve been battling with inpa for many days now. Where can I get this software?
what is the version of the software Rheingold 3.55.11 or 4.14.14
I'm looking for the Sport Mode position feature for G12 (LCI).
Where do I code it? My car is already lowered using ISTA but I want to edit the Sport mode position.
Today it lowers about 10mm extra on sport mode. But where can I change it. Id like it to lower about 20mm in sport mode.
which version of ista do you use for G. series. G11 G12
Is this just the calibration? Or does it have the capability of lowering suspension past factory specs? If so, do i just put the height(mm) i desire?
J Law Officially, you can’t use it to lower the car, but you can trick it by entering higher values, eg instead 73cm, you can enter 75cm, so it thinks it s higher than it should be, and it is going to lower it. This trick is going to lower the suspension, but it is not a suggested solution.
MKAutoTech awesome thank you for the reply 💪🏼✌🏼
The part I don't get is the instructions at 3:55 - Do I cycle the engine first or wait 10 seconds and then cycle the engine?
start the engine wait 2 seconds turn it off and wait another 10 seconds after that
Hey how are u doing? Nice video thanks for posting it. I got this suspension level malfunction message on my x5 e70 . My car is not leaning on one side i mean is more like lifted on one side u know what i mean? I got no leaks on the air bags . I think its more like something with the sensors or something like that. Do you think that with that program ill be able to fix it?
Diego D if you are sure that you don’t have a leaking pneumatic spring, you should perform a diagnostic scan with ISTA, to find out exactly the error code, and then try to level it with this procedure
Hi ,i lowered my f11 520 d 2013 front on eibach pro kit .What hight should be on rear suspensions ?
I have the same question. Eibach -25mm. What measures do you enter on ISTA for rear suspension?
Hi, i have a x5 xdrive30d f15 M kit with 20". I need the correct suspension height. I mean, from bottom of the rim to fender. Please help me!!!!!
RENE VALLE there is no “correct height”, if you have air suspension, this procedure will auto adjust the ride height
@@MKAutoTech thanks. I change the rear bags, but I feel a little saggy. I lost some handling. If you tell me what measure you have maybe i can fixed with ista d. Now I have 72.8 mm
RENE VALLE There is no correct height, but the normal is about 73 cm from the bottom of the rim, so I think you are ok
I try to set the suspension, but change every Day. Do you offer remote support vía team viewer?
Great video.
What kind of connection did you use? Enet , ICOM or?
rimmero16 In this case, a K-DCAN cable
Thank you very much man
I wish I can see up closer
Adjustable rear links it’s simple ..
thanks 😍😍😍
Brilliant