He went from maybe it's just a loose battery cable, that would be amazing to, what the heck, the piston is missing. 😅😅 Never changed his tone, didn't lose it his 💩 This guy is awesome
It has been 5 months. Did you part it out? Buy another Chinese Hisun engine? or decided it wasn't worth anymore of your time? click a thumbs up if you want a followup also.
I’ve seen a lot of engine tear downs in my lifetime, but nothing ever like this. You couldn’t do that to the piston with a blow torch and hammer. Truly amazing.
Hmmmm, you have a battery that needs a charge or is possibly bad so you jump right to pulling the starter??? Then you pull a spark plug (still don't have enough voltage to even run the starter but you pull it just the same) plug is bent. Nothing in an engine will bend a plug like that so maybe when they were checking a no start engine they dropped the plug. However even though you still don't have enough power to start you go ahead and break down the engine. Noti g that the valves are fine no bad wear and tear on anything ahah! Piston is missing !!! Even though you had no reason to expect anything other than a dead battery (you need to show 13.5 volts at rhe battery to be good) so even though the oil is clean with no visible degree, no sign of heat distortion or virtually anything that would be indicative of a thrown rod or failed piston, cracked rings or anything . . . . You go straight to a tear down. . . . Some people will do anything for content. Small people with nothing real to offer.
@@zorrorides1 I gave up on this video after 13mins when he couldnt even use a multimeter properly and then thinks there is a drain in the system cos his charger chows 12.1v and battery shows 11.8v.
@@zorrorides1 'you need to show 13.5 volts at rhe battery to be good' Nope. The voltage of a car battery should be around 12.6 volts when fully charged and the engine is off. Between 13.7 and 14.7 volts with the engine running.
I am a retired internal combustion maintenance and repairs engineer and in my opinion that engine was held flat out in neutral till it destroyed its self. That’s after its original partial seizure. I love watching your videos and hope you have a very successful life. Regards Raymond 🏴
" I am a retired internal combustion maintenance and repairs engineer " Wow, thats a mouth full for a made up title. Typically Engineer designs things, not fixes them.
The clue is in the title on my apprenticeship papers. I will give you a clue 🤔maintenance. Not design. I have overhauled many many engines in my younger days And could still do it today. As long as someone did the heavy lifting 😂🏴👍👍
I've watched you work through a lot of simple fixes, but this is a good reminder to people that when you shop on craigslist, you never know exactly what you're getting. Most people would be at a total loss to fix this repair, my hat is off to you. 👏 EDIT: yeah, that piston will be fine, use some J-B Weld...LOL
@2vintage looks like Cub has a lot of parts available, you might make out ok. looks like the piston is about $200, and the entire cylinder head assembly is about $1k.
idk about it being a pile of poo .. my hisun 450 sector hasnt let me down .. ive jumped it countless times ,starts up in - temps and kicks ass for plowing the driveway and plow contracts at malls that i have @@catsbyondrepair
are they cast pistons? thats the only way i see this happening. there has to be others with the same problem. Edit, yes they are cast aluminum pistons. im surprised this isnt a more common issue on china motors.
yeah, right... Lil old couple just drove it to church on Sunday. WOW, never say that happen in all my years... Good luck. I hope you can fix it. This is a really interesting one.
I'd also like to congratulate you Joe on the 400,000k subscriber level you've reached,People obviously appreciate what you do as much as me,Onwards to half million 🤙
My father was a JD diesel mechanic his entire career… as with you he had a brilliant mechanical mind. I did receive that gene but your mechanical hunting skills are like his were…you folks are amazing
If you own a small wire feed welder here's a small tip......Don't struggle with the pain and aggravation of pulling and installing the engine. Put a .065 cut off wheel in your angle grinder and surgically remove the obstruction and weld the piece back in upon reassembly....I did this multiple times on Ford Econoline Vans 30 years ago.
Oh my god, that is hilarious! In my 45 years as a professional tech, I have never seen that level of crazy. Let me guess, the owner never heard a thing.
Tech: Did you hear anything weird when it stopped? Customer: Hear What I am half deaf, and it always makes this funny little noise, crash, bang, scrape, swish, crunch. As the head is eating the piston! lol I bet this guy never changed or checked any of the fluids on the thing since he bought it.
@@anthonymisell8845 i agree, rebuild this engine, he now knows what he is dealing with. another engine is begging for more work, nope, i'd rebuild this engine with all new/used parts.
Just bought a non running Royal Enfield Himalayan and when I took the head off it was the same situation. The piston had blown apart. Everything was unusable, head, cylinder, crank. I opted for a replacement engine as even the cases were banged up, plus the replacement engine was cheaper than a rebuild. Good luck!
@@pjm204 lol. My old girlfriend sold motorcycles at a dealer In Toronto. You would be surprised how many folks write off bikes within minutes of leaving a dealership.
I had a VW as a first car. Overall a good car but started loosing pressure. Took it to a mechanic to get it fixed. It ran really smooth until the intake valve got sucked into the piston (read through) when I was getting on the Freeway 2 blocks from my house. That thing sounded like a thrashing machine on a bad day. But the mechanic was honest and rebuilt it for free. He had misread his calipers. Owning up to a mistake brought greater respect.
i just found this video tonight and i was fully immersed in it. I look at your channel and i see no follow up video. bruh..it's been 4 months....bruh...i'm freakin' out ova here!
I took my first head off a briggs and Stratton in 1967 . I've done a thousand since then. And I never saw a crankshaft devour a piston like that. Awesome ❤. Always entertaining. Still worth 3500. The vinster can't even look at this catastrophic mess. Lol 😂. ❤❤❤
That is really unbelievable! Can't say I've ever heard of an engine digesting a piston. 🤣 Please keep the content coming! I have to say that even though I don't ride a motorcycle, ATV or UTV, I have really learned a lot about small engines from watching you patiently and methodically tackle each project. I have to also admire your mid-western good manners and patience having never heard a swear word on your channel. If it was me, you would have only heard minutes of bleeps during the inevitable setbacks. Great job!
Bro, Amazon has many MANY cheep boroscopes you plug into your phone, i got one for $20 with a light up end and it works awesome..... You should get one buddy.....makes life so much easier.👍👍
Iv niver seen anything like that in my life and I'm a machanic retired. the person who sold you that knew.he has Put a scope in the plug hole and seen there was no piston. Good luck buddy you will still come out on top.
I was wondering why he did not do a compression test and squirt some oil down the plug hole like he usually does. On the whole he is very good with carbs and trouble shooting. Do the testing first. A bore scope would have said a lot.
The ole disappearing piston trick. I've seen a lot of engine carnage, but never that. Usually when a piston lets loose like that there would be holes in the case. That's impressive!
first for me too, never seen anything like that before. musta disintegrated and not turned any further to spread chunks. seen a BSA twin with a wooden piston sold as not running very well
I used to work for MTD (Cub Cadet) and had this exact unit as a demo to engage dealerships to sell these machines. Hisun is the manufacture. Lots of issues with the wiring harnesses and lack of manufacture support, forced Cub to pull the plug on the Challenger 750 efi. I never had an issue with my demo and loved it. Hope you get it fixed up!
11:20 the reason you see a low voltage going to the starter is because the starter is in a locked rotor condition and draws excessive amps while NOT turning! Similar low voltage can be measured @ the Pos of the battery when the solenoid/relay is engaged !
Well, one thing I have learned from watching your videos is that I would never buy a non-running side by side. I don't think I have ever seen you get one that was simple to work on, and most have been a royal pain. My hat is off to you for your perseverance with these machines.
@JakeDemuss90210 Then where would he draw his content from. Why would we watch the videos if not to run through the whatever the problem with is to getting whatever he is fixing to a working state again. I feel that if you want it to be a problem then it is for you. If you enjoy the process of finding out the problem or problems and fixing them, then why would you, care about how the creator creates. I enjoy Joes videos. Therefore do not care about his endeavors, right or wrong. They are enjoyable to me.
No metal in oil because it set long enough they settled to the bottom.. been mechanic 40 years, stopped by a guys shop had one of those 275 gallon plastic almost see through totes that was full of oil.. asked him why it was outside.. it looked like clean new oil. He said it had been setting in sun for 10 years and all carbon separated and fell to bottom.. funny I had the same tote empty setting in texas sun 3 years later plastic just broke apart. Guess his oil kept plastic from drying out and breaking down? Love your videos keep them coming
Years ago, a bunch of us guys went to a Mud Bog event for the day. What happened that day pretty much sums-up this UTV. During one of the truck runs, this 'beasty' of a truck just stopped dead in the middle of the run. Everyone watching seemed perplexed at what had just happened. Someone in our group said, "Let's ask Clarence. He's smart and probably knows what went wrong." So we asked Clarence his opinion. Clarence said, "Something must have broke!"
greetings from Serbia, I follow every video of yours, all the best, and I do it myself, I would recommend you to pay more attention to cleaning and washing parts, meticulousness is 90% of the job
I have seen this on my dirt bikes one time and I would bet the factory left one of the piston's wrist pin snap-rings unsnapped. So after a while of running and vibration the piston pin drifted over to one side causing the piston to tilt just enough in thousands of an inch to cause it to stretch and hang on the cylinder's lower sleeve which then shredded the piston to pieces.
It can get worse, I had a Briggs and Stratton 8hp snow blower throw a rod through the cylinder block. Piston seized and the rod snapped. Great videos, keep them coming.
Wow Joe that thing is a showroom model, almost like a dealer sample.. so low miles and hours.. what a peach! Hopefully it's no biggie to get it running again the video is just a couple minutes in but man what a steal on it, even if you do need to do some engine work.. that's your thing!! Edit: Whoa!! That was TOTALLY UNEXPECTED OF A FIND!! Holy COW!!!
I took a boat to Jim & Seans Boat Repair (and pot dealers) in Spicewood many years ago and waited months for a new burned piston and head plaining. On one of many check-for-progress trips the 2 "mechanics" installed a V-8 head on a big block v-8 with a screwdriver in front cylinder, in front of me. I told them, but they thought I was giving them BS as payback for delays and continued the repair.... Wish I could have seen the start-up later.
Yes,but he always does the wrong steps first! You don't spend time testing solenoids and starters before pulling the plug! Or try starting, checking for spark, etc. before testing compression. He does this EVERY VIDEO.
Unfortunately, that's how the cookie crumbles at times. Love your videos and the detailed breakdowns, repairs as well as the assembly process. You motivated me to purchase a 2006 YZ450F for $800... lol. I have about $750 into it... waiting for the parts to arrive. Keep kicking ass man!
Just found this channel and this one blew my mind. Never seen anything like that. Since that spark plug was loose, I bet the guy you bought it from planned on fixing it, pulled that plug and put a scope down in the cylinder. Saw that disaster, put the plug back in and put it up for sale.
My brother was the auto mechanic, Cadillac, BMW, you name it, he could fix it even worked on diesel engines. However, me, I don’t know very little about the engine of a vehicle… however, even I know that a piston does not look like that, should not have been destroyed like that which is totally totally crazy. Now, 45 years ago, I did help a friend take apart his car and put new rings in it. And it was an activity that I actually enjoyed. I wished I had stuck with it, because, if nothing else I would’ve loved to of had the knowledge that you do. I can see where working on a vehicle of any kind can be habit for me.
We've done several of those, top ends mostly, few bad cranks, 29:10 not a fan. Cub Cadet are not the easiest parts to get. Great vid, just bad memories for me and my apprentice. 😮
Congrats @2vintage ! I can honestly say you have shown me one that ive never seen before. Not even in an automotive engine. Ive seen chunks missing and even holes in pistons but never the WHOLE DAYUM piston is gone and nothing but a wristpin sitting there.
OMG. I've pulled apart and rebuild a few engines in 50+ years but never seen one do that before. Just incredible. Good luck putting this back together again, although by the looks of the damage, a replacement engine might be a lot less hassle !
Great to see an honest teardown of engine that we unlucky mortals usually find ourselves working on (ie not one tweak and its working again)....reckon that engine was at full revs when that piston destructed,no old people riding that then.
Joe, thank you for the content, you do a wonderful job explaining and exploring all of these projects! I am very grateful you are here doing this 🙏 -Justin from New Hampshire
Love the channel, been following a LOT of re-builds. A little advice from an electronics engineer - Don't continually try to turn the motor over when the starter is locked up......you'll only end up burning out the starter and/or the solenoid. Also, a clue that either the battery is knackered or the starter was locked up was the backlighting on the clocks going dim when you turned the key.......a lot of current flowing out the battery and a large voltage drop.
Absolutely unbelievable!! Never seen anything like that! Looks like intentional sabotage or a prank! That gudgeon pin, that piston,, no way that would happen just by an engine seizure!! Look forward to seeing the rest of the repair!! Nice video!!
Great looking rig, now let's tear it apart! I Love Engine Out vids, but then I'm old. Again your patience and knowledge are amazing. You must have a better engine lying around. 400k Subs - BRAVO
Joe upon discovering @ 31:19 the piston had left the building, "What the heck" I feel at this point it's justifiably appropriate to say, WHAT THE FUCK!🤣 Apparently the grandkids were given the keys. 😂 After the many years of viewing this channel, this has got to be the finest episode that I have had the pleasure of consuming.🤣
My brother was the auto mechanic, Cadillac, BMW, you name it, he could fix it even worked on diesel engines. However, me, I don’t know what damn thing about the engine of a vehicle. Now, 45 years ago, I did help a friend take apart his brothers car and we put new head on it and replaced all the rings and, I can’t really remember what else we did but, it was fun. I enjoyed it, and I wished I had stuck with it, because, if nothing else I would’ve loved to of had the knowledge that you do. I can see where working on a vehicle of any kind can be habit for me.
Very clear example of corporate greed! placing extremely cheap and poorly designed engines and parts in $15,000 + UTVs. Another very good example why people should never pay close to MSRP for anything used and no warranty regardless of hours.
But,but,but, it looked like a great deal,for a while I was jealous of your lucky find,but honestly my heart goes to you. But still,slap in a rebuilt ,and their still good money to be made with it,and yes you are working for it. That is the joy and tribulations of the chase for a good deal. I'm following you on it,keep up bud.
My car ate a piston once. The valves jumped time by 3 notches. It accelerated like crap but got up to speed eventually. I was halfway home on an 80-mile trip when the #2 piston disintegrated. Scarred the cylinder wall a bit. I replaced it with a junkyard piston and got another 8 months out of it before it went again. That time it took out the cylinder wall. I replaced the engine at right around 100,000 with an engine that had about 120,000 on it. That went another 45,000 miles before it developed a knock. Once I tore it down, I figured out it was the flex plate rattling on the torque converter. My pistons were completely sludged up though, and the oil pump needed a new seal. About $800 later it's all back together and running like new or better. Yes, the rod bearings will be fine, but the cylinder wall will be toast. You may have gotten lucky on the valves (I'm at 37:16 in).
Pardner these machines that just quit running you need to start doing a bore scoping and quit taking the sellers word. If they refuse to let you then just walk away. Love you videos. Done this my whole life buy fix and sell. Lot of good people out there but a lot of bad ones also.😊😊😊😊😊
the worst engine damage i ever saw was a 05 troy lee predator i bought for parts when i was young.. younger kid was riding went from 5th to first blew the piston off the wirst pin broke the rod and the rod acted like a saw at 10000 rpm or more about slicing the motor in half cut the entire front corner off the motor off cut the starter in half cut the input for the trans in half blowing gears through the clutch side center case and the clutch basket blew through the cover the piston hit the head so hard it broke the timing chain and bent the exhaust and push the head up about an 1inch high off what was left of the cylinder... i was amazed the kid got off the machine without even a cut there was bent and dented parts of the frame around the motor where parts hit it and a trans gear lodged in the bottom of the seat pan... i wish i still had the pics of it it was just amazing
I absolutely DESPISE when I see people connect a TONE of crap to the battery. Get a junction box and put it to the side and run a cable down to it. You can properly fuse it AND it looks neat. I just dont get why people insist on doing it this way.
Looks like someone lefted a few things out when telling you about that engine. You could always run it Freddy Flintstone style in the meantime. Well the good news is it can be fixed with time and bit of money but you can get it done... You sure do find you some good one's...
I haven’t heard very many people boasting on Cub Cadet products, quite the opposite in fact. After watching this nightmare, I don’t see myself ever buying anything sold under that brand.
Joe, I had a Suzuki dealership with my dad in the 70's we replaced rods ourselves using the shop press to press apart installing new rod and bearing and pressing back together then using a straight edge making the counter weights even never had a problem u might try it. We did it on all the racing bikes as well.
When you pulled the head off and there was no piston I cried with laughter and nearly fell off my armchair. How is that even possible. Might pay to look for an engine.
Made in China with junk Chinese parts is the problem. They have these China made piles of junk sitting in the entry ways of Fleet Farms, Menards, Home Depot all over the country. All you have to do is look at em, a child of 4 can see they are junk scrap heaps. If yer still not convinced, then test drive one, then run away as fast as you can. banks won't give you loans on these crap heaps.@@craigeldridge2695
9 месяцев назад
Gotta love it....another example of people who get in...turn the key....drive around...park it, then do the same routine over and over. Dont bother with maintenance...it only keeps them running.
I'm 70 and have been a mechanic most of my life I NEVER thought the piston would be gone hahahaha I bet the guy just tried to start the motor over and over again forget the knocking sounds until the piston stuck under the crank ,
Could be. But with the information given in the video we know that that the average speed of this machine was no more than 8 mph (1664 miles divided by 201 hrs), this math doesn’t account for idle time either so I would expect it to be less.
That's funny you say that. Cause I thought the same thing. Cause when he took off the first valve cover it was missing a bolt. So someone was definitely in there for sure. But yeah when he said the piston was gone I said someone definitely took it apart and put it back together hahahaha
Cub Cadet is One of the 8 brand names out there made at the Chinese company of Hysun (spelling) I forgot all there names now, but back in 2020 we bought a brand new Massimo and had it shipped to out door in Floo’da from Texas for $5,900 …!!
Bro a perfect use for this things is to pull the old engine and add a 600/ 1000cc sport bike engine that would be 10x more badass then any modern utv@@nebs888
I believe the term "GRENADE" would best describe the crankcase here ! I blew up a 327 Chevy engine when I was 16. I missed 2nd. gear, and the ABRUPT SOUND of Silence after the LOUDEST BANG is hard to describe... I had a 3 mile walk home to think about it though. And YES, the bottom end looked very similar to this engine. ☹😥😱
He went from maybe it's just a loose battery cable, that would be amazing to, what the heck, the piston is missing. 😅😅 Never changed his tone, didn't lose it his 💩 This guy is awesome
No swearing or cussing, no annoying background music, so I subscribed
It has been 5 months. Did you part it out? Buy another Chinese Hisun engine? or decided it wasn't worth anymore of your time? click a thumbs up if you want a followup also.
I’ve seen a lot of engine tear downs in my lifetime, but nothing ever like this. You couldn’t do that to the piston with a blow torch and hammer. Truly amazing.
Lol,,,, That is a bad one,,,, whew
Hmmmm, you have a battery that needs a charge or is possibly bad so you jump right to pulling the starter??? Then you pull a spark plug (still don't have enough voltage to even run the starter but you pull it just the same) plug is bent. Nothing in an engine will bend a plug like that so maybe when they were checking a no start engine they dropped the plug. However even though you still don't have enough power to start you go ahead and break down the engine. Noti g that the valves are fine no bad wear and tear on anything ahah! Piston is missing !!! Even though you had no reason to expect anything other than a dead battery (you need to show 13.5 volts at rhe battery to be good) so even though the oil is clean with no visible degree, no sign of heat distortion or virtually anything that would be indicative of a thrown rod or failed piston, cracked rings or anything . . . . You go straight to a tear down. . . . Some people will do anything for content. Small people with nothing real to offer.
@@zorrorides1 ur a 🤡
@@zorrorides1 I gave up on this video after 13mins when he couldnt even use a multimeter properly and then thinks there is a drain in the system cos his charger chows 12.1v and battery shows 11.8v.
@@zorrorides1 'you need to show 13.5 volts at rhe battery to be good' Nope. The voltage of a car battery should be around 12.6 volts when fully charged and the engine is off. Between 13.7 and 14.7 volts with the engine running.
I am a retired internal combustion maintenance and repairs engineer and in my opinion that engine was held flat out in neutral till it destroyed its self. That’s after its original partial seizure. I love watching your videos and hope you have a very successful life.
Regards
Raymond 🏴
" I am a retired internal combustion maintenance and repairs engineer " Wow, thats a mouth full for a made up title. Typically Engineer designs things, not fixes them.
All true my friend. It’s not made up I can assure you
So a retired mechanic then @@raymondrobertson3869
The clue is in the title on my apprenticeship papers. I will give you a clue 🤔maintenance. Not design. I have overhauled many many engines in my younger days
And could still do it today. As long as someone did the heavy lifting 😂🏴👍👍
@@ugetridofitAka he's a mechanic.
I've watched you work through a lot of simple fixes, but this is a good reminder to people that when you shop on craigslist, you never know exactly what you're getting. Most people would be at a total loss to fix this repair, my hat is off to you. 👏 EDIT: yeah, that piston will be fine, use some J-B Weld...LOL
@2vintage looks like Cub has a lot of parts available, you might make out ok. looks like the piston is about $200, and the entire cylinder head assembly is about $1k.
That is a Hisun engine, just rebranded for Cub. Motorcycle Doctor out of Missouri is a good source for parts and knowledge on these.
Poosun
idk about it being a pile of poo .. my hisun 450 sector hasnt let me down .. ive jumped it countless times ,starts up in - temps and kicks ass for plowing the driveway and plow contracts at malls that i have @@catsbyondrepair
@@catsbyondrepair lol
And this is why I love RUclips and its crowd sourcing. Great info!!
are they cast pistons? thats the only way i see this happening. there has to be others with the same problem. Edit, yes they are cast aluminum pistons. im surprised this isnt a more common issue on china motors.
yeah, right... Lil old couple just drove it to church on Sunday. WOW, never say that happen in all my years... Good luck. I hope you can fix it. This is a really interesting one.
I'd also like to congratulate you Joe on the 400,000k subscriber level you've reached,People obviously appreciate what you do as much as me,Onwards to half million 🤙
Perfect number to find a piston missing 😅😅
Sounds like you aren't going to need a w/s wiper for a while!!!
My father was a JD diesel mechanic his entire career… as with you he had a brilliant mechanical mind. I did receive that gene but your mechanical hunting skills are like his were…you folks are amazing
If you own a small wire feed welder here's a small tip......Don't struggle with the pain and aggravation of pulling and installing the engine. Put a .065 cut off wheel in your angle grinder and surgically remove the obstruction and weld the piece back in upon reassembly....I did this multiple times on Ford Econoline Vans 30 years ago.
Brilliant!
Oh my god, that is hilarious! In my 45 years as a professional tech, I have never seen that level of crazy. Let me guess, the owner never heard a thing.
Why is that funny
@@MidnightPolaris800 ?
@@MidnightPolaris800 ?
Tech: Did you hear anything weird when it stopped? Customer: Hear What I am half deaf, and it always makes this funny little noise, crash, bang, scrape, swish, crunch. As the head is eating the piston! lol I bet this guy never changed or checked any of the fluids on the thing since he bought it.
@@tracysellman1562 Im going to bet he didnt know it took anything else than gas, hahaha
I’d definitely try and find a complete used engine for it and skip the rebuild if possible. Good luck!
I'd slap a small block chevy in that bad boy! 🤣😂🤣
Exactly. A full rebuild would be a good investment.
And start again with someone elses problem, no rebuild what you have as you know the problem
@@anthonymisell8845 i agree, rebuild this engine, he now knows what he is dealing with. another engine is begging for more work, nope, i'd rebuild this engine with all new/used parts.
Yea, I agree
Just bought a non running Royal Enfield Himalayan and when I took the head off it was the same situation. The piston had blown apart. Everything was unusable, head, cylinder, crank. I opted for a replacement engine as even the cases were banged up, plus the replacement engine was cheaper than a rebuild. Good luck!
What did a new motor cost you?
@@glengarbera7367it was around a grand with shipping for a basically brand new (2 miles) engine.
@@pjm204 lol. My old girlfriend sold motorcycles at a dealer In Toronto. You would be surprised how many folks write off bikes within minutes of leaving a dealership.
I had a VW as a first car. Overall a good car but started loosing pressure. Took it to a mechanic to get it fixed. It ran really smooth until the intake valve got sucked into the piston (read through) when I was getting on the Freeway 2 blocks from my house. That thing sounded like a thrashing machine on a bad day. But the mechanic was honest and rebuilt it for free. He had misread his calipers. Owning up to a mistake brought greater respect.
i just found this video tonight and i was fully immersed in it. I look at your channel and i see no follow up video. bruh..it's been 4 months....bruh...i'm freakin' out ova here!
I don't understand why he never power washes anything before he takes it apart. The least he could do is blow some of the dirt off with air.
I took my first head off a briggs and Stratton in 1967 . I've done a thousand since then. And I never saw a crankshaft devour a piston like that. Awesome ❤. Always entertaining. Still worth 3500. The vinster can't even look at this catastrophic mess. Lol 😂. ❤❤❤
That is really unbelievable! Can't say I've ever heard of an engine digesting a piston. 🤣 Please keep the content coming! I have to say that even though I don't ride a motorcycle, ATV or UTV, I have really learned a lot about small engines from watching you patiently and methodically tackle each project. I have to also admire your mid-western good manners and patience having never heard a swear word on your channel. If it was me, you would have only heard minutes of bleeps during the inevitable setbacks. Great job!
Bro, Amazon has many MANY cheep boroscopes you plug into your phone, i got one for $20 with a light up end and it works awesome..... You should get one buddy.....makes life so much easier.👍👍
It amazes me how you can take everything apart and remember how to put it back together!
He has everything on Video, the perfect memory!
The idea is to watch and remember how it comes apart silly
I just wing it. I end up with some spare bolts at the end but I just put them in a jar in case I need one later on. 😀😆🤣
Iv niver seen anything like that in my life and I'm a machanic retired. the person who sold you that knew.he has Put a scope in the plug hole and seen there was no piston. Good luck buddy you will still come out on top.
I was wondering why he did not do a compression test and squirt some oil down the plug hole like he usually does. On the whole he is very good with carbs and trouble shooting. Do the testing first. A bore scope would have said a lot.
Of all the things you have fixed this is the craziest! That thing had to be knocking terrible until it let go.
nope
The ole disappearing piston trick. I've seen a lot of engine carnage, but never that. Usually when a piston lets loose like that there would be holes in the case. That's impressive!
Exactly...
Old folks probably didnt check the oil like they should.
Joe needs a bore scope.
So is he a sucker ?
Must have been a chinese piston of dubious quality.
first for me too, never seen anything like that before. musta disintegrated and not turned any further to spread chunks.
seen a BSA twin with a wooden piston sold as not running very well
I used to work for MTD (Cub Cadet) and had this exact unit as a demo to engage dealerships to sell these machines. Hisun is the manufacture. Lots of issues with the wiring harnesses and lack of manufacture support, forced Cub to pull the plug on the Challenger 750 efi. I never had an issue with my demo and loved it. Hope you get it fixed up!
Never give up. You just dont quit. This is a real mechanic.
11:20 the reason you see a low voltage going to the starter is because the starter is in a locked rotor condition and draws excessive amps while NOT turning! Similar low voltage can be measured @ the Pos of the battery when the solenoid/relay is engaged !
Stopped in water crossing!
I was starting to think somebody removed the piston, then put the whole thing back together 😄
Me too 😂
Same
That would’ve been a real who to whot
I was thinking the same, but the manner in which the bolts came out and other key tells kept popping up I was like, "Wtf is going on here?"
Or somebody needed just one piston, real bad.
Well, one thing I have learned from watching your videos is that I would never buy a non-running side by side. I don't think I have ever seen you get one that was simple to work on, and most have been a royal pain. My hat is off to you for your perseverance with these machines.
I don’t think that is a problem, I would guess that it is intended that way. He is after all a small engine repair wizard.
@JakeDemuss90210 -- How many subscribers do you have on *your* channel? Yup -- that's what I thought. :(
@JakeDemuss90210 Then where would he draw his content from. Why would we watch the videos if not to run through the whatever the problem with is to getting whatever he is fixing to a working state again. I feel that if you want it to be a problem then it is for you. If you enjoy the process of finding out the problem or problems and fixing them, then why would you, care about how the creator creates. I enjoy Joes videos. Therefore do not care about his endeavors, right or wrong. They are enjoyable to me.
@JakeDemuss90210 I like his vids, if you don't then why not go somewhere else and watch their vids instead of complaining.
I am by no means a mechanic but your video was outstanding. Now i know why I am willing to pay someone with experience to fix my stuff. Well done.
No metal in oil because it set long enough they settled to the bottom.. been mechanic 40 years, stopped by a guys shop had one of those 275 gallon plastic almost see through totes that was full of oil.. asked him why it was outside.. it looked like clean new oil. He said it had been setting in sun for 10 years and all carbon separated and fell to bottom.. funny I had the same tote empty setting in texas sun 3 years later plastic just broke apart. Guess his oil kept plastic from drying out and breaking down? Love your videos keep them coming
First time i have ever involuntarily let out a "wtf" while watching Joe.
That was a surprise to me.
Years ago, a bunch of us guys went to a Mud Bog event for the day. What happened that day pretty much sums-up this UTV. During one of the truck runs, this 'beasty' of a truck just stopped dead in the middle of the run. Everyone watching seemed perplexed at what had just happened. Someone in our group said, "Let's ask Clarence. He's smart and probably knows what went wrong." So we asked Clarence his opinion. Clarence said, "Something must have broke!"
No shit sherlock!!
A friend in telco always said, “somethin come a loose!”
greetings from Serbia, I follow every video of yours, all the best, and I do it myself, I would recommend you to pay more attention to cleaning and washing parts, meticulousness is 90% of the job
You're absolutely right!
I have seen this on my dirt bikes one time and I would bet the factory left one of the piston's wrist pin snap-rings unsnapped. So after a while of running and vibration the piston pin drifted over to one side causing the piston to tilt just enough in thousands of an inch to cause it to stretch and hang on the cylinder's lower sleeve which then shredded the piston to pieces.
It can get worse, I had a Briggs and Stratton 8hp snow blower throw a rod through the cylinder block. Piston seized and the rod snapped. Great videos, keep them coming.
Wow Joe that thing is a showroom model, almost like a dealer sample.. so low miles and hours.. what a peach! Hopefully it's no biggie to get it running again the video is just a couple minutes in but man what a steal on it, even if you do need to do some engine work.. that's your thing!!
Edit: Whoa!! That was TOTALLY UNEXPECTED OF A FIND!! Holy COW!!!
A perfect video to start you on your way to 500k! Thanks for letting me come along for the ride.
I've always wanted a utv but all the plastic parts and problems I've seen on your channel has changed my mind I'll just keep using my trx 😮
If you can find a low mile bike built before the 2000s that will be the best bike ever all this newer stuff is garbage.
The good news is that the same engine is used in quite a few SxS from HiSun, Odes, Massimo, etc, so you should be able to put something back in there
I took a boat to Jim & Seans Boat Repair (and pot dealers) in Spicewood many years ago and waited months for a new burned piston and head plaining. On one of many check-for-progress trips the 2 "mechanics" installed a V-8 head on a big block v-8 with a screwdriver in front cylinder, in front of me. I told them, but they thought I was giving them BS as payback for delays and continued the repair.... Wish I could have seen the start-up later.
I love how you do one step at a time to find out what is wrong. Then you fix it!
Yes,but he always does the wrong steps first! You don't spend time testing solenoids and starters before pulling the plug! Or try starting, checking for spark, etc. before testing compression. He does this EVERY VIDEO.
Spark plugs and compression should be checked BEFORE any thing is bought! @@Mizman76
Unfortunately, that's how the cookie crumbles at times. Love your videos and the detailed breakdowns, repairs as well as the assembly process. You motivated me to purchase a 2006 YZ450F for $800... lol. I have about $750 into it... waiting for the parts to arrive. Keep kicking ass man!
amen! lol
Congrats on 400k Joe!!!
Just found this channel and this one blew my mind. Never seen anything like that. Since that spark plug was loose, I bet the guy you bought it from planned on fixing it, pulled that plug and put a scope down in the cylinder. Saw that disaster, put the plug back in and put it up for sale.
My brother was the auto mechanic, Cadillac, BMW, you name it, he could fix it even worked on diesel engines. However, me, I don’t know very little about the engine of a vehicle… however, even I know that a piston does not look like that, should not have been destroyed like that which is totally totally crazy. Now, 45 years ago, I did help a friend take apart his car and put new rings in it. And it was an activity that I actually enjoyed. I wished I had stuck with it, because, if nothing else I would’ve loved to of had the knowledge that you do. I can see where working on a vehicle of any kind can be habit for me.
See that green base gasket it's been replaced so at one point and time someone had that engine apart
Yep, they pulled it apart, took the piston pieces out and bolted it back together.
@@djpar3492They also drained the oil, and put cleaner used oil back in...then listed it!🙄
Surprised they didn't try to recap the plug too
We've done several of those, top ends mostly, few bad cranks, 29:10 not a fan. Cub Cadet are not the easiest parts to get. Great vid, just bad memories for me and my apprentice. 😮
Congrats @2vintage ! I can honestly say you have shown me one that ive never seen before. Not even in an automotive engine. Ive seen chunks missing and even holes in pistons but never the WHOLE DAYUM piston is gone and nothing but a wristpin sitting there.
OMG. I've pulled apart and rebuild a few engines in 50+ years but never seen one do that before. Just incredible. Good luck putting this back together again, although by the looks of the damage, a replacement engine might be a lot less hassle !
Great to see an honest teardown of engine that we unlucky mortals usually find ourselves working on (ie not one tweak and its working again)....reckon that engine was at full revs when that piston destructed,no old people riding that then.
Joe, thank you for the content, you do a wonderful job explaining and exploring all of these projects! I am very grateful you are here doing this 🙏 -Justin from New Hampshire
Love the channel, been following a LOT of re-builds.
A little advice from an electronics engineer - Don't continually try to turn the motor over when the starter is locked up......you'll only end up burning out the starter and/or the solenoid.
Also, a clue that either the battery is knackered or the starter was locked up was the backlighting on the clocks going dim when you turned the key.......a lot of current flowing out the battery and a large voltage drop.
starters and solenoids are cheap though so its not a big deal at all.
Absolutely unbelievable!! Never seen anything like that! Looks like intentional sabotage or a prank! That gudgeon pin, that piston,, no way that would happen just by an engine seizure!! Look forward to seeing the rest of the repair!! Nice video!!
Love that cheater bar! I am Enjoying watching you take apart the engine, and how you tested the parts. ❤❤
Great looking rig, now let's tear it apart! I Love Engine Out vids, but then I'm old. Again your patience and knowledge are amazing. You must have a better engine lying around. 400k Subs - BRAVO
Previous owner;
"Older couple, lived on farm, low miles, low hours, driven on Sundays, quit while driving with no warning"
Suuuuuuuure.
lol
With ORV sticker on it. Grandma likes to dive on the sand dunes, but she never beat on it.
Holy crap buddy! I'm 61 years old and I've seen everything but I've never seen a piston completely disintegrated. Wow
You've never seen a piston or rod get thrown? Must not deal with engines much, I had seen multiple before I was 18.
What's the status on this? Any updates? Will there be a part 2? Please like this comment so we get a follow-up
Wondering the same
@@huntsonoraI’m wondering the same thing
Sell it for scrap 😂
Was just coming to comment this!!!!!
This just popped up again. I’m assuming it went down the road?
Taking that hose off unlocked a hidden achievement based on the sound that came as soon as it detached :D
Love the videos!
Congratulations on 400k subscribers!!!!
It's probably something easy!
Geez, they got the mix off when casting that piston.
I always avoid vehicles driven by someones grandparents.
Joe upon discovering @ 31:19 the piston had left the building, "What the heck" I feel at this point it's justifiably appropriate to say, WHAT THE FUCK!🤣
Apparently the grandkids were given the keys. 😂 After the many years of viewing this channel, this has got to be the finest episode that I have had the pleasure of consuming.🤣
My brother was the auto mechanic, Cadillac, BMW, you name it, he could fix it even worked on diesel engines. However, me, I don’t know what damn thing about the engine of a vehicle. Now, 45 years ago, I did help a friend take apart his brothers car and we put new head on it and replaced all the rings and, I can’t really remember what else we did but, it was fun. I enjoyed it, and I wished I had stuck with it, because, if nothing else I would’ve loved to of had the knowledge that you do. I can see where working on a vehicle of any kind can be habit for me.
Very clear example of corporate greed! placing extremely cheap and poorly designed engines and parts in $15,000 + UTVs. Another very good example why people should never pay close to MSRP for anything used and no warranty regardless of hours.
I can’t wait to watch the outcome of this. I hope you are able to finish this project and take some serious hot laps. 😊
Ive been looking for a couple of yrs and this is my first time seeing so much carnage like this.
Wow Best video Yet, Holy Cow! Never seen that before either.
But,but,but, it looked like a great deal,for a while I was jealous of your lucky find,but honestly my heart goes to you.
But still,slap in a rebuilt ,and their still good money to be made with it,and yes you are working for it.
That is the joy and tribulations of the chase for a good deal.
I'm following you on it,keep up bud.
My car ate a piston once. The valves jumped time by 3 notches. It accelerated like crap but got up to speed eventually. I was halfway home on an 80-mile trip when the #2 piston disintegrated. Scarred the cylinder wall a bit. I replaced it with a junkyard piston and got another 8 months out of it before it went again. That time it took out the cylinder wall. I replaced the engine at right around 100,000 with an engine that had about 120,000 on it. That went another 45,000 miles before it developed a knock. Once I tore it down, I figured out it was the flex plate rattling on the torque converter. My pistons were completely sludged up though, and the oil pump needed a new seal. About $800 later it's all back together and running like new or better.
Yes, the rod bearings will be fine, but the cylinder wall will be toast. You may have gotten lucky on the valves (I'm at 37:16 in).
Thats crazy. Ive seen dropped skirts and cracked pistons but thats just insane.
Chinese engineering.
Little rip..half the damn seat is gone😂
My thoughts exactly, sounds like a bunch of grandkids.
Keep on brother, love the content!
You should show more of this. It is awesome to see people helping people like this.
Pardner these machines that just quit running you need to start doing a bore scoping and quit taking the sellers word. If they refuse to let you then just walk away. Love you videos. Done this my whole life buy fix and sell. Lot of good people out there but a lot of bad ones also.😊😊😊😊😊
Define “Older Couple” that thing was rode hard and put away wet!
It was rode hard and put away DEAD!
But they only used it for gardening and church on Sunday. HONESTLY 😵💫
this is now my favorite small engine repair channel!
''a episode'' from ''I do cars''?
the worst engine damage i ever saw was a 05 troy lee predator i bought for parts when i was young.. younger kid was riding went from 5th to first blew the piston off the wirst pin broke the rod and the rod acted like a saw at 10000 rpm or more about slicing the motor in half cut the entire front corner off the motor off cut the starter in half cut the input for the trans in half blowing gears through the clutch side center case and the clutch basket blew through the cover the piston hit the head so hard it broke the timing chain and bent the exhaust and push the head up about an 1inch high off what was left of the cylinder... i was amazed the kid got off the machine without even a cut there was bent and dented parts of the frame around the motor where parts hit it and a trans gear lodged in the bottom of the seat pan... i wish i still had the pics of it it was just amazing
I don't think I've ever seen a sentence this long😮
@@azopene thats whats she said
@@azopeneIt's all about firsts on Joe's channel! 😂😂
Incredible viewing. You definitely have a huge amount of perseverance and patience. I take my hat off to you.😊
I absolutely DESPISE when I see people connect a TONE of crap to the battery. Get a junction box and put it to the side and run a cable down to it. You can properly fuse it AND it looks neat. I just dont get why people insist on doing it this way.
I've seen alot of crazy stuff while fixing bikes and quads but no piston and then to find it in the bottom end that has to be a first.
Looks like someone lefted a few things out when telling you about that engine. You could always run it Freddy Flintstone style in the meantime. Well the good news is it can be fixed with time and bit of money but you can get it done... You sure do find you some good one's...
lol! Freddy style!
WILMAA...!! 😂😂
I haven’t heard very many people boasting on Cub Cadet products, quite the opposite in fact. After watching this nightmare, I don’t see myself ever buying anything sold under that brand.
Are they an American made machine?
The new cub cadets suck. The good ones are the old OG ih cub cadets. I'd never own any new "cub cadet" product
Designed and engineered by Cub Cadet, the Challenger series is manufactured by Hisun Motors Corp. at its factory in Chongqing, China.
It appears to be the same engine as the yamaha 660 those aren’t really known to be the most reliable but i’ve never seen one do this😅
Joe, I had a Suzuki dealership with my dad in the 70's we replaced rods ourselves using the shop press to press apart installing new rod and bearing and pressing back together then using a straight edge making the counter weights even never had a problem u might try it. We did it on all the racing bikes as well.
This is the best side by side troubleshooting video I've ever seen.
When you pulled the head off and there was no piston I cried with laughter and nearly fell off my armchair. How is that even possible. Might pay to look for an engine.
Right? I was like, why are we seeing a wrist pin?!
Your "armchair" who the hell calls a chair an armchair😂
@@MidnightPolaris800An armchair mechanic of course! 😂😂😂
Your new theme song lately. "I'd catch a grenade for ya" 😂
Yeah these were a bad design. Lot of complaints bout the piston grenading. Weak oil pumps burn up then 💥
Cub Cadets were owned by International Harvester until 1980. Sold to MTD, there's your problem.
Made in China with junk Chinese parts is the problem. They have these China made piles of junk sitting in the entry ways of Fleet Farms, Menards, Home Depot all over the country. All you have to do is look at em, a child of 4 can see they are junk scrap heaps. If yer still not convinced, then test drive one, then run away as fast as you can. banks won't give you loans on these crap heaps.@@craigeldridge2695
Gotta love it....another example of people who get in...turn the key....drive around...park it, then do the same routine over and over. Dont bother with maintenance...it only keeps them running.
I'm 70 and have been a mechanic most of my life I NEVER thought the piston would be gone hahahaha I bet the guy just tried to start the motor over and over again forget the knocking sounds until the piston stuck under the crank ,
I don't think the older couple blew this up. This was ridden hard imo
Exactly. By the looks of all that caked mud under the engine bay my guess would be that the grandkids blew that thing up.
Could be. But with the information given in the video we know that that the average speed of this machine was no more than 8 mph (1664 miles divided by 201 hrs), this math doesn’t account for idle time either so I would expect it to be less.
That's funny you say that. Cause I thought the same thing. Cause when he took off the first valve cover it was missing a bolt. So someone was definitely in there for sure. But yeah when he said the piston was gone I said someone definitely took it apart and put it back together hahahaha
"the older couple". Haha..... Fiction
@@dezrtrat702 if you deduct the idle time (0 mph) wouldn't it make the average speed higher?
Looks like a piston circlip came out,&the gudgeon pin moved smashing the barrel lining& the piston exploded.
Wrist pin: don’t look at me.
That’s a first ! The crap they build these days. Stay to the vintage Jo you learnt your lesson
Cub Cadet is One of the 8 brand names out there made at the Chinese company of Hysun (spelling) I forgot all there names now, but back in 2020 we bought a brand new Massimo and had it shipped to out door in Floo’da from Texas for $5,900 …!!
Your my new hero buddy. I can't believe the piston was just gone!!! Grandkids must have taken an easy ride behind grandparents eyes lol.
More like old couple bought it grand kids beat the hell out of it old couple got rid of it that's probably the real deal
Maybe, but we don't know this for a fact.
Any update on this machine?
Same, I'm kinda curious🤷♂️
Wasted..
Bro a perfect use for this things is to pull the old engine and add a 600/ 1000cc sport bike engine that would be 10x more badass then any modern utv@@nebs888
Is there a second part to this?
Also waiting on 2nd part!
I believe the term "GRENADE" would best describe the crankcase here !
I blew up a 327 Chevy engine when I was 16. I missed 2nd. gear, and the ABRUPT SOUND of Silence after the LOUDEST BANG is hard to describe...
I had a 3 mile walk home to think about it though. And YES, the bottom end looked very similar to this engine. ☹😥😱
As a native Michigander I agree with you that GR is pretty special. I was born and raised in Montcalm County.
Hisun=Nofun. What a mess. If I were you, I'd never buy another side by side again. Congrats on 400K subs though!
It's the age old story: A little old lady only drove it to church on Sundays.