Видео

one of the best tutorials there is , i managed to do it first try, i followed every single step you make in the video.

what is the difference between v2 and v3 flex? cai i use de v2 flex on the oled switch?

Hey buddy, can you check on my order 11190. Sent it over a week ago. Cant wait!

Where’s your shop located?

What is your iron temp?

Hi, thank you for this tutorial! Where i can find that dat0

Can you explain the software part to finish the work? Thank you!

In my first installation the most difficult for me was the point in the 3.3 v to solder the resistor, in my second lite, the points where the cpu is was difficult because the flex cable was too open

The CPU soldering technique looks to be more efficient and with less hassle than other peoples video, very impressive. I will be trying to do a V2 installation soon and will be trying to do the way that you do (without pre-tinning the flex). Videos that tin the flex always seem to have problems with attaching the cable (have to do multiple times).

@10:55 you dropped some solder on the bottom of that 3.3v connection at the top of the ribbon cable real quick but you didn't say anything and when I pause it, it looks like there are connections at the top and bottom but you just did a real quick job on the bottom connection but not the top? @ 12:05 you show a really good pic of it but the top is not soldered? Does that 3.3v not need to be connected at both ends? It also looks like you're supposed to jump the two together on the top and bottom? What's going on there? Seems kinda important.

Hi, I have question a Nintendo switch switch came in for repair I change the usb port and P13 chip as it had shots. Now switch is fix working and charging fine. But the problem is it is not docking. I have checked LCD connector it is fine as well and there is no shot around M92 chip as well. But still not image on TV. What could the problem and advice

What is the temperature that should be set to remove capacitors?

Don't you have to clean the flux?

Soldering is one thing but when you require a microscope...at one point its just cheaper to get someone to do it instead of buying all the equipment.

nice clear thermal paste mate lol

I followed your video step by step, I like how you go into detail about everything, my issue is my oled will not boot with the picofly install, however if i remove the ribbon cables from the picofly it boots up like nothing ever happened, any advice? or tips? Thank you for your time

My switch lite has a purple screen after installing RP2040, any idea what could be the problem?

So I attempted this myself, though I did ok, had all the right readings. Got the firmware flashed and it won't boot. It gives me one solid blue light, then yellow x2 a pause yellow x2, pause yellow x2 and then nothing. What could I have possible messed up? 🤦‍♂️

Que estaño y flux utilizas ? me acabo de incursionar en este mundo . Me compré una baku 909, esta muy buena la maquina pero el estaño y el flux no me acompaña . Soy un seguidor nuevo me estoy viendo todos tus videos, eres muy bueno. 😄

Maestrazo. He estado practicando mucho últimamente con kits SMD, y creo que por fin me voy a animar a hacer este mod

So anyone knows how the bios chip gets corrupted in the first place?

Which microscope did you recommended me to get one? Thanks in advance.

Just finally got around to installing the older ribbon version I've had for months yesterday on my lite and this would have been so much nicer to have. Also, my picofly board was dead but not by me, touched up the solder joints around the RP2040 chip and it works great now.

The chips also need to be flashed with software first. People never mention this.

16:20 I tend to find many that botched this part up. The unintended pads are too close to the other capacitors (the right side ones), you came close to shorting the right side too! Trying to get out of it is HARD with cheap irons and most often than not they will lose the capacitor trying to fix it. What I usually find out is their soldering tip is not small enough nor hot enough if its too small. I've tested a few methods to counter this for "everyday joes" to do it with their normal irons and the BEST way is to put a tiny layer of solder mask on the unintended caps. It will save their bacon, perhaps you could do it in a video.

👍😸

so fast and efficient + explaining what is going on without skipping a beat.. Masterclass at work :) keep it up !

how and why the solder is so well connected and brillant on the iron ? what is your solder wire and your temperature :) ?

order mine going to do it friday i do have all the tools to do it just nervous on fucking it up lol

If i install a digital edition bios will it still work on a disc editon to convert to digital only?

Hi, I am considering sending my switch to get a mod chip installed through your company. Though after looking at Wayayeo's Service and its contreversial reviews on Yelp, It's kinda making me reconsider the decision, is everything fine? ☹️ I can't find anyone to solder and this was one of my options.

Which one is better? The new one or the old type?

Which Temperatur is recommended?

I can also confirm that he is 100% legit Responded to every call every text he is super professional He knows what he is doing and i would recommend him to everybody wanting any repairs at all i shipped him my switch oled all the way from the bay area Everything came back working as it should and super clean work i couldnt be happier wish this guy the absolute best and i hope your business booms not too many honest and trustworthy men like yourself!!!! ( ALSO HE TOOK 2 DAYS!!! )

What iron temp? Nice work.

He visto trabajos chambones y este

Sería buneo que explicases exactamente que materiales usaste y no nada más directo vayas a la parte de soldar

Hola qué tipo de herramienta usas para cortar las láminas me podrás pasar el modelo de las pinzas gracias

Any reason you use different wires. From the enameled copper wire to the insulated yellow wire?

What size wire are you using? Nice work.

i am having an issue where it doesn't boot the lights come on but it is one blue followed by 6 yellow lights. Has anybody had this issue before?

hola con que cortas el aluminio si no es con el drimer ?

Are you plugging it in via usb-c at the very end to get it to initiate the glitching?

Man i couldnt even attempt to micro solder...And then not even do the job correctly. And now send it to get it repaired Should of just send it the first time to get the job done correctly!

Great guide and soldering skills but my god, why reuse the same, old thermal paste? 😮

I hate to be that person, but what are you installing on the board? I’m pretty sure it’s some kind of bypass or a common issue on these Oled’s, but I haven’t worked on any thus far, but would love to know what issues this resolves with them Thank you

You are so bad man 🤦‍♂️

Amazing job. What is the millimiter of the wire you used?

So where do we find what to do after the chip is installed . Like the process after that with the sd card. ??

so crazy how people attempt this install and have gorilla hands. Look at all the scratches near cpu traces where you cut the metal shield out lol