Видео

I did a 52 V battery upgrade. I talked to one of the vendors and they said to set my P6 to 17 or 18 but that wasn’t enough. I found that 21 was perfect for P6 for my battery. I used this chart I found on 52v battery voltage to help guide . When my battery is at 50.4 V, then that is 50%.

fenders where do you get them?

Adding power is great...but How are the stock rad axel torque plates holding up? Id really hate to have the axel slip and rip out the motor wires. Has anyone had any issues and has anyone, installed any kind of upgrade? Thanks

Thanks I've probably referred to this a dozen times.

I have been searching high and low for someone to explain C-1 and finally, I found it I have been setting this wrong I guess and now I hear if you have 12 magnets set to 3 thank you I will change this setting later today and hopefully I will get the correct reading in my display thank you sir

Why are there 2 different versions of this display I have the same version as you,but I've seen the same display with a different screen

Best thank YOU 😊

Anyone know how to adjust the walk mode speed? My walk mode seems to have too much power when I use walk mode....please help to tune down???

Fuck yea man your the greatest my bike refused to display any speed and this video helped so much thank youuuuuu 🔥🔥🔥🔥🔥

since the password is 3 digits it can be brute forced in 1000 tries if it is numbers. if it is letters then 17576 tries because 26x26x26

Was that all on battery only or pedal assist

Does anyone have a screenshot to share or setting outline for RadRover 6+ with the 35A Controller. Much appreciated.

All you have to do is grind 1/16th of an inch between a tooth in the first gear ring and you can fit the security bit perfectly to take those 6 screws out.

Thank you!! Super helpful!!!!

Does this work with the RadRunner 3?

My bike wasn’t doing over 10mph I tried ur setting and it went up to 14.1 I just need to know how to try get it a little faster

is there a way to make the twist throttle come on earlier ? and how many magnets does a mtx 1500w rear hub have ?

Hi, thanks for documenting the modification you did. Just a question, I just changed my controler to a more powerful KT controller. I saw you changed to a KT Display, did you had any plugging issues? Or incompatible parts issues?

Thank you sooo much, with the setting P2=6 the speed display and the odometer showed an incorrect value (0 km/h to 4 km/h), after looking through the comments and your explanations, I found the solution quickly: (" ... try the setting at P2 from 6 down to 0..."), with the result, that when setting P2=5 (DIM=29"), the speed display and the odometer work correct!! (Sondors X with Bafang 750W / controller 35amp, battery 60V, wheels 28"x4.9").

You might check the fuses in the battery make sure they are getting a good connection

UK also uses mph. Not kph

I have a 2020 radrunner anyone know the best settings to put it on?

What was the correct offset for the Rover when purchasing the forks? My stock Forks broke looking for new ones found your video ty

Just installed it with these settings. 48v battery showing 53.4 on one bar?

Thank you so much I was struggling to find correct settings for my bike this videos saved. 😊

It would be helpful to know how you ride. Any pedaling? What assist number on the controller? How old the battery? What does battery issues mean?

Lol. I bought the exact same case. Not the size listed on amazon. Loving those tyres. Where did you get those

How do you engage the cruise control while riding? Thank you so much for this video

Pragmatic and clear without getting bogged down by irrelevancies, the best explanation so far. Thank you and good luck with sweet spots :) ~

Really wish you hadn't skipped over the reassembly thats the part i was waiting for! But thanks

Big boss ....I set a password...by mistake....now it's asking me to put it to unlock the colored screen like yours....how to do ....??

It looks like the link to the brake set is no longer valid. Do you have another recommendation for a Radrunner?

Wow thank you so much! Your video solved me an issue with the sensor! Great video!

Thanks, my rad running so much better,

Did you ever zero in on the best P5 setting for the stock battery? I just installed the controller on my 2018 Radrover and am waiting on delivery of a new motor.

Hi I was wondering if you could answer a question when the bike shows my wattage the the wattage always stays on I cannot add some pedal power and lower the wattage the bike is putting out what I mean is if I'm on pas1 say the wattages 200 w I cannot pedal and lower the Watts it will always stay around 200 or so. I was wondering if there's a way to lower the wattage in each pedal assist by pedaling hard to lower the wattage. It always shows a high wattage even if you're pedaling really hard I'm not talking about the settings to lower the wattage output I'm talking more of a pedal hard to make the Watts lower kind of thing. Any ideas thanks in advance.

Hello, I have an issue with my lcd8 It says copy complete and I did not intend to copy anything. Impossible to make it work again. What can I do?

How do you start and stop the cruise control?

Thanks for taking the time to do this

Doooode, it's a couple years too late but medium size needle nose pliers work to snag the internal slots, then use a crescent wrench to rotate the pliers. You would probably need to pre-soak the freewheel nut first with liquid wrench and let it sit for a day. It worked for me.

The brake set is no longer available. Can you recommend another brake set link?

Hi thanks for the video I was wondering if you could answer a quick question? I installed the Bolton controller and I want a little less power on the first couple of pedal assist settings. Do you know if that is possible?

Really fantastic videos! I have watched them all. I have a 2020 RR ST which I too love. I have upgraded to the Bolton controller and their full hydraulic brakes. I didn’t like running the rear brake line outside the frame so I got my LBS to run it inside. Didn’t want to mess with attaching a new hydraulic line or bleeding it. I think they are just 2 piston (?) so they may not be as effective as your 4 piston but they are still really great. RUclips shows all of your videos as having been uploaded a year ago. Are you still around?😀 Any mor RR videos in the works? By the way, the setting for P2 is different for the stock motor and the upgraded motor which Bolton notes in the page of settings that came with my controller in December. Do you find the new controller noisier than the stock one? I do. Many thanks Coop.

It's not a ''Bolton upgrade kit'', it's a ''Kuteng controller kit''. I just got a new version of LCD8H and a 40A sine controller for 130$, saved 100$, thank you very much. And I don't even speak Chinese.

I have a 52v 30ah triangle battery with upgraded Bolton bofang motor and controller with display. Thing is my battery cuts off at 51v meanwhile my brothers bike cuts off at 43v why is that? What do I have to fix in my settings to let me go longer?

My question is how can you hard reset the Odometer? Like the whole odometer since the bike was bought.

Good video. I have a new RR6+ and looking for places to ride in the Portland area. I actually recognized a portion of the trail you rode on for this video! It's the Beaverton Powerline trail. I did not recognize the portion that ran between houses at the beginning of the video. Where is that section located? I'm looking forward to riding on the waterfront trail along the Willamette. Thanks again for the video!

I have one off these screens on my 2000w kit, but it doesn't go as fast as my 15000watt kit with LCD3 DISPLAY, something isn't right with my settings, iv a 700c wheel , can anyone help because even this video doesn't make a difference not matter what I do to my settings

Just wanted to correct the info you gave for p3. when this value is 0, throttle max power is determined by the PAS level. when it's 1, max throttle is allowed regardless of PAS level. So lets say you're in PAS 2 and you are capped at say 10 mph and you start using throttle and P3 = 0 then you will not go over 10 mph. In either setting the throttle is gradual. It DOES NOT make the throttle only on or off when P3 = 0

hey man, dope bike. older video, but i see your still active. i just picked up a radrover stepthru1, i have a set of hookworm tires on my old freestyle 26 bike, do you scrape your cranks on corners when pedaling? i might have to order tubes and throw my old tires on!