Видео

Nice repair & nice vid ... Thx

great video Chip, sorry no Wally, but saw Ruby? My first seeing her. Wow so much rust and wear on that unit. You aways amaze me with your knowledge and creativity.

Nice video ….that’s a typical dumb South Korean LG (Samdung copycat) design😅💪 I love them guys ….I make tons of money fixing their stuff 😅

Hi Chip, I could use some help troubleshooting my 20-year old direct-drive Whirlpool washer. It can still agitate and drain properly but hasn’t been spinning correctly when called upon. The clutch appeared worn, so I replaced it and hoped for the best. Since then, the washer can sometimes wash several loads in a row without issues, but then still intermittently fails to spin at times. Here are some clues that I have gathered so far: When the washer enters a spin cycle, it either works properly the entire time or doesn’t spin at all. It doesn’t cut out if it’s working or kick in when it doesn’t spin at the beginning of the cycle. In instances where the washer fails to spin, I can sometimes get it to spin if I advance the cycle to Extra Rinse or another wash mode. Typically, I just use Normal or Permanent Press, so if it fails to spin in one, I can usually just change modes to make the washer happy again. There have also been times where is alternates between spinning properly for one spin cycle, doing nothing for the next, and then working properly again without intervention. Can you recommend any additional troubleshooting steps to help narrow down the issue? My best guess is that this is an issue with the transmission, but I’d like to go on more than a guess before sinking money into new parts. Given the quality of most newer washers, it seems worth it to keep this one going for a few more years. Any insight would be greatly appreciated! Thanks.

I have to agree with what many of the other folks said; this technician is very thorough and very clear in his instruction; I was able to quickly diagnose our washer issues. Thank you, thank you, thank you!

Great video. Any tips the budget laundry centers or stackables? my laundry closet can't fit side by side.

Is this all new GEs? Geeze, you think they'd fix this

Where the heck is the interior light bulb located at inside the Speed Queen gas dryer? Mine burnt out and I can’t find any reference in the owners manual.

Can one bypass the door switch

Thanks Chip. I just made me a suspension rod puller like yours.

I have one where the drain pump constantly runs and won’t compete cycles. I’m assuming that would be the control board? Any input is appreciated

Thanks man just helped me diagnose my problem, appreciate it

The whirlpool duet dryers are the most fun to work on so many parts to remove just get it apart and I had one with a button that you would have to push and once you pushed it a rod came out so you could hang your clothes on as you take them out of the dryer and it was the most amazing thing i ever seen.

I have an Estate washer and recently it stopped working, now it will still fill with water, but when it comes time for the agitator to start it does nothing, could this be the lid switch or maybe something else like a blown motor maybe?

Man your tub went back in easy. I tried for thirty minutes to get mine back in and it still didn't fall back into place.

I have a TR in one house and a TC in the other. Love the TC. The TR has circuit board issues and shakes the house apart while in Spin.

When I start the test and make it to the 6 o'clock and push the button. It starts filling with water. Should I replace the board

Belt is fine and my resident saying it’s not spinning all the water out could this be speed sensor ?

Your video’s are very informative! I just did the neutral drain repair on my old Whirlpool direct-drive.. which was successful. But since I reinstalled the gearbox it’s been leaking water quite a bit… never leaked before. Why do think removing and reinstalling the gearbox would cause a leak?

What size and where can you get the spanner wrench?

Go with Speed Queen. Commercial grade quality without the unnecessary bells and whistles. There’s a reason they are renowned for laundromat’s.

Sounded like even the bird in the back ground was cracking up and cackling at you finding the “slingshot” thong in the washing hose lol

Hi chip. I have ran the trouble shooting mode and had a stuck button code F2E1 and took the button out (previous owner had it stuck) i ran the same test and no codes. I went to start a large load and it would fill half way up then drain. Same thing with the medium load. But i can wash things on a small load. Ive tried calibrating it but now im at a lost. Can you please point me in the right direction. Thank you!

Chip, great repair. Those tops are always a hassle to open.

Whirlpool should be totally ashamed of themselves. They purchased Maytag, a longtime manufacturer of quality machines. They purchased Kitchen Aid, and they have proceeded to destroy both reputations. They should follow Speed Queen's example. Make a quality product and people will buy it. Make the cheaper stuff for those who can't afford it.

Good fix Chip ... Sadly no train horn Thx for another great vid

Those washer are a gold mine for me. People say they need a control board because that wont drain and the technician replaced the pump and it still wont dain. Its always just a broken wire.like 1 foot up the wires that go to the pump

All and I mean all new ones any brand are JUNK !!

Thanks, good video. This is the repair my GE Hotpoint needs. Plus it probably needs a new belt and rear bearing because it's so old, 25-30 years. It squeaks, on and off, and catches clothes along the top, time to time, but otherwise has never failed me or needed repairs until now. The squeaking started slowly almost 2 years ago and the clothes getting caught about 8 months ago. I recently had my washer fixed by a repairman and also wanted the dryer looked at. He only stuck his head in the drum upside down and told me to buy a new one because it was the bearings and too costly to fix. This GE looks identical to my machine. Would the same kit for work for me? Do you have a video for the rear bearing, by chance? I'm hoping my drum didn't get worn. In that case, I'll buy new.

It may already be in another comment but i watched a different video, disassembled/unclogged/reassembled my drain pump and then none of the lights would work even for diagnostic purposes, it was just humming. Then I stumbled across your video and obviously couldn't start diagnostics without lights.... I watched 10 more videos and stumbled across something called "flood mode" and apparently all I had to do was plug the washed back in and let it hum for 30m to "reset". Flood mode is apparently a thing 😂

Your video is a waste of time. I don't care about all the other crap going on. Please learn to edit your videos. Now to find something helpful.

Thank you!! Some how I have turned on the door lock test mode twice. I do it when I decide to cancel my current load settings and chose another. I think holding the start button to cancel for too long sets it to diagnose. Every time I push start it locks and unlocks but that's it. Holding the start button again to get out of the trouble shooting mode is all it takes to fix. Thank you!!

God Bless you gentlemen here! Single woman here, I know my way around a few things, but not these newer washsers. My brand new 2 year old washer just started doing this, so thanks to you I will know where to look and what to do. Ill try blowing it out first then move forward. Thanks so much for the info. Now to man handle these items in my washing room so I can gain access: my fridge, dryer must be moved to get washer out. Good lord..... I think I will rearrange how these go back in. Thanks again!

Hi Chip my whirlpool ultimate 2 is leaking, it looks like from the transmission? What needs fixing? I thank you for your helpful videos.

Normal use TR5 lasted 6 years. Bearing failure. Repair Tech says not worth repairing You can buy a new one for the price of the repair. Is this true?

By gawd, I followed your video for my dryer and IT WORKED! At least for now it is....THANK YOU!

Thank You for the informative videos!!! Really detailed and makes this easier to understand!!!

Thank you so much! Tapping the relay worked like a charm.

I love my Amana washer and Dryer. Dislike the Whirlpool, clothes come out very wrinkled. .

You stud, you nailed it, mine works but it pulsates like a machine gun? Any thoughts? Thanks

Can you do an upgrade on straightening those spin tubes

I just got the Speed Queen TV2000WN commercial washer and dryer. I’d rather pay double for metal parts and no computer with proven (lack of) technology (totally analog). The washer is about 2x as heavy as the one it replaces. No bells and whistles but I expect these to last a long time.

thank you so much been tech for 7 years and just ran into this problem yesterday for first time and couldn’t believe the fuse burnt out over night and sure enough i go back today check element did exactly what happen on the video thank you for taking time out of your day to explain

Thank you for this! Just bought a new house with a front loader that leaks and is full of mold...needed to replace and was leaning SQ, now I know what I want!:) Do any of them work for a King size blanket?

Thank you for the help.

Thanks Chip! your info helped us make an easy decision. We simply bought the TC5 and DC5 dryer. They replaced our 24 year old Maytag LAT2500AAE and matching gas dryer. Chip the new Speed Queens are virtually identical to our existing 24 year old Maytag machines. They still run well but I would rather replace them before they eventually need repairs!

Chip, thanks for a very informative video…everything exactly what I needed to know to make my purchase.

They better be the best...they are expensive!

Ty for your knowledge

Finally somebody that doesn't talk about a bunch of unnecessary stuff, and knows what he's doing