You always need to have a brush with you if the sprayer spots out the paint you brush it of fast so you dont have to sand it of later wich could be a problem if you are painting over the wall papers
Nice video, thanks. Could the problem with the knob getting stuck and then suddenly releasing (causing the blobs) be caused by it having collected paint? And therefore could be prevented by (better) cleaning it at the end of each day or painting episode?
the paint was drying at the tip while using the machine causing those blobs. I had to clean the tip every once in a while to keep it to a minimum. I think the only thing you can try and do to cut that out would be to use specific Wagner paint and thin it out as much as possible helping it to flow better.
Now I'm confused. You said at 12:50 that the blobs were caused by the button getting stuck and later kicking in. Now you say that they were caused by dried paint in the nozzle? @@thedutchhazard
There is speciaal paint you can buy to use with this machine, i think your results will be better with that stuff but i used normaal paint and diluted it as much as possible
1: prvo bojiti plafone, pa onda zidove. 2: Zidove i plafone, koji nisu prethodno bojeni, prvo bojiti toniranom(belom) podlogom ,ili belom bojom, pa tek onda izabranom bojom. 3: problem krutog creva mozesh reshiti komadom armature fi-10... do fi -20 , tako shto cesh crevo kreptrakom zalepiti za armaturu pa se nece uvijati.Baj.
Погрешно ! Прво зидове окречити, када се зидови осуше залепити заштитну фолију на зидове и плафон окречити. Зашто ? Ако плафон прво кречите, како ћете онда плафон фолијом покрити да га заштитите од крешења зидова ?
@@NeuSatz72 Josh davno pre tvog , a i mog , rodjenja , pametni ljudi su reshili taj problem . Za zashtitu plafona , a po potrebi i zidova , koristi se za poduzu letvu prihektan pravougli komad lesonita ( danas postoje i bolja sredstva . Poshto obicno sve pada odozgo na dople , a ne obratno , tako je lakshe prvo okreciti plafone , a poptom , koristeci opisanu zaashtitu , kreciti zidove . Tako je radjeno od kad se radi moleraj . E u danashnje vreme se cesto dogadja i obrnuto ?
I just bought the exact same sprayer and your video is perfect for me..so thank you for the video.
Hello. Are you satisfied with the paint gun?
Two things: first, use a primer on the walls so that they don't suck so much paint. Second, you have to thin the paint by 10%.
Thanks mate, I might buy one as well
You always need to have a brush with you if the sprayer spots out the paint you brush it of fast so you dont have to sand it of later wich could be a problem if you are painting over the wall papers
Nice video, thanks.
Could the problem with the knob getting stuck and then suddenly releasing (causing the blobs) be caused by it having collected paint? And therefore could be prevented by (better) cleaning it at the end of each day or painting episode?
the paint was drying at the tip while using the machine causing those blobs. I had to clean the tip every once in a while to keep it to a minimum. I think the only thing you can try and do to cut that out would be to use specific Wagner paint and thin it out as much as possible helping it to flow better.
Now I'm confused. You said at 12:50 that the blobs were caused by the button getting stuck and later kicking in. Now you say that they were caused by dried paint in the nozzle? @@thedutchhazard
I'm mixing two things, It has been a while since I made that video 😂 but you're correct, I think it would help if you'd clean the machine better.
Thank you for the video.
Glad you liked it
Thx for the great video. Did you have you to use any special paint and did you have to dilute it ?
There is speciaal paint you can buy to use with this machine, i think your results will be better with that stuff but i used normaal paint and diluted it as much as possible
@@thedutchhazard Je hoort de verf NIET te verdunnen. Met verdunde verf gaat ie stotteren/pulsen.
1: prvo bojiti plafone, pa onda zidove. 2: Zidove i plafone, koji nisu prethodno bojeni, prvo bojiti toniranom(belom) podlogom ,ili belom bojom, pa tek onda izabranom bojom. 3: problem krutog creva mozesh reshiti komadom armature fi-10... do fi -20 , tako shto cesh crevo kreptrakom zalepiti za armaturu pa se nece uvijati.Baj.
Погрешно ! Прво зидове окречити, када се зидови осуше залепити заштитну фолију на зидове и плафон окречити. Зашто ? Ако плафон прво кречите, како ћете онда плафон фолијом покрити да га заштитите од крешења зидова ?
@@NeuSatz72 No koment .-
@@NeuSatz72 Josh davno pre tvog , a i mog , rodjenja , pametni ljudi su reshili taj problem . Za zashtitu plafona , a po potrebi i zidova , koristi se za poduzu letvu prihektan pravougli komad lesonita ( danas postoje i bolja sredstva . Poshto obicno sve pada odozgo na dople , a ne obratno , tako je lakshe prvo okreciti plafone , a poptom , koristeci opisanu zaashtitu , kreciti zidove . Tako je radjeno od kad se radi moleraj . E u danashnje vreme se cesto dogadja i obrnuto ?
Did you thin out the paint before hand? Im wondering if it needs thinning or not ☀️
I did with water as much as I could according to the instructions of the paint
Jak moc to práší
Zeg dit toch gewoon in het Nederlands man, er zijn Engelse review's genoeg .....