RUclips is only good for searching up how to learn things other than that it's full of nothing...But gems like this is why I still am on here. This is one of those teach a man to fish things and I appreciate you for it 🙏🏾
A bad drain pump or clogged filter can also cause the drum not to spin .. and it's a very common issues as well .. should've been added to the 5 top ... the controller would be the last point to check .
I should start making repair videos. As a technician the main cause I see on stator motor style, is Bad SPEED SENSOR. Which is attached to the stator. It’s a 10-15$ part.
I just moved my front loader to a new home … it’s spinning but goes on forever .. as if it’s unbalanced .. I’ve taken almost entire load out .. doing the same .. It went from 7 mins left back up to 15 … any thoughts? 🤙🏼
@@calidazeable check ur drain catch for blockage.. make sure ur drain hose isn’t goin to far down the drain pipe. Make sure the holes in the rubber gasket aren’t clogged.. those are thing u check before we deem it a bad control board
Needs some help here😢 my samsung washer don’t spin and stock at 9 minutes after draining. Pump motor can be heard running but the drum doesn’t spin! Any thoughts on this? TIA
I fucking love you!!! The belt wasn't broken , but it was just laying inside the washing machine. Don't know why , just rented this shitty whole. Thank you!!
My frond load washing machine motor while washing rotate very slowly and heating the motor within 30seconds .bare motor take 6A load of spec. washing 93v 60w 580Rpm. what could be reason
So nothing on RUclips worked, so I did my own analysis. Looking at the board there were some dirty parts on the components traces. After cleaning it with robbing alcohol. It looked like one of the traces leads were rotten off maybe because of moisture or dust. I used my phone camera to zoom in 10x times it's a realme xt phone. I saw that it's indeed disconnected so I took a small flexible wire. Used fine sand paper on it so the solder would stick to it easily. I also used the sand paper to expose the leads on the circuit board. After cleaning it with alcohol I soldered the wire to the board to make the jumper. I also noticed some of the components in the same area looked worn. So I took the heat gun put some soldering paste on the components. And covered any vulnerable plastic components with aluminium foil to help it not get burnt. After I use the heat gun to heat up the components, reflowing them it looked brand new. Plugged it in after and works perfectly.
Ge smart front load . It spins fast when it's empty . But I washed 1 Towel , and it will spin that 1 Towel but not fast . When it's " done" the towel is soaked dripping still . So it's not spinning the heavy out of it. Any thoughts?
I have a Kenmore elite front load washing machine, when I try to wash it on Express Wash the washer stops and I get in 02 f code on the display and it doesn't spin
I have a samsung front loader which is not rinsing after wash replaced motor and pcb control board as instructed per repair still have issues after no codes shown, any ideas.
I actually clean the filter drain the water below before I saw this video I was proud of myself I thought maybe I fix the problem but the code keeps coming up early I keep draining the water out the bottom door it just won't finish the cycle of spinning and draining and now there is a loud noise in that door area
My GE front loader want start it goes directly to the last minute, it shows rinse on the screen, and the rinse doesn’t happen either and it turns off. Please help!
I have a Kenmore front loader machine that keeps stopping when it gets to the spin cycle if there are more then a couple of towels in the machine. it says "ND" on the screen.... help!
my kenmore front load washer gets to the 6th minute then wont finish washing it will will stay on 6 minutes for like 5-10 minutes then finish but will not go into its final stage where it washes rapidly?
Did you figure it out? Was it the control board? Mine does the same thing. Motor is good, drains good just sits there on 6min and doesn't go into high speed spin.
Yesterday, my washing machine wasn't spinning to rinse. After going through all the checks, realissed knob was accidentally set to zero. May be when cleaning it. So sometimes start with settings checks. 😊
I have a Samsung front load washer giving code 4E(water supply) I have tried a new water pressure sensor, my husband put in a new MCB. The water supply inlets have been changed. Samsung is the worst for repairs abd too many hoops to jump thru. Sears repair guy changed time twice in the same day, didn't come. It fills with water, then drains flashes code 4E but don't trigger to spin. My filter is clean.
7 лет назад+1
I have a Maytag front loader washer and dryer. If I put it on the fresh rinse and spin cycle it will spin, but on all of the upper cycles on the knob it won’t spin so I don’t think it’s the belt or the motor. It must be some kind of switch?
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
Had to stand on Samsung front loader drum (210 lbs) several times when fixing constant incoming water while unplugged. Now tub is not aligned with front door seal. Any suggestions?
hi can u please help me, I have a indisit washing machine and the drum doesn't turn at all but the belt and everything work on the rear. Just the drum doesn't move from the front. What do u think is wrong
My Hotpoint front load washing machine's belt slips regularly when machine start spining and drum stop working. Belt change works for some time but again it slips.Can someone give suggestions. Thanks.
That's exactly what the appliance manufacturers want everyone to do. Spend $800 - $1200 on disposable appliances that have to be replaced every 3 - 5 years.
Bought a belt, remove the back ,the belt is n it's place...washer Not spinning or even agitate,will get to o1 on timer & just keep running Will not stop. timer dose not move after after O1.juzt keep on running,unt I manually turn Off.Please Help!!!!
Same for me with my sumsang digital converter. It just drones while draining continues like that and don’t spin. Did you work out what was wrong with yours. With all that’s going on at mo, I can’t get anyone to come fix it All this hand washing over the bath is doing my back in😱
I have a samsung crysral washing machine serial no: 06SU53AG900047F. I replaced the inverter checked the belt filter is clean the drum turns left and right but it will not spin it stops at 9. Is there something else to check? Will appreciate if you can help
whirlpool sensation EX it spins clock wise ,after sometime time goes on but wont spin more.if i press pause button then reapeat it motor spins agin and stops again.any idea any body cud help.thankin you.☺
sorry to be so offtopic but does any of you know of a method to log back into an instagram account?? I was dumb lost the login password. I would appreciate any help you can offer me!
@Julio Zayd I really appreciate your reply. I found the site on google and im in the hacking process now. Seems to take quite some time so I will get back to you later with my results.
I give you more interesting puzzle: In wash mode device rounds the drum. After 1 min drum stop rounding and just shakes by motor. Load of machine is low. What it can be? BTW in "rinse and spin" mode drum again works as it should!
Mine will drain, but *usually* not spin. Rarely, it does, and it seems to do so reliably if it is empty. It is a direct drive model. I have replaced the drain pump and the door lock assembly. I have made sure the drain line is free. I'm honestly out of ideas. :-(
I have replaced the door lock but it still it will not spin with clothes in it. It worked when I just turn on drain and spin after replacing the door lock.
In other words when it doesn't work buy another one everything is made in china Mexico india and won't last long everything is made cheap and will break
Not impressed. His first solution is the belt. But if the machine has been washing rotating the machine back and forth, then the belt isn't broken! Unless it happened to break at some point in the wash cycle. I'd prefer a more step-by-step approach, and start with the most common reason, working on from there. Diagnose, don't just chuck out random answers.
You do know these videos are just giving you possibilities or general ideas of what is or what makes it function. That's up to you the home owner or technician to figure out.
My front load washer isn't spinning correctly. It will spin just never spins fast. It will spin slowly or even stop. It will stop and change directions, but never spins fast enough to pull water off close.
Lawrence Monlezun The problem depends on your model. Could be a few things such as a bad Clutch or timer/control board. If you have a direct drive motor with a rotor or stator then could be an issue with them or the sensors that may be attached. Could even be a motor control board too as it monitors speed of motor, but depends upon your model. If you are unsure of what features your model has then try entering your model # on their site & should bring up info related to your unit so you can see what kind of motor etc you have to check.
You're welcome! We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review We hope that you have a great day!
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
RUclips is only good for searching up how to learn things other than that it's full of nothing...But gems like this is why I still am on here.
This is one of those teach a man to fish things and I appreciate you for it 🙏🏾
Agree that is all it is good for.
A bad drain pump or clogged filter can also cause the drum not to spin .. and it's a very common issues as well .. should've been added to the 5 top ... the controller would be the last point to check .
The machine did the wash but did not finish last cycle. There was an obstruction and the pump is spinning but the motor is doing nothing,
Mine was as simple as cleaning out the small trap at the bottom. It had a coin and other debris.
You are correct
@@arriaga2019if your washer has a bottom panel to remove its fairly easy if not it certainly is a pain take off front panel to access it.
Thanks for this add-on because it was certainly my issue
I should start making repair videos. As a technician the main cause I see on stator motor style, is Bad SPEED SENSOR. Which is attached to the stator. It’s a 10-15$ part.
I just moved my front loader to a new home … it’s spinning but goes on forever .. as if it’s unbalanced .. I’ve taken almost entire load out .. doing the same ..
It went from 7 mins left back up to 15 … any thoughts? 🤙🏼
@@calidazeable check ur drain catch for blockage.. make sure ur drain hose isn’t goin to far down the drain pipe. Make sure the holes in the rubber gasket aren’t clogged.. those are thing u check before we deem it a bad control board
@@LastOneLeftt Thanks .. I’ll chk it out 🤙🏼
Thanks for the tip! Did you know we started a special technician professional program? You can check it out on our website at RepairClinic.com.
Needs some help here😢 my samsung washer don’t spin and stock at 9 minutes after draining. Pump motor can be heard running but the drum doesn’t spin! Any thoughts on this? TIA
U saved me, Belt was the problem but now it’s working, Thank you!
I fucking love you!!! The belt wasn't broken , but it was just laying inside the washing machine. Don't know why , just rented this shitty whole. Thank you!!
My frond load washing machine motor while washing rotate very slowly and heating the motor within 30seconds .bare motor take 6A load of spec. washing 93v 60w 580Rpm. what could be reason
If the belt is just off the pulley, check the bolt holding on the pulley. They are well known to work loose and cause the belt to slip off.
@ratpatrol thanks 🙏🏽 that’s exactly what happens to my washer I just checked it out and the belts is broken
So nothing on RUclips worked, so I did my own analysis. Looking at the board there were some dirty parts on the components traces. After cleaning it with robbing alcohol.
It looked like one of the traces leads were rotten off maybe because of moisture or dust.
I used my phone camera to zoom in 10x times it's a realme xt phone.
I saw that it's indeed disconnected so I took a small flexible wire. Used fine sand paper on it so the solder would stick to it easily. I also used the sand paper to expose the leads on the circuit board. After cleaning it with alcohol I soldered the wire to the board to make the jumper.
I also noticed some of the components in the same area looked worn. So I took the heat gun put some soldering paste on the components. And covered any vulnerable plastic components with aluminium foil to help it not get burnt. After I use the heat gun to heat up the components, reflowing them it looked brand new. Plugged it in after and works perfectly.
What machine? Mine did not finish final cycle. Found an obstruction in the filter but still no joy. The pump spins but the motor makes no noise
Ge smart front load . It spins fast when it's empty . But I washed 1 Towel , and it will spin that 1 Towel but not fast . When it's " done" the towel is soaked dripping still . So it's not spinning the heavy out of it. Any thoughts?
Hav same problem
Did you fix it? I have the same problem as you
My Samsung front loader washing machine stops mid way, doesn't complete the time cycle. What can you suggest sir
I have a Kenmore elite front load washing machine, when I try to wash it on Express Wash the washer stops and I get in 02 f code on the display and it doesn't spin
My lg F1480YD5 wont rinse and spin
cant believe it changed switch and it works like new thanks
I have a samsung front loader which is not rinsing after wash replaced motor and pcb control board as instructed per repair still have issues after no codes shown, any ideas.
Ours is doing the same thing gets to a certain point & then will stay there for a long time.
why my washing machine does not spin Samsung P1453GW/XEE
My automatic washing machine Samsung front loader model number wf 7600nas does not whant to spin
For me the belt had snapped and i replaced but when it spins it sounds like it dragging on something. Any advice please thanks in advance
My sharp automatic washing machine's spinning problem stop at mid cycle, it immediately proceed to washing without finishing the spinning cycle,
Same problem.. is the issue fixed?
I'm having this exact same problem as well. Did you get it resolved?
kenmore front load washer serial # XC32716687 will not go into high spin , it will drain and slow spin though
I actually clean the filter drain the water below before I saw this video I was proud of myself I thought maybe I fix the problem but the code keeps coming up early I keep draining the water out the bottom door it just won't finish the cycle of spinning and draining and now there is a loud noise in that door area
No refunds if they tell you wrong solution. Buy parts somewhere else. I learned the hard way.
My GE front loader want start it goes directly to the last minute, it shows rinse on the screen, and the rinse doesn’t happen either and it turns off. Please help!
I have a Kenmore front loader machine that keeps stopping when it gets to the spin cycle if there are more then a couple of towels in the machine. it says "ND" on the screen.... help!
I have same problem with kenmore front loader
Did either of you figure out the solution to this?
Whts the reason? Mine is also getting stuck.
"ND" stands for "no dice", meaning that the washer has given up the ghost.
my kenmore front load washer gets to the 6th minute then wont finish washing it will will stay on 6 minutes for like 5-10 minutes then finish but will not go into its final stage where it washes rapidly?
Did you figure it out? Was it the control board? Mine does the same thing. Motor is good, drains good just sits there on 6min and doesn't go into high speed spin.
I am having the same problem with my Kenmore washer. Did you ever get this resolved? Any help would be greatly appreciated.
Same problem
Same problem
Did you ever figure it out?
My washer does spin but not finish the cycle. We have to start the rinse and spin cycle. Please help
Yesterday, my washing machine wasn't spinning to rinse. After going through all the checks, realissed knob was accidentally set to zero. May be when cleaning it. So sometimes start with settings checks. 😊
What do you mean?
It indicates. DC mean what reason
Great video. This help me troubleshoot and repair without calling a repair man
Whirlpool Direct drive drive it won't let me open it's not to numbers linking P9 p3 do you have a Videos
My bosch washing machine not start it's automatically water coming out through exit hose
Samsung front load power on and off problem?
I have a Samsung front load washer giving code 4E(water supply) I have tried a new water pressure sensor, my husband put in a new MCB. The water supply inlets have been changed. Samsung is the worst for repairs abd too many hoops to jump thru. Sears repair guy changed time twice in the same day, didn't come.
It fills with water, then drains flashes code 4E but don't trigger to spin. My filter is clean.
I have a Maytag front loader washer and dryer. If I put it on the fresh rinse and spin cycle it will spin, but on all of the upper cycles on the knob it won’t spin so I don’t think it’s the belt or the motor. It must be some kind of switch?
Did you end up fixing your machine? If so, what did you do to repair it?
Good 👍
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Had to stand on Samsung front loader drum (210 lbs) several times when fixing constant incoming water while unplugged. Now tub is not aligned with front door seal. Any suggestions?
hi can u please help me, I have a indisit washing machine and the drum doesn't turn at all but the belt and everything work on the rear. Just the drum doesn't move from the front. What do u think is wrong
Did you find what was wrong after all? Have the same issue!
My Hotpoint front load washing machine's belt slips regularly when machine start spining and drum stop working. Belt change works for some time but again it slips.Can someone give suggestions. Thanks.
Hello I changed the roper lid lock and Shift Actuator. The lid lock still flash and washer still wont spin, HELP PLEASE.
Great video , it helped me
I have a ge front loader and it wont spin properly. Spin once, stop, spin than stop spinning
I have the same problem, how did you fix it?
@@cruiselover9903 I just got rid of it. Bought a new set.
That's exactly what the appliance manufacturers want everyone to do. Spend $800 - $1200 on disposable appliances that have to be replaced every 3 - 5 years.
I asked what to do if the Samsung washing machine doesn't spin actually this video states that what are the causes
Bought a belt, remove the back ,the belt is n it's place...washer Not spinning or even agitate,will get to o1 on timer & just keep running Will not stop. timer dose not move after after O1.juzt keep on running,unt I manually turn Off.Please Help!!!!
I have a whirlpool front load ,Emerson..great looking
Thku v.much it's working
Logik won't spin take water front load washer machine
The number one cause is issue with a drain pump!
Why is my samsung washing machine spinning the screen goose off
Number 1 Brushes?
Can i share a video??? It tries to spin..but doesnt
Same for me with my sumsang digital converter. It just drones while draining continues like that and don’t spin. Did you work out what was wrong with yours. With all that’s going on at mo, I can’t get anyone to come fix it
All this hand washing over the bath is doing my back in😱
How about turning off the bell!
Ifb spin not working
Could the control panel be faulty ?
I have a samsung crysral washing machine serial no: 06SU53AG900047F. I replaced the inverter checked the belt filter is clean the drum turns left and right but it will not spin it stops at 9. Is there something else to check? Will appreciate if you can help
This is great, but my anxiety went off the roof watching this video I’m too paranoid to even attempt this 😫
You can do it! We have individual part replacement videos that you can use as step-by-step guides after you troubleshoot the cause.
Maytage model number MFW9700sQ1 trouble code FO7
whirlpool sensation EX
it spins clock wise ,after sometime time goes on but wont spin more.if i press pause button then reapeat it motor spins agin and stops again.any idea any body cud help.thankin you.☺
sorry to be so offtopic but does any of you know of a method to log back into an instagram account??
I was dumb lost the login password. I would appreciate any help you can offer me!
@Kashton Ray Instablaster =)
@Julio Zayd I really appreciate your reply. I found the site on google and im in the hacking process now.
Seems to take quite some time so I will get back to you later with my results.
@Julio Zayd It did the trick and I finally got access to my account again. I am so happy:D
Thanks so much you saved my ass!
@Kashton Ray Glad I could help xD
Ok so I can't unlock the door it's jammed or something
The door lock is activated.
The washer I have sucks I hate it
And mine just REFUSES to suck!
Front loading washing machines are absolutely the best ever
Sometimes it will agitate or spin slow with a damaged stator and rotor
Joshua Ginnish You are wrong it clearly states in the video that if the stator and rotor are damaged the tub/drum will not move
@@stephensnell1379 "it may not" is what is said in the video.
On my LG washer it was the rotor hub. The splines are plastic so they were shredded. It was a quick 30 dollar fix.
fix it
I give you more interesting puzzle: In wash mode device rounds the drum. After 1 min drum stop rounding and just shakes by motor. Load of machine is low. What it can be?
BTW in "rinse and spin" mode drum again works as it should!
Too many problems just buy a second hand one
You are right. None of these problems is a simple fix except for replacing the belt
Gfwh2405l0mv GE washer machine doesn't spin
Mine will drain, but *usually* not spin. Rarely, it does, and it seems to do so reliably if it is empty.
It is a direct drive model. I have replaced the drain pump and the door lock assembly. I have made sure the drain line is free. I'm honestly out of ideas. :-(
I have replaced the door lock but it still it will not spin with clothes in it. It worked when I just turn on drain and spin after replacing the door lock.
The washing machine is a washing machine, but not spinning?
ooooo...
Jason Lim Lim u
In other words when it doesn't work buy another one everything is made in china Mexico india and won't last long everything is made cheap and will break
Not impressed. His first solution is the belt. But if the machine has been washing rotating the machine back and forth, then the belt isn't broken! Unless it happened to break at some point in the wash cycle. I'd prefer a more step-by-step approach, and start with the most common reason, working on from there. Diagnose, don't just chuck out random answers.
Sounds like you should make a vid
You do know these videos are just giving you possibilities or general ideas of what is or what makes it function. That's up to you the home owner or technician to figure out.
Agree, the first thing to check should be door lock, am I right?
They are trying to sell parts, thus the reason for the random parts replacement repair video.
Totally irrelevant 😞😞
How so?
My front load washer isn't spinning correctly. It will spin just never spins fast. It will spin slowly or even stop. It will stop and change directions, but never spins fast enough to pull water off close.
Lawrence Monlezun The problem depends on your model. Could be a few things such as a bad Clutch or timer/control board. If you have a direct drive motor with a rotor or stator then could be an issue with them or the sensors that may be attached. Could even be a motor control board too as it monitors speed of motor, but depends upon your model. If you are unsure of what features your model has then try entering your model # on their site & should bring up info related to your unit so you can see what kind of motor etc you have to check.
🦧👍
You're welcome!
We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
We hope that you have a great day!
Xqg80-q814de