Jak dla mnie, pełny profesjonalizm! Szacuneczek za czystość i porządek dookoła! Wzór do naśladowania dla innych! Szczególnie dla Polaków, bo skandalicznie zaniżają poziom.
Hi Maciej. What a good job mate.can i ask how many kms you have driven since your rebuild of that engine? Any problems until now ? Do you see any shavings?
Have you checked the geometry of the cylinder block? It is believed that the cylinder block also deforms under load. What was the mileage on your car before the repair? Thanks..
I have checked the block, i did not spin a bearing, just found metal shavings and did this preventetively. Car was at 260k kms, done 13k since so far so good
What was the issue for it to be rebuilt? my 640d will need the same rebuild, but i dont know how bad t is inside the block as been knocking sounds are loud
Nice job, but - I think You should also replace the oil cooler - some of this meal shavings can stay at this place. Also are You sure is your block is straight and all bearings are concentric? I hope yours engine works well, regards.
@@maciejcymerys191 change oil valves in filter housing, if not , engine have dry start at every morning, and damage crankshaft... first goes out 135 end bearings.
Czesc.U mnie N57 w F11 2015 rok od nowosci.Dopiero co prawda 100k km nalotu ale predzej czy pozniej bede musial robic rozrzad+ pompa wody.Widze po blachach ze Eire.Czy rozrzad tez robisz i jaki koszt wymiany.Zamawiasz sam rozrzad dla klienta czy ja mam sobie sam zamowic +pompe wody?Pozdrawiam z co.Wexford
Czesc, niestety nie oferuje takich uslug to tylko przy wlasnym aucie to robilem. Mam za duzo na talerzu na ta chwile zeby w silniki sie bawic. Napisz do mnie na fb to ci polece kilka osob w irlandii
@@maciejcymerys191 I had the same issue 535d f10 spun main bearing fix it very accurately plasticgage new bolts spun again in 5000km I bought a new engine and that fixed the issue 😂😂😂
Every crank journal has its own tolerance lasered on the block. There are bearing sets with all the same dimensions, but as much as I know you need to lookup the numbers on the block to determine which actual bearing size you need.. i hope your engine will last forever, it was a lot of work! edit: this is what i mean, here it is all bearing size 2: ruclips.net/video/de-UdtVROgI/видео.html
Yes block and crankshaft both have their own numbers to tell which bearing size you need. Bearing sets are for conrod bearing i dont believe there are sets for main bearings as theyre all sold individually. All was done according to ASO instructions either way same as in the link you posted
dude, do you even understand what you doing? bolts needs to signed. litereally everything should be backed into it is place. i cant see this. it is physically hurts
Hi Maciej. What a good job mate.can i ask how many kms you have driven since your rebuild of that engine? Any problems until now ? Do you see any shavings?
10K Kms update: Car running great, oil change 1k ago no glitter. Hopefully it lasts.
Hows it holding up? Hope it lasts 100k for you! I'm tempted to get a spare engine just because i dont trust the n57 bottom ends!
What mileage was your failure?
Brawo Maciej !
Amazing work, congratulations
Great work. The chain guides were upadated , the ones you have on go brittle and break
That's one hell of a job, well done! 👌
And that in-line 6 sound... man there's nothing better! 💪
Jak dla mnie, pełny profesjonalizm! Szacuneczek za czystość i porządek dookoła! Wzór do naśladowania dla innych! Szczególnie dla Polaków, bo skandalicznie zaniżają poziom.
What the hell do u mean buddy?
super robota, pozdówki z filmu Chrisa
Not that long ago, BMW 3.0 diesel engines were known for reliability. Now it seems that 2.0 diesels are more reliable than 3.0.
They were with the M57 very very tough engine this N57 has had alot of problems
My n57 Didnt Give me one problem
@@DenisLuca-g5v it will, around 250-300k km
M57 is bullet proof...n57 is strong...and n47 is a disaster..
Mine holding out really well too but then I have been obsessive with oil and filter changes around 6000m so hopefully it keeps going 🤞
Respect,Nice work
Hi Maciej. What a good job mate.can i ask how many kms you have driven since your rebuild of that engine? Any problems until now ? Do you see any shavings?
@@justysone100 hi, its done about 20k kms since, no more shavings, wife uses it daily for work commute, roughly 50kms a day.
Good job
Hello, is that new cranckshaft original or copy? Thanks, and don't ask me why i'm asking :D :D
@@mukii2969 covered in the comments multiple times. Genuine bmw, cheap replicas do not last.
Have you checked the geometry of the cylinder block? It is believed that the cylinder block also deforms under load. What was the mileage on your car before the repair? Thanks..
I have checked the block, i did not spin a bearing, just found metal shavings and did this preventetively.
Car was at 260k kms, done 13k since so far so good
did you find what was the cause for the metal shavings ? did you discover these in the oil filter ?
its in the description. Crankshaft wobble.
yes found in oil fitler during maintenance.
Great work
Awesome! Well done!
Sehr gute Arbeit😎👍
Haters gona hate. I'lll love to do that kind of maintance
Did you have to resurface the head or the block for this repair?
mine were very straight, ideally i would but dont ahve any trusted workshops around me to leave that to.
no new piston rings?
No just reused old ones
What brand bearings did you use?
@@kingGar27 genuine
What was the issue for it to be rebuilt? my 640d will need the same rebuild, but i dont know how bad t is inside the block as been knocking sounds are loud
Did you even check cylinder wear before honing them?
Can you do this job Georgie boy? I doubt It...i saw video that you buy new used engine directly...so shut up please...
they were checked i bought a digital dial gauge for this exactly. i didnt film everything some of the stuff is boring.
What mileage had the engine covered at this point please? Nice video. Well worth documenting your work. 👍🏻
coming up on 260k kms
How has it been since the rebuild?
@@wass006 25ks now going good.
How long it took ?
Witam. Co to za preparat, którym spryskujesz cylindry podczas honowania? Dzięki z góry za odpowiedź .pozdrawiam. dobra robota.
dobra robota !
What was the mileage on this ?
260k kms
So mine at 85k Miles should be ok yet?
Bravo! 👍👍👍
Nice job, but - I think You should also replace the oil cooler - some of this meal shavings can stay at this place. Also are You sure is your block is straight and all bearings are concentric? I hope yours engine works well, regards.
Thank you, i checked block is straight and measurments correct, i did fail to replace cooler but it will be done soon.
So far it works.
Thank you
@@maciejcymerys191 change oil valves in filter housing, if not , engine have dry start at every morning, and damage crankshaft... first goes out 135 end bearings.
Dał redę zmienić pompę oleju na samochodzie bez zrzucania skrzyni?
Pozdro
Well done ,from where did you buy the crankshaft ?
From BMW directly. Crankshaft had 0.006mm run out on main bearing journals
@@maciejcymerys191 is it cheap in your country ?
@@brahim55 crankshaft was 2500 euro
hi, can you tell me the brand of the crankshaft you bought?
Genuine bmw only, all others wont last
Cześć Maciek
Gdzie kupiłeś wał i panewki i ile kosztowały?
Wszystko ORI z ASO.
2.5k euro za wal.
Panewki jakies 30 cos euro za sztuke.
Rod bolts needs put new ones not put old ones back . They are stretching
The old screws were only used to check the play on the shaft, didn't you notice?
Czesc.U mnie N57 w F11 2015 rok od nowosci.Dopiero co prawda 100k km nalotu ale predzej czy pozniej bede musial robic rozrzad+ pompa wody.Widze po blachach ze Eire.Czy rozrzad tez robisz i jaki koszt wymiany.Zamawiasz sam rozrzad dla klienta czy ja mam sobie sam zamowic +pompe wody?Pozdrawiam z co.Wexford
Czesc, niestety nie oferuje takich uslug to tylko przy wlasnym aucie to robilem.
Mam za duzo na talerzu na ta chwile zeby w silniki sie bawic.
Napisz do mnie na fb to ci polece kilka osob w irlandii
@@maciejcymerys191 oo super wielkie dzieki,na FB jestes pod tym imieniem i nazwiskiem191?
@@inspired_by_bimmer267 mcoding poszukaj na fb
@@maciejcymerys191 ok dzieki znalazlem ich juz.
@@inspired_by_bimmer267 to ja jestem mcoding tam napisz polece ci kogos
Hi Maciej, Admirable work. My Irish reg’d F06 has 143,000km. I will need to change the timing chains etc sometime. Do you work on other people’s cars?
Did you leave the gearbox in the car or take it off?
What was the total parts wise?
Hi where are u in Ireland
Well done buddy how long take you to do the job?
3 weeks due to wait for parts
@@maciejcymerys191 any issues since the rebuild?
@@ciucavasile2178 5 oil changes in / 2000km and still seing glittery oil. Car runs perfect though. Will see
@@ciucavasile2178 most likely due to not changing oil cooler
@@maciejcymerys191 I had the same issue 535d f10 spun main bearing fix it very accurately plasticgage new bolts spun again in 5000km I bought a new engine and that fixed the issue 😂😂😂
What's the cost of parts nd labour
He's doing the labour himself lol
nice one boy!
sealer applied incorrectly. you gonna end up with shit inside an engine which is sealer lefovers when squized
Those jacks looks a bit unsafe to be working underneath 😊
Every crank journal has its own tolerance lasered on the block. There are bearing sets with all the same dimensions, but as much as I know you need to lookup the numbers on the block to determine which actual bearing size you need.. i hope your engine will last forever, it was a lot of work! edit: this is what i mean, here it is all bearing size 2: ruclips.net/video/de-UdtVROgI/видео.html
Yes block and crankshaft both have their own numbers to tell which bearing size you need. Bearing sets are for conrod bearing i dont believe there are sets for main bearings as theyre all sold individually. All was done according to ASO instructions either way same as in the link you posted
Btw Im pretty sure anyone who had to do bearings on this engine has seen this video
I think you have too many decimal places in your runout specification. Actually, .006mm is well within the manufacturer allowed tolerance.
Yes i ment 0.06mm, max acceptable runout is 0.02mm, ive mixed mm with inch decimals
major issue with these engines is bottom end and timing chains
before putting gaskets, lube them first!
Bad crankshaft for just 0.006mm runout? Can't be true, that's 6 micrometers!
Far beyond most machining capabilities, even a dust particle is larger!
@@dabyd64 who said anything about machining?
@@maciejcymerys191 I mean factories can't produce parts with such extreme tolerances. Maybe you wanted to say 0.06 instead 0.006?
@@dabyd64 yes must be my mistake. Well spotted.
never wait more that 5 seconds, because otherwise you going to burn the starter
dude, do you even understand what you doing? bolts needs to signed. litereally everything should be backed into it is place. i cant see this. it is physically hurts
Go do one. all internal bolts were brand new, you cannot reuse bolts as theyre stretched. youre ten steps behind
bare hands with no gloves and long women's hair on open block yikes.....
lol ever heard of an oil filter? and what have bare hands to do with anything.
Synthetic oil does not cause eczema as quickly as cold meats from Morliny or Sokołów
Shittybmw
Very insightful
Hi Maciej. What a good job mate.can i ask how many kms you have driven since your rebuild of that engine? Any problems until now ? Do you see any shavings?