So does the Helper work for the Welder as in the company your doing the work for pay the Welder and Welder pays the Helper or what? Also along the same line does the Welder have to have a Helper and if he doesn't, does the Welder make more since there isn't a Helper?
Cary Stone some companies don't provide helpers. Or let them on the job. My thoughts on that is if the welders not making sparks he's not making the company money. But on the job we have there is two options for the helper welder. The company pays them. Which is usually less because they will usually provide FR clothing insurance and take care of the taxes. If the welders pay them we usually bill it as a 1099 so basically they are there own company and when we fill our tickets the company pays us an extra 20.00 for the helper. So instead of 70.00 he for the welder it would be 90.00hr and the welder will pay the helper out of that. Hope that helps
Retired Boilermaker was at a nuke plant for steam generator change out and took some drain lines out of the storage container and set one end on the gravel ground and leaned the other end against the container and some blow job inspector chewed me out for putting one end in the gravel screw him I'm going to prep the end before I weld it.ass holes just like to run their mouths
I'm sure your cap would look much better it you used two hands and just had your helper roll the pipe for you. guessing your using 5/32 for the cap? cool vid
Not trying to hate on pipeliner. But I weld here in ca were you gotta fit pipe for a living and run that LH. Sometimes we get these pipeliners that show up in these fancy trucks and they can't fit or even two hole shit they last about a week before being ran off. I just don't understand how they survive as a welder.
He did a video on it recently. He chucks it in the roll out wheel, checks for level, then comes to the end with the flange. He places a jackstand under the flange, checks the two hole for level and then splits the high/low based on the inside of the pipe. Uses a sawzall blade to gap it
Jacques Chevrier thanks! I haven't seen all his videos, yet. Haha. I appreciate the rundown! I was just getting ready to go and watch more of Jacob's post!
Приколы
Sweet welds Jacob. You are the man. Thank you.
Starting welding school Monday! So excited!
dude super stoked for you man keep in touch
Well? Hows life?
You guys have it all together, great welding, grinding, and "video-ing". Thank you for making this video available.
man we appreciate the comment thank you
Y'all are killin it Jake & Jed! Love it brotha!
thanks Jprdan we really appreciate it
put a welding shade lens on the camera , so that we can see your weldings better.
I'm jealous
Good job I like being on job sites with ones like y'all good attitude keep up the good work
Jacob, im sitting here doing a white collar job that i hate watching you having fun, thanks for sharing your time with us, God bless
keep the videos coming yall do a good job like the on the job clips
we are trying to do more and more those
Nice video guys great team work
thanks Jay hes an awesome helper
God bless you Jacob
thanks Guy you to man
We need more Dan in these videos, he is a funny dude.
Hahaha I will let him know.
That was badass!!!!
Thanks Michael.
This made me realize how slow I was at grinding 😂
It would be really cool to get to work with you guys
man for sure Benton oif you ever get up here let us know we would like to meet you.
So does the Helper work for the Welder as in the company your doing the work for pay the Welder and Welder pays the Helper or what? Also along the same line does the Welder have to have a Helper and if he doesn't, does the Welder make more since there isn't a Helper?
Cary Stone some companies don't provide helpers. Or let them on the job. My thoughts on that is if the welders not making sparks he's not making the company money. But on the job we have there is two options for the helper welder. The company pays them. Which is usually less because they will usually provide FR clothing insurance and take care of the taxes. If the welders pay them we usually bill it as a 1099 so basically they are there own company and when we fill our tickets the company pays us an extra 20.00 for the helper. So instead of 70.00 he for the welder it would be 90.00hr and the welder will pay the helper out of that. Hope that helps
Do you have to 2 hole the alignment to the flange on other end of the pipe? Or is it a flange and plain end?
I'm guessing you can tell how low or,high you need by the keyhole ?
Certainly a continuation of the great vids... The effort is appreciated... Those flange faces face down in the dirt though :(
hahahah we will work on that
Retired Boilermaker was at a nuke plant for steam generator change out and took some drain lines out of the storage container and set one end on the gravel ground and leaned the other end against the container and some blow job inspector chewed me out for putting one end in the gravel screw him I'm going to prep the end before I weld it.ass holes just like to run their mouths
looks like a stinger v
Its a great stinger man last forever
How do u guys like 7010 for down hill. I'm a steam fitter welder and we use 7010 for our root pass uphill and 7018 hot and cap uphill.
it welds good i like the 7010 pipeliner better but its what the job requires so i just do it lol
I'm sure your cap would look much better it you used two hands and just had your helper roll the pipe for you. guessing your using 5/32 for the cap? cool vid
You get used to it after awhile and can really slick one on. thanks for watching
Not trying to hate on pipeliner. But I weld here in ca were you gotta fit pipe for a living and run that LH. Sometimes we get these pipeliners that show up in these fancy trucks and they can't fit or even two hole shit they last about a week before being ran off. I just don't understand how they survive as a welder.
War Daddy I’ve met a few of those. They run the mainline and leave. All they know is drop and weld
Greetings for turkey ✋✋✋
love it thanks for watching
Where is this? What kind of terrain? Where is all the vegetation? It looks like mars.
hahaha its colorado
Do you know of any work over around Wv or Ohio? Caught a layoff yesterday.
WVClassicLincoln13 I don't man sorry but I think that's where I'm headed if I get laid off
What welder is that
What did you use to align the flange to the pipe, angel?
I think low amprs guys
He did a video on it recently. He chucks it in the roll out wheel, checks for level, then comes to the end with the flange. He places a jackstand under the flange, checks the two hole for level and then splits the high/low based on the inside of the pipe. Uses a sawzall blade to gap it
Jacques Chevrier thanks! I haven't seen all his videos, yet. Haha. I appreciate the rundown! I was just getting ready to go and watch more of Jacob's post!
James Valentine for sure man! Jake's a real stand up guy. I've learned quite a few things from him, not even just about welding either.
Jacques Chevrier 👌👌👌be safe brotha
Why don't you guys cap with 7018 down there? Everything's hippy it seems like
Michael Pederson because pipeliners cant weld up hill to save their fucking life.
Calvin Bostick lmao
man i like running uphill or Tig but the specs on this project calls for HYPI so i just do what they say.
Jacob Schofield do a tig video
elmajico361 some kid I’m my class welded a corner joint with 7018 downhill lol😂
what's the difference between a wendys pancake and sarge pancake?
not a lot i think the wendys are built a little better but they are also heavier.
чем удобна такая маска?
Was going on bro ! Put me down ! My brother is a rig welder we need work ! We got connections aswell brother. Please reply thanks for your time!
ivan adame what's going on brother just rolling through the comments replying. Where are you guys from? Email me at schofieldwelding@gmail.com
bead sounds undercut
sure is all the way around because you apprently you can listen to undercut LOL
G Loyd 😂????
Sounds undercut? 🤔🤔 lol
Yes, you can definitely hear the walls not breaking down... :)
u got a sa200 ???????
I have 2 SA 200 and a classic 300 HE
why not 8010 instead of 7010 ?
its just what the job calls for
I will alot of rod that was at 8010 it also was called hippie rod I believe you said 7010 or unless I misunderstood you
yes 7010 is (hyp rod) 8010 is called )70+
What's your insta?!
looks uggly welds
Hector Bejarano your spelling looks ugly, hahahahaha LOL!!!