Replacing window regulator on rear door of 2000 Buick Century
HTML-код
- Опубликовано: 14 окт 2024
- Quick how-to on how to change a regulator for a power window. Regulators were purchased through 1aauto. www.1aauto.com...
Disclaimer:
Due to factors beyond the control of Chemical Spore, I cannot guarantee against improper use or unauthorized modifications of this information. Chemical Spore assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Chemical Spore recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Chemical Spore, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Chemical Spore.
This made the swap relatively easy! Just one bolt was a bit problematic going in the new regulator. Thanks, again!
Good job, I am happy that it helped!
Thanks for the video, simple
Currently while watching your video I’m working on replacing my window this has been very very helpful thank you very very much for doing this
Correction my window power motor thingy I’m tired it’s been a long day forgive me but thank you again
@@jeanheltonandkids.8709 you are welcome. Subscribe for more content
Great video. One point you should make is that the assembly may go in upside down. I spent a few hours last night trying to install something that was upside down. I was in a hurry and could only find a regulator without a motor. At that point I started to wonder if the part was correct, if I had mounted the motor in the right position and so on. This morning I went over the video and found out that I had reversed the mounting position. I was able to do it and finish in a relatively short time. If you can show how the motor is positioned and which side goes where. Thank for the video it helped a lot.
I didnt think of that problem cause I never came across it.
Thanks for the quick video! Headed out to tackle this project right now
Good job! You got me confident enough to do my own
Super easy 👌
Thank you, thank you, thank you.. 👍🎉
You are welcome.
Great video, I'm replacing one today and wanted to know what to expect.
Good luck buddy, let me know how it goes.
Its why were all here 😂🤔
@@jeffnpatricia true! Lol it went very easy
Great job using only one hand! I can do this now.
Believe
Your the best bud,, 👍
I'm not the best. But i love to help
Thanks
Thank you for the quick informative info.
You are welcome
That middle hole at 2:45 looks very familiar 😂. I just drilled the same hole to screw the regulator parts together so the window stays up.
Nice video. I wish the Camaro had that much room
I know, it's too tight. Rediculous
Would the front driver side be similar? (Other than the extra electrical stuff for the windows)
It is almost exactly similiar. should not be any harder than the back
Did you put any high temperature grease on the track's
No, tracks were prelubed
silicon spray of some sort i got it off flea bay
Great Video Wish you had also focused on putting the door panel back on. Just paid a small fortune to have mine repaired but there is still a Large gap where the panel dosen't meet the frame.
Terribly unhappy.about that. I was hoping this video would show me the process so I could conduct a reasonable discussion to get it fixed properly.
Its pretty much in reverse of taking it off. Didnt mean to dissapoint anyone. Thanks for watching.
Hard plastic plugs push into holes in the door to hold the plastic. Look from underneath and you should be able to see the white plastic plus and where they should have been pushed in to fit tightly. Watch the first few minutes of the video if you want then pause & try it yourself. You can do this!
Should u do both sides at the same time, both windows?
I did 3 windows. They all didnt work except driver window.
@@chemicalspore , so its not nescary to do all at same time?
@@chemicalspore also did u order yur parts from autozone, i notice alot of the descriptions for location contradict from the link to actual specs. In decription
@@suzuki4512 no, check out 1aauto.com
Can anyone tell me does the rear windows roll all the way down or half way down?
Should be all the way
these friggin motors get all twisty. had 3 out of 4 fail (-_-) 1 replaced so far lol
Them crappy cables
@@chemicalspore every time! smh you just hear that crunchy twist and thats all she wrote. mine snapped at the bottom of the window guide so the window just slid into the door. at least it was a nice day when it happened
4th one went out about a month ago haaahahaha
@@cthulpaspawn Shiiiiid
special silicon lube for the window channel so the window goes up/down easier???? oil the little tubes so the thing in them is really really lubbed up??? so NEVER EVER have to do it again???
Maybe the owner was selling the car???? Maybe she only paid me for the basic labor???? Maybe you can find another way to be an asshole???